Fortinet 124dpoe Manuel utilisateur

Marque: Fortinet

Modèle: 124dpoe

Taper: Manuel utilisateur

Ce manuel convient également à

Switch 124dpoe

FortiSwitch 124D-POE

QuickStart Guide

June 11, 2015

11-520-258883-20150611

FortiCare® and FortiGuard®, and certain other marks are registered

trademarks of Fortinet, Inc., in the U.S. and other jurisdictions, and

other Fortinet names herein may also be registered and/or common

law trademarks of Fortinet. All other product or company names may

be trademarks of their respective owners. Performance and other

metrics contained herein were attained in internal lab tests under ideal

conditions, and actual performance and other results may vary. Network

variables, different network environments and other conditions may affect

performance results. Nothing herein represents any binding commitment by

Fortinet, and Fortinet disclaims all warranties, whether express or implied,

except to the extent Fortinet enters a binding written contract, signed by

Fortinet’s General Counsel, with a purchaser that expressly warrants that

the identiﬁed product will perform according to certain expressly-identiﬁed

performance metrics and, in such event, only the speciﬁc performance

metrics expressly identiﬁed in such binding written contract shall be

binding on Fortinet. For absolute clarity, any such warranty will be limited

to performance in the same ideal conditions as in Fortinet’s internal lab

tests. In no event does Fortinet make any commitment related to future

deliverables, features or development, and circumstances may change

such that any forward-looking statements herein are not accurate. Fortinet

disclaims in full any covenants, representations, and guarantees pursuant

hereto, whether express or implied. Fortinet reserves the right to change,

modify, transfer, or otherwise revise this publication without notice, and the

most current version of the publication shall be applicable.

QuickStart Guide

• Technical Support

• New product features

• Protection from new threats

Vous devez enregistrer le produit pour recevoir:

• Support technique

• Nouvelles fonctionnalitées du produit

• Protection contre de nouvelles menaces

La reistrazione ti permette di usufruire di:

• Supporto Tecnico

• Nuove funzionalita

• Proteezione dalle ultime minaccce

Debe registrar el producto para recibir:

• Apoyo técnico

• Nuevas funcionalidades del producto

• Protección contra ataques

登録のお願い

本日、フォーティネット製品の登録をしてください。

登録すると次のメリットがあります。

テクニカルサポート • 新機能の追加 • 新しい脅威への防御

请马上注册

您的飞塔产品

您在注册以后才能得到技术支持、新产品特点信息、最新威胁防护

https://support.fortinet.com

Toll free: 1 866 648 4638

Phone: 1 408 486 7899

Fax: 1 408 235 7737

Email: [email protected]

Box Includes

Power Cable Console Cable

4 Rubber Feet

2 Rack-Mount Brackets

8 Bracket Screws

FortiSwitch 124D-POE

QuickStart Guide

QuickStart GuideFortiSwitch 124D-POE

Before You Begin

Write down details that you may need from your network administrator or ISP.

DSL PPPoE

Username Password

Cable Modem DHCP

It is normal to not require a hostname, but your ISP may require it.

Hostname

Static IP address

IP Address Subnet Mask

Default Gateway Primary/Secondary DNS

QuickStart Guide Video

http://video.fortinet.com/video/38/fortigate-and-fortiwiﬁ-quick-start-guide-5-0

Basic Connections

Connect your device to a power outlet and an Internet connection. This is usually a

modem, but could also be another device on your network.

Power Connection

Ethernet Port

Internet

Setup Options

Web Browser

Setup Wizard (p.7)

Terminal Emulation

With console cable (p.8)

MGMT Port

https://

Web Browser with Ethernet cable

To Connect to the GUI

1. Connect an Ethernet cable.

2. Conﬁgure the management computer to be on the same subnet as the internal

interface as the FortiSwitch unit:

IP address: 192.168.1.XXX

Netmask: 255.255.255.0

3. Visit https://192.168.1.99 in your web browser.

4. Login using username “admin” and no password.

5. Conﬁgure your device and save your settings.

6. Register your device from the dashboard page.

To Connect to the CLI

1. Connect the device’s console port to the management computer using the provided

console cable.

2. Start a terminal emulation program on the management computer, select the

COMport, and use the following settings:

Baud Rate: 115200

Data bits: 8

Parity: None

Stop bits: 1

Flow Control: None

3. Press Enter on your keyboard to connect to the CLI.

4. Login using username “admin” and no password. You can now proceed with

conﬁguring your device.

Get started by typing “?” for a list of available commands.

Begin typing a command then type “?” for a list of available ways to complete.

For example “conﬁg ?” will show the lowest level of conﬁguration options.

Terminal Emulation with Console

Cable

Console Port

Serial Port

1010

To install the FortiSwitch unit into a rack

1. Ensure that the FortiSwitch unit is placed on a stable

surface prior to rack-mount installation.

2. Attach the provided rack-mount brackets to the sides of

the unit using the provided bracket screws.

3. Position the FortiSwitch unit in the rack. Ensure there is

enough room around the unit to allow for sufﬁcient air

ﬂow.

Installation

Caution:

Electrostatic

discharge (ESD)

can damage

your Fortinet

equipment.

Do not place

heavy objects on

the unit.

To avoid personal

injury or damage

to the unit, it is

recommended

that two or more

people install the

unit into the rack.

Note: If the unit

has a redundant

power supply,

each power

cable should be

connected to a

different power

source. In this

way, if one power

source fails, the

other may still be

operational and

the unit will not

lose power.

The FortiSwitch unit can be placed on any ﬂat surface, or mounted in any standard

19 inch rack unit with the provided rack-mount brackets and screws.

Please read the Cautions and Warnings section prior to installing your device.

4. Line up the rack-mount bracket holes to the holes on the rack and ensure that the

FortiSwitch unit is level.

5. Finger tighten four rack-mount screws to attach the unit to the rack.

6. Verify that the spacing around the FortiSwitch unit conforms to requirements and that

the unit is level, then tighten the rack-mount screws with an appropriate screwdriver.

7. Using the provided power cable, plug the cable into the rear of the unit, and then into

a grounded electrical outlet or a separate power source such as an uninterruptible

power supply (UPS) or a power distribution unit (PDU).

To install the unit on a at surface

1. Ensure that the surface onto which the FortiSwitch unit to be installed is clean, level,

and stable and that there is at least 1.5in (3.8cm) of clearance on all sides to allow

for adequate airﬂow.

2. Attach the provided rubber feet to the bottom of the FortiSwitch unit.

3. Place the unit in the designated location.

4. Verify that the spacing around the FortiSwitch unit conforms to requirements and that

the unit is level.

5. Using the provided power cable, plug the cable into the rear of the unit, and then into

a grounded electrical outlet or a separate power source such as an uninterruptible

power supply (UPS) or a power distribution unit (PDU).

1.5in

1212

To install the SFP transceivers

1. Ensure that you are properly grounded.

2. Remove the caps from the SFP cage sockets on the

front panel of the unit.

3. Position the SFP transceiver in front of the cage socket

opening and ensure that the transceiver is correctly

oriented. When the transceiver is correctly oriented, the

extraction lever will be level with the socket latch.

Note: SFP cage socket orientation may vary. Ensure that

the SFP transceiver module is correctly oriented each

time that you are inserting a transceiver.

4. Hold the sides of the SFP transceiver and slide it into the

cage socket until it clicks into place.

Caution: SFP

transceivers are

static sensitive

devices. Use

an ESD wrist

strap or similar

grounding device

when handling

transceivers.

Do not install

or remove SFP

transceivers while

ﬁber-optic cables

are still attached.

This can cause

damage to the

cables, cable

connectors,

and the optical

interfaces. It may

also prevent the

transceiver from

latching correctly

into the socket

connector.

Note: Installing

and removing

SFP transceivers

can shorten their

useful life. Do not

install or remove

transceivers more

than is necessary.

SFP Transceivers

SFP Cage Sockets

Socket Latch

Transmit Optical Bore

Extraction Lever

Receive Optical Bore

5. Press the transceiver ﬁrmly into the cage socket with

your thumb.

6. Verify that the transceiver is latched correctly by grasping

the sides of the transceiver and trying to pull it out

without lowering the extraction lever.

If the transceiver cannot be removed, it is installed and

latched correctly.

If the transceiver can be removed, reinsert it and press

harder with your thumb.

If necessary, repeat this process until the transceiver is

securely latched into the cage socket.

To remove the SFP transceivers

1. Ensure that you are properly grounded.

2. If applicable, disconnect the ﬁber-optic cable from the

transceiver connector and install a clean dust plug in the

transceiver’s optical bores.

3. Pull the extraction lever out and down to eject the

transceiver. If you are unable to use your ﬁnger to open

the lever, use a small ﬂat-head screwdriver or other

similar tool to open the lever.

4. Hold the sides of the transceiver and carefully pull it away

from the cage socket.

5. Replace the cap on the SFP cage socket and place the

removed SFP transceiver into an antistatic bag.

Caution: Do not

force the SFP

transceivers into

the cage slots.

If the transceiver

does not easily

slide in and click

into place, it may

not be aligned

correctly or may

be upside down.

If this happens,

remove the SFP

transceiver, realign

it or rotate it and

slide it in again.

Note: Follow

proper ﬁber-

optic handling

procedures when

installing and

removing

SFP transceivers

to ensure the

devices remain

clean and are not

damaged.

1414

MGMT

Green: Connected

Flashing Green: Transmitting & receiving data

Off: No link established

Power

Green: The unit is on

Off: The unit is off

Alarm

Amber: The unit has a fault

Off: No faults detected

PoE MAX

Amber: Maximum output power budget reached

Off: Power available for new PD

RPS

Green: Power on and the RPS DC input is normal

Amber: RPS failure

Off: Power off, no connection

PoE Ports Link/Activity

Green: Connected

Flashing Green: Transmitting & receiving data

Off: No link established

PoE Ports Power

Amber: Providing power

Off: Not providing power

Device Guide

MGMT

SFP Ports

Green: Connected at 1Gbps

Flashing Green: Transmitting & receiving data

Off: No link established

Ethernet Ports Link/Activity

Green: Connected

Flashing Green: Transmitting & receiving data

Off: No link established

Ethernet Ports Speed

Green: Connected at 1Gbps

Amber: Connected at 100Mbps

Off: Connected at 10Mbps or not in use

1616

AC INPUT

100-240Vac

50-60Hz, 2.5A Max

+12V 14A

AND

-54V 7.8A

DC INPUT FOR REMOTE POWER SUPPLY SPECIFIED IN MANUAL

CONSOLE

MGMT

Console (RJ-45)

Optional connection to the

management computer

Provides access to the CLI

Ethernet Ports (RJ-45)

Gigabit Ethernet ports with smart Power over Ethernet

(PoE) providing up to a maximum of 100W for all ports

MGMT (RJ-45)

Client ports for management

Default IP address of MGMT 1 is 192.168.1.99

RPS

Optional connection for redundant power

12V DC, 14A and -54V DC, 7.8A

Device Guide

AC INPUT

100-240Vac

50-60Hz, 2.5A Max

+12V 14A

AND

-54V 7.8A

DC INPUT FOR REMOTE POWER SUPPLY SPECIFIED IN MANUAL

CONSOLE

MGMT

SFP Ports 25 and 26 (SFP)

1 Gbps small form-factor pluggable

transceiver ports

Ethernet Ports 13 to 24 (RJ-45)

Gigabit Ethernet ports for connection

to your network and the Internet

Power

100-240V AC, 50-60Hz, 2.5A Max

Cautions and Warnings

Environmental Specications

Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions:

Instructions de montage en rack - Les instructions de montage en rack suivantes ou similaires sont incluses avec les instructions d’installation:

Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be

greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient

temperature (Tma) specified by the manufacturer.

Température ambiante élevée – S’il est installé dans un rack fermé ou à unités multiples, la température ambiante de fonctionnement de l’environnement du

rack peut être supérieure à la température ambiante de la pièce. Par conséquent, il est important d’installer le matériel dans un environnement respectant la

température ambiante maximale (Tma) stipulée par le fabricant.

Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not

compromised.

Ventilation réduite – Installation de l’équipement dans un rack doit être telle que la quantité de flux d’air nécessaire au bon fonctionnement de l’équipement

n’est pas compromise.

Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

Chargement Mécanique – Montage de l’équipement dans le rack doit être telle qu’une situation dangereuse n’est pas lié à un chargement mécanique inégal.

Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits

might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this

concern.

Surtension – Il convient de prendre l’ensemble des précautions nécessaires lors du branchement de l’équipement au circuit d’alimentation et être

particulièrement attentif aux effets de la suralimentation sur le dispositif assurant une protection contre les courts-circuits et le câblage. Ainsi, il est

recommandé de tenir compte du numéro d’identification de l’équipement.

Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than

direct connections to the branch circuit (e.g. use of power strips).

Fiabilité de la mise à la terre– Fiabilité de la mise à la terre de l’équipement monté en rack doit être maintenue. Une attention particulière devrait être accordée

aux connexions d’alimentation autres que les connexions directes au circuit de dérivation (par exemple de l’utilisation de bandes de puissance).

Refer to specific Product Model Data Sheet for Environmental Specifications (Operating Temperature, Storage Temperature, Humidity, and Altitude).

Référez à la Fiche Technique de ce produit pour les caractéristiques environnementales (Température de fonctionnement, température de stockage, humidité

et l’altitude).

Safety

Battery – Risk of explosion if the battery is replaced by an incorrect type. Do not dispose of batteries in a fire. They may explode. Dispose of used batteries

according to your local regulations. IMPORTANT: Switzerland: Annex 4.10 of SR814.013 applies to batteries.

Batterie – Risque d’explosion si la batterie est remplacée par un type incorrect. Ne jetez pas les batteries au feu. Ils peuvent exploser. Jetez les piles usagées

conformément aux réglementations locales. IMPORTANT: Suisse: l’annexe 4.10 de SR814.013 s’appliquent aux batteries.

警告

本電池如果更換不正確會有爆炸的危險

請依製造商說明書處理用過之電池

Caution: This equipment is to be used in a Network Environment 0 per IECTR 62101. This product is connected only to PoE networks without routing to the

outside plant.

Attention: Ce matériel doit être utilisé dans un Environnement Réseau 0 par IECTR 62101. Ce produit est uniquement connecté aux réseaux PoE sans

installation externe de routage.

The RPS connection is intended to be connected to the power source from Fortinet IEC certified/UL Listed equipment. The power rating of the product must

be less than or equal to the output rating of the power source.

La connexion de RPS est destiné à être relié à la source de Fortinet CEI de matériel homologué / Listé UL puissance. La puissance nominale du produit doit

être inférieure ou égale à la puissance nominale de sortie de la source d’alimentation.

Regulatory Compliance

Federal Communication Commission (FCC) – USA

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received; including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be

required to correct the interference at his own expense.

WARNING: Any changes or modifications to this product not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment

Industry Canada Equipment Standard for Digital Equipment (ICES) – Canada

CAN ICES-3 (A) / NMB-3 (A)

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regula¬tions of the

Canadian Department of Communications.

Cet appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le

Règlement sur le brouillage radioélectrique édicte par le ministère des Communications du Canada.

European Conformity (CE) - EU

This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate

measures.

Voluntary Control Council for Interference (VCCI) – Japan

この装置は、クラスＡ情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがあります。この場合には使用者が適切な対策を講ず

るよう要求されることがあります。ＶＣＣＩ－Ａ

Bureau of Standards Metrology and Inspection (BSMI) – Taiwan

這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會被要求採取某些適當的對策。

China

此为A级产品，在生活环境中，该产品可能会造成无线电干扰。这种情况下，可能需要用户对其采取切实可行的措施。

Fortinet Product License Agreement / EULA and Warranty Terms

Trademarks and Copyright Statement

Fortinet®, FortiGate®, and FortiGuard® are registered trademarks of Fortinet, Inc., and other Fortinet names herein may also be trademarks, registered or otherwise, of Fortinet. All

tinet without prior notice. No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation

without permission from Fortinet, Inc., as stipulated by the United States Copyright Act of 1976.

Product License Agreement

The parties to this agreement are you, the end customer, and either (i) where you have purchased your Product within the Americas, Fortinet, Inc., or (ii) where you have purchased

your Product outside of the Americas, Fortinet Singapore Private Limited (each referred to herein as “Fortinet”) .CAREFULLY READ THE FOLLOWING LEGAL AGREEMENT (THE OR THIS

“AGREEMENT” OR “EULA”). USE OF FORTINET PRODUCT(S) AND ANY UPDATES THERETO, INCLUDING HARDWARE APPLIANCE PRODUCTS, SOFTWARE AND FIRMWARE INCLUDED

THEREIN BY FORTINET, AND STAND-ALONE SOFTWARE PRODUCTS SOLD BY FORTINET (TOGETHER, THE “PRODUCTS”) CONSTITUTES ACCEPTANCE BY YOU OF THE PROVISIONS IN

THIS AGREEMENT. FORTINET SHALL NOT BE BOUND BY ANY ADDITIONAL AND/OR CONFLICTING PROVISIONS IN ANY ORDER, RELEASE, ACCEPTANCE OR OTHER WRITTEN CORRE-

SPONDENCE OR OTHER WRITTEN OR VERBAL COMMUNICATION UNLESS EXPRESSLY AGREED TO IN A WRITING SIGNED BY THE GENERAL COUNSEL OF FORTINET. YOUR INSTALLATION

OR USE OF ANY PRODUCT REPRESENTS AGREEMENT TO THE TERMS HEREIN, AS AMENDED OR UPDATED FROM TIME TO TIME IN FORTINET’S DISCRETION BY FORTINET PUBLISHING

AN AMENDED OR UPDATED VERSION. IF YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS AGREEMENT, DO NOT START THE INSTALLATION PROCESS OR USE THE PRODUCTS. IF

YOU DO NOT AGREE TO THE PROVISIONS OF THIS AGREEMENT, YOU SHOULD IMMEDIATELY, AND IN NO EVENT LATER THAN FIVE (5) CALENDAR DAYS AFTER YOUR RECEIPT OF THE

PRODUCT RETURN THE PRODUCTS TO THE LOCATION WHERE YOU OBTAINED THEM FOR A FULL REFUND FROM THE PARTNER SELLING TO YOU.

1. License Grant.

This is a license, not a sales agreement, between you and Fortinet. The term “Software”, as used throughout this Agreement, includes all Fortinet and third party rmware and software

provided to you with, or incorporated into, Fortinet appliances and any stand-alone software provided to you by Fortinet, with the exception of any open source software contained

in Fortinet’s Products which is discussed in detail in section 15 below, and the term “Software” includes any accompanying documentation, any updates and enhancements of the

software or rmware provided to you by Fortinet, at its option. Fortinet grants to you a non-transferable (except as provided in section 5 (“Transfer”) and section 15 (“Open Source

Software”) below), non-exclusive, revocable (in the event of your failure to comply with these terms or in the event Fortinet is not properly paid for the applicable Product) license to

use the Software solely for your internal business purposes (provided, if a substantial portion of your business is to provide managed service provider services to your end-customers,

you may use the Software embedded in FortiGate and supporting hardware appliances to provide those services, subject to the other restrictions in this Agreement), in accordance

with the terms set forth in this Agreement and subject to any further restrictions in Fortinet documentation, and solely on the Fortinet appliance, or, in the case of blades, CPUs or da-

tabases, on the single blade, CPU or database on which Fortinet installed the Software or, for stand-alone Software, solely on a single computer running a validly licensed copy of the

operating system for which the Software was designed, or, in the case of blades, CPUs or databases, on a single blade, CPU or database. For clarity, notwithstanding anything to the

contrary, all licenses of Software to be installed on blades, CPUs or databases are licensed on a per single blade, solely for one blade and not for multiple blades that may be installed

in a chassis, per single CPU or per single database basis, as applicable. The Software is “in use” on any Fortinet appliances when it is loaded into temporary memory (i.e. RAM). You

agree that, except for the limited, specic license rights granted in this section 1, you receive no license rights to the Software.

2. Limitation on Use.

You may not attempt to, and, if you are a corporation, you are responsible to prevent your employees and contractors from attempting to, (a) modify, translate, reverse engineer,

decompile, disassemble, create derivative works based on, sublicense, or distribute the Software; (b) rent or lease any rights in the Software in any form to any third party or make the

Software available or accessible to third parties in any other manner; (c) except as provided in section 5, transfer assign or sublicense right to any other person or entity, or (d) remove

any proprietary notice, labels, or marks on the Software, Products, and containers.

3. Proprietary Rights.

All rights, title, interest, and all copyrights to the Software and any copy made thereof by you and to any Product remain with Fortinet. You acknowledge that no title to the intellectual

property in the Software or other Products is transferred to you and you will not acquire any rights to the Software or other Products except for the specic license as expressly set

forth in section 1 (“License Grant”) above.

4. Term and Termination.

Except for evaluation and beta licenses or other licenses where the term of the license is limited per the evaluation/beta or other agreement or in the ordering documents, the term of

the license is for the duration of Fortinet’s copyright in the Software. Fortinet may terminate this Agreement, and the licenses and other rights herein, immediately without notice if you

breach or fail to comply with any of the terms and conditions of this Agreement. You agree that, upon such termination, you will cease using the Software and any Product and either

destroy all copies of the Fortinet documentation or return all materials to Fortinet. The provisions of this Agreement, other than the license granted in section 1 (“License Grant”), shall

survive termination.

5. Transfer.

If you are a Fortinet contracted and authorized reseller or distributor of Products, you may transfer (not rent or lease unless specically agreed to in writing by Fortinet) the Software

to one end user on a permanent basis, provided that: (i) you ensure that your customer and the end user receives a copy of this Agreement, is bound by its terms and conditions,

and, by selling the Product or Software, you hereby agree to enforce the terms in this Agreement against such end user, (ii) you at all times comply with all applicable United States

export control laws and regulations, and (iii) you agree to refund any fees paid to you by an end user who purchased Product(s) from you but does not agree to the terms contained

in this Agreement and therefore wishes to return the Product(s) as provided for in this Agreement. Further, if you are a non-authorized reseller of Products, you are not authorized to

sell Product(s) or Software, but, regardless, by selling Product(s) or Software, you hereby agree you are bound by the restrictions and obligations herein and are bound to: (i) ensure

that your customer and the end user receive a copy of this Agreement and are bound in full by all restrictions and obligations herein (ii) enforce the restrictions and obligations in this

Agreement against such customer and/or end user, (iii) comply with all applicable United States export control laws and regulations and all other applicable laws, and (iv) refund any

fees paid to you by a customer and/or end user who purchased Product(s) from you but does not agree to the restrictions and obligations contained in this Agreement and therefore

wishes to return the Product(s) as provided for in this Agreement. Notwithstanding anything to the contrary, distributors, resellers and other Fortinet partners (a) are not agents of

Fortinet and (b) are not authorized to bind Fortinet in any way.

6. Limited Warranty.

Fortinet provides this limited warranty for its product only to the single end-user person or entity that originally purchased the Product from Fortinet or its authorized reseller or distrib-

utor and paid for such Product. The warranty is only valid for Products which are registered on Fortinet’s Support Website: https://support.fortinet.com; or on the TalkSwitch support

website: http://global.talkswitch.com; or such other website as provided by Fortinet. For the below software warranty to start, registration must take place within three hundred

sixty-ve (365) days from the date the Product was originally shipped from Fortinet’s facilities or the warranty is null and void and will not be honored. For the hardware warranty, such

warranty starts on the earlier of the date of Product registration on Fortinet’s Support Website or ninety (90) days from the date that the Product was originally shipped from Fortinet’s

facilities. It is the Fortinet distributor’s and reseller’s responsibility to make clear to the end user the date the product was originally shipped from Fortinet, and it is the end user’s

responsibility to understand the original ship date from the party from which the end user purchased the product. All warranty claims must be submitted in writing to Fortinet before

the expiration of the warranty term or such claims are waived in full, i.e. ninety (90) days from the earlier of registration or the automatically started term for hardware and spare parts

claims and three hundred sixty-ve (365) days from registration within three hundred sixty-ve (365) days from shipment for software claims. Fortinet provides no warranty for any

beta, donation or evaluation Products, for any spare parts not purchased directly from Fortinet by the end-user, for any accessories, or for any stand-alone software.

Fortinet warrants that the hardware portion of the Products, including spare parts unless noted otherwise (“Hardware”) will be free from material defects in workmanship as compared

to the functional specications for the period set forth as follows and applicable to the Product type (“Hardware Warranty Period”): a three hundred sixty-ve (365) day limited

warranty for the Hardware excluding spare parts, , power supplies, and accessories (provided, solely with respect to FortiAP indoor Wi-Fi access point Hardware appliance products

and FortiSwitch Hardware appliance products other than the FortiSwitch-5000 series (for both excluding spare parts, power supplies, and accessories), the warranty herein shall last

from the start of the warranty period as discussed above until ve (5) years following the product announced end-of-life date), and, for spare parts, power supplies, and accessories,

solely a ninety (90) days limited warranty. Fortinet’s sole obligation shall be to repair or replace the defective Hardware at no charge to the original owner. This obligation is exclusive of

transport fees, labor or installation costs, and any other cost which are not directly associated to the Product. Such repair or replacement will be rendered by Fortinet at an authorized

Fortinet service facility as determined by Fortinet. The replacement Hardware need not be new or of an identical make, model, or part; Fortinet may, in its discretion, replace the defec-

tive Hardware (or any part thereof) with any reconditioned Product that Fortinet reasonably determines is substantially equivalent (or superior) in all material respects to the defective

Hardware. The Hardware Warranty Period for the repaired or replacement Hardware shall be for the greater of the remaining Hardware Warranty Period or ninety days from the delivery

of the repaired or replacement Hardware. If Fortinet determines in its reasonable discretion that a material defect is incapable of correction or that it is not practical to repair or replace

defective Hardware, the price paid by the original purchaser for the defective Hardware will be refunded by Fortinet upon return to Fortinet of the defective Hardware. All Hardware (or

part thereof) that is replaced by Fortinet, or for which the purchase price is refunded, shall become the property of Fortinet upon replacement or refund.

Fortinet warrants that the software portion of Hardware Products will substantially conform to Fortinet’s then current functional specications for the Software, as set forth in the

applicable documentation for a period of ninety (90) days (“Software Warranty Period”), if the Software is properly installed on approved Hardware and operated as contemplated in

its documentation. Fortinet’s sole obligation shall be to repair or replace the non-conforming Software with software that substantially conforms to Fortinet’s functional specications.

Except as otherwise agreed by Fortinet in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted

by Fortinet for the Software. The Software Warranty Period shall extend for an additional ninety (90) days after any replacement software is delivered. If Fortinet determines in its rea-

sonable discretion that a material non-conformance is incapable of correction or that it is not practical to repair or replace the non-conforming Software, the price paid by the original

licensee for the non-conforming Software will be refunded by Fortinet; provided that the non-conforming Software (and all copies thereof) is rst returned to Fortinet. The license

granted respecting any Software for which a refund is given automatically terminates immediately upon refund. For purpose of the above hardware and software warranties, the term

“functional specications” means solely those specications authorized and published by Fortinet that expressly state in such specications that they are the functional specications

referred to in this section 6 of this Agreement, and, in the event no such specications are provided to you with the Software or Hardware, there shall be no warranty on such Software.

7. Disclaimer of Other Warranties and Restrictions.

La page charge ...