Miele 41BAN045USA Manuel utilisateur

Catégorie
Aspirateurs
Taper
Manuel utilisateur
en Operating Instructions Canister Vacuum Cleaner
fr Mode d'emploi Aspirateur-chariot
SCAE0
M.-Nr. 10 847 150
HS10
2
en ....................................................................................................................... 5
fr ......................................................................................................................... 28
3
Only Miele FilterBags, filters and accessories with
the "Original Miele" logo can be used with this
vacuum. Only then can the suction power of the
vacuum cleaner reach its optimum potential creating
the best possible cleaning results.
USE OF NON-MIELE COMPONENTS MAY VOID
THE WARRANTY.
,
The use of FilterBags made of paper or a similar
material, or FilterBags with a cardboard retaining
plate can lead to serious damage to the vacuum
cleaner and may void the warranty, just as with the
use of FilterBags without the "Original Miele" logo.
The "Original Miele" Logo will appear on the
packaging or directly on the FilterBag.
Purchasing new FilterBags and filters
Original Miele FilterBags and filters can be purchased
from an authorized Miele vacuum dealer or by visiting the
Miele store at www.mieleusa.com.
en - Contents
4
IMPORTANT SAFETY INSTRUCTIONS ................................................................ 5
Appliance description ......................................................................................... 10
Caring for the environment ................................................................................ 12
References to illustrations.................................................................................. 13
Preparing for use................................................................................................. 13
Use........................................................................................................................ 15
Parking, transport and storage .......................................................................... 16
Maintenance ........................................................................................................ 16
Purchasing new FilterBags and filters ................................................................... 17
Ordering the correct FilterBags and filters ............................................................ 17
When to change the FilterBag .............................................................................. 17
How the FilterBag change indicator works ........................................................... 18
How to replace the FilterBag ................................................................................ 18
When to change the motor protection filter........................................................... 18
How to change the motor protection filter ........................................................... 18
When to replace the exhaust filter......................................................................... 19
How to replace the AirClean exhaust filter ........................................................... 19
Replacing the AirClean Plus 50, Active AirClean 50, and HEPA AirClean 50 ex-
haust filters ........................................................................................................... 19
Replacing one type of exhaust filter with another ................................................ 20
When to change the thread catchers? .................................................................. 20
How to replace the thread lifters .......................................................................... 20
Cleaning the roller on the AllTeQ floorhead .......................................................... 20
Cleaning and care ............................................................................................... 21
Frequently Asked Questions ..............................................................................22
Technical Service................................................................................................. 23
Contact in case of fault ......................................................................................... 23
Warranty ................................................................................................................ 23
Optional accessories .......................................................................................... 23
Limited Warranty - Vacuum Cleaners USA ....................................................... 25
en - IMPORTANT SAFETY INSTRUCTIONS
5
This vacuum cleaner complies with current safety re-
quirements. Inappropriate use can, however, lead to per-
sonal injury and damage to property.
To avoid the risk of accidents and damage to the vacuum
cleaner, please read the operating instructions carefully
before using it for the first time. They contain important
information on its safety, operation and maintenance.
Keep these operating instructions in a safe place and
pass them on to any future user.
Always disconnect the vacuum cleaner from the power
supply when you have finished using it, before changing
any accessories, as well as for maintenance work and
cleaning. Turn the vacuum cleaner off and unplug it.
Correct use
This vacuum cleaner is intended for cleaning flooring in
domestic households and similar residential environments.
This vacuum cleaner can be used for all normal cleaning
of carpets, rugs and hard flooring.
This vacuum cleaner is not intended for outdoor use.
This vacuum cleaner is intended for use at altitudes of
up to 1300ft (4000m) above sea level.
The vacuum cleaner must only be used to vacuum dry
floor surfaces. Do not use on people and animals. Any
other usage, modification or alteration is not supported by
the manufacturer and could be dangerous.
en - IMPORTANT SAFETY INSTRUCTIONS
6
Persons which lack physical, sensory or mental abilities
or experience with the machine should not use it without
supervision or instruction by a responsible person.
Safety with children
Danger of suffocation! Ensure that any plastic wrap-
pings, bags, etc. are disposed of safely and kept out of the
reach of children.
Do not allow the vacuum cleaner to be used as a toy.
Close attention is necessary when used near children.
Technical safety
Before using the vacuum cleaner and its accessories,
check for any visible signs of damage. Do not use a dam-
aged appliance.
Ensure that the connection data on the data plate of the
vacuum cleaner (voltage and frequency) match the house-
hold power supply. Without modifications, the vacuum
cleaner is suited for 50Hz or 60Hz.
The electrical outlet must be fitted with a 15 A fuse.
Reliable and safe operation of this vacuum cleaner can
only be assured if it has been connected to the electricity
supply.
Repairs must only be performed by an authorized ser-
vice agent in accordance with national and local safety
regulations. Unauthorized repairs could cause injury or ma-
chine damage. Otherwise the warranty will be void.
en - IMPORTANT SAFETY INSTRUCTIONS
7
Do not pull or carry the vacuum cleaner by the power
cord, and be careful not to damage the cord when with-
drawing the plug from the socket. Keep the cord away
from sharp edges and do not let it get pinched, for exam-
ple, under a door. Avoid running the vacuum cleaner over
the cord. This could damage the cord, plug or socket. The
appliance must not be used if any of these have suffered
damage.
Do not use the vacuum cleaner if the power cord is
damaged. If the power cord is damaged it must be re-
placed together with the cord reel. For safety reasons this
must only be done by Miele Technical Service or a Miele
authorized service technician.
When vacuuming, in particular fine dust, e.g. sawdust,
sand, plaster, flour, talcum powder etc., electrostatic
charges build up naturally. Under certain conditions these
charges will be released. To avoid the unpleasant effects of
these discharges, a metal inlay has been incorporated into
the underside of the handle. Please make sure that you
keep your hand in constant contact with this metal strip
during vacuuming.
Do not let the vacuum cleaner get wet. Clean only with a
dry cloth or slightly damp cloth when disconnected from
the electrical supply.
Repairs should only be carried out by a Miele-authorized
service technician. Repairs and other work by unqualified
persons can cause considerable danger to users.
en - IMPORTANT SAFETY INSTRUCTIONS
8
Defective components should be replaced by Miele orig-
inal parts only. Only with these parts can the manufacturer
guarantee the safety of the appliance.
Proper use
To avoid the risk of damage, do not use the vacuum
cleaner without the FilterBag, dust compartment filter and
exhaust filter in place.
The dust compartment cover will not close without a Fil-
terBag inserted. Do not force it.
Do not vacuum up anything which has been burning or
smoking, e.g., cigarettes, ashes or hot ash, whether glow-
ing or apparently extinguished.
Do not use the vacuum cleaner to vacuum up any water,
liquid or damp dirt. Wait until any freshly cleaned or sham-
pooed rugs or carpets are completely dry before attempt-
ing to vacuum.
Do not use the vacuum cleaner to vacuum toner dust.
Toner, such as that used in printers and photocopiers, can
conduct electricity.
Do not vacuum up any flammable or combustible liquids
or gases and do not vacuum in areas where such sub-
stances are stored.
Do not vacuum at head height and do not let the suction
get anywhere near a person's head.
en - IMPORTANT SAFETY INSTRUCTIONS
9
Accessories
To avoid the risk of injury when vacuuming with a Miele
turbobrush, do not touch the rotating roller brush.
It is not advisable to vacuum directly with the handle,
i.e., without an accessory attached, as the rim could get
damaged and you could hurt yourself on sharp edges.
Only use genuine FilterBags, filters and accessories with
the "Original Miele" logo on them. Otherwise the manufac-
turer cannot guarantee the safety of the product.
SAVE THESE INSTRUCTIONS
en - Appliance description
10
en - Appliance description
11
a
Handle
b
Air inlet valve
c
Release buttons
d
Accessories holder
e
Telescopic suction wand release button
f
Dust compartment lid release button
g
Telescopic suction wand
h
Original Miele filter bag
i
Carrying handle
j
Floorhead *
k
Park system for storage
l
Motor protection filter
m
Original Miele exhaust filter
n
Rotary selector
o
Power cord
p
Foot switch for automatic cord rewind
q
Park system for pauses during vacuuming
r
On/off foot switch
s
Filter bag change indicator
t
Connection socket
u
Suction hose
* These features are model-specific and may vary or may not be available on your
vacuum cleaner.
en - Caring for the environment
12
Disposal of the packing mate-
rial
The cardboard box and packing materi-
als protect the appliance during ship-
ping. They have been designed to be
biodegradable and recyclable.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children. Dan-
ger of suffocation!
Disposing of the FilterBags
and filters
Filterbags and filters are made from en-
vironmentally friendly materials, and can
be disposed of with the normal house-
hold waste, as long as they have been
used exclusively for general household
dust.
Disposing of your old appli-
ance
Before disposing of your old appliance
remove the FilterBag and filters and dis-
pose of them with your household
waste.
Electronic and electrical appliances
contain many valuable materials. They
also contain certain materials, com-
pounds and components which were
essential for their correct functioning
and safety. These could be hazardous
to your health and to the environment if
disposed of with general waste or if
handled incorrectly. Please do not,
therefore, dispose of your old appliance
with general waste.
Instead, please make use of officially
designated collection and disposal
points to dispose of and recycle electri-
cal and electronic appliances. By law,
you are solely responsible for deleting
any personal data from the appliance
prior to disposal. Please ensure that
your old appliance poses no risk to chil-
dren while being stored for disposal.
en-US
13
References to illustrations
The illustrations referred to in the text
are shown on the fold-out pages at
the end of these Operating Instruc-
tions.
Preparing for use
Attaching the suction hose (Fig. 01)
Insert the hose connector into the
suction socket on the vacuum
cleaner until it clicks into position.
Disconnecting the suction hose
(Fig. 02)
Press the release buttons at the side
of the hose connector, and lift the
hose from the socket.
Connect the suction hose to the han-
dle (Fig. 03)
Fit the connector at the other end of
the suction hose into the handle until
it clicks into position.
Connecting the handle to the wand
(Fig. 04)
Insert the handle into the wand until it
clicks into position. To do this, line up
the guides on the two pieces.
To release the handle from the wand,
press the release button and pull the
handle out of the wand, twisting it
slightly as you do so.
Adjusting the telescopic suction
wand (Fig. 05)
One part of the telescopic suction wand
is packed inside the other and it can be
adjusted to suit your height for comfort-
able vacuuming.
Press the release button and adjust
the telescopic suction wand to the re-
quired length.
Connect the suction wand to the
floorhead (Fig. 06)
Push the suction wand into the floor-
head and turn it clockwise or coun-
terclockwise until it clicks into posi-
tion.
To separate the suction wand from
the floorhead, press the release but-
ton and pull the suction wand away
from the floorhead, twisting it slightly
as you do so.
Adjusting the floorhead (Fig. 07 + 08)
(only for models with a reversible floor-
head included in the standard version)
This vacuum cleaner can be used for
the everyday cleaning of carpets, rugs
and hard flooring.
Miele offers a range of other floorheads,
brushes and accessories for other types
of flooring and special applications (see
"Optional accessories").
Please always follow the flooring
manufacturer's cleaning and care in-
structions.
Vacuum carpets and rugs with the
brush retracted:
Press the foot switch .
Clean hard flooring which is not sus-
ceptible to scratching, and flooring with
gaps or deep crevices in it with the
brush protruding:
Press the foot switch .
en-US
14
If the suction power of the floorhead
seems too high, reduce the suction
until the head is easier to maneuver
(see "Use - Regulating the suction
power").
Activating the TimeStrip® exhaust fil-
ter change indicator on the exhaust
filter
Depending on the model, your vacuum
cleaner will be fitted as standard with
one of the following exhaust filters (Fig.
09).
a AirClean
b AirClean Plus 50 (light blue)
c Active AirClean 50 (black)
d HEPA AirClean 50 (white)
If your vacuum cleaner is fitted with ex-
haust filter c or d, you need to activate
the TimeStrip® exhaust filter change in-
dicator.
Press the release button on the re-
cessed grip and raise the dust com-
partment lid as far as it will go (Fig.
10).
Remove the indicator strip (Fig. 11).
Press the TimeStrip® exhaust filter
change indicator(Fig. 12).
After approx. 10–15 seconds a thin red
line will appear in the left-hand side of
the display (Fig. 13).
Close the dust compartment lid se-
curely, making sure it clicks into posi-
tion. Take care not to trap the filter
bag when doing so.
How the TimeStrip® exhaust filter
change indicator works
The TimeStrip® exhaust filter change
indicator shows the remaining func-
tional life of the exhaust filter. After ap-
prox. 50 operating hours, or approx.
one year of average use, the display will
be completely filled with red (Fig. 14).
Using the accessories supplied
(Fig. 15 + 16)
Dusting brush
Upholstery nozzle
Crevice nozzle
Accessory holder for the three
accessories supplied
Symbols on the holder show where to
attach the different accessories.
Attach the accessories holder to the
top or bottom of the suction wand
when required (Fig. 16).
Some models are supplied as standard
with one of the following accessories
which are not illustrated.
AllergoTeQ floorhead
Turbobrush
These vacuum cleaners are supplied
with separate operating instructions for
the relevant accessory part.
Reversible floorhead (Fig. 17)
(included as standard depending on
model)
For general use and also for vacuuming
the stairs.
en-US
15
For safety reasons when vacu-
uming stairs, it is best to start at the
bottom of the stairs and move up-
wards.
Parquet floorbrush (SBB Parquet-3)
(included as standard depending on
model)
This brush has natural bristles and is
designed for use on smooth floors that
are susceptible to scratching.
Use
Unwinding the cord (Fig. 18)
Pull the power cord out to the re-
quired length (max. cord length ap-
prox. 18" (5.5 m).
Insert the plug into the socket.
If vacuuming for longer than 30
minutes, the cord must be pulled out
all the way. Danger of overheating
and damage.
Rewinding the power cord (Fig. 19)
Turn off at the wall socket and un-
plug.
Press the rewind foot control. The
cord will rewind automatically.
Turning the vacuum cleaner on and
off (Fig. 20)
Press the On/Off foot control .
Regulating the suction power
(Fig. 21)
The suction power can be regulated to
suit the type of flooring being cleaned.
Reducing the suction power reduces
the amount of effort required to maneu-
ver the floorhead.
The vacuum cleaner has symbols on
the controls which indicate the type of
use the settings are suitable for.
Curtains, fabrics
Upholstery, cushions
Deep pile carpets, rugs and run-
ners
Energy-saving normal vacuuming
with low noise
Low pile carpet and rugs
Hard flooring and heavily soiled
carpets and rugs
When using the adjustable floorhead,
if the suction seems too high, reduce
the suction until the floorhead is eas-
ier to maneuver.
Turn the suction power selector man-
ually to the suction power setting you
require.
Opening the air inlet valve (Fig. 22)
It is easy to reduce the suction power
for a short time, e.g., to prevent rugs or
other objects being sucked into the
vacuum cleaner.
Open the air inlet valve on the handle
far enough to reduce the suction
power.
en-US
16
This reduces the suction on the respec-
tive nozzle used.
During vacuuming
When vacuuming, pull the vacuum
cleaner behind you on its wheels. You
can stand it upright for vacuuming
stairs and curtains, etc.
When vacuuming, in particular
fine dust, e.g. dust, sand, plaster,
flour, etc., electrostatic charges build
up naturally. Under certain conditions
these charges will be released. To
avoid the unpleasant effects of these
discharges, a metal inlay has been
incorporated into the underside of
the handle. Please make sure that
you keep your hand in constant con-
tact with this metal strip during vacu-
uming (Fig. 23).
Parking, transport and storage
Park system for pauses during vacu-
uming (Fig. 24)
The Park system allows you to conve-
niently park the wand and floorhead
during short pauses in vacuuming.
Slot the floorhead into the parking at-
tachment on the vacuum cleaner.
If your vacuum cleaner is on a slop-
ing surface such as a ramp, fully re-
tract the telescopic wand fully.
Park system for storage (Fig. 25)
Always disconnect the vacuum
cleaner from the power supply when
you have finished using it. Remove
the plug from the socket.
Stand the vacuum cleaner upright.
It is a good idea to retract the tele-
scopic suction wand fully.
Slot the floorhead downwards into
one of the parking attachments on ei-
ther side of the vacuum cleaner (the
parking attachments cannot be used
with Electrobrushes SEB 217 and
SEB 228).
This makes the vacuum cleaner easier
to carry or store.
Maintenance
Always switch off the vacuum
cleaner for maintenance work and
remove the plug from the outlet.
The Miele filtration system consists of
three components:
Original Miele FilterBag
Motor protection filter
Original Miele exhaust filter
These will need to be replaced from
time to time to ensure that your vacuum
cleaner performs efficiently.
en-US
17
We recommend only using genuine
FilterBags, filters, and accessories
with the "Original Miele" logo on
them. This will ensure that the suc-
tion power of the vacuum cleaner is
maintained, giving the best possible
cleaning results.
FilterBags with the "Original Miele"
logo on them are not made from pa-
per or paper-based materials and nor
do they have a cardboard collar. This
is why our FilterBags are particularly
long-lasting and reliable.
Please note that appliance faults and
damage originating from the use of
accessories which do not carry the
"Original Miele" logo will not be cov-
ered by the appliance guarantee.
Purchasing new FilterBags and filters
Original Miele FilterBags and filters are
available from the Miele web store,
Miele Technical Service, and your Miele
dealer.
Ordering the correct FilterBags and
filters
Only use original Miele FJM FilterBags
with a red collar and original Miele fil-
ters. These are identified by the "ORIGI-
NAL Miele" logo on the packaging.
Every packet of original Miele FilterBags
contains four bags, one AirClean ex-
haust filter and one motor protection fil-
ter. Original Miele multipacks contain 16
FilterBags, four AirClean exhaust filters
and four motor protection filters.
Original Miele exhaust filters can also
be purchased separately from your
Miele dealer or Miele Technical Service.
Please quote the model number of your
vacuum cleaner when ordering to make
sure you get the correct filter. You can
also order all accessories via the Miele
web store.
When to change the FilterBag
(Fig. 26)
Change the FilterBag when the color
marker in the FilterBag change indicator
turns red.
FilterBags are disposable and in-
tended to be used only once. Dis-
pose of the entire FilterBag. Do not
attempt to re-use. Blocked pores re-
duce the efficiency of the vacuum
cleaner.
Checking the FilterBag change indi-
cator
Attach the standard adjustable floor-
head to the vacuum cleaner.
Switch the vacuum cleaner on and
select the highest power setting.
Lift the floorbrush off the floor a little.
en-US
18
How the FilterBag change indicator
works
The FilterBag change indicator is set for
normal household dust. This generally
contains a mixture of dust, hair,
threads, carpet lint, grit, etc.
However, if the cleaner has been used
to vacuum up fine dust, such as plaster,
brick dust, cement or flour, the pores of
the FilterBag will become blocked very
quickly.
This affects the air permeability of the
bag, and the marker will indicate that
the bag is "full" even when it is not. If
this happens you must still change the
FilterBag because suction power will be
greatly reduced by blocked pores in the
FilterBag.
If, on the other hand, a large amount of
hair and carpet lint which typically con-
tains a lot of air is vacuumed up, the in-
dicator may fail to react even though
the bag is full. You should still change it.
Both these extremes can occur.
How to replace the FilterBag
(Fig. 27 + 28)
Press the release catches at the side
of the hose connector, and remove
the hose from the socket (Fig. 02).
Press the release button on the re-
cessed grip and raise the dust com-
partment lid as far as it will go (Fig.
10).
The FilterBag has a flap which closes
automatically when the dust compart-
ment lid is raised to prevent any dust
escaping.
Pull the FilterBag out by the grip on
the collar.
Fit the new FilterBag into the holder
as far as it will go. Leave it folded up
when you take it out of the box.
Close the dust compartment lid se-
curely, making sure it clicks into posi-
tion. Take care not to trap the Fil-
terBag when doing so.
An empty operation lock prevents
the dust compartment lid from clos-
ing without a FilterBag in place. Do
not use force!
Insert the hose connector into the
suction socket on the vacuum
cleaner until it clicks into position
(Fig. 01).
When to change the motor protection
filter
Replace this filter every time you start a
new packet of filter bags.
Every packet of original Miele filter bags
contains a motor protection filter. Multi-
packs contain four motor protection fil-
ters.
How to change the motor protection
filter (Fig. 29)
Open the dust compartment lid.
Pull the filter bag out by the grip on
the collar.
Lift up the filter frame until it clicks
and remove the old motor protection
filter. Hold by the clean, unsoiled sec-
tion to remove it.
Replace with a new motor protection
filter.
Close the filter frame.
en-US
19
Fit the filter bag into the holder as far
as it will go.
Close the dust compartment lid se-
curely, making sure it clicks into posi-
tion. Take care not to trap the filter
bag when doing so.
When to replace the exhaust filter
Depending on the model, your vacuum
cleaner will be fitted as standard with
one of the following exhaust filters (Fig.
09).
a AirClean
Replace this filter every time you start a
new packet of filter bags. Every packet
of original Miele filter bags contains one
AirClean exhaust filter. Multipacks con-
tain four AirClean filters.
bAirClean Plus 50 (light blue)
Replace this filter after approx. one
year. Make a note of the date on the ex-
haust filter.
cActive AirClean 50 (black)
dHEPA AirClean 50 (white)
Replace this filter when the TimeStrip®
exhaust filter change indicator is com-
pletely red (Fig. 14). The indicator lights
up after approximately 50 operating
hours, which is equivalent to about a
year of average use. You can continue
vacuuming when the light comes on.
However, the suction power will be re-
duced as will the effectiveness of the fil-
ter.
How to replace the AirClean exhaust
filter (Fig. 30 + 31)
Do not use more than one exhaust fil-
ter at a time.
Open the dust compartment lid.
Open the filter grille.
Grasp the used AirClean exhaust filter
by the clean, unsoiled section and
take it out.
Replace it with a new AirClean ex-
haust filter.
If you wish to fit an AirClean Plus 50,
Active AirClean 50, or HEPA AirClean
50 exhaust filter, see "Replacing one
type of exhaust filter with another".
Close the filter grille.
Close the dust compartment lid.
Replacing the AirClean Plus 50,
Active AirClean 50, and
HEPA AirClean 50 exhaust filters
(Fig. 32 + 33)
Do not use more than one exhaust fil-
ter at a time.
en-US
20
Open the dust compartment lid.
Lift the exhaust filter and remove it.
Insert a new exhaust filter, making
sure it goes in properly, then push it
down into position.
If you are using exhaust filter c or d,
press the TimeStrip® exhaust filter
change indicator (Fig. 12).
After approx. 10–15 seconds, a thin red
line will appear in the left hand side of
the display for both exhaust filters (Fig.
13).
If you wish to fit the AirClean exhaust
filter, see "Replacing one type of ex-
haust filter with another".
Close the dust compartment lid.
Replacing one type of exhaust filter
with another (Fig. 09)
Depending on model, your vacuum
cleaner will be fitted as standard with
one of the following exhaust filters:
a AirClean
b AirClean Plus 50 (light blue)
c Active AirClean 50 (black)
d HEPA AirClean 50 (white)
Do not use more than one exhaust fil-
ter at a time.
When changing the filter please note
1. If you wish to replace exhaust filter a
with filter b, c, or d, it is essential that
you remove the filter grille before you
fit the new exhaust filter.
If you are using exhaust filter c or d,
you must also activate the
TimeStrip® exhaust filter change in-
dicator (Fig. 12).
2. If you wish to replace exhaust filter b,
c, or d with filter a, it is essential that
you also fit the filter grille * (Fig. 31).
* Filter grille – see "Optional acces-
sories"
When to change the thread catchers?
(only possible for models with a re-
versible floorhead included as standard)
The thread catchers on the suction inlet
of the reversible floorhead can be re-
placed. Check them from time to time
and replace them if the pile has worn
down.
How to replace the thread lifters
(Fig. 34 + 35)
Use a suitable screwdriver to remove
the thread lifters from the slots.
Fit new thread lifters.
Cleaning the roller on the AllTeQ
floorhead (Fig. 36)
Clean the roller on the floorhead if re-
quired.
Release the bearing using a coin.
Press the bearing out, and remove.
Remove the roller.
Remove any threads and hair, replace
the roller and refit the bearing, locking
it back into position.
Replacement parts are available from
your Miele dealer or through Miele
Technical Service.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Miele 41BAN045USA Manuel utilisateur

Catégorie
Aspirateurs
Taper
Manuel utilisateur

dans d''autres langues