Honeywell BW Max XT ll Multi Gas Detector Mode d'emploi

Marque: Honeywell

Modèle: BW Max XT ll Multi Gas Detector

Taper: Mode d'emploi

iERP: 129535

D6558/0 [English]

1, 2, 3, and 4-Gas Detector

70596_Max XT OM 1 25/01/11 11:13 AM

iERP: 129535

D6558/0 [English]

1, 2, 3, and 4-Gas Detector

70596_Max XT OM 1 25/01/11 11:13 AM

47255 Max XT II Cover.indd 1 2016-12-12 3:14 PM

Limited Warranty and Limitation Liability

BW Technologies LP (BW) warrants the product to be free from defects in material and workmanship under normal use and service for a period of

two years, beginning on the date of shipment to the buyer. This warranty extends only to the sale of new and unused products to the original buyer.

BW’s warranty obligation is limited, at BW’s option, to refund of the purchase price, repair or replacement of a defective product that is returned to

a BW authorized service center within the warranty period. In no event shall BW’s liability hereunder exceed the purchase price actually paid by the

buyer for the Product.

This warranty does not include:

a) fuses, disposable batteries or the routine replacement of parts due to the normal wear and tear of the product arising from use;

b) any product which in BW’s opinion, has been misused, altered, neglected or damaged, by accident or abnormal conditions of operation,

handling or use;

c) any damage or defects attributable to repair of the product by any person other than an authorized dealer, or the installation of unapproved

parts on the product; or

The obligations set forth in this warranty are conditional on:

a) proper storage, installation, calibration, use, maintenance and compliance with the product manual instructions and any other applicable

recommendations of BW;

b) the buyer promptly notifying BW of any defect and, if required, promptly making the product available for correction. No goods shall be

returned to BW until receipt by the buyer of shipping instructions from BW; and

c) the right of BW to require that the buyer provide proof of purchase such as the original invoice, bill of sale or packing slip to establish that the

product is within the warranty period.

THE BUYER AGREES THAT THIS WARRANTY IS THE BUYER’S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. BW SHALL NOT BE LIABLE FOR ANY

SPECIAL, INDIRECT, INCIDENTAL, OR BASED ON CONTRACT, TORT OR RELIANCE OR ANY OTHER THEORY.

Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or limitation of incidental or consequential

damages, the limitations and exclusions of this warranty may not apply to every buyer. If any provision of this warranty is held invalid or

unenforceable by a court of competent jurisdiction, such holding will not affect the validity or enforceability of any other provision.

Contacting BW Technologies by Honeywell

Email us at: [email protected]

Visit BW Technologies by Honeywell’s website at: www.gasmonitors.com

USA: 1-888-749-8878 Canada: 1-800-663-4164

Europe: +44(0) 1295 700300 Other countries: +1-403-248-9226

GasAlertMaxXT II

Introduction

The Quick Reference Guide provides basic information to oper-

ate the GasAlertMaxXT II gas detector. For complete operating

instructions, refer to the GasAlertMaxXT II Technical Reference

Guide provided on the CD-ROM. The GasAlertMaxXT II gas

detector (“the detector”) is designed to warn of hazardous gas

levels above user-defined alarm setpoints.

The detector is a personal safety device. It is your responsibility

to respond properly to the alarm.

Note

The detector is shipped with English as the default

displayed language. Additional languages provided

are French, German, Spanish, and Portuguese. The

screens for the additional languages are displayed on

the detector and in the corresponding operator’s

manual.

Zeroing the Sensors

To zero the sensors, refer to steps #1-3 in Calibration on

page 9.

Safety Information - Read First

Use the detector only as specified in this operator’s manual and

the technical reference guide, otherwise the protection provided

by the detector may be impaired.

Read the following Cautions before using the detector.

a Cautions

•Warning: Substitution of components may impair Intrinsic

Safety.

• Caution: For safety reasons, this equipment must be

operated and serviced by qualified personnel only. Read

and understand the technical reference guide completely

before operating or servicing.

• Charge the detector before first-time use. BW recommends

the detector be charged after every workday.

• Calibrate the detector before first-time use and then on a

regular schedule, depending on use and sensor exposure

to poisons and contaminants. The sensors must be

calibrated regularly and at least once every 180 days

(6 months).

GasAlertMaxXT II

Quick Reference Guide

• Calibrate only in a safe area that is free of hazardous gas in

an atmosphere of 20.9 % oxygen.

• The combustible sensor is factory calibrated to 50% LEL

methane. If monitoring a different combustible gas in the %

LEL range, calibrate the sensor using the appropriate gas.

• Only the combustible gas detection portion of this

instrument has been assessed for performance by CSA

International.

• Protect the combustible sensor from exposure to lead

compounds, silicones, and chlorinated hydrocarbons.

Although certain organic vapors (such as leaded gasoline

and halogenated hydrocarbons) may temporarily inhibit

sensor performance, in most cases the sensor will recover

after calibration.

• BW recommends that the combustible sensor be checked

with a known concentration of calibration gas after any

exposure to contaminants/poisons such as sulfur

compounds, silicon vapors, halogenated compounds, etc.

• BW recommends to bump test the sensors before each

day’s use to confirm their ability to respond to gas by

exposing the detector to a gas concentration that exceeds

the alarm setpoints. Manually verify that the audible and

visual alarms are activated. Calibrate if the readings are not

within the specified limits.

• Caution: High off-scale LEL readings may indicate an

explosive concentration.

• Any rapid up scaling reading followed by a declining or

erratic reading may indicate a gas concentration beyond

upper scale limit, which can be hazardous.

• For use only in potentially explosive atmospheres where

oxygen concentrations do not exceed 20.9% (v/v).

• Extended exposure of the GasAlertMax XT II to certain

concentrations of combustible gases and air may stress the

detector element that can seriously affect its performance. If

an alarm occurs due to a high concentration of combustible

gases, recalibration should be performed, or if needed, the

sensor replaced.

• The BW pump (XT-RPUMP-K1) is certified for use with the

GasAlertMax XT II only.

•Warning: The lithium battery (MX-BAT01) may present a risk

of fire or chemical burn hazard if misused. Do not

disassemble, heat above 212°F (100°C), or incinerate.

•Warning: Do not use any other lithium batteries with the

GasAlertMax XT II detector. Use of any other cell can cause

fire and/or explosion. To order and replace the MX-BAT01

lithium battery, contact BW Technologies by Honeywell.

•Warning: Lithium polymer cells exposed to heat at 266°F

(130°C) for 10 minutes can cause fire and/or explosion.

• Dispose of used lithium cells immediately. Do not

disassemble and do not dispose of in fire. Do not mix with

the solid waste stream. Spent batteries must be disposed

of by a qualified recycler or hazardous materials handler.

• Keep lithium cells away from children.

• Calibrations and bump tests can be performed using a

0.5 l/min. regulator or a demand flow regulator. If the demand

flow regulator is used, it must meet the following maximum

inlet pressure specifications:

• Disposable cylinders 0-3000 psig/70 bar

• Refillable cylinders 0-3000 psig/70 bar

GasAlertMaxXT II

Informations sur la sécurité - À lire avant toute chose

• Products may contain materials that are regulated for

transportation under domestic and international danger-

ous goods regulations. Return product in compliance with

appropriate dangerous goods regulations. Contact freight

carrier for further instructions.

Informations sur la sécurité - À lire avant

toute chose

Respectez strictement les instructions d'emploi figurant dans ce

manuel d'utilisation ainsi que dans le guide technique, sinon, la

protection offerte par le détecteur pourrait être diminuée.

Lisez les Précautions suivantes avant d'utiliser le détecteur.

a Précautions

•Avertissement: Le remplacement d'un composant de

l'appareil peut altérer sa sécurité intrinsèque.

• Précaution: Pour des raisons de sécurité, cet appareil doit

être exclusivement utilisé et entretenu par du personnel

qualifié. Lisez attentivement le guide technique avant

• d'utiliser l'appareil ou d'en assurer l'entretien, et assurez-

vous d'en avoir bien compris les instructions.

• Chargez le détecteur avant sa première utilisation. BW

recommande de recharger le détecteur après chaque

journée d'utilisation.

• Étalonnez le détecteur avant sa première utilisation, puis de

manière régulière, en fonction de l'utilisation et de

l'exposition du capteur aux poisons et autres contaminants.

Les capteurs doivent être étalonnés régulièrement et au

moins une fois tous les 180 jours (6 mois).

• Veillez à effectuer l'étalonnage dans une zone sûre, exempte

de gaz dangereux, dans une atmosphère contenant 20,9 %

d'oxygène.

• Le capteur de gaz combustible est étalonné en usine au

méthane à une concentration de 50% LIE. Si la surveillance

porte sur un autre gaz combustible dans la plage de %LIE,

étalonnez le capteur en utilisant le gaz approprié.

• Sur cet appareil, seule la détection de gaz combustible a fait

l'objet d'une évaluation des performances par CSA

International.

• Protégez le capteur de gaz combustible des expositions aux

composés de plomb, aux silicones et aux hydrocarbures

chlorés. Bien que certaines vapeurs organiques (comme

l'essence au plomb ou les hydrocarbures halogénés)

puissent neutraliser provisoirement les performances du

capteur, dans la plupart des cas, le capteur retrouvera son

fonctionnement normal après étalonnage.

• Si le capteur de gaz combustible a été exposé à des

contaminants/poisons (composés de soufre, vapeurs de

silicium, produits halogénés, etc.), il est conseillé de vérifier

son bon fonctionnement en le mettant en présence d'une

concentration connue d'un gaz.

• BW recommande d'effectuer un " test fonctionnel " des

capteurs, avant chaque utilisation quotidienne, afin de

vérifier qu'ils réagissent bien au gaz, notamment lorsque le

détecteur est exposé à une concentration de gaz qui

dépasse les seuils d'alarme. Vérifiez manuellement que les

alarmes sonore et visuelle sont activées. Étalonnez

l'appareil si les lectures sont en dehors des limites

spécifiées.

• Précaution: Des lectures élevées hors échelle peuvent

indiquer la présence d'une concentration explosive.

GasAlertMaxXT II

Quick Reference Guide

• Une lecture qui augmente rapidement, puis qui baisse, ou

une lecture fantaisiste peuvent être représentatives d'une

concentration de gaz excédant la limite d'échelle supérieure

et risquant donc d'être dangereuse.

• Cet appareil est uniquement destiné aux atmosphères

potentiellement explosives où la concentration d'oxygène

ne dépasse pas 20,9 % (v/v).

• L'exposition prolongée du GasAlertMax XT II à certaines

concentrations de gaz combustible et d'air peut fortement

éprouver l'élément du détecteur et nuire gravement à ses

performances. En cas d'alarme, suite à une forte

concentration de gaz combustible, il convient d'effectuer un

réétalonnage, voire de remplacer le capteur si nécessaire.

• La pompe BW (XT-RPUMP-K1) est certifiée pour une

utilisation avec le GasAlertMax XT II uniquement.

•Avertissement: La batterie au lithium (MX-BAT01) peut

présenter un risque d'incendie ou de brûlure chimique en

cas de mauvaise utilisation. Elle ne doit jamais être

démontée, incinérée ni chauffée au-delà de 100 °C.

•Avertissement: N'utilisez jamais d'autres piles au lithium

avec le détecteur GasAlertMax XT II, au risque de provoquer

un incendie et/ou une explosion. Pour commander une

batterie au lithium MX-BAT01 de rechange, contactez BW

Technologies by Honeywell.

•Avertissement: Les piles au lithium polymère exposées

à une température supérieure à 130 °C pendant plus de

10 minutes peuvent provoquer un incendie et/ou une

explosion.

• Mettez immédiatement au rebut les piles au lithium usagées.

Ne les démontez jamais et ne les jetez pas au feu. Ne les

mélangez pas aux autres déchets solides. Les piles usagées

doivent être éliminées par un centre de recyclage agréé ou

un centre de traitement des matières dangereuses.

• Gardez les piles au lithium hors de portée des enfants.

•Avertissement: BW Technologies recommande l'utilisation

de gaz d'étalonnage de haute qualité et de bouteilles

répondant aux normes nationales. Les gaz d'étalonnage

doivent correspondre à la précision du détecteur.

• Les tests fonctionnels et les étalonnages peuvent être

effectués en utilisant un régulateur 0,5 l/min. ou un

régulateur de débit à la demande. Si vous utilisez le régu-

lateur de débit à la demande, ce dernier doit répondre aux

spécifications de pression d'entrée maximale suivantes :

• Bouteilles jetables 0-3 000 psig/70 bar

• Bouteilles rechargeables 0-3 000 psig/70 bar

• Les produits peuvent contenir des matériaux qui sont

réglementés pour le transport en vertu des règlements

nationaux et internationaux de marchandises dangereuses.

Retourner le produit conformément à la réglementation sur

les marchandises dangereuses appropriées. Contactez

transporteur pour plus d'instructions.

GasAlertMaxXT II

Parts of the GasAlertMaxXT II

Item Description

1Visual alarm indicators (LEDs)

2Pump quick connector

3Pump filter and moisture filter

4Pushbutton

5Alligator clip

6Charging connector and IR interface

7Diffusion cover locking screw (1)

8Diffusion cover

9Audible alarm

10 Liquid crystal display (LCD)

GasAlertMaxXT II

Quick Reference Guide

Display Elements

Item Description

1Alarm condition

2Automatically zero sensor

3Numeric values

4Battery life indicator

5Pump indicator

6Heartbeat indicator

7Gas type identifiers

8Gas cylinder

9Automatically span sensor

GasAlertMaxXT II

Pushbutton

Pushbutton Description

• To activate the detector, press C.

• To deactivate the detector, press and hold C until the OFF countdown is complete.

• To view the date/time, TWA, STEL, and maximum (MAX) readings, press C twice rapidly. To clear

the TWA, STEL, and MAX readings, press C when the LCD displays CLEAR ALL.

• To initiate calibration, press and hold C while the detector performs the OFF countdown. Continue

holding C while the LCD briefly deactivates and then reactivates to begin the CAL countdown.

Release C when the CAL countdown is complete.

• To activate the backlight, press C and release.

• To acknowledge latched and pump alarms, press C.

• To acknowledge a low alarm and disable the audible alarm, press C. The Low Alarm Acknowl-

edge option must be enabled in Fleet Manager II.

• To acknowledge any of the Due Today alarms (calibration, bump test, block test) and disable the

audible alarm, press C.

GasAlertMaxXT II

Quick Reference Guide

Calibration and Bump Test Installation

GasAlertMaxXT II

Calibration

a Caution

Calibrate only in a safe area that is free of hazardous gas

in an atmosphere of 20.9 % oxygen. Do not calibrate the

detector during or immediately after charging is complete.

Note

The maximum hose length for calibration is 3 ft. (1 m).

Note

Calibration can be aborted at any time. To abort

calibration, press C. The CAL ABORTED screen

displays.

1. Press and hold C as the detector

performs the OFF countdown. Continue

to hold C when the detector briefly

deactivates.

2. The detector activates again and

performs the CAL countdown. Continue

to hold C until the countdown is

complete to enter calibration.

3. flashes while the detector

zeroes all of the sensors.

If a sensor fails to auto zero, it cannot be

spanned. When auto zero is complete,

the LCD displays APPLY GAS.

4. Refer to Calibration and Bump Test

Installation (page 6). Attach the

0.5 l/min. regulator or the demand

flow regulator and apply gas.

Note

The diffusion cover must be attached

to the detector to calibrate.

K flashes on the LCD. After a sufficient

amount of gas has been detected

(30 seconds), the detector beeps.

flashes while the detector

completes the span.

5. The LCD displays CAL DUE. Next, a

screen displays showing the number of

days remaining before calibration is due

for each sensor. Last, the LCD displays

(e.g.) CAL DUE 180 d. As some

sensors require more frequent

calibrations, the LCD displays the earliest

calibration that must be performed.

GasAlertMaxXT II

Quick Reference Guide

Alarms

Refer to the following table for information about alarms and corresponding screens.

Note

If the Low Alarm Acknowledge option is enabled in Fleet Manager II, the low alarm can be acknowledged and the audible

alarm deactivated by pressing C. If the alarm escalates to a high, STEL, TWA, or multi-gas alarm, the audible alarm

reactivates.

Alarm Screen Alarm Screen

Low Alarm

• Slow siren

• Slow alternating flash

•L and target gas bar flash

• Vibrator alarm activates

TWA Alarm

• Fast siren

• Fast alternating flash

•L and target gas bar flash

• Vibrator alarm activates

High Alarm

• Fast siren

• Fast alternating flash

•L and target gas bar flash

• Vibrator alarm activates

STEL Alarm

• Fast siren

• Fast alternating flash

•L and target gas bar flash

• Vibrator alarm activates

Multi-Gas Alarm

• Alternating low and high alarm siren

and flash

•L and target gas bars flash

• Vibrator alarm activates

Over Limit (OL) Alarm

• Fast siren

• Fast alternating flash

•L and target gas bar flash

• Vibrator alarm activates

GasAlertMaxXT II

Alarms

Note:

If enabled, during an alarm condition the Latched Alarms option causes the low and high gas alarms (audible, visual, and vibrator) to persist

until the alarm is acknowledged (by pressing C) and the gas concentration is below the alarm setpoint. The LCD continues to display the

high peak concentration until the alarm condition no longer exists. Enable/disable Latching Alarms in Fleet Manager II. Local regulations may

require the Latching Alarms option be enabled.

Alarm Screen Alarm Screen

Sensor Alarm

•ERR displays

Automatic Deactivation Alarm

• Sequence of 10 rapid sirens and alter-

nating flashes with 1 second of silence

in between (reactivates seven times)

•L flashes and the vibrator alarm

activates

•TURNING OFF displays before the

detector deactivates

Low Battery Alarm

• Sequence of 10 rapid sirens and alternat-

ing flashes with 7 seconds of silence in

between (continues for 10 minutes)

• and L flashes

•LOW BATTERY displays and the vibrator

alarm activates

• After 10 minutes, a sequence of 10 rapid

sirens and alternating flashes with 1 sec-

ond of silence in between (reactivates

seven times)

•TURNING OFF displays before the

detector deactivates

Pump Alarm

• Two beeps and two flashes

•J and L flashes

•HIGH displays

• The vibrator alarm activates

GasAlertMaxXT II

Quick Reference Guide

Options Menu

The detector, IR Link adapter, and Fleet Manager II software

are required to define options. Refer to the GasAlertMax XT II

Technical Reference Guide and Fleet Manager II Operator’s

Manual. For user and sensor options, refer to the following:

Device Configuration

•Startup Message Top Line: Enter a line of text to display on

the LCD during startup (maximum 25 characters).

•Startup Message Bottom Line: Enter a line of text to dis-

play on the LCD during startup (maximum 25 characters).

•Lockout on Self-Test Error (sensor alarm lock): If a

sensor fails during startup and the Lockout on Self-Test

option is enabled, Safety Lock On displays on the LCD and

the detector deactivates.

•Safe Mode: If enabled, SAFE displays continuously on the

LCD unless an alarm condition occurs.

•Confidence Beep: If enabled, the confidence beep provides

continuous confirmation that the detector is operating correctly.

To define how often the detector beeps (every 1-120 seconds),

enter the value in the Confidence Interval field. Confidence

beep is automatically disabled during a low battery alarm.

•Latching Alarms: Enable to ensure an alarm persists until

the alarm is acknowledged and the gas concentrations are

below the alarm setpoint. The audible alarm can be temporarily

deactivated for 30 seconds by pressing C, but the LCD contin-

ues to display the high peak concentration until the alarm con-

dition no longer exists.

•Force Calibration: If enabled, the detector must be

calibrated if a sensor is overdue upon startup. User defined (0-

365 days) in the Calibration Interval field.

•Cal IR Lock (must use IR device to calibrate): If enabled, the

detector automatically auto zeros, but the sensors must be

spanned using the IR Link or MicroDock II station with Fleet

Manager II.

•Force Bump: If enabled, a bump test must be performed to

ensure the sensor(s) are responding correctly to the test gas.

User defined (0-365 days) in the Bump Interval field.

•Location Logging: If enabled, a series of numbers

(1-999) can be entered on the detector to identify gas

wells, plants, and other areas that identify the location where

the detector is being used.

•Force Block Test: If enabled, a pump block test must

be performed during the startup tests.

•Datalog Interval (seconds): Define how often the

detector records a sample (every 1-120 seconds).

•Confidence Interval (seconds): Define how often the

detector beeps (1-120 seconds) when the Confidence Beep

option is enabled.

•Language: The LCD displays the screens in English,

Français (French), Deutsch (German), Español

(Spanish), or Português (Portuguese). Select the

language from the drop-down menu in Fleet Manager II.

Sensor Configuration (H2S, CO, LEL, and O2)

•Sensor Disabled: Enables/disables the selected sensor.

•Calibration Gas (ppm): Define the span gas concentration

for each sensor. The span gas concentration must match the

span value on the gas cylinder.

•Calibration Interval (days): Define the number of days (0-

365) when the next calibration is due.

•Bump Interval (days): Define the number of days (0-365)

when the next bump test is due.

•Low Alarm (ppm): Define the low alarm setpoint for each

sensor.

•High Alarm (ppm): Define the high alarm setpoint for each

sensor.

GasAlertMaxXT II

Maintenance

•TWA Alarm (ppm): Define the time-weighted average (TWA)

alarm setpoint (toxic sensors only).

•STEL Alarm (ppm): Define the short-term exposure limit

(STEL) alarm setpoint (toxic sensors only).

•STEL Interval (minutes): Define the short-term exposure

limit (STEL) from 5-15 minutes (toxic sensors only).

•TWA Period (hours) (TWA moving average (hours): The

TWA Period option is used to define a time-weighted mov-

ing average of accumulated gases over a period of 4-16

hours, to ensure the worker leaves the area when

the defined maximum average is accumulated.

•Correction Factor (%): Enter the compensation factors for

hydrocarbons other than methane. The factor can only be

applied if the LEL sensor has been calibrated with methane

(LEL only).

•50% LEL = (%CH4): Enter a percentage value to display the

LEL reading as %vol., assuming a methane environment (LEL

only).

•Auto-Zero on Startup: Enable/disable the detector to auto-

matically zero the sensor(s) during startup (H2S, CO, LEL, and

O2).

•LEL by Volume CH4: If enabled, the detector operates

assuming a methane (CH4) calibration. Enable to read and dis-

play %CH4 values. Disable to read and display %LEL values.

•5% LEL Over-span: If enabled, the detector automatically

over-spans the LEL sensor by 5% LEL above the span gas

concentrations to ensure the detector is in compliance with

CAN/CSA C22.2 No. 152.

•20.8% Base Reading: When enabled, the detector is

configured to detect 20.8% O2 as ambient air. When

disabled, the detector is configured to detect 20.9% O2

as ambient air.

•Low Alarm Acknowledge: If enabled, the audible

alarm can be temporarily disabled during a low alarm

by pressing C. The vibrator, alarm LEDs, and LCD

remain operational (toxic and LEL only).

Maintenance

To maintain the detector in good operating condition, perform

the following basic maintenance as required.

• Calibrate, bump test, and inspect the detector on a regular

schedule.

• Maintain an operations log of all maintenance, bump tests, cali-

brations, and alarm events.

• Clean the exterior with a soft damp cloth. Do not use solvents,

soaps, or polishes.

• Do not immerse the detector in liquids.

Charging the Detector

a Warning

Charge only in a safe area that is free of hazardous gas

within temperatures of 32°F-113°F (0°C-45°C).

Charge the battery after each workday. To charge the battery,

refer to the following procedures and illustration:

1. Deactivate the detector.

2. Insert the charging adapter plug into an AC outlet.

3. Connect the charging adapter to the detector IR

receptacle. Refer to the following illustration.

4. Allow the battery to charge for 6 hours.

GasAlertMaxXT II

Quick Reference Guide

5. To reach full battery capacity, allow a new battery to

fully charge and discharge three times.

Replacing a Sensor or Sensor Filter

a Warning

To avoid personal injury and/or property damage, only

use sensors that are specifically designed for the

detector.

Note

Detectors that are configured for 1, 2, or 3 gases may

contain a dummy sensor in one of the four sensor

locations.

To replace a sensor or sensor filter, refer to the following figure,

table and procedures #1-13.

GasAlertMaxXT II

Maintenance

GasAlertMaxXT II

Quick Reference Guide

1. Deactivate the detector.

2. Remove the pump inlet screw and the pump inlet.

3. Remove the six machine screws from the rear shell.

4. Because the pump hose is connected to the rear

shell and front shell pump, carefully remove the rear

shell by lifting upward and tilting to the left. Both the

rear and front shell are laying flat side by side.

5. Remove the two PCB screws.

6. Lift the PCB upward and tilt to the left. Lay the PCB

(sensors facing up) onto the rear shell.

Item Description

1Front shell

2LEL sensor

3PCB

4PCB screws (2)

5Pump

6Rear shell

7Machine screws (6)

8Pump inlet

9Pump filter (particulate)

10 Moisture filter

11 CO sensor

12 H2S sensor

13 O2 sensor

14 Sensor filter

GasAlertMaxXT II

Specifications

7. Slide the LEL, CO, and H2S sensor(s) outward to

remove.

To remove the oxygen sensor, gently insert a screw-

driver to the back of the oxygen sensor to push out

the sensor.

8. Insert the new sensor(s) and replace the sensor filter.

9. Reassemble the detector and replace the two PCB

screws.

10. Replace the six machine screws.

11. If required, replace the pump and moisture filter.

12. Replace the pump inlet and the pump inlet screw.

13. Activate the detector and then calibrate the new

sensor(s). Refer to Calibration.

Specifications

Instrument dimensions: 13.1 x 7.0 x 5.2 cm

(5.1 x 2.8 x 2.0 in.)

Weight: 328 g (11.6 oz.)

Operating temperature: -20°C1 to +50°C (-4°F to +122°F)

Storage temperature: -40°C1 to +60°C (-40°F to +140°F)

Operating humidity: 10% to 100% relative humidity

(non-condensing)

Dust and moisture ingress: IP66/IP67

Alarm setpoints: May vary by region and are user-defined

Detection range:

H2S: 0 - 200 ppm (1 ppm increments)

CO: 0 - 1000 ppm (1 ppm increments)

O2: 0 - 30.0% vol. (0.1% vol. increments)

Combustible (LEL): 0 - 100% (1% LEL increments) or

0-4.4% v./v CH4

1. Standard release data. This product has extended

characteristics. For specifications refer to EAC Ex

certificate and Pattern Approval document.

GasAlertMaxXT II

Quick Reference Guide

Sensor type:

H2S, CO, O2: Single plug-in electrochemical cell

Combustibles: Plug-in catalytic bead

O2 measuring principle: Capillary controlled concentration

sensor

Alarm conditions: TWA alarm, STEL alarm, low alarm, high

alarm, multi-gas alarm, over limit (OL) alarm, low battery alarm,

confidence beep, automatic deactivation alarm, and pump

alarm

Audible alarm: 95 dB+ at 30 cm variable pulsed beeper with

full battery charge

Visual alarm: Red light-emitting diodes (LEDs)

Display: Alphanumeric liquid crystal display (LCD)

Backlight: Activates upon startup and when the pushbutton is

pressed; deactivates after 10 seconds. Also activates during an

alarm condition and remains lit until alarm ceases

Self-test: Initiated at activation and tests continuously

Calibration: Automatic zero and automatic span

User field options: Startup message, lockout on self-test error,

safe mode, confidence beep, latching alarms, force calibration,

cal IR lock, force bump, location logging, force block test,

set datalog interval, set confidence interval, language selection

Sensor options: Sensor enable/disable, set span calibration

values, set calibration interval, set bump interval, set alarm

setpoints, set STEL interval, set TWA period, auto zero at

startup enable/disable, 5% over span, low alarm acknowledge,

oxygen measurement, and combustible gas measurement

Battery operating time:

One rechargeable lithium polymer: 13 hours (typical)

Year of manufacture: The detector's year of manufacture is

determined from the serial number. The second and third num-

ber after the second letter determines the year of manufacture.

E.g., MA 110-000001 = 2010 year of manufacture

Approved batteries:

North America

Approved batteries for GasAlertMax XT II product:

Lithium-ion polymer battery as per standards EN50020, UL913,

C22.2 No. 157

Rechargeable battery (MX-BAT01) Temperature code

Lithium polymer -20°C ≤ Ta ≤ +50°C T4

Battery charger: charging adapter

First-time charge: 6 hours

Normal charge: 6 hours

Warranty: 2 years including sensors

Approvals:

Approved by CSA to both U.S. and Canadian Standards

CAN/CSA C22.2 No. 157 and C22.2 152

La page charge ...

Honeywell BW Max XT ll Multi Gas Detector Mode d'emploi

Marque: Honeywell

Modèle: BW Max XT ll Multi Gas Detector

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Honeywell BW Max XT ll Multi Gas Detector User guide

Honeywell BW Max XT ll Multi Gas Detector Mode d'emploi

Honeywell BW Max XT ll Multi Gas Detector Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents