SIMPLE MANUAL
Wireless
Sound Bar
Please read this manual carefully before operating your set and retain it for
future reference.
To view the instructions of advanced features, visit http://www.lg.com and
then download Owner’s Manual. Some of the content in this manual may
differ from your unit.
MODEL
SN5R
www.lg.com
Copyright © 2020 LG Electronics Inc. All Rights Reserved.1912_Rev01
MFL71672708
ENGLISH
SN5R.DCANLLK_SIM_ENG_MFL71672708.indd 1 2020-02-03 8:05:47
Front Panel
The buttons are located on the side.
1 (Standby) ············Switches the unit ON or OFF.
F (Function) ··························Selects function.
p/o (Volume)······················ Adjusts volume.
Rear Panel
DC IN·····················Connect to the AC adapter.
OPTICAL IN ············Connect to an optical device.
HDMI IN ··········Connect to device with HDMI OUT.
HDMI OUT (TV ARC)··············· Connect to a TV.
USB Port ····················Connect to a USB device.
Make sure to properly align and connect
the optical cable; improper alignment may
cause damage to the jack.
Subwoofer Connection
Place the wireless subwoofer near the sound bar and
follow steps below.
a Connect the power cord of the sound bar and the
wireless subwoofer to the outlet.
b Turn on the sound bar.
• The sound bar and wireless subwoofer will be
automatically connected. The subwoofer's
green LED turns on.
Manual Subwoofer Connection
If the subwoofer does not make sound, try to
connect manually.
a Press PAIRING on the rear of the wireless
subwoofer.
• The green LED on the rear of the wireless
subwoofer blinks quickly.
(If the green LED does not blink, press and
hold the PAIRING.)
b Turn on the sound bar.
• Pairing is completed. The green LED on the
rear of the wireless subwoofer turns on.
Keep the sound bar and the subwoofer
away from the device (ex. wireless router,
microwave oven, etc.) over 1 m (3.3 ft) to
prevent wireless interference.
!
1 m
(3.3 ft)
SN5R.DCANLLK_SIM_ENG_MFL71672708.indd 2 2020-02-03 8:05:50
TV Connection
Connect the sound bar and TV using Optical ( ) or
HDMI ARC ( ).
Optical Connection
a Connect the sound bar to the TV using Optical
cable.
b Set up [External Speaker (Optical)] on your TV
setting menu.
TV
HDMI (ARC) Connection
a Connect the sound bar to the TV using HDMI
cable.
b Set up [External Speaker (HDMI ARC)] on your
TV setting menu.
TV
• HDMI connection is unavailable if your TV
does not support HDMI ARC.
• If this unit is connected by OPTICAL and
ARC at the same time, the ARC signal
has a higher priority.
Additional Device Connection
a Connect to the external device like as follow.
TV
OR
(Set-top Box,
Player etc.)
OR
b Set the input source by pressing F repeatedly.
Remote control
Replacement of Battery
C/V: Skip/Search
N: Play/Pause
- Bluetooth connection lock (BT LOCK): Select
the Bluetooth function by pressing F repeatedly.
Long press N and press it again to limit
Bluetooth connection to only BT and LG TV.
SOUND EFFECT: Selects a sound effect mode.
- TV remote: Long press SOUND EFFECT and
press it again to use TV remote control.
FOLDER W/S: Searches a folder.
J:Displaystheinformationofale,aninputsource
or connected Bluetooth device name.
- Auto Power ON/OFF: Long press J and press
it again.
: Adjusts sound level of each speaker.
- Surround sound: Long press
and press it
again.
REPEAT:Listenstoyourlesrepeatedlyorrandomly.
SN5R.DCANLLK_SIM_ENG_MFL71672708.indd 3 2020-02-03 8:05:51
Additional Information
Specication
Power
consumption
Refer to the main label.
AC adapter
• Model : DA-50F25
• Manufacturer : Asian Power
Devices Inc.
• Input : 100 - 240 V ~
50 - 60 Hz
• Output : 25 V 0 2 A
Dimensions
(W x H x D)
Approx.
890.0 mm X 57.0 mm X
85.0 mm With foot
(35 inch x 2.2 inch x 3.3 inch)
Bus Power
Supply
(USB)
5 V 0 500 mA
Amplier
(Total RMS
Output
power)
520 W RMS
Designandspecicationsaresubjecttochange
without notice.
Rear Surround sound
Wireless Rear Speakers Kit included for real
surround sound. (SPJ4-S)
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
To obtain the source code under GPL, LGPL, MPL, and
other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license
terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to
you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of
media, shipping, and handling) upon email request to
opensourc[email protected].
This offer is valid for a period of three years after our
last shipment of this product. This offer is valid to
anyone in receipt of this information.
SN5R.DCANLLK_SIM_ENG_MFL71672708.indd 4 2020-02-03 8:05:52
Industry Canada Statement
[For having wireless function (WLAN, Bluetooth,...)]
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
CAN ICES-3 (B)/NMB-3 (B)
IC Radiation Exposure Statement
[For having wireless function (WLAN, Bluetooth,...)]
This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20 cm (7.8 inches) between the
antenna & your body.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE
FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
WARNING
[For product having the wireless function using 5 GHz
frequency bands]
i. the device for operation in the band 5150–5250
MHz is only for indoor use to reduce the potential
for harmful interference to co-channel mobile
satellite systems;
ii. for devices with detachable antenna(s), the
maximum antenna gain permitted for devices in the
bands 5250-5350 MHz and 5470-5725 MHz shall
be such that the equipment still complies with the
e.i.r.p. limit;
iii. for devices with detachable antenna(s), the
maximum antenna gain permitted for devices in
the band 5725-5850 MHz shall be such that the
equipment still complies with the e.i.r.p. limits as
appropriate; and
iv. [for devices operating in the band 5250-5350 MHz
having an e.i.r.p. greater than 200 mW] antenna
type(s), antenna models(s), and worst-case tilt
angle(s) necessary to remain compliant with the
e.i.r.p. elevation mask requirement set forth in
section 6.2.2.3 of RSS-247 shall be clearly indicated.
Users should also be advised that high-power radars
are allocated as primary users (i.e. priority users) of the
bands 5250-5350 MHz and 5650-5850 MHz and that
these radars could cause interference and/or damage to
LE-LAN devices.
SN5R.DCANLLK_SIM_ENG_MFL71672708.indd 5 2020-02-03 8:05:52
LG Customer Information Center
1-888-542-2623 CANADA
Register your product Online!
www.lg.com
SN5R.DCANLLK_SIM_ENG_MFL71672708.indd 6 2020-02-03 8:05:52
a Connect the power cord of wireless receiver to
the outlet.
b Turn on the unit: The unit and wireless receiver
will be automatically connected. The receiver's
yellow - green LED turns on.
Wireless Receiver Connection Manually
If the rear speakers do not make sound, try to
connect manually.
a Press PAIRING button on the rear of the
wireless receiver.
y
The yellow - green LED on the wireless receiver
blinks quickly.
b Turn on the main unit.
c Pairing is completed.
y
The yellow - green LED on the wireless receiver
turns on.
Rear Speakers Connection1 Wireless Receiver Connection2
a Connect the speaker cables to rear speakers
correctly.
b Connect the Wireless Receiver and the rear
speakers (Blue: left, Grey: right) with the speaker
cables.
c Turn on the Surrond function to enjoy surround
sound.
Speaker design and connection method may be
different according to models.
Rear speaker
(Left)
Wireless
Receiver
Rear speaker
(Right)
Transparent
Black stripe
Transparent
Black stripe
Additional Information
Specication of Wireless reciever
Power
requirement
Refer to the main label on the
wireless receiver.
Power
consumption
Refer to the main label on the
wireless receiver.
Dimensions
(W x H x D)
Approx.
60 mm x 220 mm x 175 mm
(2.4 inch x 8.7 inch x 6.9 inch)
Design and specications are subject to change
without notice.
About Ferrite Core (Optional)
twice
Surround Sound On/Off
When you turn on surround function, you can enjoy
magnificent surround sound for all the input sound
source with rear speakers.
The initial setting for the surround function is
OFF, turn the surround function ON to use it.
Surround On: Press and hold button on the remote
control about 3 seconds and then press button
repeateadly to select ON - SURROUND in the display
window.
Surround Off: Press and hold
button on the
remote control about 3 seconds and then press
button repeateadly to select OFF - SURROUND in the
display window.
Industry Canada Statement
[For having wireless function (WLAN, Bluetooth,...)]
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
CAN ICES-3 (B)/NMB-3 (B)
IC Radiation Exposure Statement
[For having wireless function (WLAN, Bluetooth,...)]
This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20 cm (7.8 inches) between the
antenna & your body.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE
FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
WARNING
[For product having the wireless function using 5 GHz
frequency bands]
i. the device for operation in the band 5150–5250
MHz is only for indoor use to reduce the potential
for harmful interference to co-channel mobile
satellite systems;
ii. for devices with detachable antenna(s), the
maximum antenna gain permitted for devices in the
bands 5250-5350 MHz and 5470-5725 MHz shall
be such that the equipment still complies with the
e.i.r.p. limit;
iii. for devices with detachable antenna(s), the
maximum antenna gain permitted for devices in
the band 5725-5850 MHz shall be such that the
equipment still complies with the e.i.r.p. limits as
appropriate; and
iv. [for devices operating in the band 5250-5350 MHz
having an e.i.r.p. greater than 200 mW] antenna
type(s), antenna models(s), and worst-case tilt
angle(s) necessary to remain compliant with the
e.i.r.p. elevation mask requirement set forth in
section 6.2.2.3 of RSS-247 shall be clearly indicated.
Users should also be advised that high-power radars
are allocated as primary users (i.e. priority users) of the
bands 5250-5350 MHz and 5650-5850 MHz and that
these radars could cause interference and/or damage to
LE-LAN devices.
www.lg.com
Copyright © 2020 LG Electronics Inc. All Rights Reserved.2005_Rev02
MFL71672724
SIMPLE MANUAL
Wireless Rear Speakers
Kit
Please read this manual carefully before operating your set and retain it for
future reference.
To view the instructions of advanced features, visit http://www.lg.com and
then download Owner’s Manual. Some of the content in this manual may
differ from your unit.
MODEL
SPJ4-S
ENGLISH
LG Customer Information Center
1-888-542-2623 CANADA
Register your product Online!
www.lg.com
Set the distance between the sound bar and
the wireless receiver as close as possible and
keep them away from the device (ex. wireless
router, microwave oven, etc.) over 1 m (3.3 ft)
to prevent wireless interference.
> 1 m
(3.3 ft)
SPJ4-S(SN5R).DCANLLK_SIM (Sheet)_MFL71672724.indd 1-4 2020-04-21 3:44:19
a Branchez le cordon d’alimentation du récepteur
sans l dans la prise.
b Mettez l’appareil principal en marche : l’appareil
et le récepteur sans l seront automatiquement
connectés. Le voyant à DEL vert-jaune du
récepteur s’allume.
Connectez manuellement le récepteur
sans fil
Si les haut-parleurs arrière ne produisent pas de son,
essayez de les connecter manuellement.
a Appuyez sur la touche PAIRING (jumelage) à
l’arrière du récepteur sans l.
y
Le voyant à DEL jaune-vert du récepteur sans
l clignote rapidement.
b Mettez l’appareil principal en marche.
c Le jumelage est terminé.
y
Le voyant à DEL jaune-vert du récepteur sans
l s’allume.
Connexion des haut-parleurs arrière
1
Connexion du récepteur sans l
2
a Connectez correctement les câbles des haut-
parleurs aux haut-parleurs arrière.
b Connectez le récepteur sans l et les haut-
parleurs arrière (bleu : haut-parleur gauche,
gris : haut-parleur droit) aux câbles des haut-
parleurs.
c Activez la fonction Ambiophonie pour proter du
son avec effet ambiophonique.
La conception et la méthode de connexion des
haut-parleurs peuvent être différentes selon
les modèles.
Informations supplémentaires
Caractéristiques du récepteur sans l
Exigences
électriques
Consultez l’étiquette principale
du récepteur sans l.
Consommation
d’énergie
Consultez l’étiquette principale
du récepteur sans l.
Dimensions
(L x H x P)
Environ
60 mm x 220 mm x 175 mm
(2,4 po x 8,7 po x 6,9 po)
La conception et les caractéristiques peuvent faire
l’objet de modications sans préavis.
À propos du tore magnétique (en option)
Deux fois
Activation et désactivation du son ambiophonique
Lorsque vous activez la fonction Ambiophonie, vous
pouvez profiter d’un magnifique son ambiophonique
de toutes les sources d’entrée audio avec des haut-
parleurs arrière.
Par défaut, la fonction Ambiophonie est
désactivée; activez-la pour pouvoir l’utiliser.
Activation de la fonction Ambiophonie : Appuyez sur la
touche de la télécommande pendant environ
3 secondes, puis appuyez plusieurs fois sur la
touche pour sélectionner ON - SURROUND
(Ambiophonie activée) dans la fenêtre d’afchage.
Désactivation de la fonction Ambiophonie : Appuyez
sur la touche
de la télécommande pendant
environ 3 secondes, puis appuyez plusieurs fois sur
la touche
pour sélectionner OFF - SURROUND
(Ambiophonie désactivée) dans la fenêtre d’afchage.
Avis d’Industrie Canada
[Pour la fonction sans l (WLAN, Bluetooth, etc.)]
L’émetteur/récepteur exempt de licence contenu dans
le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables
aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
CAN ICES-3 (B)/NMB-3 (B)
Avis d’Industrie Canada sur l’exposition aux
rayonnements
[Pour la fonction sans l (WLAN, Bluetooth, etc.)]
Cet appareil est conforme aux limites d’exposition aux
rayonnements d’Industrie Canada pour un environnement
non contrôlé. Cet appareil doit être installé de façon à garder
une distance minimale de 20 cm (7,8 po) entre la source de
rayonnement et votre corps.
REMARQUE : LE FABRICANT N’EST PAS RESPONSABLE
DES INTERFÉRENCES RADIOÉLECTRIQUES CAUSÉES PAR
DES MODIFICATIONS NON AUTORISÉES APPORTÉES À
CET APPAREIL. DE TELLES MODIFICATIONS POURRAIENT
ANNULER L’AUTORISATION ACCORDÉE À L’UTILISATEUR DE
FAIRE FONCTIONNER L’APPAREIL.
AVERTISSEMENTS
[Pour les produits ayant la fonction sans l utilisant des
bandes de fréquences de 5 GHz]
i. les dispositifs fonctionnant dans la bande de 5 150
à 5 250 MHz sont réservés uniquement pour une
utilisation à l’intérieur an de réduire les risques de
brouillage préjudiciable aux systèmes de satellites
mobiles utilisant les mêmes canaux;
ii. pour les dispositifs munis d’antennes amovibles, le
gain maximal d’antenne permis pour les dispositifs
utilisant les bandes de 5 250 à 5 350 MHz et de
5 470 à 5 725 MHz doit être conforme à la limite
de la p.i.r.e;
iii. pour les dispositifs munis d’antennes amovibles, le
gain maximal d’antenne permis (pour les dispositifs
utilisant la bande de 5 725 à 5 850 MHz) doit être
conforme à la limite de la p.i.r.e. spéciée, selon le
cas;
iv. [pour des dispositifs fonctionnant dans la bande de
5 250 à 5 350 MHz ayant une p.i.r.e. de plus de
200 mW] , les types d’antennes (s’il y en a
plusieurs), les numéros de modèle de l’antenne et
les pires angles d’inclinaison nécessaires pour rester
conforme à l’exigence de la p.i.r.e. applicable au
masque d’élévation, énoncée à la CNR-247
section 6.2.2.3, doivent être clairement indiqués.
Les utilisateurs doivent également savoir que les radars
de grande puissance sont attribués en tant qu’utilisateurs
principaux (c’est-à-dire les utilisateurs prioritaires) des
bandes de 5 250 à 5 350 MHz et de 5 650 à
5 850 MHz et que ces radars peuvent causer des
interférences avec les appareils LE-LAN et/ou les
endommager.
www.lg.com
Copyright © 2020 LG Electronics Inc. Tous droits réservés.2005_Rev02
MFL71672724
MANUEL SIMPLIFIÉ
Ensemble de haut-parleurs
arrière sans l
Veuillez lire attentivement ce manuel avant d’utiliser votre appareil et
conservez-le pour vous y reporter ultérieurement.
Pour voir les instructions relatives aux fonctionnalités avancées, visitez le
http://www.lg.com et téléchargez le guide d’utilisation. Certains éléments de
ce manuel pourraient ne pas correspondre à votre appareil, selon son modèle.
MODÈLE
SPJ4-S
FRANÇAIS
Centre d’information à la clientèle de LG
1-888-542-2623 CANADA
Enregistrez votre produit en ligne!
www.lg.com
Haut-parleur
(gauche)
Récepteur
sans l
Haut-parleur
(droit)
Transparent
Bande noire
Transparent
Bande noire
Téléviseur
Rapprochez au maximum la barre de son
du récepteur sans l, en veillant à conserver
une distance d’au moins 1 m (3,3 pi) de tout
appareil (p. ex. routeur sans l, four à micro-
ondes) an d’éviter les interférences avec les
communications sans l.
> 1 m
(3,3 pi)
SPJ4-S(SN5R).DCANLLK_SIM (Sheet)_MFL71672724.indd 5-8 2020-04-21 3:44:19
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
