Toro 51988 Manuel utilisateur

Catégorie
Souffleurs / sécheurs d'air
Taper
Manuel utilisateur
Powervac
Item No. 51988—315000001 & Up
English (EN), French (FR), and Spanish (ES)
WARNING:
To reduce the risk of injury, the user must read and understand the Operators Manual. Save this manual.
Form No. 3389-623 Rev. A
If you have questions concerning
your blower, please call us
at 1-866-574-9242 (US) or
1-866-574-9243 (Canada).
NOTICE
Do not use E15 or E85 fuel in this product.
It is a violation of federal law and will dam-
age the unit and void your warranty. Only
use unleaded gasoline containing up to 10%
ethanol.
®
2
READ THIS INFORMATION
Before you use your new Powervac
, read the following helpful hints to
get you started.
Fueling
WARNING:
Gasoline and its vapors are highly ammable and
explosive. To prevent serious personal injury and
property damage, handle it with care. Keep away
from ignition sources and open ames, handle
outdoors only, do not smoke and wipe up spills
immediately.
1. Obtain a clean container that is approved for use with gasoline.
2. Mix all of the 2-cycle oil provided with 1 US gallon of 87-octane, unleaded
gasoline (50:1).
3. Fill the blowers fuel tank carefully.
Cold Starting vs. Warm Starting
When you restart the blower and you are not sure whether the engine is still warm, set the choke
lever to RUN, lock the throttle wide open, and pull the starter grip and rope. If the engine does not
start within 5 pulls, refer to “To Start a Cold Engine” later in this manual.
Flooded Engine
Will the engine start? If not, it may be ooded. Relax, this is easy to correct. Set the choke lever to
RUN. Squeeze the trigger and pull the starter grip and rope quickly for 10 to 12 pulls.
If the engine does not start, refer to Troubleshooting later in this manual or call toll-free at
866-574-9242 (US) or 866-574-9243 (Canada).
CALL
1-866-574-9242 (US) or
1-866-574-9243 (Canada)
For questions concerning your blower,
call us toll free at 1-866-574-9242 (US) or
1-866-574-9243 (Canada).
STOP
3
Table of Contents
Introduction ................................................................................................................................................................................... 4
General Safety Rules .....................................................................................................................................................................5
Specic Safety Rules ....................................................................................................................................................................6
Symbols.........................................................................................................................................................................................7
Product Labels ..............................................................................................................................................................................8
Features ................................................................................................................................................................................... 9-10
Product Specications ...........................................................................................................................................................9
Know Your Blower/Vacuum ................................................................................................................................................ 10
Assembly................................................................................................................................................................................11-13
Unpacking ............................................................................................................................................................................11
Packing List .........................................................................................................................................................................11
Tools Needed .......................................................................................................................................................................11
Assembling the Blower Tubes ............................................................................................................................................. 11
Installing the Vacuum Bag ................................................................................................................................................... 12
Installing the Vacuum Tubes ................................................................................................................................................ 13
Operation ............................................................................................................................................................................... 14-17
Applications .........................................................................................................................................................................14
Fueling and Refueling ..........................................................................................................................................................14
Oxygenated Fuels ................................................................................................................................................................15
Starting and Stopping ..........................................................................................................................................................15
Operating the Blower ........................................................................................................................................................... 16
Throttle Lock .......................................................................................................................................................................17
Vacuum Operation ...............................................................................................................................................................17
Maintenance .......................................................................................................................................................................... 18-20
General Maintenance ...........................................................................................................................................................18
Cleaning the Product ............................................................................................................................................................18
Servicing the Product ........................................................................................................................................................... 18
Checking the Fuel Cap, Tank and Lines ..............................................................................................................................18
Cleaning the Air Filter .........................................................................................................................................................19
Cleaning the Exhaust Port, Muer and Spark Arrestor ......................................................................................................19
Vacuum Bag ......................................................................................................................................................................... 19
Spark Plug Replacement ...................................................................................................................................................... 19
Storing the Product ..............................................................................................................................................................20
High Altitude Engine Operation ..........................................................................................................................................20
Maintenance Schedule .........................................................................................................................................................20
Troubleshooting ..........................................................................................................................................................................21
Warranty ...................................................................................................................................................................................... 22
Table of Contents
4
®
Introduction
Thank you for purchasing a Toro product.
We would like for you to be completely satised with your new product, so feel free to contact a qualied service dealer for
help with service, genuine Toro parts, or other information you may require.
Whenever you contact a qualied service dealer, always know the model and serial numbers of the product. These numbers
will help the service representative provide exact information about your specic product. You will nd the model and serial
number data label located on the bottom of the housing.
For your convenience, write the product model and serial numbers in the space below.
Item No.
Serial No.
Manufactuing No.
Read this manual carefully to learn how to operate and maintain your product correctly. Reading this manual will help you
and others avoid personal injury and damage to the product. Although Toro designs, produces, and markets safe, state-of-the-
art products, you are responsible for using the product properly and safely. You are also responsible for training persons you
allow to use the product about safe operation.
The Toro warning system in this manual identies potential hazards and has special safety messages that help you and others
avoid personal injury, even death. DANGER, WARNING, and CAUTION are signal words that identify the level of hazard.
However, regardless of the hazard, be extremely careful. Two other words, “Important” and “Note,” highlight information.
Introduction
Data
Label
Bottom View
5
Read All Instructions
Do not allow children or untrained individuals to use
this unit.
Do not start or operate the engine in a conned space,
building, near open windows, or in other unventilated
space where dangerous carbon monoxide fumes can
collect. Carbon monoxide, a colorless, odorless, and
extremely dangerous gas, can cause unconsciousness or
death.
Always wear eye protection with side shields marked to
comply with ANSI Z87.1, along with hearing protec-
tion. Failure to do so could result in objects being
thrown into your eyes and other possible serious inju-
ries.
Keep all bystanders, children, and pets at least 50 ft.
away.
Wear heavy long pants, long sleeves, boots, and gloves.
Do not wear loose tting clothing, short pants, sandals,
jewelry of any kind, or go barefoot.
To reduce the risk of injury associated with objects
being drawn into rotating parts, do not wear loose cloth-
ing, scarves, neck chains, etc.
Secure long hair so it is above shoulder level to prevent
entanglement in any rotating parts.
Do not operate this unit when you are tired, ill, upset, or
under the inuence of alcohol, drugs, or medication.
Do not operate in poor lighting.
Keep all parts of your body away from any moving
parts and all hot surfaces of the unit.
Wear a face lter mask in dusty conditions to reduce the
risk of injury associated with the inhalation of dust.
Check the work area before each use. Remove all
objects such as rocks, broken glass, nails, wire, or
string which can be thrown or become entangled in the
machine.
Keep rm footing and balance. Do not overreach. Over-
reaching can result in loss of balance or exposure to hot
surfaces.
Before storing, allow the engine to cool.
Empty fuel tank into a container approved for gasoline
and restrain the unit from moving before transporting in
a vehicle.

To reduce the risk of re and burn injury, handle fuel
with care. It is highly ammable.

Do not smoke while handling fuel.

Mix and store fuel in a container approved for gasoline.
Mix fuel outdoors where there are no sparks or ames.
Select bare ground, stop engine, and allow to cool
before refueling.
Loosen fuel cap slowly to release pressure and to keep
fuel from escaping around the cap.
Tighten the fuel cap securely after refueling.
Wipe spilled fuel from the unit. Move 30 ft. away from
refueling site before starting engine.
Never attempt to burn o spilled fuel under any circum-
stances.
Maintain the unit per maintenance instructions in this
Operators Manual.
Inspect the unit before each use for loose fasteners, fuel
leaks, etc. Replace damaged parts.
Do not use on a ladder, rooftop, tree, or other unstable
support. Stable footing on a solid surface enables better
control of the blower in unexpected situations.
Service
Before cleaning, repairing, or inspecting, shut o the
engine and make certain all moving parts have stopped.
Disconnect the spark plug wire, and keep the wire away
from the plug to prevent starting.
We recommend taking your equipment to a qualied
service center for repair, as service performed by
inexperienced or unqualied persons may damage the
equipment, create unsafe conditions, injury to user and/
or void your warranty.
Use only recommended or equivalent replacement parts
and accessories. Use of any other parts may create a
hazard or cause product damage.
General Safety Rules
General Safety Rules
WARNING:
Read and understand all instructions. Failure to follow all instructions listed below may result in electric
shock, re and/or carbon monoxide poisoning which will cause death or serious personal injury.
6
Specific Safety Rules
Specific Safety Rules
Always hold the blower/vacuum in your right hand dur-
ing blower operation. Refer to the Operation instruc-
tions later in this manual for proper position during
vacuum operation and additional information.
Never place objects inside the blower tubes.
Use only as directed in this operators manual.
Do not operate vacuum without vacuum bag installed;
ying debris could cause serious injury. Always close
vacuum bag completely before operating.
Rotating impeller blades can cause severe injury. Stop
the engine and ensure impeller blades have stopped
rotating before opening the vacuum door or installing/
changing tubes. Do not put hands or any other object
into the vacuum tubes while they are installed on the
unit.
Never run the unit without the proper equipment
attached. When used as a blower, always install the
blower tubes. When used as a vacuum, always install
the vacuum tubes and vacuum bag. Make sure the
vacuum bag is completely zipped when the unit is run-
ning to avoid ying debris.
Avoid situations that could catch the vacuum bag on
re. Do not operate near an open ame. Do not vacuum
warm ash from replaces, barbecue pits, brush piles,
etc. Do not vacuum discarded cigars or cigarettes unless
the cinders are completely cool.
Never place blower on any surface, except a hard, clean
surface when engine is running. Gravel, sand, and other
debris can be picked up by the air inlet and thrown at
the operator or bystanders, causing possible serious
injuries.
To reduce the risk of hearing loss associated with sound
level(s), hearing protection is required.
To reduce the risk of injury associated with contact-
ing rotating parts, stop the engine before installing or
removing attachments. Always disconnect the spark
plug before performing maintenance or accessing any
movable parts.
Never use blower near res, replaces, hot ashes, bar-
becue pits, etc., which may cause re to spread.
Do not point the blower nozzle in the direction of
people or pets.
Never run the unit without the proper equipment at-
tached. Always ensure the blower tubes are installed.
This product is intended for infrequent use by home-
owners and other occasional users for such general ap-
plications as blowing leaves and lawn clippings, etc. It
is not intended for prolonged use. Prolonged periods of
operation can cause circulatory problems in the users
hands due to vibration. For such use, it may be appro-
priate to use a product having an anti-vibration feature.
Fueling
Fuel is highly ammable. Take precautions when using
to reduce the chance of serious personal injury.
Store fuel in a cool, well-ventilated area, safely away
from spark and/or ame-producing equipment.
Store fuel in containers specically designed for this
purpose.
Only refuel outdoors and do not smoke while refueling.
Add fuel before starting the engine. Never remove the
cap of the fuel tank or add fuel while the engine is run-
ning or when the engine is hot.
Do not smoke while handling fuel.
Mix and store fuel in a container approved for gasoline.
Mix fuel outdoors where there are no sparks or ames.
Loosen fuel cap slowly to release pressure and to keep
fuel from escaping around the cap.
Tighten the fuel cap securely after refueling.
Wipe spilled fuel from the unit. Move 30 feet away
from refueling site before starting engine.
Never attempt to burn o spilled fuel under any circum-
stances.
To reduce the risk of re and burn injury, handle fuel
with care. It is highly ammable.
If fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
Replace all fuel tank and container caps securely.
Empty fuel tank into a container approved for gasoline
and restrain the unit from moving before transporting in
a vehicle.
When draining the fuel tank, use an approved fuel stor-
age container in a well-ventilated area.
Select bare ground, stop engine, and allow to cool
before refueling.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan someone this tool, loan them these instructions
also.
7
Symbols
Symbols
Some of the following symbols may be used on this product. Please study them and learn their meaning for safe opera-
tion of this product.
SYMBOL NAME EXPLANATION
Safety Alert Symbol Indicates a potential personal injury hazard.
Read Operators Manual
To reduce the risk of injury, user must read and understand opera-
tors manual before using this product.
Wear Eye and Hearing
Protection
Always wear eye protection with side shields marked to comply
with ANSI Z87.1 as well as hearing protection when operating
this equipment.
Keep Bystanders Away Keep all bystanders at least 50 ft. away.
Ricochet
Thrown objects can ricochet and result in personal injury or
property damage.
Vacuum Door Do not run unit while vacuum door is unsecured.
Long Hair Risk of long hair being drawn into air inlet.
Blower Tubes Do not run unit without tubes in place.
Loose Clothing Risk of loose clothing being drawn into air intake.
Gasoline and Lubricant
Use unleaded gasoline intended for motor vehicle use with an oc-
tane rating of 87 [(R + M) / 2] or higher. This product is powered
by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle
lubricant.
Stop Symbol
To stop the engine, press and hold the stop switch in the stop
position
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
Indicates a hazardous situation, which, if not avoided, will result in death or serious
injury.
WARNING:
Indicates a hazardous situation, which, if not avoided, could result in death or seri-
ous injury.
CAUTION:
Indicates a hazardous situation, that, if not avoided, may result in minor or moderate
injury.
NOTICE:
(Without Safety Alert Symbol) Indicates information considered important, but not
related to a potential injury (e.g. messages relating to property damage).
8
Product Labels
Product labels and instructions are easily visible to the operator and are located near any area of potential danger.
Replace damaged or lost labels.
Product Labels
Part No. 941727005 Part No. 940908003
Part No. 940907028
Part No. 940835008
Part No. 940654088
Part No. 940907027
Part No. 940907029
Part No. 941727006 Part No. 940991054
Part No. 527990001
Part No. 941727009
9
®
Figure 1
Features
Product Specifications
Name Specification
Engine 25.4cc Full Crank
Air Velocity
MPH Up to 150 (241.39 kph)
CFM Up to 460 (13 m
3
/min)
Features
Upper
Vacuum Tube
Vacuum Bag
Raised Slot
Lower
Vacuum Tube
Vacuum Bag
Shoulder Strap
Vacuum Tube
Screw
Main
Housing
®
Primer Bulb
Primer Bulb
Muffler
Starter Grip
and Rope
Vacuum Handle
Fuel Cap
Air Filter
Cover Tab
Upper Handle
Throttle
Lock
Throttle
Trigger
Spark Plug
Choke Lever
RUN
HALF
FULL
Stop Switch
Vacuum Bag
Adaptor
10
®
®
Know Your Blower/Vacuum
See Figures 1 - 2.
The safe use of this product requires an understanding of the
information on the tool and in this operators manual as well
as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
Blower Tube and Sweeper Nozzle
The blower tubes and sweeper nozzle can be assembled and
installed on the main housing using no tools.
Engine
The blower has a powerful 25.4cc engine with sucient
power to handle tough blowing and vacuuming jobs.
Mulcher
The blower is equipped with a metal mulching blade that
eciently reduces leaves at a 10:1 ratio.
Sweeper Nozzle
The sweeper nozzle allows for more area to be covered
during blower operation.
Throttle Lock
The throttle lock feature allows the user to operate the
blower without holding the throttle trigger. To slow the
engine speed, simply push the throttle lock forward.
Throttle Trigger
The blower can be operated at any speed between idle and
full throttle.
Vacuum/Mulcher
Converting the blower to a vacuum/mulcher is simple and
can be done using a straight screwdriver.
Vacuum Bag
The vacuum bag attaches to the main housing easily by
using the vacuum bag adaptor.
Vacuum Handle
This feature allows user to perform vacuuming duties
comfortably.
Vacuum Tubes
The vacuum tubes can be installed on the main housing
using a at head screw driver.
Features
Figure 2
Upper
Handle
Upper
Blower Tube
Muffler
Vacuum
Inlet Door
Throttle
Lock
Throttle
Trigger
Sweeper Nozzle
Stop Switch
Main
Housing
11
Assembly
Assembly
Flat Head Screwdriver
WARNING:
To prevent accidental starting that could cause
serious personal injury, always disconnect the
engine spark plug wire from the spark plug
when assembling parts.
Tools Needed
The following tool (not included or drawn to scale) is
needed for assembly:
Unpacking
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing
list are included.
WARNING:
Do not use this product if any parts on the Pack-
ing List are already assembled to your product
when you unpack it. Parts on this list are not as-
sembled to the product by the manufacturer and
require customer installation. Use of a product
that may have been improperly assembled could
result in serious personal injury.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
If any parts are damaged or missing, please call
1-866-574-9242 (US) or 1-866-574-9243 (Canada) for
assistance.
Packing List
Blower
Upper Blower Tube
Sweeper Nozzle
Upper and Lower Vacuum Tubes
Vacuum Tube Screws (2)
Vacuum Bag Assembly
Vacuum Bag Adaptor
2-Cycle Engine Lubricant
Operators Manual
Note: Read and remove all hang tags and store with your
Operators Manual.
WARNING:
If any parts are damaged or missing do not
operate this product until the parts are replaced.
Use of this product with damaged or missing
parts could result in serious personal injury.
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modication is
misuse and could result in a hazardous condi-
tion leading to possible serious personal injury.
Figure 3
Sweeper
Nozzle
Upper
Blower Tube
Main Housing
Outlet
Raised
Locking Tab
Assembling and Disassembling Upper
Blower Tube and Sweeper Nozzle
See Figure 3 - 4.
1. Align raised tabs on main housing to the slots on upper
tube; slide together and tighten securely by twisting
until the tubes snap into the locked position. Check
tightness after initial run and retighten if needed.
NOTICE:
When correctly assembled, the tubes are dif-
cult to separate. If they can easily be twisted
apart, the tubes are not locked. Continue twisting
together until the tubes snap into the locked posi-
tion. Tubes that are not fully locked together can
separate during blower operation.
2. Secure the sweeper nozzle and upper blower tube
together by aligning the raised locking tab on the upper
blower tube with the raised slot on the sweeper nozzle.
3. To disassemble, raise the locking tab with a at head
screwdriver, rotate the tube and nozzle to unlock them
and remove from the main housing outlet.
12
Installing the Vacuum Bag
See Figures 5 - 6.
1. Remove the sweeper nozzle and upper blower tube
from the main housing by twisting and removing from
main housing outlet.
2. Unzip the vacuum bag and place the adaptor inside
as shown. Push the vacuum bag adaptor through the
opening opposite the zipper. The wider end of the adap-
tor will remain on the inside of the vacuum bag when
installed properly.
3. Align the raised slots on the vacuum bag adaptor with
the raised locking tabs on the main housing outlet; push
the bag adaptor onto the housing. Twist to lock into
place.
4. Rotate the vacuum bag until the shoulder strap is up-
right.
5. Make sure the vacuum bag is zipped and closed before
starting the unit.
Assembly
To remove the vacuum bag:
1. Remove the vacuum bag by using a at head screw-
driver to lift the locking tab.
2. Rotate counterclockwise to unlock the adaptor and
remove.
Figure 5
Vacuum Bag Adaptor
Vacuum Bag
Figure 6
Vacuum Bag
Adaptor Installed
to housing
Raised
Locking
Tab
Main
Housing
Outlet
Figure 7
Vacuum
Inlet Door
Vacuum
Door
Hinge
Door Tab
Vacuum Bag
Assembly
Raised
Tab
Figure 4
®
Tab
Blower /
Vacuum Tube
13
®
®
Assembly
Figure 9
Upper
Vacuum Tube
Lower
Vacuum Tube
Screws
Slots
Tabs
Upper
Vacuum Tube
Slot
Vacuum
Inlet Door
Lock
Unlock
Installing the Vacuum Tubes
See Figures 7 - 9
WARNING:
Rotating impeller blades can cause severe injury.
Always stop the engine and ensure impeller
blades have stopped rotating before opening the
vacuum door or installing/changing tubes. Do
not put hands or any other object into the vacuum
tubes while they are installed on the unit.
Tab
Vacuum Tube
Figure 8
To install the vacuum tubes:
1. Secure the upper and lower vacuum tubes together by
aligning the raised locking tabs with the raised slots.
2. Tap tube assembly on ground until the screw holes
in lower tube are in the raised slot of the upper tube.
Secure with supplied screws.
3. Depress door tabs using a straight screwdriver and open
vacuum inlet door.
4. Align the slots on the vacuum tube housing with the
tabs on the main housing.
5. Turn the vacuum tube housing clockwise to to the
locked position and secure to the main housing.
To remove the vacuum tubes:
1. Using a screwdriver, depress the tab on the blower/
vacuum tube to unlock.
2. Turn the upper vacuum tube housing counterclockwise.
3. Remove the vacuum tube assembly from the main
housing.
4. Close the inlet cover door securely.
Vacuum
Tube Housing
Tabs
Vacuum
Opening
14
Operation
WARNING:
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second is sucient to inict serious injury.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1, along with
hearing protection. Failure to do so could result
in objects being thrown into your eyes and other
possible serious injuries.
NOTICE:
The spark arrestor on this product has not been
evaluated by the USDA Forest Service and
cannot be used on U.S. forest lands. In addition,
product users must comply with Federal, State,
and local re prevention regulations. Check
with appropriate authorities. Contact customer
service or a qualied service center to purchase
a replacement spark arrestor.
NOTICE:
Before each use, inspect the entire product for
damaged, missing, or loose parts such as screws,
nuts, bolts, caps, etc. Tighten securely all fasten-
ers and caps and do not operate this product until
all missing or damaged parts are replaced. Please
contact customer service or a qualied service
center for assistance.
Applications
You may use this tool for the purposes listed below:
Clear leaves and other debris from your lawn
Keep decks and driveways free from leaves and pine
needles
Vacuuming leaves from your lawn
Fueling and Refueling
WARNING:
Gasoline is extremely ammable and explosive.
A re or explosion from gasoline will burn you
and others. Always shut o engine before fuel-
ing. Never add fuel to a machine with a running
or hot engine. Move at least 30 ft. from refuel-
ing site before starting engine. Do not smoke
and stay away from open ames and sparks.
Failure to safely handle fuel could result in seri-
ous personal injury.
Fuel Mixture
This product is powered by a 2-cycle engine and requires
pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded
gasoline and 2-cycle engine lubricant in a clean container
approved for gasoline. DO NOT mix quantities larger than
usable in a 30-day period.
Recommended fuel: This engine is certied to operate on
unleaded gasoline intended for automotive use.
Ethanol. Gasoline containing up to 10% ethanol by volume
(commonly referred to as E10) is acceptable. E15 and E85
are not.
Note: We recommend you use high-quality synthetic 2-cycle
lubricant in this product. Mix at 2.6 oz. per gallon US (76 ml
par 3,8 L ).
Do not use automotive lubricant or 2-cycle outboard
lubricant.
HIGH QUALITY 2-CYCLE ENGINE LUBRICANT
GASOLINE LUBRICANT
1.0 gal. (US) (3.8 liter) 2.6 oz. (76 ml)
2.5 gal. (US) (9.5 liter) 6.4 oz. (189 ml)
Filling the Tank
1. Clean the surface around the fuel cap to prevent con-
tamination.
2. Loosen the fuel cap slowly, by turning it counterclock-
wise.
3. Pour the fuel mixture carefully into the tank.
4. Clean and inspect the fuel cap gasket before replacing
the fuel cap.
5. Replace the fuel cap and tighten it by turning it clock-
wise.
6. Wipe spilled fuel from the product.
7. Move at least 30 ft. (9 m) away from refueling area
before starting the product.
Note: It is normal for smoke to be emitted from a new
engine during rst use.
Operation
15
Operation
WARNING:
Always shut o engine before fueling. Never
remove fuel cap or add fuel to a machine with
a running or hot engine. Make sure the unit is
sitting on a at, level surface and only add fuel
outdoors. If the engine is hot, let the unit cool
for at least ve minutes before adding fuel.
After fueling, immediately replace fuel cap and
tighten securely. Move at least 30 ft. from refu-
eling site before starting engine. Do not smoke
and stay away from open ames and sparks!
Failure to follow these instructions could result
in a re and cause serious personal injury.
Ethanol-Blended Fuels
NOTICE:
Do not use E15 or E85 fuel in this product.
It is a violation of federal law and will dam-
age the unit and void your warranty. Only
use unleaded gasoline containing up to 10%
ethanol.
Starting and Stopping
See Figures 10 - 11.
To start a cold engine:
1. Set the blower on a at, bare surface.
2. Slowly press the primer bulb 8 times.
Note: After the 8th press, fuel should be visible in the
primer bulb. If it is not, continue to press the primer
until you see fuel in the bulb.
®
Primer Bulb
Stop
Switch
Starter
Grip and
Rope
Figure 10
STOP
Choke
Lever
Throttle
Trigger
B
RUN
HALF
FULL
RUN
HALF
FULL
RUN
HALF
FULL
B
RUN
HALF
FULL
RUN
HALF
FULL
RUN
HALF
FULL
Figure 11
Half
Choke
Full
Choke
Run
Position
B
RUN
HALF
FULL
RUN
HALF
FULL
RUN
HALF
FULL
3. Place the choke lever in the FULL CHOKE position.
4. Pull throttle lock back to lock the throttle wide open.
5. Pull the starter grip and rope sharply until engine at-
tempts to run. Do not pull the starter grip more than
four (4) times.
6. Set the choke lever in the HALF CHOKE position.
7. Pull the starter grip and rope until the engine runs. Do
not pull the starter grip more than six (6) times.
Note: If the engine does not start, return to the FULL
CHOKE position and repeat steps 3 through 6 again.
8. Allow the engine to run for 20 seconds, then place the
choke lever in the RUN position.
Note: In cooler environments, additional pulls of the
starter handle may be required with the choke lever in
the FULL CHOKE position.
To start warm engine:
1. Place the choke lever in the RUN position.
2. Pull throttle lock back to lock the throttle wide open.
3. Pull the starter grip and rope until the engine runs.
Note: If the engine does not start, repeat steps 3
through 7 again.
To stop the engine:
1. Press the stop switch to the stop (
STOP
) position, the
engine will stop. The switch will automatically return to
the on (I) position when released.
16
Proper Operating Position
Figure 12
Sweeper Nozzle
Figure 13
Operating the Blower
See Figures 12 - 13.
WARNING:
Never run the unit without the blower tubes
installed or the vacuum door securely closed.
Failure to follow these steps could result in pos-
sible serious injuries.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1, along with
hearing protection. Failure to do so could result
in objects being thrown into your eyes and other
possible serious injuries.
1. Start the blower. Refer to “Starting and Stopping”
earlier in this manual. Hold the blower with the upper
handle in your right hand.
WARNING:
Always hold the blower away from your body
with the handle in your right hand when operat-
ing as a blower, keeping clearance between your
body and the product. The muer side of the
blower should be away from your body. Any
contact with the housing can result in burns and/
or other serious personal injury.
Operation
WARNING:
Do not place blower on top of or near loose
debris or gravel. Debris may be sucked into
blower intake vent resulting in possible damage
to the unit and could result in serious personal
injury.
2. To keep from scattering debris, blow around the outer
edges of a debris pile. Never blow directly into the
center of a pile.
3. Operate power equipment at reasonable hours only - not
early in the morning or late at night when people might
be disturbed. Comply with the times listed in local
ordinances.
4. To reduce sound levels, limit the number of pieces of
equipment used at any one time.
5. Conserve water by using power blowers instead of
hoses for many lawn and garden applications, including
areas such as gutters, screens, patios, grills, porches,
and gardens.
6. Operate blower at the lowest possible throttle speed to
do the job.
7. Check your equipment before operation, especially the
muer, air intakes, and air lters.
8. Use rakes and brooms to loosen debris before blowing.
9. In dusty conditions, slightly dampen surfaces when
water is available.
10. Watch out for children, pets, open windows, or freshly
washed cars, and blow debris safely away.
11. Use the sweeper nozzle so the air stream can work close
to the ground.
12. After using blowers or other equipment, CLEAN UP!
Dispose of debris properly.
13. Use the sweeper nozzle for the everyday blowing op-
eration. This nozzle allows for more area to be covered
during the blowing operation.
17
Operation
Throttle Lock
See Figure 14
The throttle lock can be used to operate the blower without
holding the throttle trigger.
To engage the throttle lock:
1. Pull throttle lock back towards user, and stop at the
desired throttle setting.
2. To release the throttle lock, push throttle lock all the
way towards the front of unit.
Figure 15
Proper Operating Position
Hold Muffler Away From Body And Clothing
®
Figure 14
®
Throttle
Lock
Throttle
Trigger
Vacuum Operation
See Figure 15.
WARNING:
Never run the unit without the vacuum tubes
and vacuum bag installed. Failure to do so could
result in serious personal injury.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1, along with
hearing protection. Failure to do so could result
in objects being thrown into your eyes and other
possible serious injuries.
WARNING:
Keep the muer and all hot surfaces of the
blower/vacuum away from your body. Failure
to do so could result in possible serious personal
injury.
1. Install the vacuum tubes and bag. Refer to the Assem-
bly section earlier in this manual.
2. Start the engine. Refer to Starting and Stopping earlier
in this manual.
3. Place the vacuum bag strap over your left shoulder.
Hold the upper handle in your right hand and the
vacuum handle in your left hand.
4. Move the vacuum from side to side along outer edge of
the debris. To avoid clogging, do not place the vacuum
tube directly into the debris pile.
5. Hold the engine higher than the inlet end of the vacuum
tube.
6. Always point vacuum tube downhill when working on a
hillside.
7. To avoid injury to the operator or unit, do not pick up
rocks, broken glass, bottles, or other similar objects.
8. If the vacuum tubes should clog, stop the engine and
disconnect the spark plug wire before cleaning out the
obstruction.
9. Remove the vacuum tubes and clear the debris from
the blower fan housing. Remove the bag and clear the
adaptor. A small rod or stick may be required to clear
the entire tube length. Ensure that all debris has been
cleared before reassembling the vacuum tubes.
18
Maintenance
WARNING:
Do not at any time let brake uids, gasoline,
petroleum-based products, penetrating lubricants,
etc., come in contact with plastic parts. Chemi-
cals can damage, weaken or destroy plastic which
can result in serious personal injury.
Cleaning the Product
1.Stop the product before cleaning.
2.Clean the exterior of the product with a damp cloth.
3.Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
4.Scrape debris away from air intake vents on both sides
of the motor housing.
NOTICE:
Keeping air intake vents free of grass and debris
prevents motor overheating and possible failure.
Servicing the Product
Check and tighten all fasteners. If any part is damaged or
lost, repair it or replace it.
Checking the Fuel Cap, Tank, and
Lines
WARNING:
Check for fuel leaks. A leaking fuel cap, tank,
or lines are a re hazard and must be replaced
immediately. If you nd any leaks, correct the
problem before using the product. Failure to do
so could result in a re that could cause serious
personal injury.
The fuel cap contains a non-serviceable lter and check
valve. A clogged fuel lter causes poor engine performance.
If performance improves when the fuel cap is loosened,
the check valve may be faulty or the lter may be clogged.
Replace the fuel cap if necessary.
Maintenance
Normal maintenance, replacement or repair of emission con-
trol devices and systems may be performed by any qualied
repair establishment or individual with original or equiva-
lent parts. Warranty and recall repairs must be performed
by an authorized service center; please contact customer
service for assistance.
WARNING:
Before inspecting, cleaning, or servicing the
machine, shut o engine, wait for all moving
parts to stop, and disconnect spark plug wire
and move it away from spark plug. Failure to
follow these instructions can result in serious
personal injury or property damage.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1, along with
hearing protection. Failure to do so could result
in objects being thrown into your eyes and other
possible serious injuries.
WARNING:
Use only Toro replacement parts when servicing
this product. Use of any other parts could create
a hazard or cause product damage.
NOTICE:
Periodically inspect the entire product for dam-
aged, missing, or loose parts such as screws,
nuts, bolts, caps, etc. Tighten securely all fasten-
ers and caps and do not operate this product
until all missing or damaged parts are replaced.
Please contact customer service or a qualied
service center for assistance.
General Maintenance
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, lubricant, grease, etc.
19
Maintenance
Cleaning Air Filter
See Figure 16.
A wet or dirty air lter can aect the way the engine starts,
performs, and wears. The air lter should be checked and
cleaned after 5 hours of operation. Inspect and clean more
frequently if used in dusty dirty conditions.
For best performance, the air lter should be replaced every
25 hours or yearly.
To clean the air filter:
1. Depress air lter cover tab using a straight screwdriver
to open the air lter cover.
2. Remove the cover.
3. Lift the edge of the air lter carefully and peel it out.
4. Wash the air lter with warm, soapy water.
5. Rinse and squeeze to dry.
6. To reinstall the air lter cover, insert the tabs into the
notches and lock into place.
Note: Make sure the lter is seated properly inside the
cover. Installing the lter incorrectly will allow dirt to
enter the engine, causing rapid engine wear.
Air Filter
Air Filter
Cover
Figure 16
Air Filter
CoverTab
Figure 17
Spark
Plug Boot
Spark
Plug
Note: Depending on the type of fuel used, the type and
amount of lubricant used, and/or your operating conditions,
the exhaust port, muer, and/or spark arrestor screen may
become blocked with carbon deposits. If you notice a power
loss with your gas powered tool, you may need to remove
these deposits to restore performance. We highly recom-
mend that only qualied service technicians perform this
service.
Vacuum Bag
A dirty bag will reduce performance. To clean the bag, turn it
inside out and shake. Wash the bag in soapy water at least once
a year. Replacement parts available online at www.toro.com.
Spark Plug Replacement
See Figure 17.
This engine uses a Champion RCJ6Y spark plug. Use a
recommended or equivalent replacement every 25 hours or
annually.
1. Remove the spark plug boot.
2. Loosen the spark plug by turning it counterclockwise
with a socket.
Cleaning the Exhaust Port, Muffler
and Spark Arrestor
NOTICE:
The spark arrestor on this product has not been
evaluated by the USDA Forest Service and
cannot be used on U.S. forest lands. In addition,
product users must comply with Federal, State,
and local re prevention regulations. Check
with appropriate authorities. Contact customer
service or a qualied service center to purchase
a replacement spark arrestor.
20
Maintenance
This Product Was Manufactured With A Catalyst Muffler
Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s origi-
nal emission level, please refer to the maintenance section below.
MAINTENANCE SCHEDULE
Inspect for Clean Clean or Replace Replace
Maintenance Damage Before Every Every 25 Hours Every
Part Each Use 5 Hours or Yearly 125 Hours
* CATALYTIC MUFFLER ASSEMBLY .................................................................................................................X
* AIR FILTER ASSY
includes:
Filter .......................................................................................X
* CARBURETOR ASSY
includes:
Gaskets .......................................... X
* FUEL TANK ASSY
includes:
Fuel Lines ...................................... X
Fuel Cap ........................................ X
Fuel Filter ...................................................................................................................... X
* IGNITION ASSY
includes:
Spark Plug ..................................................................................................................... X
*NOTICE: THE USE OF EMISSION CONTROL COMPONENTS OTHER THAN THOSE DESIGNED FOR THIS
UNIT IS A VIOLATION OF FEDERAL LAW.
3. Remove the spark plug.
4. Inspect the new spark plug. The spark plug must
be properly gapped and free of deposits in order to
ensure proper engine operation. The correct gap is
approximately 0.025 in. (0.64 mm). To widen gap, if
necessary, carefully bend the ground (top) electrode.
To lessen gap, gently tap ground electrode on a hard
surface.
5. Hand thread the new spark plug into the cylinder , turn-
ing it clockwise.
6. Tighten with a socket. (torque to 216 in.lb. [24.40 Nm]
minimum, 264 in.lb. [29.82 Nm] maximum.) Do not
over-tighten.
NOTICE:
Be careful not to cross-thread the spark plug.
Cross-threading will seriously damage the
product.
Storing the Product
1. Clean all foreign material from the product. Store unit
indoors in a dry, well-ventilated area that is inaccessible
to children. Keep away from corrosive agents such as
garden chemicals, fertilizer, and de-icing salts.
2. Abide by all ISO and local regulations for the safe stor-
age and handling of gasoline.
When storing 1 month or longer:
1. Drain all fuel from tank into a container approved for
gasoline.
2. Run engine until it stops.
3. Place choke lever in the FULL CHOKE position.
4. Pull throttle lock back to lock the throttle.
5. Attempt to start the engine ve (5) more times.
High Altitude Engine Operation:
Your engine is congured for operation below 2000 feet
altitude at the factory. Your engine must be re-congured
for operation above 2000 feet altitude. Operating the engine
with the wrong engine conguration at a given altitude may
increase its emissions, decrease fuel eciency, degrade
performance and cause irreversible damage. Engines
congured for high altitude operation cannot be operated
in standard altitude conditions. A qualied service center
should ensure that your engine is properly congured for
your location.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Toro 51988 Manuel utilisateur

Catégorie
Souffleurs / sécheurs d'air
Taper
Manuel utilisateur

dans d''autres langues