Generac 20 kW G0055060 Manuel utilisateur

Marque: Generac

Modèle: 20 kW G0055060

Taper: Manuel utilisateur

TECHNICAL

MANUAL

This manual should remain with the unit.

RTSS Load Shed Automatic Transfer Switch

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all-inclusive. If

using a procedure, work method or operating technique the manu-

facturer does not specifically recommend, ensure that it is safe for

others. Also make sure the procedure, work method or operating

technique chosen does not render the transfer switch unsafe.

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

operation that may be hazardous if performed incorrectly or care-

lessly. Observe them carefully. Their definitions are as follows:

DANGER

After this heading, read instructions that, if not

strictly complied with, will result in personal

injury, including without limitation, death, or

property damage.

After this heading, read instructions that, if not

strictly complied with, may result in personal

injury or property damage.

After this heading, read instructions that, if not

strictly complied with, could result in damage

to equipment and/or property.

NOTE:

After this heading, read explanatory statements that require

special emphasis.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the service are essential to prevent-

ing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates follows:



This symbol points out important safety infor-

mation that, if not followed, could endanger

personal safety and/or property.



This symbol points out potential explosion

hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical

shock hazard.



GENERAL HAZARDS



Any AC generator that is used for backup power if a NORMAL •

(UTILITY) power source failure occurs, must be isolated from

the NORMAL (UTILITY) power source by means of an approved

transfer switch. Failure to properly isolate the NORMAL and

STANDBY power sources from each other may result in injury

or death to electric utility workers, due to backfeed of electrical

energy.

Improper or unauthorized installation, operation, service or •

repair of the equipment is extremely dangerous and may result

in death, serious personal injury, or damage to equipment and/

or personal property.

Extremely high and dangerous power voltages are present inside •

an installed transfer switch. Any contact with high voltage ter-

minals, contacts or wires will result in extremely hazardous,

and possibly LETHAL, electric shock. DO NOT WORK ON THE

TRANSFER SWITCH UNTIL ALL POWER VOLTAGE SUPPLIES

TO THE SWITCH HAVE BEEN POSITIVELY TURNED OFF.

Competent, qualified personnel should install, operate and ser-•

vice this equipment. Adhere strictly to local, state and national

electrical and building codes. When using this equipment,

comply with regulations the National Electrical Code (NEC),

CSA Standard; C22.1 Canadian Electric Code and Occupational

Safety and Health Administration (OSHA) have established.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be fol-

lowed during installation and maintenance of the generator and batteries.

SAVE THESE INSTRUCTIONS! Read the following information carefully before attempting to

install, operate or service this equipment. Also read the instructions and information on tags,

decals, and labels that may be affixed to the transfer switch. Replace any decal or label that is no

longer legible.

DANGER! Connection of a generator to an electrical system normally supplied by an electric

utility shall be by means of suitable transfer equipment so as to isolate the electric system

from utility distribution system when the generator is operating (Article 701 Legally Required

Standby Systems or Article 702 Optional Standby Systems, as applicable). Failure to isolate

electric system by these means may result in damage to generator and may result in injury or

death to utility workers due to backfeed of electrical energy.



Table of Contents

Safety Rules .................................................Inside Front Cover

Section 1 — General Information ............................................ 2

1.1 Introduction ................................................................................ 2

1.2 Equipment Description ................................................................ 2

1.2.1 Transfer Switch Mechanism .............................................. 2

1.2.2 Utility Service Disconnect Circuit Breaker .......................... 2

1.2.3 Load Shed Controller ........................................................ 3

1.2.4 Battery Charger ................................................................ 3

1.3 Transfer Switch Data Decal ......................................................... 3

1.4 Transfer Switch Enclosure ........................................................... 3

1.5 Safe Use Of Transfer Switch........................................................ 3

Section 2 — Installation .......................................................... 4

2.1 Introduction to Installation ........................................................... 4

2.2 Unpacking .................................................................................. 4

2.3 Mounting .................................................................................... 4

2.4 Connecting Power Source and Load Lines .................................. 4

2.5 Neutral Connections .................................................................... 5

2.6 Connecting Control Wires ........................................................... 5

Section 3 — Operation ............................................................ 5

3.1 Functional Tests & Adjustments .................................................. 5

3.2 Manual Operation ........................................................................ 5

3.2.1 ATS Manual Operation ...................................................... 5

3.2.2 LSS Manual Operation ...................................................... 5

3.2.3 Close to Utility Source Side ............................................... 6

3.2.4 Close to Generator Source Side ........................................ 6

3.2.5 Return to Utility Source Side .............................................6

3.3 Voltage Checks ...........................................................................6

3.4 Generator Tests Under Load ........................................................ 7

3.4.1 ATS & Critical Loads ......................................................... 7

3.4.2 Load Shed Functional Test ................................................ 8

Section 4 – Notes .................................................................... 9

Section 5 – Installation Diagrams ......................................... 11

Section 6 – Electrical Data ....................................................14

Section 7 – Exploded Views & Parts Lists ............................. 18

Section 8 – Warranty ............................................... Back Cover

Never handle any kind of electrical device while standing •

in water, while barefoot, or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

Jewelry conducts electricity and wearing it may cause dan-•

gerous electrical shock. Remove all jewelry (such as rings,

watches, bracelets, etc.) before working on this equipment.

If work must be done on this equipment while standing on metal •

or concrete, place insulative mats over a dry wood platform.

Work on this equipment only while standing on such insulative

mats.

Never work on this equipment while physically or mentally •

fatigued.

Keep the transfer switch enclosure door closed and bolted at all •

times. Only qualified personnel should be permitted access to

the switch interior.

In case of an accident caused by electric shock, immediately •

shut down the source of electrical power. If this is not possible,

attempt to free the victim from the live conductor but AVOID

DIRECT CONTACT WITH THE VICTIM. Use a nonconducting

implement, such as a dry rope or board, to free the victim from

the live conductor. If the victim is unconscious, apply first aid

and get immediate medical help.

When an automatic transfer switch is installed for a standby •

generator set, the generator engine may crank and start at

any time without warning. To avoid possible injury that might

be caused by such sudden start-ups, the system’s automatic

start circuit must be disabled before working on or around

the generator or transfer switch. For that purpose, a SAFETY

DISCONNECT is provided inside the transfer switch. Always

set that switch to its OFF position before working on the equip-

ment. Then place a “DO NOT OPERATE” tag on the transfer

switch and on the generator. Remove the Negative (Neg) or (–)

battery cable.

For authorized service, reference

the dealer locator number found

in the generator owner’s manual or

on the generator's data label.

Section 1 — General Information

RTSS Type Transfer Switch

1.1 INTRODUCTION

This manual has been prepared especially for the purpose of famil-

iarizing personnel with the design, application, installation, opera-

tion and servicing of the applicable equipment. Read the manual

carefully and comply with all instructions. This will help to prevent

accidents or damage to equipment that might otherwise be caused

by carelessness, incorrect application, or improper procedures.

Every effort has been expended to make sure that the contents

of this manual are both accurate and current. The manufacturer,

however, reserves the right to change, alter or otherwise improve

the product at any time without prior notice.

1.2 EQUIPMENT DESCRIPTION

The PowerManager™ LTS transfer switch will provide three major

functions.

The first function is to provide an automatic transfer switch.

The automatic transfer switch is used for transferring electrical

loads from a UTILITY (NORMAL) power source to a GENERATOR

(STANDBY) power source. Such a transfer of electrical loads

occurs automatically when (connected to a Generac engine gen-

erator) the UTILITY power source has failed or is at a substantially

reduced voltage and the GENERATOR source voltage and frequen-

cy have reached an acceptable level. The transfer switch prevents

electrical feedback between two different power sources (such as

the UTILITY and GENERATOR sources) and, for that reason, codes

require it in all standby electrical system installations.

The second function is to provide a means to divide up the electri-

cal loads on the electrical system. The electrical loads are to be

divided into “critical loads” and non-essential loads. The “critical”

loads are connected to the internal 16 circuit panel board. The

non-essential electrical loads are to be powered from the load shed

switch (LSS).

The UTILITY source will supply all electrical loads at all times.

When the transfer signal is given by the engine generator controller,

all loads, both critical and non-essential loads, are connected to

the GENERATOR supply. If the generator is overloaded the LSS will

operate and disconnect the non-essential loads which results in a

reduction in the load on the generator.

The third function is a 16 circuit load center to connect the “criti-

cal loads” to. These loads will be normally powered by the UTILITY

source and will be backed up by the GENERATOR source. The

Siemens load center is provided with the following Siemens type

QP circuit breakers; 1-50A 2-pole, 1-40A 2-pole, 1-20A 2-pole,

5-20A single pole and 5-15A 2-pole circuit breakers.

The PowerManager LTS transfer switch is suitable for use as

SERVICE ENTRANCE EQUIPMENT – UTILITY (NORMAL) source

only. The PowerManager LTS is only SERVICE ENTRANCE rated for

the USA. The 200A 2-pole circuit breaker provided is the “service

disconnect” and is labeled as such. An additional disconnect must

be readily available for the alternate source, unless the alternate

source is an accessible generator and can be shutdown.

1.2.1 TRANSFER SWITCH MECHANISM 

These switches (Figure 1.1) are used with a single-phase system,

when the single-phase NEUTRAL line is to be connected to a

Neutral Lug and is not to be switched.

Solderless, screw-type terminal lugs are standard.

Switch

Rating

Wire

Range

Conductor Tightening

Torque

200A #6-250 MCM 275 in-lbs.

This transfer switch is suitable for control of motors, electric dis-

charge lamps, tungsten filament and electric heating equipment

where the sum of motor full load ampere ratings and the ampere

ratings of other loads do not exceed the ampere rating of the

switch and the tungsten load does not exceed 30 percent of the

switch rating.

Figure 1.1 — Typical ATS Transfer Mechanism

UTILITY

CLOSING

COIL

GENERATOR

CLOSING

COIL

UTILITY LUGS

GENERATOR

LUGS (E1 & E2)

LOAD LUGS (T1 & T2)

This transfer switch is for use in optional standby systems only

(NEC

Article 702).

This transfer switch is suitable for use on a circuit capable of

22,000 rms symmetrical amperes, 240 VAC maximum.

1.2.2 UTILITY SERVICE DISCONNECT CIRCUIT 

BREAKER

The utility service disconnect circuit breaker for the 200 amp

models are:

Generac, Type 225AF, 2-pole•

120/240VAC, 200A•

50/60 Hertz•

Wire range: 300 MCM - 6 STR (Line), 250 MCM - 6 STR •

(Load)

The conductor tightening torque is 375 in-lbs. (Line), 275 in-•

lbs. (Non-essential Load and Generator Terminals)

1.2.3 LOAD SHED CONTROLLER 

The primary function of the Load Shed Controller (LSC) is to deter-

mine when there is excess load on the generator and has the ability

to disconnect the non-essential loads connected to it. Excess load

is determined by monitoring the generator supply frequency, if the

frequency drops below 58 Hz for more than three (3) seconds,

or below 50 Hz for 1/2 second, and the generator is considered

to have excess load on it. When this happens, non-essential

customer loads are disconnected. The non-essential loads are

supplied via the load shed switch (LSS) and the LSS is actuated to

disconnect these loads.

The non-essential loads are reconnected in one of 3 ways; Utility

voltage is restored and ATS transfers all load back to the Utility

supply, manual operation of LOAD SHED RESET push-button on

the outside of the enclosure or, automatic operation setup on the

DIP switches on the LSC.

For manual operation, set DIP switch #6 to the ON position. If

the generator output is overloaded and the non-essential loads

are disconnected, press the LOAD SHED RESET push-button to

reconnect the non-essential loads to the generator. If the overload

condition still exists the LSC will turn the non-essential loads off.

For automatic operation, the number of attempts to reconnect the

non-essential loads can be selected. The 2 choices are one-shot

or repeated. The time interval before each attempt is set on DIP

switches 1-4. For “one-shot” operation mode set DIP switch #5 to

ON. Reconnection of the non-essential loads will occur one time,

after the time set on DIP switches 1-4. If DIP switch #5 is OFF,

the LSC will attempt to reconnect the non-essential loads after the

time interval set on DIP switches 1-4. If the overload still exists or

comes back, the LSC and LSS will disconnect non-essential loads

and the timer and the attempt to reconnect non-essential loads

will be repeated.

DIP switch num-

ber

Function

1 Selects a 5 minute reconnection time

2 Selects a 15 minute reconnection time

3 Selects a 30 minute reconnection time

4 Selects a 60 minute reconnection time

1-4 all OFF Selects a 1 minute reconnection time

5 Selects one-shot mode

6 Selects manual reconnect only

7 Selects 50 Hz units

8 Not used

1.2.4 BATTERY CHARGER 

The POWER MANAGER LTS transfer switch is provided with a bat-

tery charger (item #44 on Generac #0G8054 assembly drawing)

for charging of the engine generator 12 Vdc battery. The battery

charger is powered from the load side of the transfer switch (line

to neutral – 120V) and is protected by a 2A fuse on the LSC pcb.

The battery charger will charge the battery at all times.

1.3 TRANSFER SWITCH DATA

DECAL

A DATA DECAL is permanently affixed to the transfer switch enclo-

sure. Use this transfer switch only with the specific limits shown

on the DATA DECAL and on other decals and labels that may be

affixed to the switch. This will prevent damage to equipment and

property.

When requesting information or ordering parts for this equipment,

make sure to include all information from the DATA DECAL.

Record the Model and Serial numbers in the space provided below

for future reference.

MODEL #

SERIAL #

1.4 TRANSFER SWITCH

ENCLOSURE

The standard switch enclosure is a National Electrical Manufacturer’s

Association (NEMA) 3R, UL listed. NEMA 3R type enclosures pri-

marily provide a degree of protection against falling rain and sleet

and is undamaged by the formation of ice on the enclosure.

1.5 SAFE USE OF TRANSFER

SWITCH

Before installing, operating or servicing this equipment, read the

SAFETY RULES (inside front cover) carefully. Comply strictly

with all SAFETY RULES to prevent accidents and/or damage to

the equipment. The manufacturer recommends that a copy of the

SAFETY RULES are posted near the transfer switch. Also, be sure

to read all instructions and information found on tags, labels and

decals affixed to the equipment.

Three publications that outline the safe use of transfer switches

are the following:

NFPA 70; National Electrical Code•

NFPA 70E; Standard for Electrical Safety in the Workplace•

UL 1008, STANDARD FOR SAFETY-AUTOMATIC TRANSFER •

SWITCHES

NOTE:

It is essential to use the latest version of any standard to ensure

correct and current information.

Section 1 — General Information

RTSS Type Transfer Switch

Section 2 — Installation

RTSS Type Transfer Switch

2.1 INTRODUCTION TO

INSTALLATION

This equipment has been wired and tested at the factory. Installing

the switch includes the following procedures:

Mounting the enclosure.•

Connecting power source and load leads.•

Connecting non-essential loads.•

Connecting "Critical Load" branch circuits to the internal load •

center.

Connecting the utility sensing and transfer relay circuits to the •

generator control panel.

Connecting any auxiliary contact (if needed)•

Testing functions.•

2.2 UNPACKING

Carefully unpack the transfer switch. Inspect closely for any dam-

age that might have occurred during shipment. The purchaser

must file with the carrier any claims for loss or damage incurred

while in transit.

Check that all packing material is completely removed from the

switch prior to installation.

2.3 MOUNTING

Mounting dimensions for the transfer switch enclosure are in this

manual. Enclosures are typically wall-mounted. See “Installation

Diagram”.



Handle transfer switches carefully when

installing. Do not drop the switch. Protect

the switch against impact at all times, and

against construction grit and metal chips.

Never install a transfer switch that has been

damaged.

This transfer switch is mounted in a NEMA 3R aluminum enclo-

sure. It can be mounted outside or inside and should be based on

the layout of installation, convenience and proximity to the utility

supply and load center.

Install the transfer switch as close as possible to the electrical

loads that are to be connected to it. Mount the switch vertically to

a rigid supporting structure. To prevent switch distortion, level all

mounting points. If necessary, use washers behind mounting holes

to level the unit.

2.4 CONNECTING POWER SOURCE

AND LOAD LINES

DANGER



Make sure to turn OFF both the UTILITY

(NORMAL) and GENERATOR (STANDBY)

power supplies before trying to connect

power source and load lines to the transfer

switch. Supply voltages are extremely high

and dangerous. Contact with such high volt-

age power supply lines causes extremely haz-

ardous, possibly lethal, electrical shock.

Wiring diagrams and electrical schematics are provided in this

manual.

NOTE:

All installations must comply with national, state and local

codes. It is the responsibility of the installer to perform an

installation that will pass the final electrical inspection.

Conductor sizes must be adequate to handle the maximum cur-

rent to which they will be subjected, based on the 75°C column of

tables, charts, etc. used to size conductors. The installation must

comply fully with all applicable codes, standards and regulations.

Before connecting wiring cables to terminals, remove any surface

oxides from the cable ends with a wire brush. All power cables

must enter the enclosure through the knockouts provided. This

is necessary to maintain the NEMA/UL type 3 rating. If mounted

indoors, conduits can enter the enclosure above the knockouts. If

not using the knockouts, entry must be at or below knockouts.

If ALUMINUM conductors are used, apply corrosion inhibitor to

conductors. Tighten terminal lugs to the torque values as noted on

the "Utility Service Disconnect Circuit Breaker", and on the decal

located on the inside of the door. After tightening terminal lugs,

carefully wipe away any excess corrosion inhibitor.



Use a torque wrench to tighten the conduc-

tors, being sure not to overtighten, or dam-

age to the insulating base could occur. If not

tightened enough, a loose connection would

result, causing excess heat which could dam-

age the switch base.

Connect power source load conductors to clearly marked transfer

mechanism terminal lugs as follows

1. Connect UTILITY (NORMAL) power source cables to the top

of the UTILITY SERVICE DISCONNECT circuit breaker.

2. Connect GENERATOR (STANDBY) source power cables to

ATS GENERATOR supply terminals, E1-E2.

3. Connect non-essential customer LOAD leads to LSS switch

terminals E1, E2.

4. Connect critical customer loads to the circuit breakers on the

load center provided.

Conductors must be properly supported, of approved insulative

qualities, protected by approved conduit, and of the correct wire

gauge size in accordance with applicable codes.

Be sure to maintain proper electrical clearance between live metal

parts and grounded metal. Allow at least 1/2 inch for 100-400

amp circuits.

2.5 NEUTRAL CONNECTIONS

The main neutral block is provided for the connection of the

neutral (ungrounded conductors) of the Utility, Generator and non-

essential load neutrals. Tighten all wires to the specified torque.

Torque values are given on the information decal located on the

inside cover.

The main neutral block is connected (bonded) to the enclosure

metal by a busbar. If bonding of the neutral is not necessary, the

jumper can be removed. When the jumper bar is removed the

control wires should be connected as follows:

#00 wire to the neutral block.•

GRD wire to the enclosure.•

The essential load neutrals are to be connected on the busbars

mounted on the load center, next to the branch circuit breakers.

2.6 CONNECTING CONTROL

WIRES

Control system interconnections consist of N1 and N2, and leads

0, 15B and 23. Control system interconnection leads can be run in

the same conduit as the AC power lead if the conduit length is less

than 35 feet, and ALL of the wiring is rated for 600V. If the conduit

length between the generator and PowerManager LTS is more than

35 feet, the control and power leads must be routed in separate

conduits. Recommended wire gauge sizes for this wiring depends

on the length of the wire, as recommended in the following chart:

MAXIMUM WIRE

RUN LENGTH

RECOMMENDED WIRE

SIZE

35 feet (10.67m) No. 16 AWG.

60 feet (18.29m) No. 14 AWG.

90 feet (27.43m) No. 12 AWG.

3.1 FUNCTIONAL TESTS AND

ADJUSTMENTS

Following transfer switch installation and interconnection,

inspect the entire installation carefully. A competent, qualified

electrician should inspect it. The installation should comply

strictly with all applicable codes, standards, and regulations.

When absolutely certain the installation is proper and correct,

complete a functional test of the system.



Perform functional tests in the exact order

presented in this manual, or damage could be

done to the switch.

IMPORTANT: Before proceeding with functional tests, read and

make sure all instructions and information in this section are

understood. Also read the information and instructions of labels

and decals affixed to the switch. Note any options or accessories

that might be installed and review their operation.

3.2 MANUAL OPERATION

DANGER



Do NOT manually transfer under load.

Disconnect transfer switch from all power

sources by approved means, such as the

main circuit breaker(s).

3.2.1 ATS MANUAL OPERATION 

A manual HANDLE is shipped with the transfer switch. Manual

operation must be checked BEFORE the transfer switch is oper-

ated electrically. To check manual operation, proceed as follows

(Figure 3.1):

1. Turn the generator’s AUTO/OFF/MANUAL switch to OFF.

2. Turn OFF UTILITY SERVICE DISCONNECT circuit breaker.

3. Note position of transfer mechanism main contacts by

observing the moveable contact carrier arm. This can be

viewed through the long narrow slot in the inside cover of the

ATS. The top of the moveable contact carrier arm is yellow to

be easily identified.

Manual operation handle in the UP position - LOAD terminals •

(T1, T2) are connected to UTILITY terminals (N1, N2).

Manual operation handle in the DOWN position - LOAD termi-•

nals (T1, T2) are connected to EMERGENCY terminals (E1,

E2).

3.2.2 LSS MANUAL OPERATION 

A manual HANDLE is shipped with the transfer switch. Manual

operation must be checked BEFORE the LSS is operated electrical-

ly. To check manual operation, proceed as follows (Figure 3.2):

1. Turn the generator’s AUTO/OFF/MANUAL switch to OFF.

2. Turn OFF UTILITY SERVICE DISCONNECT circuit breaker.

3. Note position of non-essential LSS main contacts by observ-

ing the moveable contact carrier arm. This can be viewed

through the long narrow slot in the inside cover of the ATS.

The top of the moveable contact carrier arm is yellow to be

easily identified.

Manual operation handle in the UP position - non-essential •

loads OFF.

Manual operation handle in the DOWN position - non-essen-•

tial loads ON.

Section 3 — Operation

RTSS Type Transfer Switch



Do not use excessive force when operating

the transfer switch manually or damage could

be done to the manual handle.

3.2.3 CLOSE TO UTILITY SOURCE SIDE 

Before proceeding, verify the position of the switch by observing

the position of manual operation handle in Figure 3.1. If the handle

is UP, the contacts are closed in the UTILITY (NORMAL) position,

no further action is required. If the handle is DOWN, proceed with

Step 1.

Step 1: With the handle inserted into the moveable contact carrier

arm, move handle UP. Be sure to hold on to the handle as

it will move quickly after the center of travel.

Step 2: Remove manual operating handle from moveable contact

carrier arm. Return handle to storage bracket.

3.2.4 CLOSE TO GENERATOR SOURCE SIDE 

Before proceeding, verify the position of the switch by observ-

ing the position of the manual operation handle in Figure 3.1. If

the handle is DOWN, the contacts are closed in the GENERATOR

(STANDBY) position. No further action is required. If the handle is

UP, proceed with Step 1.

Step 1: With the handle inserted into the moveable contact carrier

arm, move the handle DOWN. Be sure to hold on to the

handle as it will move quickly after the center of travel.

Step 2: Remove manual operating handle from moveable contact

carrier arm. Return handle to storage bracket.

3.2.5 RETURN TO UTILITY SOURCE SIDE 

Step 1: Manually actuate switch to return manual operating handle

to the UP position.

Step 2: Remove manual operating handle from moveable contact

carrier arm. Return handle to storage bracket.

3.3 VOLTAGE CHECKS

1. Turn ON the UTILITY power supply to the PowerManager LTS

using the UTILITY SERVICE DISCONNECT circuit breaker.

DANGER



PROCEED WITH CAUTION. THE TRANSFER

SWITCH IS NOW ELECTRICALLY HOT.

CONTACT WITH LIVE TERMINALS RESULTS

IN EXTREMELY HAZARDOUS AND POSSIBLY

FATAL ELECTRICAL SHOCK.

2. With an accurate AC voltmeter, check for correct voltage.

Measure across ATS terminal lugs N1 and N2. Also check N1

to NEUTRAL and N2 to NEUTRAL.

3. When certain that UTILITY supply voltage is correct and compat-

ible with transfer switch ratings, turn OFF the UTILITY supply to

the transfer switch.

4. On the generator panel, set the AUTO/OFF/ MANUAL switch to

MANUAL position. The generator should crank and start.

Section 3 — Operation

RTSS Type Transfer Switch

Move handle UP for the

UTILITY (NORMAL) position.

Move handle DOWN for the

GENERATOR (STANDBY) position.

Attach handle to the moveable

contact carrier arm.

NOTE: Return handle to storage position in enclosure when finished with manual transfer.

Figure 3.1 — Actuating ATS Transfer Switch

The voltage measurements should be as follows:

N1 - N2 240 VAC Nominal

N1 - Neutral 120 VAC Nominal

N2 - Neutral 120 VAC Nominal

5. Let the generator stabilize and warm up at no-load for at least

five minutes.

6. Set the generator's main circuit breaker (CB1) to its ON or

CLOSED position.

DANGER



PROCEED WITH CAUTION. GENERATOR

OUTPUT VOLTAGE IS NOW BEING DELIVERED

TO TRANSFER SWITCH TERMINALS.

CONTACT WITH LIVE TERMINALS RESULTS

IN EXTREMELY DANGEROUS AND POSSIBLY

FATAL ELECTRICAL SHOCK.

7. With an accurate AC voltmeter and frequency meter, check the

no-load, voltage and frequency.

Measure across ATS terminal lugs E1 to E2. Also check E1 to

NEUTRAL and E2 to NEUTRAL.

a. Frequency ....................................................60-62 Hertz

b. Terminals E1 to E2 .......................................240-246 VAC

c. Terminals E1 to NEUTRAL ............................120-123 VAC

d. Terminals E2 to NEUTRAL ............................120-123 VAC

8. Set the generator’s main circuit breaker (CB1) to its OFF or

OPEN position.

9. Set the AUTO/OFF/MANUAL switch to the OFF position to shut

down the generator.

NOTE:

Do NOT proceed until generator AC output voltage and fre-

quency are correct and within stated limits. If the no-load volt-

age is correct but no-load frequency is incorrect, the engine

governed speed may require adjustment. If no-load frequency

is correct but voltage is not, the voltage regulator may require

adjustment.

3.4 GENERATOR TESTS UNDER

LOAD

3.4.1 ATS & CRITICAL LOADS 

1. Set the generator's main circuit breaker to its OFF or OPEN

position.

2. Set the UTILITY SERVICE DISCONNECT circuit breaker to the

OFF position.

3. Manually actuate the transfer switch main contacts to

their GENERATOR (STANDBY) position. Refer to "Manual

Operation".

4. Manually actuate the LSS main contacts to the UP position.

Non-essential loads OFF.

5. To start the generator, set the AUTO/OFF/ MANUAL switch to

MANUAL. When engine starts, let it stabilize for a few min-

utes.

Section 3 — Operation

RTSS Type Transfer Switch

Move handle UP for the

non-essential loads OFF.

Move handle DOWN for the

non-essential loads ON.

Attach handle to the moveable

contact carrier arm.

NOTE: Return handle to storage position in enclosure when finished with manual transfer.

Figure 3.2 — Actuating LSS Transfer Switch

6. Turn the generator's main circuit breaker to its ON or CLOSED

position. The generator now powers all LOAD circuits. Check

generator operation under load as follows:

Turn ON electrical loads to the full rated wattage/amperage •

capacity of the generator. DO NOT OVERLOAD.

With maximum rated load applied, check voltage and fre-•

quency across transfer switch terminals E1 and E2. Voltage

should be greater than 230VAC and frequency should be

greater than 59 Hertz.

Let the generator run under rated load for at least 30 minutes. •

With unit running, listen for unusual noises, vibration, over-

heating, etc., that might indicate a problem.

7. When checkout under load is complete, set main circuit

breaker of the generator to its OFF or OPEN position.

8. Let the generator run at no-load for several minutes. Then,

shut down by setting the AUTO/OFF/MANUAL switch to its

OFF position.

9. Move the switch's main contacts back to their UTILITY posi-

tion. For example, LOAD connected to UTILITY power supply.

Refer to "Manual Operation". Handle and operating lever of

transfer switch should be in UP position.

10. Turn on the UTILITY power supply to transfer switch, using

the UTILITY SERVICE DISCONNECT circuit breaker. The utility

power source now powers the loads.

11. Set the generator's AUTO/OFF/MANUAL switch to its AUTO

position.

3.4.2 LOAD SHED FUNCTIONAL TEST 

1. Set the generator’s main circuit breaker to its OFF or OPEN

position.

2. Set the UTILITY SERVICE DISCONNECT circuit breaker to the

OFF position.

3. Manually actuate the transfer switch main contacts to the

GENERATOR position. Refer to “Manual Operation” section of

this manual.

4. Manually actuate the LSS main contacts to the DOWN posi-

tion. Non-essential loads ON.

5. To start the generator, set the AUTO/OFF/MANUAL switch to

MANUAL. When engine starts, let it stabilize for a few min-

utes.

6. Turn the generator’s main circuit breaker its ON position. The

generator now powers all LOAD circuits. Check generator

operation under load as follows:

Turn ON electrical loads to the full rated wattage/amperage •

capacity of the generator.

Increase the load to slightly overload the generator (load to •

draw frequency down 55-56 hz). This will require turning

loads on that are connected to the LSS. Do not severely

overload the generator.

The LSS should actuate after three (3) seconds to disconnect •

the non-essential loads. The door mounted LOAD SHED LED

should be ON.

Decrease the electrical load on the generator to allow the •

generator frequency to increase to 60 Hz.

7. The next step will depend on how the LSC is set up (see the

"Load Shed Controller" section). If set up for:

Manual Operation• — Press the door mounted LOAD SHED

RESET button. The LSS will reconnect non-essential loads.

Automatic Operation• — The LSS will reconnect non-essen-

tial loads after the delay time setup on the DIP switches of

the LSC.

8. Turn ON the UTILITY power supply to the transfer switch using

the UTILITY SERVICE DISCONNECT circuit breaker. After the

return to utility time delay, the utility power source will power

the loads.

9. Set the generator's AUTO/OFF/MANUAL switch to the AUTO

position.

Section 3 — Operation

RTSS Type Transfer Switch

Section 4 — Notes

Section 5 — Installation Diagrams

RTSS Type Transfer Switch

200 Amp Load Shed Enclosure - Drawing No. 0G8775-B

Section 5 — Installation Diagrams

RTSS Type Transfer Switch

Load Shed Interconnection - Drawing No. 0G8774-C

Section 5 — Installation Diagrams

RTSS Type Transfer Switch

Load Shed Interconnection - Drawing No. 0G8774-C

Section 6 — Electrical Data

RTSS Type Transfer Switch

Electrical Schematic - Drawing No. 0G7816-B

Section 6 — Electrical Data

RTSS Type Transfer Switch

Electrical Schematic - Drawing No. 0G7816-B

Section 6 — Electrical Data

RTSS Type Transfer Switch

Wiring Diagram - Drawing No. 0G7817-C

Section 6 — Electrical Data

RTSS Type Transfer Switch

Wiring Diagram - Drawing No. 0G7817-C

Section 7 — Exploded Views & Parts Lists

RTSS Type Transfer Switch

Load Shed Transfer Switch - Drawing No. 0G8054$-G

Parts List on page 21.

La page est en cours de chargement...

Generac 20 kW G0055060 Manuel utilisateur

Marque: Generac

Modèle: 20 kW G0055060

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Generac 20 kW G0055060 User manual

Generac 20 kW G0055060 Manuel utilisateur

Generac 20 kW G0055060 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents