Elan ELAN gSC2 Mode d'emploi

Marque: Elan

Modèle: ELAN gSC2

Taper: Mode d'emploi

Ce manuel convient également à

gSC2

DC Power

Connection

Serial

Connections

2 bi-directional RS-232 Ports

Sense Input

Connections

2 ELAN Sensor

input Ports

IR Outputs

4 discrete IR channels.

Compatible with Xantech

single and dual emitters.

USB Modem Connections

USB - See Integration Notes for compatible equipment

Ethernet Connection

Ethernet - 10/100 Mbps

PoE IEEE 802.3at Type 2

48 VDC, 600 mA

Relay

Connections

2 Normally Open Relays

12VDC 24VAC @ 1

AMP Compatibility

WIFI Antenna

802.11 b/g/n

Reset

Reset's the

unit's IP address

to factory default

(DHCP).

Press and hold

for programming

reset.

Factory use

ONLY

gSC2

Rear Panel Connections

gSC2

Quick Install Guide

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves or other apparatus

(including ampliﬁers) that produce heat.

9. Only use attachments/accessories speciﬁed

by the manufacturer.

10. Unplug this apparatus during Iightning storms or when

unused for long periods of time.

11. Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

FCC and IC Information:

This Class B digital apparatus complies with Part 15 of the

FCC rules and with Canadian ICES-003 and RSS-210.

Operation is subject to the following two conditions:

1. This device may not cause interference and

2. This device must accept any interference, including

interference that may cause undesired operation

of the device.

Cet appareil numérique de classe B est conforme aux normes

canadiennes ICES-003 et RSS-210. Son fonctionnement est

soumis aux deux conditions suivantes : (1) cet appareil ne doit

pas causer d’interférence et (2) cet appareil doit accepter toute

interférence, notamment les interférences qui peuvent affecter

son fonctionnement.

Warning: Changes or modiﬁcations to this unit not expressly

approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

FCC and IC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment and meets the exemption

from the routine evaluation limits in section 2.5 of RSS 102.

1. This Transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure

limits set forth for an uncontrolled environment.

This equipment should be installed and operated

with a minimum distance of 20 centimeters from user

and bystanders.

Warning: The device meets the exemption from the routine

evaluation limits in section 2.5 of RSS 102, and users can

obtain Canadian information on RF exposure and compliance

from the Canadian Representative Product Solutions Group

at Tel: (519) 763-4538.

Notice: Use only the antenna provided with the product:

R-SMA Antenna, Aristotle Enterprises Inc.

p/n RFA-02-L2M2-M10-N, gain of 2.0 dBi.

English

Important Safety Instructions

, g!

and Panamax

are registered trademarks ofCore Brands,LLC,aNortek company.

P/N 9901333 Rev. E 05 /2014

Dimension: 8-1/2” W x 1-9/16” H x 5” D (half rack) (215.9mm W x 39.69mm H x 127mm D)

This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required

antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type,

are strictly prohibited for use with this device.

Cet émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d’antennes énumérés cidessous avec le gain maximal admissible et impédance

d’antenne requise pour chaque type d’antenne indiqué. Types d’antennes n’est pas inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce type,

sont strictement interdits pour une utilisation avec cet appareil.

Antenna Type Peak Gain

Dipole Antenna 2.09dBi

FEDERAL COMMUNICATIONS COMMISSION

INTERFERENCE STATEMENT:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15

of the FCC Rules.

These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference

by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help.

Informations concernant l’exposition aux fréquences radio (RF):

La puissance de sortie émise par l’appareil de sans ﬁl est inférieure à la limite ‘exposition aux fréquences radio d’Industry Canada (IC). Utilisez l’appareil de sans ﬁl de

façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d’exposition aux

RF d’IC dans des conditions d’exposition à des appareils mobiles (antennes sont supérieures à 20 cm à partir du corps d’une personne).

Mount the gSC2 in the desired location

The gSC2 is designed to mount on a shelf, hang in a cabinet

or rack, or mount in a structured wiring enclosure.

Shelf Mounting:

The gSC2 has rubber feet to protect ﬁnished surfaces.

Set the gSC2 in a location that will allow you to properly

manage connected wiring so that tension is not placed on the

connections. The gSC2 is relatively small and wire tension

will cause the unit to move and may cause wires to become

disconnected.

Dimension: 8-1/2” W x 1-9/16” H x 5” D (half rack)

(215.9mm W x 39.69mm H x 127mm D)

Wall Mounting:

The Wall Mounting Brackets included with the gSC2 attach to the

chassis using the included screws.

Do not use longer screws to attach the brackets as this may

permanently damage the gSC2. Utilizing the Wall Mount Brack-

ets the gSC2 may be mounted in any orientation that suits your

installation.

Using the unit with the attached brackets as a template mark

the keyhole screw locations and the security screw locations.

Pre-drill all holes and insert only the keyholes screws. Hang the

gSC2 on the keyholes screws and then insert the security screws.

Structured Wiring Cabinet Mounting: Mounting the gSC2 in

a structured wiring cabinet is essentially the same as Wall

Mounting it. The difference is that you must supply mounting

screws that are short enough to not penetrate through the wall

behind the enclosure.

To protect your equipment from power surges and momentary power interruptions we strongly

suggest you utilize a battery-backed power supply (UPS) with this equipment.

ELAN recommends Panamax UPS and power conditioning products for use with your new gSC2.

Unpack the gSC2. Verify that you have all packaging contents.

You should have received:

a. gSC2 f. 1ea RJ-45 to serial DB-9

b. 12vDC Power Supply null modem adaptor (P/N 8900599)

c. Wall mounting brackets g. Relay wiring connector

d. Wall mounting hardware h. WiFi antenna

e. 2ea RJ-45 to serial DB9 male adaptors i. Quick Install Guide (this document)

(P/N 8900597)

The g! Training Guide contains valuable hardware and software reference documentation and is considered

an important supplement to this document. You would have received the training guide while attending

g!School, however the g! Training Guide is updated regularly. Make sure you have the latest version by visiting

the ELAN Dealer website at www.elanhomesystems.com and following the “dealer” link.

Note: The gSC2 does not have a ViaNET connection. If your installation has devices that require

ViaNET communication you will need to connect an ELAN SC1 to one of the serial RS-232 ports.

www.elanhomesystems.com

Relay Connections

Two normally open relays are available for controlling

third party devices. The included removable connector will

accept up to 16ga bare copper leads. Be careful to verify

that no portion of one wire touches the other wire. Prior to

connection verify that the connected load does not exceed 24volts

AC/DC or 1amp. If either parameter is exceeded, add a higher

capacity relay to control the load and use the gSC2 output to

control that relay.

Sense Input Connections

ELAN sensors can be used to input a status from 3rd party

devices. The status can either be ON or OFF. This can be used to

trigger an event map or as a condition of an event map. Connect

ONLY ELAN sensors to these ports.

DC Power

Connection

Serial

Connections

2 bi-directional RS-232 Ports

Sense Input

Connections

2 ELAN Sensor

input Ports

IR Outputs

4 discrete IR channels.

Compatible with Xantech

single and dual emitters.

USB Modem Connections

USB - See Integration Notes for compatible equipment

Ethernet Connection

Ethernet - 10/100 Mbps

PoE IEEE 802.3at Type 2

48 VDC, 600 mA

Relay

Connections

2 Normally Open Relays

12VDC 24VAC @ 1

AMP Compatibility

WIFI Antenna

802.11 b/g/n

Reset

Reset's the

unit's IP address

to factory default

(DHCP).

Press and hold

for programming

reset.

Factory use

ONLY

Available ELAN sensors include: AUDIO, VIDEO, CONTACT CLOSURE,

VOLTAGE, LED/LIGHT, and CURRENT/MAGNETIC FIELD sensors.

ELA N HC4/HC8 INSTALLATION MANUAL

Page 24

Sense Input Connections

The Sense Inputs of the HC4 (2) / HC8 (4) are used to conditionally execute macros and to

trigger Event Maps that have been programmed into the System Controller using the ELAN

configuration software.

When used with a conditional macro the sensor is connected to the device being

monitored. The ELAN configuration software can be used to create a macro that checks

the status of the sensor prior to issuing a command. This “conditional pro

gramming” can

be used to prevent a TV, for example, from being inadvertently turned on or off when

changing sources or turning a zone on or off.

Event Maps can be programmed that execute a command or sequence of commands when

a Sense Input is triggered. For example, a driveway sensor can be used to activate an

ELAN contact closure sensor to trigger an Event Map that turns on the outside lights. The

status of a light sensor can be used to make the triggering of the Even

t Map conditional. If

it is daytime the lights don’t come on. If it is nighttime, they do.

The HC4/HC8 provides +5 VDC to the TIP (VSNS) connection to power the Sensor. When

the Sensor is activated, it shorts the ring (SNS) to the sleeve (GND) thereby triggering the

HC4/HC8’s Sense Input. See Figure 3-7.

Figure 3-7: Sense Inputs

Available ELAN sensors include: AUDIO, VIDEO, CONTACT CLOSURE, and VOLTAGE,

LED/LIGHT, and CURRENT/MAGNETIC FIELD sensor

Serial Connections

Connect up to 2 RS-232 serial controlled devices using the

included DB9 to RJ-45 adapters. The gSC2 serial outputs are not

compatible with RS-485 serial devices. If your project requires

RS-485 connections you will need to use a gSC10 controller.

RS-232 wiring pin-outs are as follows:

RS-232 Connections

The table shows the 568A and 568B color codes and the

function of each conductor of the RS-232 ports. Please refer to

the ELAN Integration Note for the speciﬁc device to determine

the proper RJ45 to DB9 adaptor to use.

DC Power

Connection

Serial

Connections

2 bi-directional RS-232 Ports

Sense Input

Connections

2 ELAN Sensor

input Ports

IR Outputs

4 discrete IR channels.

Compatible with Xantech

single and dual emitters.

USB Modem Connections

USB - See Integration Notes for compatible equipment

Ethernet Connection

Ethernet - 10/100 Mbps

PoE IEEE 802.3at Type 2

48 VDC, 600 mA

Relay

Connections

2 Normally Open Relays

12VDC 24VAC @ 1

AMP Compatibility

WIFI Antenna

802.11 b/g/n

Reset

Reset's the

unit's IP address

to factory default

(DHCP).

Press and hold

for programming

reset.

Factory use

ONLY

ELA N

HC4/HC8

INSTALLATION MANUAL

Page 20

RS-232 Connections (Continued)

The table below shows the 568A and 568B color codes and the function of each conductor

of the RS-232 ports. Note that Comm ports one and two use pins two and three for

hardware handshaking. Some 3

party devices require these connections.

See the Integration Notes for the devices you are connecting to determine which Comm

Ports and DB9 to RJ45 adapters are appropriate

RS-232 Port Pin # 568A Color Code 568B Color Code

Function

(Ports 3 +)

1 White/Green White/Orange N/C N/C

2 Green Orange DCD N/C

3 White/Orange White/Green DTR RTS

4 Blue Blue GND GND

5 White/Blue White/Blue RXD RXD

6 Orange Green TXD TXD

7 White/Brown White/Brown CTS CTS

8 Brown Brown RTS RTS

Function

Software upgrade

Prior to conﬁguring the product, upgrade the gSC2 software to

the latest version of g! Core Module. Core Module can be found

on the ELAN dealer website. The gSC2 is not compatible with g!

Core Module releases prior to g!7.0.

Connecting to the gSC2 on your network

The gSC2 is set from the factory for DHCP networking, which

means it receives its IP address from the network router.

Use g!Tools to ﬁnd the address and connect to the gSC2.

TEST

The TEST connection is for factory and repair access only.

Do not plug anything into the TEST port. Plugging anything into

the TEST port will void the warranty and release the magic smoke.

Power Connection

Once all other connections have been completed, connect the

supplied 12VDC power supply and engage the power switch on

the front of the gSC2.

RESET Switch

When pressed momentarily the RESET switch will clear the static IP setup and return the gSC2 to

DHCP as well as reset the WiFi conﬁguration to factory default. When pressed and

held for more than 15 seconds the programming of the current version will be reset to

default. Pressing RESET while applying power will reset the software to the factory version.

WARNING! THIS CANNOT BE UNDONE!!!

USB connection

Some accessories may be connected to the gSC2’s USB

connector. Refer to the ELAN Integration Note for the device prior

to connection.

Ethernet Connection

Connect the Ethernet connection to an available 10/100 Mbps

port on the network. This is the preferred connection.

The gSC2 may be powered over Ethernet (PoE). PoE connection

must meet IEEE 802.3at Type 2 requirements of up to 25W

(@50VDC 600mA max).

WiFi Antenna

The gSC2 includes a WiFi radio for installations where

a hardwired Ethernet connection is not available. This ﬂexibility

allows the gSC2 to be used as both an primary

controller and to act as an extender when necessary. Ethernet

connection is preferred, and should always be used when

available. The WiFi radio should be used sparingly and only in

Extender Mode. The antenna connector is a standard R SMA type

connector. Use only antennas provided with the equipment

or as listed on page 2 of this document. Conﬁguring the WiFi

radio may only be accomplished while the gSC2 is connected to

an Ethernet connection and is covered in the g! Conﬁgurator

reference guide.

IR Output Connections

Four discrete IR outputs are supplied to control third party devices.

The outputs may be conﬁgured in g! programming to utilize a

carrier or not. Each output is compatible with Xantech single and

dual emitters.

DC Power

Connection

Serial

Connections

2 bi-directional RS-232 Ports

Sense Input

Connections

2 ELAN Sensor

input Ports

IR Outputs

4 discrete IR channels.

Compatible with Xantech

single and dual emitters.

USB Modem Connections

USB - See Integration Notes for compatible equipment

Ethernet Connection

Ethernet - 10/100 Mbps

PoE IEEE 802.3at Type 2

48 VDC, 600 mA

Relay

Connections

2 Normally Open Relays

12VDC 24VAC @ 1

AMP Compatibility

WIFI Antenna

802.11 b/g/n

Reset

Reset's the

unit's IP address

to factory default

(DHCP).

Press and hold

for programming

reset.

Factory use

ONLY

Use only with the cart, stand, tripod, bracket or table speciﬁed by the manufacturer or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Elan ELAN gSC2 Mode d'emploi

Marque: Elan

Modèle: ELAN gSC2

Taper: Mode d'emploi

Ce manuel convient également à

gSC2

Télécharger le PDF

rapport

dans d''autres langues

English: Elan ELAN gSC2 User guide

Elan ELAN gSC2 Mode d'emploi

Ce manuel convient également à

Elan ELAN gSC2 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents