Thermador PRD366JGU Guide d'installation

INSTALLATION MANUAL

For THERMADOR PROFESSIONAL

PRO GRAND

®

Dual Fuel Ranges

MANUEL D'INSTALLATION

Pour cuisinières mixtes PROFESSIONAL PRO

GRAND

mc

de THERMADOR

MANUAL DE INSTALACIÓN

Para estufas mixtas PROFESSIONAL PRO

GRAND

®

de THERMADOR

Models/

Modèles /

Modelos:

PRD36

PRD48

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Important Installation Information . . . . . . . . . . . . . . . . . . . . . 2

Step 1: Ventilation Requirements . . . . . . . . . . . . . . . . . . . . . . . 3

Step 2: Cabinet Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Step 3: Unpacking and Moving the Range . . . . . . . . . . . . . . . . 8

Step 4: Door Removal and Reinstallation . . . . . . . . . . . . . . . . 10

Step 5: Installing Anti-Tip Device . . . . . . . . . . . . . . . . . . . . . . . 12

Step 6: Gas Requirements and Hookup . . . . . . . . . . . . . . . . . 14

Step 7: Electrical Requirements, Connection & Grounding . . . 16

Step 8: Backguard Installation (optional) . . . . . . . . . . . . . . . . . 19

Step 9: Placing and Leveling the Range . . . . . . . . . . . . . . . . . 25

Step 10: Burner Test and Adjustment . . . . . . . . . . . . . . . . . . . 29

Installer Final Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

To Clean and Protect Exterior Surfaces . . . . . . . . . . . . . . . 30

This THERMADOR

®

appliance is made by

BSH Home Appliances Corporation

5551 McFadden Ave.

Huntington Beach, CA 92649

Questions?

1-800-735-4328

www.thermador.com

We look forward to hearing from you!

English Table of Contents

English 1

Safety Instructions

Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

APPROVED FOR ALL RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

IMPORTANT: Save these Instructions for the Local Gas

Inspector’s use.

INSTALLER: Please leave these Installation Instructions

with this unit for the owner.

OWNER: Please retain these instructions for future

reference.

WARNING:

Disconnect power before installing. Before

turning power ON, be sure that all controls are in

the OFF position.

Important:

Local codes vary. Installer is responsible for ensuring that

the installation, gas connections, and grounding comply

with all applicable codes. Failure to follow codal procedures

may void the warranty.

Note:

This Range is NOT designed for installation in

manufactured (mobile) homes or Recreational Park

Trailers.

DO NOT install this range outdoors.

WARNING:

Tip Over Hazard!

A child or adult can tip the range

over and be killed.Verify that the

anti-tip bracket is securely installed. Ensure the

anti-tip bracket is engaged when the range is

moved.

Do not operate the range without the anti-tip

bracket in place. Failure to follow the instructions in

this manual can result in death or serious burns to

children and adults.

Check for proper installation and use of anti-tip

bracket. Carefully tip range forward pulling from

the back to ensure that the anti-tip bracket

engages the cast aluminum base and prevents tip-

over. Range should not move more than 1 inch

(2.5cm).

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the fire department.

— Installation and service must be performed by a

qualified installer, service agency or the gas

supplier.

For Massachusetts Installations:

1. Installation must be performed by a qualified or

licensed contractor, plumber or gas fitter qualified or

licensed by the state, province or region where this

appliance is being installed.

2. Shut-off valve must be a “T” handle gas cock.

3. Flexible gas connector must not be longer than 36”

(914mm).

WARNING:

If the information in this manual is not

followed exactly, a fire or explosion may

result causing property damage,

personal injury or death.

English 2

Important Installation Information

GAS Type Verification

Verify that the appliance is correct for the type of gas

provided at installation location. Ensure that the appliance is

connected to the type of gas for which it is certified. Before

proceeding with the installation refer to “Step 6: Gas

Requirements and Hookup” on page 14

All models are certified for use with natural gas. Field

conversion of the appliance for use with propane gas supply

will require installation of conversion kit supplied with the

range (service number 553182). Only a qualified service

technician or installer should make this conversion. See LP

Conversion Kit instructions for full installation information.

WARNING:

To avoid possible burn or fire hazard, a

backguard designed specifically for this range

must be installed whenever the range is used.

Refer to “Backguard Kit Model Numbers” on page 24, for

the correct backguard models that are designed for this

range. After selecting the correct backguard, the range

must be installed properly, using the minimum clearances

to combustible surfaces specified in “Step 2: Cabinet

Preparation” on page 4.

Important:

For island installations and other installations with more

than 12” (305mm) minimum horizontal clearance between

combustible materials and the back edge of the range, a

Flush Island Trim has been supplied with the range (refer

to “Figure 2: Side View Of Clearances” on page 6). A

THERMADOR

®

Low Back or High Shelf must be

purchased separately and utilized when there is less than a

12” (305mm) horizontal clearance.

Gas Supply:

Natural Gas – 6” water column (14.9 mb) min., 14” (34.9

mb) maximum

Propane Gas – 11” water column (27.4 mb) min., 14” (34.9

mb) maximum

Electric Power Supply:

See “Step 7: Electrical Requirements, Connection &

Grounding” on page 16 for specifications.

This appliance has been tested in accordance with ANSI

Z21.1, Standard for Household Cooking Appliances (USA)

and in accordance with CAN 1.1-M81 Domestic Gas

Ranges (Canadian).

Check local building codes for the proper method of

appliance installation. Installation, electrical connections

and grounding must comply with all applicable codes. Local

codes vary and it is the responsibility of the installer to

ensure installation is in accordance with these codes. In the

absence of local codes the appliance should be installed in

accordance with the National Fuel Gas Code ANSI Z223.1/

NFPA 54 current issue and National Electrical Code ANSI/

NFPA 70-current issue. In Canada, installation must be in

accordance with the CAN 1-B149.1 and.2 – Installation

Codes for Gas Burning Appliances and/or local codes.

This appliance complies with one or more of the following

standards:

• UL 858, Standard for the Safety of Household Electric

Ranges

• UL 923, Standard for the Safety of Microwave Cooking

Appliances

• UL 507, Standard for the Safety of Electric Fans

• ANSI Z21.1, American National Standard for Household

Cooking Gas Appliances

• CAN/CSA-C22.2 No. 113-10 Fans and Ventilators

• CAN/CSA-C22.2 No. 61-08 Household Cooking Ranges

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

It is strongly recommended that this appliance be installed

in conjunction with a suitable overhead vent hood (see

“Step 1: Ventilation Requirements” on page 3). Due to the

high heat capability of this unit, particular attention should

be paid to the hood and duct work installation to assure it

meets local building codes.

CAUTIONS:

• To eliminate risk of burns or fire caused by

reaching over heated units, cabinet storage

above the surface units should be avoided.

• When connecting the unit to propane gas,

make certain the propane gas tank is

equipped with its own high-pressure regulator

in addition to the pressure regulator supplied

with the range. The maximum gas pressure to

this appliance must not exceed 14.0 inches

water column (34.9 mb) from the propane gas

tank to the pressure regulator.

• This unit is designed as a cooking appliance.

Based on safety considerations, never use it

for warming or heating a room.

English 3

Step 1: Ventilation

Requirements

It is strongly recommended that a suitable exhaust hood be

installed above the range. Downdraft ventilation should not

be used. The table below indicates the ventilation hood

options and blower capacity guidelines that are

recommended for use with all THERMADOR

®

ranges.

NOTICE:

Most range hoods contain combustible components which

must be considered when planning the installation.

Do not install a microwave oven/ventilator combination

above the range, as these type of units do not provide the

proper ventilation and are not suitable for use with the

range.

1. Select Hood and Blower Models:

• For wall installations, the hood width must, at a

minimum, equal the width of the range. Where space

permits, a hood larger in width than the range may be

desirable for improved ventilation performance.

• For island installations, the hood width should, at a

minimum, overhang the range by a minimum of 3"

(76mm) on each side.

2. Hood Placement:

• For best smoke elimination, the lower edge of the hood

should be installed 30" (762mm) above the range

cooking surface (see “Figure 1: Cabinet Clearances”

on page 5).

• If the hood contains any combustible materials (i.e. a

wood covering), it must be a minimum of 36" (914mm)

above the cooking surface.

3. Consider Make-Up Air:

• Due to the high volume of ventilation air, a source of

outside replacement air is recommended. This is

particularly important for tightly sealed and insulated

homes. A qualified heating and ventilating contractor

should be consulted.

Important:

Ventilation hoods and blowers are designed for use with

single wall ducting. However, some local building codes or

inspectors may require double wall ducting. Consult local

building codes and/or local agencies, before starting, to

assure that hood and duct installation will meet local

requirements.

Tools Needed

(2) 1/2” wrenches 1/8” (3.17mm) drill bit

3/16” (4.76mm) drill bit 12” Adjustable wrench

Hand or electric drill Tape measure

Phillips & flathead screwdrivers Marking instrument

Level Furniture dolly

T-20 Torx screwdriver Protective gloves

Items Not Included

Drywall/Concrete Anchors Pipe Compound/Tape

Rope/Twine 3/4” (19mm) Flex Line

Strain Relief

Range

Width

Range Top

Configuration

Cubic Feet per Minute

(min requirement)

Ventilation Options

36”

4 burners with griddle

800 (cfm) 36” or 42” Pro Wall Hood

36” Custom Insert w/ optional blower

42” or 48” Island Hood w/ optional blower

6 burners 1100 (cfm)

48” 6 burners with griddle 1200 (cfm)

48” or 54” Pro Wall Hood

48” Custom Insert w/ optional blower

Important Notes:

It is recommended that a THERMADOR PROFESSIONAL

®

wall or island hood or custom insert is used with THERMADOR

PROFESSIONAL

®

Ranges. Refer to www.thermador.com for a complete selection of Professional Ventilation options,

Blowers, and Accessories.

* For high output gas ranges (60,000 BTU or greater), the minimum of one (1) CFM of ventilation per 100 BTU is

recommended. If the range has a griddle, add 200 CFM to the estimated blower capacity. Additional blower capacity

may be required for longer duct runs.

For island applications, it is recommended to use a hood width that exceeds the width of the range by 6” (152mm),

overlapping the range by a minimum of 3” (76mm) on each end.

CFM = “cubic feet per minute” (standard blower capacity rating).

English 4

Step 2: Cabinet Preparation

• The range is a free standing unit. If the unit is to be

placed adjacent to cabinets, the clearances shown in

“Figure 1: Cabinet Clearances” on page 5 are required.

The same clearances apply to island installations,

except for the overhead cabinets, which must have a

space wide enough to accept the flared island hood, as

also indicated in Figure on page 5.

• The gas and electrical supply should be within the

zones shown in Figure 3 on page 7.

• Any openings in the wall behind the range and in the

floor under the range must be sealed.

• When there is less than a 12" (305mm) horizontal

clearance between combustible material and the

back edge of the range above the cooking surface, a

THERMADOR

®

Low Back or High Shelf must be

installed (see Figure 2, page 6). When clearance to

combustible material is over 12" (305mm), the

supplied THERMADOR

®

Flush Island Trim may be

used. Figure 2 indicates the space required for each

type of backguard.

• A 5” (127mm) minimum clearance is needed when the

range is installed beside a combustible side wall.

• Always keep appliance area clear from combustible

materials, gasoline and other flammable vapors and

liquids.

• Do not obstruct the flow of combustion and ventilation

air to the unit.

As defined in the “National Fuel Gas Code” (ANSI

Z223.1, Current Edition).

CAUTION:

Do not install the range such that the oven door

is flush with the cabinet face. A flush installation

could result in damage to the cabinets due to

exposure to high heat.

Note:

The maximum depth of overhead cabinets installed on

either side of the hood is 13" (330mm).

There is a 36” (914mm) minimum clearance required

between the top of the cooking surface and the bottom of

an unprotected cabinet. A 30” (762mm) clearance can be

used when the bottom of the wood or metal cabinet is

protected by not less than 1/4” (6mm) of a flame retardant

material covered with not less than No. 28 MSG sheet

steel, 0.015” (0.38 mm) thick stainless steel, 0.024” (0.61

mm) aluminum, or 0.02” (0.51 mm) thick copper.

Flame retardant materials bear the mark:

UNDERWRITERS LABORATORIES INC. CLASSIFIED

MINERAL AND FIBER BOARDS SURFACE BURNING

CHARACTERISTICS

followed by the flame spread and smoke ratings. These

designations are shown as “FHC (FIame Spread/Smoke

Developed).” Materials with “O” flame spread ratings are

flame retardant. Local codes may allow other flame spread

ratings. It is the responsibility of the installer to ensure

installation is in accordance with these ratings.



English 5

FIGURE 1: CABINET CLEARANCES

For 48” Ranges {48” (1219mm) 54” (1372mm), or 60” (1524mm) Wide Hood

{54” (1372mm) for Island

For 36” Ranges {36” (914mm) or 42” (1067mm) Wide Hood

{42” (1067mm) or 48” (1219mm) for Island

48” Range - 48” (1219mm)

36” Range - 36” (914mm)

of combustible material

Min. distance between overhead cabinets

30” (762mm) min. from bottom

of Overhead Hood to cooking

surface. 36” (914mm) min. If

hood contains combustible

materials.

minimum

18” (457mm)

36” (914mm) or 48” (1219mm)

13” (330mm)

Max Cabinet

Depth

Range width

5” (127mm)

min. to

combustible

material

(both sides).

CAUTION!

See Figure 2

36” (914mm) Min.

material

from cooking

Surface

to combustible

For Electrical & Gas Supply zones,

see Figure 3. Zone sizes & positions differ

according to model.

as defined in the “National Fuel Gas Code” ANSI Z223.1,

Current Edition). *The range height is adjustable. The level

of the range top must be at the same level or above the

countertop level.

*35

7

/

8

” (911mm) Min. range height

*36

3

/

4

” (933mm) Max range height

with leveling legs fully extended.

with leveling legs fully retracted.

Gas

Zone

Electrical

Zone

sidewall

English 6

Combustible Materials

48

3

/

4

” (1238mm)

28

1

/

2

” (723

mm)

29

” (737mm)

31

3

/

8

” (797mm)

25

1

/

8

” (638mm)

High Shelf

12” (306mm)

to combustible

materials

36” (914mm) Min

.

22” (559mm)

3” (76mm)

36

3

/

4

” Max (933mm)

35

7

/

8

” Min (911mm)

Installation with Low Back or High Shelf

materials

36” (914mm) min

to combustible

Installation with Included Flush Island Trim

Cantilever

12” (305mm) Min

to Combustible

with Flush Island

Trim

36

3

/

4

” Max (933mm)

35

7

/

8

” Min (911mm)

Combustible Materials

Flush Island Trim

Note: For Flush Island

Trim installations,

counter surface should

have a cantilever edge

meeting the back section

of the Flush Island Trim

accessory.

Note: If an inner wall is

used under the cantilever

counter top, there should

be a 1/8” (3mm) gap from

the rear of the range to the

inner wall.

As defined in the

“National Fuel Gas

Code” (ANSI Z223.1,

Current Edition).



Low Back

Guard

12”

(305mm)

minimum

recess depth

FIGURE 2: SIDE VIEW OF CLEARANCES

English 7

Gas and Electric Supply Zone

Notice:

• If not already present, install gas shut-off valve in an

easily accessible location.

• Make sure all users know where and how to shut off

the gas supply to the range.

• Any opening in the wall behind the appliance and any

opening in the floor under the appliance must be

sealed.

The dual fuel ranges may be connected to the power

supply with a range supply cord kit or by hard-wiring to the

power supply. It is the responsibility of the installer to

provide the proper wiring components (cord or conduit and

wires) and complete the electrical connection as dictated

by local codes and ordinances, and/or the National Electric

Code. The units must be properly grounded. Refer to

“Step 7: Electrical Requirements, Connection & Grounding”

on page 16 for details.

The range must be connected only to the type of gas for

which it is certified. If the range is to be connected to

propane gas, ensure that the propane gas supply tank is

equipped with its own high pressure regulator in addition to

the pressure regulator supplied with the range (see

“Step 6: Gas Requirements and Hookup” on page 14).

Note:

The range is designed for nearly-flush installation to the

back wall. For a successful installation, it may be

necessary to reposition the gas supply line and electrical

cord as the range is pushed back to its final position. It is

suggested that this may be accomplished by carefully

pulling on a rope or twine looped around the gas or

electrical supply line which is pulled from beneath the

range and out the front as the range is pushed back into its

final position.

Figure 3: Gas & Electrical Supply Locations

A

B

CD

10” (254mm)

2” (51mm)

36” (913mm)

3” (76mm)

48” (1219mm)

Model A B C D

36” (913mm)

9

1

/

8

” (232mm) 7

3

/

8

” (187mm) 7

3

/

8

” (187mm) 9

1

/

8

” (232mm)

48” (1219mm)

23

1

/

8

” (587mm)

7” (178mm) 7” (587mm)

7

/

8

” (200mm)

English 8

Electrical Supply

Installation of the range must be planned so that the rough-

in of the terminal block for the receptacle or conduit

connection will allow maximum clearance to the rear of the

unit.

When the power supply cord or conduit is connected to the

mating receptacle or terminal block cover, the combined

connection should protrude no more than 2“(51mm) from

the rear wall (see Figure 4).

Refer to Figure 11 on page 16 for location of the terminal

block on unit. To minimize binding when the unit is

connected, orient the receptacle or conduit connector, and

slide back into position.

Step 3: Unpacking and Moving

the Range

CAUTION:

The unit is heavy and should be handled

accordingly. Proper safety equipment such as

gloves and adequate manpower of at least two

people must be used in moving the range to

avoid injury and to avoid damage to the unit or

the floor. Rings, watches, and any other loose

items that may damage the unit or otherwise

might become entangled with the unit should be

removed.

Hidden surfaces may have sharp edges. Use

caution when reaching behind or under

appliance.

The range has an approximate shipping weight as shown in

“Chart A”. The grates, griddle plate, burner caps, and oven

racks must be removed to facilitate handling. Do not

remove the griddle element and tray assembly.

1. Remove the outer carton and packing materials from

the shipping pallet but leave the adhesive-backed foam

layer over brushed-metal surfaces, to protect finish

from scratches, until the range is installed in its final

position.

2. Remove the door(s) (see “Step 4: Door Removal and

Reinstallation” on page 10); however, do not remove

the warming drawer or steam oven doors. This will

create an estimated reduction in the weight as shown

in “Chart A” and allow the range to pass through 30"

(762mm) doorways (see clearances shown on page 6).

Caution

DO NOT lift the range by the oven door's handle,

as this may damage the door hinges and cause

the door to fit incorrectly.

Figure 4: Wall Connection

2” (51mm) maximum

when plugged in

2” (51mm)

maximum

Chart A

36"

Range

48"

Range

Shipping Weight 420 lbs

(191 kg)

590 lbs

(268 kg)

Weight without packing

materials

360 lbs

(163 kg)

530 lbs

(240 kg)

Without door(s), burner caps,

and oven racks

260 lbs

(118 kg)

390 lbs

(177 kg)

English 9

Remove all tape and packaging before using the

appliance. Please, recycle the packaging

material, as all THERMADOR

®

appliance

packaging material is recyclable. Never allow

children to play with packaging material.

3. All ranges are held to the pallet by (4) bolts through a

wood block center (see Figure 5). The two front pallet

bolts are accessible only after removing the Door

Trim located beneath the doors.

• The Door Trim is removed by loosening the 2

screws attaching it to the range and sliding it up

and off the screws.

4. After removing the pallet bolts using (2) 1/2” (13mm)

wrenches (one to hold bolt at the bottom while the

other is loosening the nut at the top) and discarding the

wood packing block inserts, the range may be carefully

tilted back on the (2) casters (see Figure 24 on

page 25) and removed from the pallet. Use additional

help as required to remove from pallet.

• Due to the weight, a furniture dolly with soft wheels or

an air lift should be used to move this unit. The weight

must be supported uniformly across the bottom (see

Figure 6).

• After transporting the range by dolly close to its final

location, the range can be tipped back and supported on

the rear casters while the dolly is carefully removed.

• “Step 5: Installing Anti-Tip Device”, “Step 6: Gas

Requirements and Hookup”, “Step 7: Electrical

Requirements, Connection & Grounding”, and

“Step 8: Backguard Installation (optional)” must be

completed before the range is placed in its final

position.

• Use the casters to assist with the installation near to its

final location. THE FLOOR UNDER THE LEGS

SHOULD BE PROTECTED BEFORE PUSHING THE

UNIT INTO POSITION.

Figure 5: Door Trim, Packing Blocks, & Pallet Bolts

Wood Packing Blocks

Pallet Bolts

Loosen Screws

Figure 6: Furniture Dolly Positioning

braces

22

3

/

4

” (578mm)

bottom of

Range must

be uniformly

supported by

provided on

range.

English 10

Step 4: Door Removal and Reinstallation

CAUTION:

USE CAUTION WHEN REMOVING THE DOOR.

THE DOOR IS VERY HEAVY.

• Make sure oven is cool and power to the oven has

been turned off before removing the door. Failure

to do so could result in electrical shock or burns.

• The oven door is heavy and fragile. Use both

hands to remove or replace the door.

• Failure to grasp the oven door firmly and properly

could result in personal injury and product damage.

• With the door off, never release the levers and try

to close the hinges. Without the weight of the door,

the powerful springs will snap the hinges closed

with great force.

To Remove the Oven Door:

1. Open the door fully and use a screwdriver to carefully

pry the hinge clips away from the hinge slots (Photo A).

2. Flip the hinge clip toward you (Photo B).

3. Close the door until it stops against the hinge clips. The

open hinge clips will hold the door open at a slight

angle.

4. Grasp the door firmly on the ends of the door handle,

and lift the door up. (There will be some spring

resistance to overcome.) When the door is lifted

sufficient to clear the hinge hooks, the door can be

pulled straight out (Photo C). Place the door in a safe

and stable location.

Photo A

Photo B

Photo C

English 11

To Reinstall the Oven Door:

1. Position the door at a sharp angle (see Figure 7) and

insert the hinges centered evenly into the hinge slots.

The hinges will securely hook into the slots when

properly installed. Do not force, bend, or twist the door.

• Tip: Rest the door on your foot while using your leg

for stability.

2. Open the door fully and use a screwdriver to push the

hinge clips all the way into the hinge slots (toward the

oven) until they meet the hinge. Be careful not to

scratch the range during this process.

To Check Door Fit and Operation:

1. Open and close the door slowly to test the movement

and the fit of the door to the oven cavity. Do not force

the door to open or close. If the door is properly

installed, it should move smoothly and rest straight on

the front of the range when closed.

2. If the door does not operate correctly, verify that the

hinges are properly seated into the hinge slots, and

that the hinge clips are fully engaged into the slots.

3. For large and small ovens, if door or handle appears

slightly tilted, you may adjust the hinge receiver by

rotating the large Torx-head screw located directly

above the hinge receiver with a T-20 Torx driver.

Rotate each screw respective to its side and direction

the door needs to be adjusted (Photo D).

• The warming drawer and steam oven doors are not

adjustable.

Figure 7: Approximate Door Angle for Removal

23°

Turn this

screw to

adjust door

alignment

Photo D

English 12

Step 5: Installing Anti-Tip Device

WARNING — RANGE TIPPING

HAZARD:

• To prevent accidental tipping of the range, attach it to

the floor by installing the Anti-Tip Device supplied.

• A risk of tip-over may exist and injury can result if the

appliance is not installed in accordance with these

instructions. For all ranges an anti-tip device must be

installed as per these instructions.

• If the range is pulled away from the wall for cleaning,

service or for any other reason, ensure that the Anti-

Tip Device is properly re-engaged when the range is

pushed back against the wall. In the event of abnormal

usage (such as a person standing, sitting, or leaning

on an open door), failure to take this precaution can

result in tipping of the range. Personal injury might

result from spilled hot liquids or from the range itself.

WARNING — ELECRICAL SHOCK

HAZARD:

• Use extreme caution when drilling holes into

the wall or floor as there may be concealed

electrical wires.

• Identify the electrical circuits that could be

affected by the installation of the Anti-Tip Device,

then turn off power to these circuits.

• Failure to follow these instructions may result

in electrical shock or other personal injury.

ATTENTION — PROPERTY DAMAGE:

• Contact a qualified installer or contractor to determine the

proper method for drilling holes through the wall or floor

material (such as ceramic tile, hardwood, etc.)

• Do not slide the range across an unprotected floor.

• Failure to follow these instructions may result in damage

to wall or floor coverings.

Tools Needed for Installation of Anti-Tip

Device:

• Screwdriver, Phillips

• Drill, electric or hand

• Measuring tape or ruler

• 1/8” (3.17mm) drill bit (wood or metal; wall or floor)

• 3/16” (4.76mm) carbide-tipped masonry drill bit (concrete

or concrete block wall or floor)

• 3/16” (4.76mm) anchors, drywall or concrete, 4 each (not

required if mounting bracket is being attached to solid

wood or metal)

• Hammer

• Pencil or other marker

WARNING

--A child or adult can tip the range and

be killed.

--Verify the anti-tip device has been

properly installed and engaged as per

installation instructions.

--Ensure the anti-tip device is re-

engaged when the range is moved.

--Do not operate the range without the

anti-tip device in place and engaged.

--Failure to do so can result in death or

serious burns to children or adults.

--See further Installation Instructions.

THERMADOR

Service Part No.

Qty Description

415078 4

Screw, Phillips, #10 x 1

1

/

2

”

(38.1mm)

655355 1 Anti-Tip Bracket

English 13

Important Installation Information:

• Attach anti-tip bracket to a solid wood cabinet having a

minimum wall thickness of 3/4” (19mm). The thickness

of the wall or floor may require use of longer screws,

available at your local hardware store.

• Use appropriate anchors when fastening the mounting

bracket to any material other than hard-wood or metal.

• In all cases, at least (2) of the bracket mounting screws

must firmly fasten the anti-tip bracket to the floor, and

(2) of the mounting screws (or drywall anchors) must

firmly fasten the anti-tip bracket to the rear wall (see

Figure 8 and Figure 9).

Mounting the Anti-Tip Bracket

1. Prepare holes at fastener locations as identified below:

• For walls, wall studs, or floors composed of solid

wood or metal, drill 1/8” (3.17mm) pilot holes.

• For walls or floors composed of drywall, sheet-rock

or other soft materials, drill 3/16” (4.76mm) holes to a

minimum depth of 1

3

/

4

” (44mm), then tap plastic

anchors into each of the holes using a hammer.

• For walls or floors composed of concrete or concrete

block, drill 3/16” (4.76mm) holes to a minimum depth

of 1

3

/

4

” (44mm), then tap concrete anchors into each

of the holes using a hammer.

• For walls or floors having ceramic tile covering, drill

3/16” (4.76mm) holes through the tile only, then drill

into the material behind the tile as indicated

immediately above.

• Place bracket on floor near the center of where the

unit is to be finally located (shown in Figure 8).

• If the range is moved to a new location, the Anti-Tip

Device must be reinstalled.

2. Secure bracket into the wall stud and to the floor using

the screws provided.

3. Later, when the unit is installed, the adjustable legs will

allow the cast base to slide under the bracket hook,

stabilizing the unit.

Figure 8: Anti-tip Bracket Mounting Location

3”

(76mm)

Figure 9: Anti-tip Bracket

English 14

Step 6: Gas Requirements and Hookup

Verify the type of gas being used at the installation site.

Make certain the range matches the type of gas available

at this location. The appliance is shipped from the factory

for use with natural gas. It must be converted for use with

propane.

Field conversion of the appliance for use with propane gas

supply will require installation of the conversion kit supplied

with the range (service number 553182). A qualified

technician or installer must do the conversion. See LP

Conversion Kit instructions for full installation information.

Obey all instructions in this kit for correct conversion of the

gas regulator and settings for the gas valves.

CAUTION:

When connecting unit to propane gas, make

certain the propane gas tank is equipped with its

own high pressure regulator in addition to the

pressure regulator supplied with the appliance.

The pressure of the gas supplied to the

appliance regulator must not exceed 14" water

column (34.9 mb).

WARNING:

Do not remove the back cover of the range. It is

for an authorized servicer access only.

WARNING:

If a gas conversion kit is used, the kit shall be

installed by a qualified service agency in

accordance with the manufacturer’s instructions

and all applicable codes and requirements of the

authority having jurisdiction. If the information in

the instructions is not followed exactly, a fire,

explosion, or production of carbon monoxide

may result causing property damage, personal

injury, or loss of life. The qualified service agency

is responsible for the proper installation of the kit.

The installation is not proper and complete until

the operation of the converted appliance is

checked as specified in the manufacturer’s

instructions supplied with the kit.

Hook Up

The gas supply connections shall be made by a competent

technician and in accordance with local codes or

ordinances. In the absence of local codes, the installation

must conform to the National Fuel Gas Code ANSI Z223.1/

NFPA54- current issue.

NATURAL GAS REQUIREMENTS:

Inlet Connection: 3/4” (19mm) NPT external

1/2” (12.7mm) NPT internal

(Minimum 3/4” dia. flex line.)

Supply Pressure: 6" min. to 14" max. water

column.

(14.9 to 34.9 mb)

Manifold Pressure: 5" water column (12.5 mb)

PROPANE GAS REQUIREMENTS:

Inlet Connection: 3/4” (19mm) NPT external

1/2” (12.7mm) NPT internal

(Minimum 3/4” dia. flex line.)

Supply Pressure: 11" min. to 14" max. water

column. (27.4 mb to 34.9 mb)

Manifold Pressure: 10" water column (24.9 mb)

Figure 10: Manifold Gas Line Connection

Gas Line Connection

English 15

A manual gas shut-off valve must be installed external to

the appliance, in a location accessible from the front, for

the purpose of shutting off the gas supply. The supply line

must not interfere with the back of the unit.

The range is supplied with its own pressure regulator that

has been permanently mounted inside the range.

• Make sure the gas supply is turned off at the manual

shut-off valve before connecting the appliance.

• Use 3/4” (19mm) flex line to connect between the gas

supply and the appliance inlet pipe, which exits the

rear, lower right of the appliance. The appliance pipe

connection has a 3/4” (19mm) NPT external thread and

a 1/2” (13mm) NPT internal thread (see Figure 10 on

page 14).

• Use caution to avoid crimping the 3/4” (19mm) flex

line when making bends.

• Suggested length of the flex line is 48” (1219mm);

however, check local codes for requirements

before installation.

• Use pipe sealing compound or Teflon

®

tape on the

pipe threads, and be careful not to apply excessive

force when tightening the fittings.

Leak testing of the appliance shall be in accordance with

the following instructions.

• Turn on gas and check supply line connections for

leaks using a soap and water solution.

• Bubbles forming indicate a gas leak. Repair all

leaks immediately after finding them.

WARNING:

Do not use a flame of any kind to check for gas

leaks.

Installer is responsible for ensuring that the installation, gas

connections, and grounding comply with all applicable

codes.

CAUTION:

The appliance must be isolated from the gas

supply piping system by closing its individual

manual shut-off valve during any pressure

testing of the gas supply piping system at test

pressures equal to or less than 1/2 psig

(3.5kPa.).

The appliance and its individual shut off valve must be

disconnected from the gas supply piping system during any

pressure testing of the system at test pressures in excess

of 1/2 psig (3.5kPa.).

When checking the manifold gas pressure, the inlet

pressure to the regulator should be at least 6.0" W.C. (14.9

mb) for natural gas or 11.0" W.C. (27.4 mb) for propane.

Do not attempt any adjustment of the pressure regulator.

English 16

Step 7: Electrical Requirements, Connection & Grounding

• Prior to servicing appliance, always disconnect appliance electrical supply cord, if so equipped, from wall receptacle. If

appliance is hard-wired to power supply, disconnect power to unit by turning off the proper circuit breaker or

disconnecting the proper fuse. Lock service panel to prevent power from being turned ON accidentally.

Dual Fuel range models can be connected or hardwired to the power supply as described on page 17.

• A neutral supply wire must be provided from the power

source (breaker/fuse panel) because critical range

components, including the surface burner spark re-

ignition module, require 120 VAC to operate safely and

properly.

WARNING:

An improper 120/ 240 VAC power supply will

cause malfunction, damage to this appliance,

and possibly create a condition of shock hazard.

• If the correct power supply circuit is not provided, it is

the responsibility and obligation of the installer and

user to have proper power supply connected. This

must be accomplished in accordance with all

applicable local codes and ordinances by a qualified

electrician. It is the responsibility of the installer to

ensure compliance of local codes. In the absence of

local codes and ordinances, the power supply

connection shall be in accordance with the National

Electric Code.

• Observe all governing codes and ordinances when

grounding. In the absence of these codes or

ordinances observe National Electrical Code ANSI/

NFPA No. 70 current issue. See the following

information in this section (Step 7) for grounding

method.

• Electrical wiring diagrams and schematics are attached

behind the Door Trim of the range, for access by a

qualified service technician (see Figure 5 page 9).

• The ranges are to be connected to a 240/208 VAC

power supply.

Dual Fuel models must be connected to the power supply

utilizing one of the following methods. For all methods of

connection, the length of the cord or conduit/wiring must

allow the unit to be slid completely out of the cabinet

without having to unplug or disconnect the unit from the

power supply. Recommended minimum free length of cord

or conduit is 4ft (1.2m). Electrical installations and

grounding must be in accordance with all local codes and

ordinances, and/or the National Electric Code, as

applicable.

Chart B: Electrical Supply Circuit Requirements

MODEL

TYPE

VOLTAGE

CIRCUIT

RATING

FREQUENCY PHASE

36” 240/208 VAC 40 Amps 60 Hz. Single

48" 240/208 VAC 50 Amps 60 Hz. Single

Figure 11: Terminal Block Location

Terminal Block

Location

Range: Left Side

English 17

PERMANENT CONNECTION (HARD WIRING) —

Units may be hard wired to the power supply. The installer

must provide approved flexible aluminum conduit, 3/4”

(19mm) trade size, maximum 6ft (1.8m) long. Locate the

terminal block on the rear of the unit and remove cover

(refer to Figure 11). The conduit must be installed to the

terminal block using an approved conduit connector. The

free end of the conduit must be connected to a junction box

provided in the electrical supply zone, as shown in Figure 3

on page 7.

Mount a strain relief (not provided) into the 1" (25.4mm)

diameter hole located below the terminal block (see

Figure 13). Wiring for the unit is to be brought into the

terminal block through the conduit and through the strain

relief. The ends of the wiring must have 1/4” faston closed-

loop lugs attached, preferably soldered in place. Make the

connections to the terminal block provided (see Figure 12).

If aluminum supply wiring exists in the installation, splice

the aluminum house wiring with appropriate-thickness

gauge copper wire for adapting to the range, using special

connectors designed and certified for joining copper and

aluminum wire. Follow the connector manufacturer’s

recommended installation procedure.

WARNING:

Improper connection of aluminum house wiring

can result in a fire or shock hazard. Use only

connectors designed and certified for connecting

to aluminum wire.

Installer — show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

4-CONDUCTOR CORD— NORMALLY, A UNIT MUST BE

CONNECTED TO THE POWER SUPPLY WITH A 3-

POLE, 4-CONDUCTOR CORD KIT RATED 125/250

VOLTS, 50 AMPERES, AND MARKED FOR USE WITH

RANGES.

The cord kit must be attached to the range terminal block

with a strain relief which will fit a 1" (25.4mm) diameter

hole. If not already equipped, the cord must also have 1/4”

(6mm) faston closed-loop lugs attached to the free ends of

the individual conductors, preferably soldered in place.

4-Wire Connection

1. Remove upper nuts only from the terminal block studs.

Do not remove lower nuts which secure range internal

wiring leads.

2. Mount strain relief (not provided with range) into the 1"

(25.4mm) diameter hole in the back panel located

below the terminal block (see Figure 13 and

Figure 12). Route wires up through strain relief.

3. Secure the neutral, grounded wire of the supply circuit,

to the center stud of the terminal block with nut (see

Figure 14).

4. Secure the L1 (black) and L2 (red) power leads to the

outside terminal studs (brass colored) with nuts.

5. Remove green ground screw located beneath the

terminal block. Discard white wire.

6. Secure the bare copper ground lead to the range

chassis using the ground screw previously used for the

white wire. Be sure that neutral and ground terminals

do not touch.

Figure 12: Terminal Block

Figure 13: Strain Relief Location

Terminal Block

Strain

Relief

English 18

7. Tighten all connections securely.

8. Reinstall the Terminal Block Cover.

3-CONDUCTOR CORD — WHERE LOCAL CODES AND

ORDINANCES PERMIT GROUNDING THROUGH

NEUTRAL, AND CONVERSION OF SUPPLY TO 4 WIRE

IS IMPRACTICAL, UNIT MAY BE CONNECTED TO THE

POWER SUPPLY WITH A 3-POLE, 3-CONDUCTOR

CORD KIT RATED 125/250 VOLTS, 50 AMPERES, AND

MARKED FOR USE WITH RANGES.

The cord kit must be attached to the range back panel with

a strain relief which will fit a 1" (25.4mm) diameter hole. If

not already equipped, the cord must also have 1/4” (6mm)

faston closed-loop lugs attached to the free ends of the

individual conductors, preferably soldered in place.

3-Wire Lead Connection

1. Remove upper nuts only from the terminal block studs.

Do not remove nuts which secure range internal wiring

leads.

2. Mount strain relief (not provided with range) into the 1"

(25.4mm) diameter hole in the back panel located

below the terminal block (see Figure 13 and

Figure 12). Route wires up through strain relief.

3. Secure the neutral, grounded wire of the supply circuit,

to the center stud (silver colored) of the terminal block

(see Figure 15).

4. Secure the L1 (black) and L2 (red) power leads to the

outside corresponding terminal block studs (brass

colored).

5. Secure one end of the mounted looped neutral wire,

located beneath terminal block, to the center stud of

the terminal block with nut and keep the other end of

the wire screwed into the back of the range.

6. Tighten nuts securely.

7. Reinstall the Terminal Block Cover.

Figure 14: 4-Wire Connection

Figure 15: 3-Wire Connection

La page charge ...

Thermador PRD366JGU Guide d'installation

Ce manuel convient également à

Thermador PRD366JGU Guide d'installation

dans d''autres langues

Documents connexes

Autres documents