12
1
1
2
3
4
5
6
7
STICKER (Q=4000Kg)
STICKER (INSTRUCTIONS)
STICKER (SERIAL NUMBER)
STICKER (ROTARYLIFT)
STICKER (WARNING)
STICKER (MAINTENANCE)
STICKER (LOAD DISTRIBUTION)
999921600
999909850
999921570
999921580
999921590
999921610
999912071
Refer to full operating manual.
The lift may only be operated by authorized staff.
The lift must be used for its intended purpose only.
Do not exceed the load capacity specifi ed on the Serial plate.
The weight distribution at the front/back may not exceed the value
given in the full operating manual.
Comply with the statutory Health and Safety regulations.
Do not carry persons on the lift.
Apply the vehicle handbrake after driving onto the lift and before
lifting the vehicle.
The main switch is also an emergency stop switch .In case
of emergency, turn the switch to "O".
Secure the lift against unauthorized use by locking the main switch.
Obstacles must be kept out of range of moving load and lift.
1. BEFORE LOADING:
Check that the lift is in full working order. Refer to the
Operating and Service Manual.
The lift must be fully lowered, there must be no objects, grease and
oil on the arms and rubber pads and people in the work area.
Swing the arms with the adapters free of oil and grease all the way
to the drive -through position.
Main switch to "ON".
Swing the arms under the vehicle and position the adapters on the
pick-up points recommended by the vehicle manufacturer.
If necessary, use optional adapters.
2. LIFTING:
There must be No one on the lift or in the vehicle when lifting
and lowering.
Press the "UP" button. Before the adapters make contact with
the vehicle, stop the lift .Ensure that all the arm restraints are fully engaged.
If necessary, move the arm slightly until the restraint fully engages
in the restraint gear. Do Not hit the pins with a hammer, since doing so
could damage the restraint gear teeth!
Do not leave parts lying around on the lift and on the vehicle you want to lift.
When fi tting or disassembling heavy vehicle parts, make sure that the
centre of the vehicle does not shift! The vehicle must be secured beforehand.
The vehicle must always rest on 4 pick-up points or be secured
against movement.
Only continue the lifting process up to the desired height if the vehicle
is stable.
Do not leave the lift at its full rise for long periods.
Lower the lift onto the safety latches.
3. WHEN LIFTING:
Prevent the vehicle from rocking.
The vehicle doors must be closed when raising and lowering.
Monitor the load and the lift when raising and lowering.
Do not loiter within range of the moving load and lift when raising
and lowering.
Do not climb onto the raised vehicle or the lift.
4. BEFORE LOWERING THE LIFT:
Remove obstacles from under the car and lift.
Do not loiter within the work area of the lift.
5. LOWERING:
Press the "UP" button, if you want to raise the lift out of the
locking mechanism .
Press the "Lower" button and lower to the desired height .If the lift
is M-version , Operate the release lever down at the same time.
6. DRIVING OFF:
The lift must be fully lowered.
Swing the arms all the way to the drive-through position .Only then
move the vehicle.
7. SWITCHING OFF:
When the lift is not in use, turn the main switch to "OFF".
8. TROUBLESHOOTING AND MAINTENANCE:
Refer to the operating and Service Manual.
TOTAL LIFT CAPACITY
4000 KG
Refer to full operating manual.
The lift may only be operated by authorized staff.
The lift must be used for its intended purpose only.
Do not exceed the load capacity specifi ed on the Serial plate.
The weight distribution at the front/back may not exceed the value
given in the full operating manual.
Comply with the statutory Health and Safety regulations.
Do not carry persons on the lift.
Apply the vehicle handbrake after driving onto the lift and before
lifting the vehicle.
The main switch is also an emergency stop switch .In case
of emergency, turn the switch to "O".
Secure the lift against unauthorized use by locking the main switch.
Obstacles must be kept out of range of moving load and lift.
1. BEFORE LOADING:
Check that the lift is in full working order. Refer to the
Operating and Service Manual.
The lift must be fully lowered, there must be no objects, grease and
oil on the arms and rubber pads and people in the work area.
Swing the arms with the adapters free of oil and grease all the way
to the drive -through position.
Main switch to "ON".
Swing the arms under the vehicle and position the adapters on the
pick-up points recommended by the vehicle manufacturer.
If necessary, use optional adapters.
2. LIFTING:
There must be No one on the lift or in the vehicle when lifting
and lowering.
Press the "UP" button. Before the adapters make contact with
the vehicle, stop the lift .Ensure that all the arm restraints are fully engaged.
If necessary, move the arm slightly until the restraint fully engages
in the restraint gear. Do Not hit the pins with a hammer, since doing so
could damage the restraint gear teeth!
Do not leave parts lying around on the lift and on the vehicle you want to lift.
When fi tting or disassembling heavy vehicle parts, make sure that the
centre of the vehicle does not shift! The vehicle must be secured beforehand.
The vehicle must always rest on 4 pick-up points or be secured
against movement.
Only continue the lifting process up to the desired height if the vehicle
is stable.
Do not leave the lift at its full rise for long periods.
Lower the lift onto the safety latches.
3. WHEN LIFTING:
Prevent the vehicle from rocking.
The vehicle doors must be closed when raising and lowering.
Monitor the load and the lift when raising and lowering.
Do not loiter within range of the moving load and lift when raising
and lowering.
Do not climb onto the raised vehicle or the lift.
4. BEFORE LOWERING THE LIFT:
Remove obstacles from under the car and lift.
Do not loiter within the work area of the lift.
5. LOWERING:
Press the "UP" button, if you want to raise the lift out of the
locking mechanism .
Press the "Lower" button and lower to the desired height .If the lift
is M-version , Operate the release lever down at the same time.
6. DRIVING OFF:
The lift must be fully lowered.
Swing the arms all the way to the drive-through position .Only then
move the vehicle.
7. SWITCHING OFF:
When the lift is not in use, turn the main switch to "OFF".
8. TROUBLESHOOTING AND MAINTENANCE:
Refer to the operating and Service Manual.
TOTAL LIFT CAPACITY
4000 KG
Refer to full operating manual.
The lift may only be operated by authorized staff.
The lift must be used for its intended purpose only.
Do not exceed the load capacity specifi ed on the Serial plate.
The weight distribution at the front/back may not exceed the value
given in the full operating manual.
Comply with the statutory Health and Safety regulations.
Do not carry persons on the lift.
Apply the vehicle handbrake after driving onto the lift and before
lifting the vehicle.
The main switch is also an emergency stop switch .In case
of emergency, turn the switch to "O".
Secure the lift against unauthorized use by locking the main switch.
Obstacles must be kept out of range of moving load and lift.
1. BEFORE LOADING:
Check that the lift is in full working order. Refer to the
Operating and Service Manual.
The lift must be fully lowered, there must be no objects, grease and
oil on the arms and rubber pads and people in the work area.
Swing the arms with the adapters free of oil and grease all the way
to the drive -through position.
Main switch to "ON".
Swing the arms under the vehicle and position the adapters on the
pick-up points recommended by the vehicle manufacturer.
If necessary, use optional adapters.
2. LIFTING:
There must be No one on the lift or in the vehicle when lifting
and lowering.
Press the "UP" button. Before the adapters make contact with
the vehicle, stop the lift .Ensure that all the arm restraints are fully engaged.
If necessary, move the arm slightly until the restraint fully engages
in the restraint gear. Do Not hit the pins with a hammer, since doing so
could damage the restraint gear teeth!
Do not leave parts lying around on the lift and on the vehicle you want to lift.
When fi tting or disassembling heavy vehicle parts, make sure that the
centre of the vehicle does not shift! The vehicle must be secured beforehand.
The vehicle must always rest on 4 pick-up points or be secured
against movement.
Only continue the lifting process up to the desired height if the vehicle
is stable.
Do not leave the lift at its full rise for long periods.
Lower the lift onto the safety latches.
3. WHEN LIFTING:
Prevent the vehicle from rocking.
The vehicle doors must be closed when raising and lowering.
Monitor the load and the lift when raising and lowering.
Do not loiter within range of the moving load and lift when raising
and lowering.
Do not climb onto the raised vehicle or the lift.
4. BEFORE LOWERING THE LIFT:
Remove obstacles from under the car and lift.
Do not loiter within the work area of the lift.
5. LOWERING:
Press the "UP" button, if you want to raise the lift out of the
locking mechanism .
Press the "Lower" button and lower to the desired height .If the lift
is M-version , Operate the release lever down at the same time.
6. DRIVING OFF:
The lift must be fully lowered.
Swing the arms all the way to the drive-through position .Only then
move the vehicle.
7. SWITCHING OFF:
When the lift is not in use, turn the main switch to "OFF".
8. TROUBLESHOOTING AND MAINTENANCE:
Refer to the operating and Service Manual.
TOTAL LIFT CAPACITY
4000 KG
Refer to full operating manual.
The lift may only be operated by authorized staff.
The lift must be used for its intended purpose only.
Do not exceed the load capacity specifi ed on the Serial plate.
The weight distribution at the front/back may not exceed the value
given in the full operating manual.
Comply with the statutory Health and Safety regulations.
Do not carry persons on the lift.
Apply the vehicle handbrake after driving onto the lift and before
lifting the vehicle.
The main switch is also an emergency stop switch .In case
of emergency, turn the switch to "O".
Secure the lift against unauthorized use by locking the main switch.
Obstacles must be kept out of range of moving load and lift.
1. BEFORE LOADING:
Check that the lift is in full working order. Refer to the
Operating and Service Manual.
The lift must be fully lowered, there must be no objects, grease and
oil on the arms and rubber pads and people in the work area.
Swing the arms with the adapters free of oil and grease all the way
to the drive -through position.
Main switch to "ON".
Swing the arms under the vehicle and position the adapters on the
pick-up points recommended by the vehicle manufacturer.
If necessary, use optional adapters.
2. LIFTING:
There must be No one on the lift or in the vehicle when lifting
and lowering.
Press the "UP" button. Before the adapters make contact with
the vehicle, stop the lift .Ensure that all the arm restraints are fully engaged.
If necessary, move the arm slightly until the restraint fully engages
in the restraint gear. Do Not hit the pins with a hammer, since doing so
could damage the restraint gear teeth!
Do not leave parts lying around on the lift and on the vehicle you want to lift.
When fi tting or disassembling heavy vehicle parts, make sure that the
centre of the vehicle does not shift! The vehicle must be secured beforehand.
The vehicle must always rest on 4 pick-up points or be secured
against movement.
Only continue the lifting process up to the desired height if the vehicle
is stable.
Do not leave the lift at its full rise for long periods.
Lower the lift onto the safety latches.
3. WHEN LIFTING:
Prevent the vehicle from rocking.
The vehicle doors must be closed when raising and lowering.
Monitor the load and the lift when raising and lowering.
Do not loiter within range of the moving load and lift when raising
and lowering.
Do not climb onto the raised vehicle or the lift.
4. BEFORE LOWERING THE LIFT:
Remove obstacles from under the car and lift.
Do not loiter within the work area of the lift.
5. LOWERING:
Press the "UP" button, if you want to raise the lift out of the
locking mechanism .
Press the "Lower" button and lower to the desired height .If the lift
is M-version , Operate the release lever down at the same time.
6. DRIVING OFF:
The lift must be fully lowered.
Swing the arms all the way to the drive-through position .Only then
move the vehicle.
7. SWITCHING OFF:
When the lift is not in use, turn the main switch to "OFF".
8. TROUBLESHOOTING AND MAINTENANCE:
Refer to the operating and Service Manual.
TOTAL LIFT CAPACITY
4000 KG
Refer to full operating manual.
The lift may only be operated by authorized staff.
The lift must be used for its intended purpose only.
Do not exceed the load capacity specifi ed on the Serial plate.
The weight distribution at the front/back may not exceed the value
given in the full operating manual.
Comply with the statutory Health and Safety regulations.
Do not carry persons on the lift.
Apply the vehicle handbrake after driving onto the lift and before
lifting the vehicle.
The main switch is also an emergency stop switch .In case
of emergency, turn the switch to "O".
Secure the lift against unauthorized use by locking the main switch.
Obstacles must be kept out of range of moving load and lift.
1. BEFORE LOADING:
Check that the lift is in full working order. Refer to the
Operating and Service Manual.
The lift must be fully lowered, there must be no objects, grease and
oil on the arms and rubber pads and people in the work area.
Swing the arms with the adapters free of oil and grease all the way
to the drive -through position.
Main switch to "ON".
Swing the arms under the vehicle and position the adapters on the
pick-up points recommended by the vehicle manufacturer.
If necessary, use optional adapters.
2. LIFTING:
There must be No one on the lift or in the vehicle when lifting
and lowering.
Press the "UP" button. Before the adapters make contact with
the vehicle, stop the lift .Ensure that all the arm restraints are fully engaged.
If necessary, move the arm slightly until the restraint fully engages
in the restraint gear. Do Not hit the pins with a hammer, since doing so
could damage the restraint gear teeth!
Do not leave parts lying around on the lift and on the vehicle you want to lift.
When fi tting or disassembling heavy vehicle parts, make sure that the
centre of the vehicle does not shift! The vehicle must be secured beforehand.
The vehicle must always rest on 4 pick-up points or be secured
against movement.
Only continue the lifting process up to the desired height if the vehicle
is stable.
Do not leave the lift at its full rise for long periods.
Lower the lift onto the safety latches.
3. WHEN LIFTING:
Prevent the vehicle from rocking.
The vehicle doors must be closed when raising and lowering.
Monitor the load and the lift when raising and lowering.
Do not loiter within range of the moving load and lift when raising
and lowering.
Do not climb onto the raised vehicle or the lift.
4. BEFORE LOWERING THE LIFT:
Remove obstacles from under the car and lift.
Do not loiter within the work area of the lift.
5. LOWERING:
Press the "UP" button, if you want to raise the lift out of the
locking mechanism .
Press the "Lower" button and lower to the desired height .If the lift
is M-version , Operate the release lever down at the same time.
6. DRIVING OFF:
The lift must be fully lowered.
Swing the arms all the way to the drive-through position .Only then
move the vehicle.
7. SWITCHING OFF:
When the lift is not in use, turn the main switch to "OFF".
8. TROUBLESHOOTING AND MAINTENANCE:
Refer to the operating and Service Manual.
TOTAL LIFT CAPACITY
4000 KG
3
2 5 4 1
6
7
3
7
2
5
4
4
1
1
6
EN1493-2010
3250
3600
4000
100030001000
900
2700
900
815
2435
800
Q=P1+P2
kg
P2
kg
P1
kg
C
mm
RIPARTIZIONE DEL CARICO
LOAD DISTRIBUTION
GEWICHT VERTEILUNG
REPARTITION DE CHARGE
REPARTICION DE LA CARGA
P2(P1)
P1(P2)
Q
C
3000
750
2250
700