Allen-Bradley POINT I/O EtherNet/IP 1734-AENT Installation Instructions Manual

Marque: Allen-Bradley

Modèle: POINT I/O EtherNet/IP 1734-AENT

Taper: Installation Instructions Manual

Ce manuel convient également à

POINT I/O 1734-IE2C

EtherNet is a trademark of Digital Equipment Corporation, Intel, and Xerox Corp.

POINT I/O is a trademark of Rockwell Automation

Publication 1734-IN590A-EN-P - March 2003

Installation Instructions

POINT I/O EtherNet/IP Adapter

(Cat. No. 1734-AENT)

Description Description

1 EtherNet Network RJ45

Connector

5 System Power and Field Power

Indicators

2 Network Address Thumbwheel 6 RTB Removal Handle

3 Indicators - Adapter Status,

PointBus Status, Network

Activity, and Network Status

7 Removable Terminal Block

(RTB)

4 DIN Rail Locking Screw (orange) 8 Safety Endcap

Field

Power

Allen-Bradley

2 POINT I/O EtherNet/IP Adapter

Publication 1734-IN590A-EN-P - March 2003

Important User Information

Because of the variety of uses for the products described in this publication,

those responsible for the application and use of these products must satisfy

themselves that all necessary steps have been taken to assure that each

application and use meets all performance and safety requirements, including

any applicable laws, regulations, codes and standards. In no event will

Rockwell Automation be responsible or liable for indirect or consequential

damage resulting from the use or application of these products.

Any illustrations, charts, sample programs, and layout examples shown in this

publication are intended solely for purposes of example. Since there are many

variables and requirements associated with any particular installation,

Rockwell Automation does not assume responsibility or liability (to include

intellectual property liability) for actual use based upon the examples shown in

this publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application,

Installation and Maintenance of Solid-State Control (available from your local

Rockwell Automation office), describes some important differences between

solid-state equipment and electromechanical devices that should be taken into

consideration when applying products such as those described in this

publication.

Reproduction of the contents of this copyrighted publication, in whole or

part, without written permission of Rockwell Automation, is prohibited.

Throughout this publication, notes may be used to make you aware of safety

considerations. The following annotations and their accompanying statements

help you to identify a potential hazard, avoid a potential hazard, and recognize

the consequences of a potential hazard:

POINT I/O EtherNet/IP Adapter 3

Publication 1734-IN590A-EN-P - March 2003

WARNING

Identifies information about practices or circumstances

that can cause an explosion in a hazardous environment,

which may lead to personal injury or death, property

damage, or economic loss.

ATTENTION

Identifies information about practices or circumstances

that can lead to personal injury or death, property

damage, or economic loss.

IMPORTANT

Identifies information that is critical for successful

application and understanding of the product.

Allen-Bradley

4 POINT I/O EtherNet/IP Adapter

Publication 1734-IN590A-EN-P - March 2003

ATTENTION

Environment and Enclosure

This equipment is intended for use in a Pollution Degree

2 industrial environment, in overvoltage Category II

applications (as defined in IEC publication 60664-1), at

altitudes up to 2000 meters without derating.

This equipment is considered Group 1, Class A industrial

equipment according to IEC/CISPR Publication 11.

Without appropriate precautions, there may be potential

difficulties ensuring electromagnetic compatibility in other

environments due to conducted as well as radiated

disturbance.

This equipment is supplied as "open type" equipment. It

must be mounted within an enclosure that is suitably

designed for those specific environmental conditions that

will be present and appropriately designed to prevent

personal injury resulting from accessibility to live parts.

The interior of the enclosure must be accessible only by

the use of a tool. Subsequent sections of this publication

may contain additional information regarding specific

enclosure type ratings that are required to comply with

certain product safety certifications.

See NEMA Standards publication 250 and IEC

publication 60529, as applicable, for explanations of the

degrees of protection provided by different types of

enclosure. Also, see the appropriate sections in this

publication, as well as the Allen-Bradley publication

1770-4.1 ("Industrial Automation Wiring and Grounding

Guidelines"), for additional installation requirements

pertaining to this equipment.

POINT I/O EtherNet/IP Adapter 5

Publication 1734-IN590A-EN-P - March 2003

ATTENTION

Preventing Electrostatic Discharge

This equipment is sensitive to electrostatic discharge,

which can cause internal damage and affect normal

operation. Follow these guidelines when you handle this

equipment:

• Touch a grounded object to discharge potential

static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component

boards.

• Do not touch circuit components inside the

equipment.

• If available, use a static-safe workstation.

• When not in use, store the equipment in appropriate

static-safe packaging.

ATTENTION

POINT I/O is grounded through the DIN rail to chassis

ground. Use zinc-plated, yellow-chromated steel DIN rail

to assure proper grounding. Using other DIN rail

materials (e.g. aluminum, plastic, etc.) which can corrode,

oxidize or are poor conductors, can result in improper or

intermittent platform grounding.

WARNING

When you connect or disconnect the Removable

Terminal Block (RTB) with field side power applied, an

electrical arc can occur. This could cause an explosion in

hazardous location installations.

Be sure that power is removed or the area is

nonhazardous before proceeding.

Allen-Bradley

6 POINT I/O EtherNet/IP Adapter

Publication 1734-IN590A-EN-P - March 2003

Installing the EtherNet/IP Adapter

To install the adapter on the DIN rail prior to installing other base units,

proceed as follows.

1. Position the adapter vertically above the DIN rail.

2. Press down firmly to install the adapter on the DIN rail. The locking

mechanism will lock the adapter to the DIN rail.

3. Set the node address on the node address thumbwheel.

4. Slide the safety end cap up to remove. This exposes the backplane and

power interconnections.

WARNING

If you connect or disconnect the EtherNet cable with

power applied to this module or any device on the

network, an electrical arc can occur. This could cause an

explosion in hazardous location installations.

Be sure that power is removed or the area is nonhazardous

before proceeding.

ATTENTION

Do not discard the end cap. Use this end cap to cover the

exposed interconnections on the last mounting base on

the DIN rail. Failure to do so could result in equipment

damage or injury from electric shock.

POINT I/O EtherNet/IP Adapter 7

Publication 1734-IN590A-EN-P - March 2003

Setting the Network Address

You can set the network Internet Protocol (IP) address 3 different ways:

1. using the thumbwheel switches located on the module

2. using a Dynamic Host Configuration Protocol (DHCP) server, such

as Rockwell Automation BootP/DHCP

3. retrieving the IP address from nonvolatile memory.

The adapter reads the thumbwheel switches first to determine if the switches

are set to a valid number. You set the node address using the 3-position

thumbwheel switch. Press either the + or - buttons to change the number.

Valid settings range from 001 to 254. When the switches are set to a valid

number, the adapter’s IP address will be 192.168.1.xxx (where xxx represents

the number set on the switches). The adapter’s subnet mask will be

255.255.255.0 and the gateway address is set to 0.0.0.0. The adapter will not

have a host name assigned, or use any Domain Name System when using the

thumbwheel settings.

If the switches are set to an invalid number (i.e. 000 or a value greater than

254), the adapter checks to see if DHCP is enabled. If DHCP is enabled, the

adapter asks for an address from a DHCP server. The DHCP server will also

assign other Transport Control Protocol (TCP) parameters.

If DHCP is not enabled, the adapter will use the IP address (along with other

TCP configurable parameters) stored in nonvolatile memory.

Refer to publication 1734-UM010, POINT I/O EtherNetIP Adapter User

Manual, for more information.

Module

Status

Network

Activity

Network

Status

1734-AENT

PointBus

Status

Field

Power

System

Power

43248

Network Address

Thumbwheel

Press either the + or -

buttons to change the

number.

Allen-Bradley

8 POINT I/O EtherNet/IP Adapter

Publication 1734-IN590A-EN-P - March 2003

Installing a Replacement EtherNet/IP Adapter to an Existing System

1. Remove the existing adapter from the DIN rail as follows:

a. Disconnect the EtherNet connector from the adapter.

b. Pull up on the RTB removal handle to remove the terminal block.

c. Remove the adjacent module from its base.

d. Use a small bladed screwdriver to rotate the DIN rail locking

screw to a vertical position. This releases the locking mechanism.

e. Lift straight up to remove.

2. Slide the safety end cap up to remove. This exposes the backplane and

power connections.

3. Position the replacement adapter vertically above the DIN rail. (Make

certain the DIN rail lock is in the horizontal position.) Slide the

adapter down, allowing the interlocking side pieces to engage the

adjacent module.

4. Press firmly to seat the adapter on the DIN rail. The adapter locking

mechanism will snap into place.

5. Set the node address on the node address thumbwheel.

6. Insert the end of the terminal block (RTB) opposite the handle into

the base unit. This end has a curved section that engages with the

wiring base.

7. Rotate the terminal block into the wiring base until it locks itself into

place.

8. Replace the adjacent module in its base.

9. Reconnect the Ethernet cable to the adapter.

ATTENTION

You must use Series C POINT I/O modules with the

1734-AENT adapter. Series A or B POINT I/O modules

will not work with this adapter.

POINT I/O EtherNet/IP Adapter 9

Publication 1734-IN590A-EN-P - March 2003

Wiring the EtherNet/IP Adapter

43264

System Power

CHAS GND

Node Address

Thumbwheels

Field Power

NC = No Connection

CHAS GND = Chassis Ground

C = Common

V = Supply

Module Status

Network Activity

Network Status

EtherNet RJ-45 Connector

PointBus Status

Module

Status

Network Activity

Status

Network

Status

1734-AENT

PointBus

Status

Field

Power

System

Power

V dc

Chas

Gnd

NC = No Connection C = Common

Chas GND = Chassis Ground V = Supply

Chas

Gnd

Do not connect

120/240V ac power

to this supply.

12/24V dc

This dc supply will be

connected to the internal

power bus.

Allen-Bradley

10 POINT I/O EtherNet/IP Adapter

Publication 1734-IN590A-EN-P - March 2003

Troubleshooting with the Indicators

Indication Probable Cause

System Power

Off Not active; field power is off or dc-dc converter problem

Green System power on; dc-dc converter active (5V)

Field Power

Off Not active; field power is off

Green Power on; 24V present

Indication Probable Cause

Module Status

Off No power applied to device

Flashing Red/Green LED powerup test (module self-test)

Green Device is operating normally

Flashing Red Recoverable fault has occurred:

• Firmware (NVS) update

• Network IP Address changed

• CPU load exceeded

Solid Red Unrecoverable fault has occurred:

• Self-test failure (checksum failure, or ramtest

failure at powerup)

• Firmware fatal error

System Power

Field Power

43248aent

Module Status

Network Activity

Network Status

PointBus Status

Module

Status

Network

Activity

Network

Status

1734-AENT

PointBus

Status

Field

Power

System

Power

POINT I/O EtherNet/IP Adapter 11

Publication 1734-IN590A-EN-P - March 2003

Indication Probable Cause

Network Status

Off Device not initialized. The module does not have an IP

address.

Flashing Green No CIP connections. Device has an IP address, but no CIP

connections are established.

Green CIP connections. Device on-line and has an IP address, and

CIP connections are established.

Flashing Red One or more EtherNet connections has timed-out.

Red No link. The module is not physically connected to a

powered EtherNet Device.

Flashing Red/Green The module is performing a self-test (only occurs during

powerup test).

Network Activity

Off No link established.

Flashing Green/Off Transmit or receive activity.

Steady Green Link established.

PointBus Status

Off Device not powered - check module status indicator.

Flashing Red/Green LED powerup test.

Flashing Red Recoverable fault has occurred:

• at powerup the number of expected modules

does not equal the number of modules present

• a module is missing

• node fault (I/O connection timeout).

Red Unrecoverable fault has occurred:

• the adapter is bus off

• the adapter has failed its duplicate MAC ID check.

Flashing Green Adapter online with no connections established:

• adapter chassis size has not been configured

• controller in program/idle mode

• EtherNet cable open

Green Adapter online with connections established (normal

operation, run mode).

Allen-Bradley

12 POINT I/O EtherNet/IP Adapter

Publication 1734-IN590A-EN-P - March 2003

Safety Approvals

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l’utilisation de cet équipement

en environnements dangereux:

Products marked “CL I, DIV 2, GP A, B, C, D” are

suitable for use in Class I Division 2 Groups A, B,

C, D, Hazardous Locations and nonhazardous

locations only. Each product is supplied with

markings on the rating nameplate indicating the

hazardous location temperature code. When

combining products within a system, the most

adverse temperature code (lowest “T” number)

may be used to help determine the overall

temperature code of the system. Combinations of

equipment in your system are subject to

investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués “CL I, DIV 2, GP A, B, C, D” ne

conviennent qu’à une utilisation en environnements

de Classe I Division 2 Groupes A, B, C, D dangereux et

non dangereux. Chaque produit est livré avec des

marquages sur sa plaque d’identification qui

indiquent le code de température pour les

environnements dangereux. Lorsque plusieurs

produits sont combinés dans un système, le code de

température le plus défavorable (code de température

le plus faible) peut être utilisé pour déterminer le

code de température global du système. Les

combinaisons d’équipements dans le système sont

sujettes à inspection par les autorités locales

qualifiées au moment de l’installation.

EXPLOSION HAZARD -

• Do not disconnect equipment unless

power has been removed or the area

is known to be nonhazardous.

• Do not disconnect connections to

this equipment unless power has

been removed or the area is known

to be nonhazardous. Secure any

external connections that mate to

this equipment by using screws,

sliding latches, threaded

connectors, or other means provided

with this product.

• Substitution of components may

impair suitability for Class I, Division

• If this product contains batteries,

they must only be changed in an

area known to be nonhazardous.

RISQUE D’EXPLOSION –

• Couper le courant ou s’assurer que

l’environnement est classé non

dangereux avant de débrancher

l'équipement.

• Couper le courant ou s'assurer que

l’environnement est classé non

dangereux avant de débrancher les

connecteurs. Fixer tous les connecteurs

externes reliés à cet équipement à

l'aide de vis, loquets coulissants,

connecteurs filetés ou autres moyens

fournis avec ce produit.

• La substitution de composants peut

rendre cet équipement inadapté à une

utilisation en environnement de Classe

1, Division 2.

• S’assurer que l’environnement est

classé non dangereux avant de changer

les piles.

WARNING

AVERTISSEMENT

POINT I/O EtherNet/IP Adapter 13

Publication 1734-IN590A-EN-P - March 2003

Specifications

Specifications - 1734-AENT EtherNet/IP Adapter

Expansion I/O Capacity Maximum of 63 modules

Maximum of 5 Rack Optimized connections (for digital

modules only)

Maximum of 25 direct connections

1734-AENT backplane current output = 1.0A.

The actual number of modules can vary. Add up the

current requirements of the modules you want to use to

make sure they do not exceed the amperage limit of

1.0A for the 1734-AENT.

Backplane current can be extended beyond 1.0A by

using 1734-EP24DC backplane extension Power

Supplies. Add multiple 1734-EP24DC modules to reach

the 63 module maximum).

Cat. No. PointBus Current Requirements

1734-IB2 75mA

1734-IB4 75mA

1734-IV2 75mA

1734-IV4 75mA

1734-OB2E 75mA

1734-OB2EP 75mA

1734-OB4E 75mA

1734-OV2E 75mA

1734-OV4E 75mA

1734-OW2 80mA

1734-OX2 100mA

1734-IE2C 75mA

1734-OE2C 75mA

1734-IE2V 75mA

1734-OE2V 75mA

1734-IA2 75mA

1734-IM2 75mA

1734-OA2 75mA

1734-IJ2 160mA

1734-IK2 160mA

1734-IR2 220mA

1734-IT2I 175mA

1734-SSI 110mA

1734-VHSC5 180mA

1734-VHSC24 180mA

1734-232ASC 75mA

1734-485ASC 75mA

EtherNet Communication

Rate

10/100Mbits/s, half or full-duplex

Module Location Starter module - left side of the 1734 system

Allen-Bradley

14 POINT I/O EtherNet/IP Adapter

Publication 1734-IN590A-EN-P - March 2003

Power Supply Specifications

Input Voltage Rating 24V dc nominal

10-28.8V dc range

Field Side Power

Requirements

24V dc (+20% = 28.8V dc maximum) @ 400mA

maximum

Inrush Current 6A maximum for 10ms

Interruption Output voltage will stay within specifications when

input drops out for 10ms at 10V with maximum load.

General Specifications

Indicators 4 red/green status indicators

Adapter status

PointBus status

Network activity status

Network status

2 green power supply status indicators:

System Power (PointBus 5V power)

Field Power (24V from field supply)

Power Consumption 4.5W maximum @ 28.8V dc

Power Dissipation 15.5W maximum @ 28.8V

PointBus Output Current 1A maximum @ 5V dc ±5% (4.75 - 5.25)

Input Overvoltage

Protection

Reverse polarity protected

Thermal Dissipation 9.5 BTU/hr maximum @ 28.8V dc

Isolation Voltage Tested to withstand 1250V rms for 60s

Field Power Bus

Nominal Voltage

Supply Voltage Range

Supply Current

24V dc

10-28.8V dc range,

10A maximum

Dimensions Inches

(Millimeters)

3.0H x 2.16W x 5.25L

(76.2H x 54.9W x 133.4L)

POINT I/O EtherNet/IP Adapter 15

Publication 1734-IN590A-EN-P - March 2003

Environmental Conditions

Operational

Temperature

IEC 60068-2-1 (Test Ad, Operating Cold),

IEC 60068-2-2 (Test Bd, Operating Dry Heat),

IEC 60068-2-14 (Test Nb, Operating Thermal Shock):

-20 to 55°C (-4 to 131°F)

Storage Temperature IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating

Cold),

IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry

Heat),

IEC 60068-2-14 (Test Na, Unpackaged Nonoperating

Thermal Shock): -40 to 85°C (-40 to 185°F)

Relative Humidity IEC 60068-2-30 (Test Db, Unpackaged Nonoperating

Damp Heat): 5 to 95% noncondensing

Shock IEC 60068-2-27 (Test Ea, Unpackaged Shock)

Operating 30g peak acceleration

Nonoperating 50g peak acceleration

Vibration IEC 60068-2-6 (Test Fc, Operating)

Tested 5g @ 10-500Hz

ESD Immunity IEC 61000-4-2:

4kV contact discharges

8kV air discharges

Radiated RF Immunity IEC 61000-4-3:

10V/m with 1kHz sine-wave 80%AM from 30MHz to

2000MHz

10V/m with 200Hz 50% pulse 100%AM from 900MHz

EFT/B Immunity IEC 61000-4-4:

+4kV at 2.5kHz on power ports

+2kV at 5.0kHz on signal ports

Surge Transient

Immunity

IEC 61000-4-5:

+1kV line-line(DM) and +2kV line-earth(CM) on signal

ports

+1kV line-line(DM) and +2kV line-earth(CM) on power

ports

Conducted RF

Immunity

IEC 61000-4-6:

10Vrms with 1kHz sine-wave 80%AM from 150kHz to

80MHz

Emissions CISPR 11

Group 1, Class A

Enclosure Type Rating None (open-style)

Allen-Bradley

Publication 1734-IN590A-EN-P - March 2003 PN 957726-45

Conductors

Wire Size

Allen-Bradley POINT I/O EtherNet/IP 1734-AENT Installation Instructions Manual

Marque: Allen-Bradley

Modèle: POINT I/O EtherNet/IP 1734-AENT

Taper: Installation Instructions Manual

Ce manuel convient également à

POINT I/O 1734-IE2C

Télécharger le PDF

rapport

dans d''autres langues

English: Allen-Bradley POINT I/O EtherNet/IP 1734-AENT

Allen-Bradley POINT I/O EtherNet/IP 1734-AENT Installation Instructions Manual

Ce manuel convient également à

Allen-Bradley POINT I/O EtherNet/IP 1734-AENT Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents