Faber Inca Pro 30 X 19 SS NB-B Guide d'installation

Marque: Faber

Modèle: Inca Pro 30 X 19 SS NB-B

Catégorie: Hottes

Taper: Guide d'installation

INPL3019SSNB-B

INPL3619SSNB-B

INPL3622SSNB-B

INPL4219SSNB-B

INPL4819SSNB-B

INPL4822SSNB-B

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

INCA PRO PLUS

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START

INSTALLING THIS RANGEHOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on low or medium setting.

b) Always turn hood ON when cooking at high heat or when ambeing food (i.e. Crepes Suzette,

Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or lter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP

GREASE FIRE, OBSERVE THE FOLLOWING*:

a) SMOTHER FLAMES with a close-tting lid, cookie sheet, or metal tray, then turn o the burner. BE

CAREFUL TO PREVENT BURNS. If the ames do not go out immediately EVACUATE AND CALL THE

FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. The re is small and contained in the area where it started.

3. The re department is being called.

4. You can ght the re with your back to an exit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan with any

solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer. If you have any questions,

contact the manufacturer.

b) Before servicing or cleaning unit, switch power o at service panel and lock the service discon-

necting means to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explosive

Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OB-

SERVE THE FOLLOWING:

1. Installation Work And Electrical Wiring Must Be Done By Qualied Person(s) In Accordance

With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sucient air is needed for proper combustion and exhausting of gases through the ue

(chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment

manufacturer's guideline and safety standards such as those published by the National

Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE), and the local code authorities.

ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED

MUST BE SEALED.

This rangehood requires at least 24" of clearance between the bottom of the rangehood and the cooking

surface or countertop. This hood has been approved by UL at this distance from the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops and combination

ranges, a minimum of 30" is recommended and may be required.

Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking surface or

countertop. Consult the cooktop or range installation instructions given by the manufacturer before

making any cutouts.

MOBILE HOME INSTALLATION The installation of this rangehood must conform to the Manufactured Home

Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280). See Electrical Requirements.

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the wall

or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide ecient

performance. The size of the ductwork should be uniform. Do not install two elbows together. Use duct tape

to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor opening around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence that

greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts. Do not

cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must

be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION - To reduce risk of re and to properly exhaust air, be sure to duct air outside – Do not vent

exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other

hidden utilities.

4. Ducted fans must always be vented to the outdoors.

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A time-delay

fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with the

electrical rating of this unit as specied on the serial/rating plate located inside the unit near the eld wiring

compartment.

ELECTRICAL INSTALLATION WITH WIRING BOX

THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes must conform to the requirements

of the National Electrical Code, ANSI/NFPA 70 - latest edition, and all local codes and ordinances. Wire size

and connections must conform with the rating of the appliance. Copies of the standard listed above may

be obtained from:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

This appliance should be connected directly to the fused disconnect (or circuit breaker) through

exible, armored or nonmetallic sheathed copper cable. Allow some slack in the cable so the ap-

pliance can be moved if servicing is ever necessary. A UL Listed, 1/2" conduit connector must be

provided at each end of the power supply cable (at the appliance and at the junction box).

When making the electrical connection, cut a 1 1/4" hole in the wall. A hole cut through wood must

be sanded until smooth. A hole through metal must have a grommet.

• Electrical ground is required on this rangehood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO NOT

use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding

circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the rangehood is

properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

State of California Proposition 65 Warning (US only)

WARNING

This product contains chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

RANGEHOOD DIMENSIONS

12-5/16"

10-13/16"

18-11/16"

21-1/4" (A1) - 22-1/2" (A2)

28-9/16" (A3) - 34-9/16" (A4)

7-15/16"

1/2"

3-1/8"

11"

28-1/2" (A1) - 34-1/2" (A2)

40-9/16" (A3) - 46-9/16" (A4)

29-1/2" (A1) - 35-1/2" (A2)

41-9/16" (A3) - 47-9/16" (A4)

1/2"

20-11/16"

19-11/16"

15-5/16"

10-13/16"

18-11/16"

22-1/2" (A1) - 34-9/16" (A2)

7-15/16"

1/2"

3-1/8"

11"

34-1/2" (A1) - 46-9/16" (A2)

35-1/2" (A1) - 47-9/16" (A2)

1/2"

23-11/16"

22-11/16"

Index Model #

A1 INPL3019SSNB-B

A2 INPL3619SSNB-B

A3 INPL4219SSNB-B

A4 INPL4819SSNB-B

Index Model #

A1 INPL3622SSNB-B

A2 INPL4822SSNB-B

MAIN PARTS

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with:

Controls, Light, Filters, Blower.

4 2 Front / back trim

5 2 Left/right trim

6 2  Greaselters(30")

6 3  Greaselters(36"-42")

6 4  Greaselters(48")

7 4  Filterknobs(30")

7 6  Filterknobs(36"-42")

7 8  Filterknobs(48")

8 1  Greaserail

10 10  Stopper

Ref. Qty. Installation Components

9c 14  Installscrews(1/8"x1/4")

9d 6  Installscrews(1/8"x5/16")

9e 4  Greaseltersscrews(3/16"x5/16"-30")

9e 6  Greaseltersscrews(5/32"x5/16"-36"-42")

9e 8  Greaseltersscrews(5/32"x5/16"-48")

Qty. Documentation

1 Instruction Manual

Activated Charcoal

Filter sku #; FILTER1

Activated Charcoal

Filter sku #; FILTER1LL

Internal 300 cfm Blower sku #; IB300

Internal 600 cfm PRO Blower sku #;

IB600

Internal 1,200 cfm PRO Blower sku #;

IB1200

Remote Blower 900 cfm

sku #; RB900

Remote Blower 1,200 cfm

sku #; RB1200

In-Line Blower Connection Kit sku #;

INLBKIT

Available

Accessories

Version 07/11 - Page 6

INSTALLATION

COMBINATIONS HOOD AND MOTOR KITS

CHOOSE A BLOWER FOR YOUR HOOD

After choosing the hood width and depth for your cooking

needs, next choose the type of blower appropriate for

your cooking.

NOTE: no other blower is

compatible with this hood, except for the

kits below.

# IB300 - Internal Blower Kit 300 cfm

# IB600 - Internal Blower Kit 600 cfm

# IB1200 - Internal Blower Kit 1200 cfm

# RB900 - Remote Blower Kit 900 cfm

# RB1200 - Remote Blower Kit 1200 cfm

# INLBKIT - In Line Blower Kit

(supply own in-line blower)

OPTIONAL ACCESSORIES AVAILABLE

• *Charcoal Filter

* it is highly recommended that professional style cooking always be

vented to the outside; for recirculating installations only, some ductwork is

required to exhaust the unit out of the cabinet. Replace as needed with the

same model

part # FILTER1

NOTE: The charcoal ﬁlter kit for use with the 300 / 600

cfm internal blower kit ONLY

CAUTION - To reduce risk of ﬁre and electric shock, install this rangehood only with: Remote blower manufacturer by Faber

models RB900 and RB1200 or Integral blower manufactured by Faber models IB300 or IB600 or IB1200 or with INLBKIT and

generic in-line blower rated max 4.2 A suitable for use with solid state variable speed control

INLBKIT

CAUTION - To reduce the risk of re and electric shock, install this rangehood only with Remote blower

manufactured by Faber models RB900 and RB1200, or Internal blower manufactured by Faber models IB300

or IB600 or IB1200 with the INLBKIT accessory kit purchased separately. When using a generic In-Line Blower

or Remote Blower it must be rated maximum 4.2 A suitable for use with solid state variable speed control and

also used with the INBKLIT accessory kit purchased separately.

For the 30" Inca it is recommended that blowers are kept at MAX. CFM of 600.

INSTALLATION

COMBINATIONS HOOD AND MOTOR KITS

1. Install the Plate B (Figure 2) which came with

the internal blower kit, on top of the rangehood

with the hole closer to the back of the hood. Use 9

screws supplied with the blower kit.

Version 07/11 - Page 8

INSTALLATION WITH IB300 / IB600 INTERNAL BLOWER (300

, 600 cfm)

1. Install the Plate B (FIGURE 8) which came with the internal

blower kit, on top of the rangehood with the hole closer to the back

of the hood. Use 9 screws supplied with the blower kit

6. (see FIGURE 13) Remove the cover from the ﬁeld wiring

compartment with a phillips screwdriver. Feed the Power Supply

Cable through the electrical knockout. Connect the Power Supply

Cable to the rangehood cable. Attach the White lead of the power

supply to the White lead of the rangehood with a twist-on type wire

connector. Attach the Black lead of the power supply to the Black

lead of the rangehood with a twist-on type wire connector. Attach

the Power Supply Cable grounding lead to the green screw provided.

Replace the cover.

7. Connect the ductwork to the damper and seal all connections with

duct tape. Install the grease ﬁlters and grease rail. (see page 11 for

instructions)

8. Turn the power supply on. Turn on the blower and light. If the

rangehood does not operate, check that the circuit breaker is not

tripped or the house fuse blown. If the unit still does not operate,

disconnect the power supply and check that the wiring connections

have been made properly.

9. CONTINUE TO PAGE 11

FIGURE 8

2. Remove the white plastic covering and install the 4 side trim

pieces to the outside of the hood using (16) part 9b screws, see

the side rail installation in (FIGURE 9).

FIGURE 9

5. Attach the hood to the cabinet using (12) 9c. screws to the

cabinet. FIGURE 12

FIGURE 12

FIGURE 10

3. Install the motor kit into the hood using the 2 screws supplied

with the motor kit into the back of the hood. (FIGURE 10)

4. Connect the wire that comes with the motor kit from the side

of the motor to the connection on the inside of the light panel in

the hood. The 9 hole end of the wire is installed in the motor, the

6 hole end is connected to the light panel (FIGURE 11)

FIGURE 11

FIGURE 13

FOR ALL INSTALLATIONS REMOVE ALL WHITE PLASTIC PROTECTIVE COVERING FROM

HOOD, SIDE RAILS, TRIM, GREASE RAILS AND GREASE FILTERS.

2. Remove the white plastic covering and install

the 4 side trim pieces (4-5) to the outside of the

hood using (14) part 9c screws, see the side trim

installation in (Figure 3).

INSTALLATION WITH IB300 / IB600 INTERNAL BLOWER

(300, 600 cfm)

FIGURE 2

FIGURE 3

RECIRCULATING INSTALLATIONS

IT IS HIGHLY RECOMMENDED THAT PROFESSIONAL STYLE COOKING ALWAYS BE VENTED

TO THE OUTSIDE. For recirculating installations (Figure 1), Charcoal Filters are necessary. Remove

all grease lters and set aside. Attach one charcoal lter to each end of the blower. Each charcoal lter

attaches to the grid on the side of the blower. Rotate the lter clockwise to install and counterclockwise

to remove (Figure 1A). Replace all grease lters. Recirculating installations also require some duct work

to divert the air out of the top or face or side of the cabinet or custom hood or out of the side / face of

the sot and back into the kitchen. Install at least 15" of vertical run of metal duct (Figure 1) at the air

outlet. Run the duct vertically and secure it at the relevant opening previously cut out at the top or side

of the cabinet or sot. A metal duct cover grille is also recommended. The duct work must not terminate

inside the cabinet or custom hood.

Version 07/11 - Page 7

PLAN YOUR DUCTWORK

To ensure that the blower performs to its highest

possible capacity, ductwork should be as short

and straight as possilbe.

The ductrun should not exceed 35 equivalent

feet if ducted using the required minimum of 6"

round duct. For 10" round ducting with the 1200

cfm internal motor or 900 / 1200 remote blower,

use 55 equivalent feet. Calculate the length of

the ductwork by adding the equivalent feet in

FIGURE 5 for each piece of duct in the system

An example is given in FIGURE 6.

For best results, use no more than three 90°

elbows. Make sure that there is a minimum of

24" of straight duct between elbows if more

than one is used. Do not install two elbows

together. If you must elbow right away, do it

as far away from the hood's exhaust opening

as possible.

9 Feet Straight Duct

2 - 90˚ Elbows

Wall Cap

Total System

9.0 feet

10.0 feet

0.0 feet

19.0 feet

FIGURE 6

3.0 feet

5.0 feet

12.0 feet

0.0 feet

45˚ Elbow

90˚ Elbow

90˚ Flat Elbow

Wall Cap

FIGURE 5

FIGURE 4

RECIRCULATING INSTALLATIONS

IT IS HIGHLY RECOMMENDED THAT PROFESSIONAL STYLE COOKING ALWAYS BE VENTED TO THE OUTSIDE. For recirculating

installations (FIGURE 4), Charcoal Filters are necessary. Remove all grease ﬁlters and set aside. Attach one charcoal ﬁlter to each end

of the blower. Each charcoal ﬁlter attaches to the grid on the side of the blower. Rotate the ﬁlter clockwise to install and counterclockwise

to remove (FIGURE 4A). Replace all grease ﬁlters. Recirculating installations also require some duct work to divert the air out of the top or

face or side of the cabinet or custom hood or out of the side / face of the sofﬁt and back into the kitchen. Install at least 15" of vertical run of

metal duct (FIGURE 4) at the air outlet. Run the duct vertically and secure it at the relevant opening previously cut out at the top or side of

the cabinet or sofﬁt. A metal duct cover grille is also recommended. The duct work must not terminate inside the cabinet or custom hood.

cabinet

custom

hood

ceiling

duct

work

duct

work

ceiling

inca pro plus

cabinet

custom

hood

MAKE YOUR CUT-OUTS

1. Disconnect and move freestanding range from cabinet opening to provide easier access

to upper cabinet or custom hood. Put a thick, protective covering over cooktop, set-in range

or countertop to protect from damage or dirt.

2. Determine and make all necessary cuts in the wall and/or ceiling for the ductwork. Install

the ductwork before the rangehood.

3. Determine the proper location for the Power Supply Cable. Use a 1

1/4"

Drill Bit to make

this hole. Install the cable. Use caulking to seal around the hole. DO NOT turn on the

power until installation is complete.

4. Choose the knock out hole to remove for installing the power cable. Use a screwdriver

to snap off the knock out covering. (FIGURE 7 shows inside the wiring box and outside)

FIGURE 4A

inca pro plus

FIGURE 7

FOR ALL INSTALLATIONS

REMOVE ALL WHITE PLASTIC PROTECTIVE COVERING FROM HOOD, SIDE RAILS,

TRIM, GREASE RAILS AND GREASE FILTERS

FIGURE 1

FIGURE 1A

3. Install the motor kit into the back of the hood

using the 2 screws supplied with the motor kit

(Figure 4).

5. Connect the ductwork to the damper and seal all

connections with duct tape.

4. Connect the wire cable D (which is located

inside of Kit Internal 300 cfm Blower sku #; IB300

or Internal 600 cfm PRO Blower sku #; IB600).

Connect the 6 hole end to the wire box and connect

the 9 hole end to the motor (Figure 5).

FIGURE 4

6 hole

end

9 hole

end

FIGURE 5

9 hole end

FIGURE 6

6. Before installing the hood, put the damper A

(which is located inside of Kit Internal 300 cfm

Blower sku #; IB300 or Internal 600 cfm PRO

Blower sku #; IB600) (Figure 6).

9 hole end

6 hole

end

INSTALLATION WITH IB1200 INTERNAL

BLOWER (1200 cfm)

1. Install the Duct Plate B (Figure 7) which came

with the internal blower kit, on top of the rangehood

with the holes located closer to the front. Use 9

screws supplied with the blower kit.

2. Remove the white plastic covering and Install

the 4 side trim pieces (4-5) to the outside of the

hood using (14) part 9c screws, see the side trim

installation in (Figure 8).

3. Attach the blower bracket divider inside the

hood with the 2 screws into the top of the hood

and 2 screws into the back, all supplied with the

blower kit (Figure 9).

Version 07/11 - Page 9

INSTALLATION WITH IB1200 INTERNAL BLOWER (1200 cfm)

1. Install the Plate B (FIGURE 14) which came with the internal

blower kit, on top of the rangehood with the holes located closer to

the front. Use 9 screws supplied with the blower kit

2. Remove the white plastic covering and Install the 4 side trim

pieces to the outside of the hood using (16) part 9b screws, see

the side rail installation in (FIGURE 15).

3. Attach the blower bracket divider inside the hood, with the 2

screws into the top of the hood and 2 screws into the back, all

supplied with the blower kit (FIGURE 16)

FIGURE 16

FIGURE 17

4. Install the 2 motor kits into the sides of the blower bracket using

the 4 screws supplied with the motor kit. (FIGURE 17)

5. Connect the wire (FIGURE 18) that comes with the motor kit

from the side of the two motors to the connection on the inside

of the light panel in the hood. The two - 9 hole ends of the wire

are installed in the two motors, the 6 hole end is connected to

the light panel (FIGURE 11 on the previous page)

FIGURE 15

FIGURE 18

FIGURE 19

6. Install the 2 dampers on top of the hood. If you want one 10"

round duct to come out of the top of the hood, use the transition

piece (FIGURE 19) that comes with the motor kit and install with

four screws. If you want to use 2 seperate 6" round ducts, do not

use the transition.

7. Attach the hood to the cabinet using (12) 9c. screws to the

cabinet. FIGURE 20

8. Follow steps 6 - 9 on the previous page to connect ducting,

wiring, and test the electrical connection.

FIGURE 14

FIGURE 20

Version 07/11 - Page 9

INSTALLATION WITH IB1200 INTERNAL BLOWER (1200 cfm)

1. Install the Plate B (FIGURE 14) which came with the internal

blower kit, on top of the rangehood with the holes located closer to

the front. Use 9 screws supplied with the blower kit

2. Remove the white plastic covering and Install the 4 side trim

pieces to the outside of the hood using (16) part 9b screws, see

the side rail installation in (FIGURE 15).

3. Attach the blower bracket divider inside the hood, with the 2

screws into the top of the hood and 2 screws into the back, all

supplied with the blower kit (FIGURE 16)

FIGURE 16

FIGURE 17

4. Install the 2 motor kits into the sides of the blower bracket using

the 4 screws supplied with the motor kit. (FIGURE 17)

5. Connect the wire (FIGURE 18) that comes with the motor kit

from the side of the two motors to the connection on the inside

of the light panel in the hood. The two - 9 hole ends of the wire

are installed in the two motors, the 6 hole end is connected to

the light panel (FIGURE 11 on the previous page)

FIGURE 15

FIGURE 18

FIGURE 19

6. Install the 2 dampers on top of the hood. If you want one 10"

round duct to come out of the top of the hood, use the transition

piece (FIGURE 19) that comes with the motor kit and install with

four screws. If you want to use 2 seperate 6" round ducts, do not

use the transition.

7. Attach the hood to the cabinet using (12) 9c. screws to the

cabinet. FIGURE 20

8. Follow steps 6 - 9 on the previous page to connect ducting,

wiring, and test the electrical connection.

FIGURE 14

FIGURE 20

Version 07/11 - Page 9

INSTALLATION WITH IB1200 INTERNAL BLOWER (1200 cfm)

1. Install the Plate B (FIGURE 14) which came with the internal

blower kit, on top of the rangehood with the holes located closer to

the front. Use 9 screws supplied with the blower kit

2. Remove the white plastic covering and Install the 4 side trim

pieces to the outside of the hood using (16) part 9b screws, see

the side rail installation in (FIGURE 15).

3. Attach the blower bracket divider inside the hood, with the 2

screws into the top of the hood and 2 screws into the back, all

supplied with the blower kit (FIGURE 16)

FIGURE 16

FIGURE 17

4. Install the 2 motor kits into the sides of the blower bracket using

the 4 screws supplied with the motor kit. (FIGURE 17)

5. Connect the wire (FIGURE 18) that comes with the motor kit

from the side of the two motors to the connection on the inside

of the light panel in the hood. The two - 9 hole ends of the wire

are installed in the two motors, the 6 hole end is connected to

the light panel (FIGURE 11 on the previous page)

FIGURE 15

FIGURE 18

FIGURE 19

6. Install the 2 dampers on top of the hood. If you want one 10"

round duct to come out of the top of the hood, use the transition

piece (FIGURE 19) that comes with the motor kit and install with

four screws. If you want to use 2 seperate 6" round ducts, do not

use the transition.

7. Attach the hood to the cabinet using (12) 9c. screws to the

cabinet. FIGURE 20

8. Follow steps 6 - 9 on the previous page to connect ducting,

wiring, and test the electrical connection.

FIGURE 14

FIGURE 20

4. Install the 2 motor kits into the sides of the

blower bracket using the 4 screws supplied with

the motor kit (Figure 10).

7. Follow step 4 on page 13 to connect ducting,

wiring, and test the electrical connection.

FIGURE 7

FIGURE 8

FIGURE 9

FIGURE 10

5. Connect the wire cable D (which is located

inside of Kit Internal 1,200 cfm PRO Blower sku

#; IB1200). Connect the 6 hole end (A) to the wire

box and connect the 9 hole end (B-C) to the two

motors (Figure 11).

FIGURE 11

A) 6 hole end

C) 9 hole end

B) 9 hole end

A) 6 hole end

C) 9 hole end

B) 9 hole end

6. Install the 2 dampers (A) on top of the hood

(which is located inside of Kit Internal 1,200 cfm

PRO Blower sku #; IB1200). Alternatively, install

the 10" duct transition (E) (which is located inside

of Kit Internal 1,200 cfm PRO Blower sku #;

IB1200) and install with four screws (Figure 12).

Version 07/11 - Page 9

INSTALLATION WITH IB1200 INTERNAL BLOWER (1200 cfm)

1. Install the Plate B (FIGURE 14) which came with the internal

blower kit, on top of the rangehood with the holes located closer to

the front. Use 9 screws supplied with the blower kit

2. Remove the white plastic covering and Install the 4 side trim

pieces to the outside of the hood using (16) part 9b screws, see

the side rail installation in (FIGURE 15).

3. Attach the blower bracket divider inside the hood, with the 2

screws into the top of the hood and 2 screws into the back, all

supplied with the blower kit (FIGURE 16)

FIGURE 16

FIGURE 17

4. Install the 2 motor kits into the sides of the blower bracket using

the 4 screws supplied with the motor kit. (FIGURE 17)

5. Connect the wire (FIGURE 18) that comes with the motor kit

from the side of the two motors to the connection on the inside

of the light panel in the hood. The two - 9 hole ends of the wire

are installed in the two motors, the 6 hole end is connected to

the light panel (FIGURE 11 on the previous page)

FIGURE 15

FIGURE 18

FIGURE 19

6. Install the 2 dampers on top of the hood. If you want one 10"

round duct to come out of the top of the hood, use the transition

piece (FIGURE 19) that comes with the motor kit and install with

four screws. If you want to use 2 seperate 6" round ducts, do not

use the transition.

7. Attach the hood to the cabinet using (12) 9c. screws to the

cabinet. FIGURE 20

8. Follow steps 6 - 9 on the previous page to connect ducting,

wiring, and test the electrical connection.

FIGURE 14

FIGURE 20

FIGURE 12

INSTALLATION WITH REMOTE BLOWER (RB900 / RB1200) OR IN-LINE BLOWER (INLBKIT)

NOTE: FOLLOW THE INSTRUCTIONS INCLUDED WITH THE REMOTE BLOWER TO

INSTALL THE BLOWER ON THE OUTSIDE OF YOUR HOME.

1. Install the Plate B with the second wiring box

(Figure 13) which came with the remote blower kit,

on top of the rangehood. Use 9 screws supplied with

the blower kit. Remove the electrical knockout hole

on top of the plate.

2. Remove the white plastic covering and Install the

4 side trim pieces (4-5)

to the outside of the hood

using (14) part 9c screws, see the side rail installation

in (Figure 14).

FIGURE 14

3. Connect the wire coming out from the 2

wiring box

to the 6 hole end of the 1

wiring box.

Connect the wire that comes out from the black box of

the electronic board to the 9 hole end of the 1

wiring

box (Figure 15).

Version 07/11 - Page 10

INSTALLATION WITH REMOTE BLOWER (RB900 / RB1200)

OR IN-LINE BLOWER (INLBKIT)

NOTE: FOLLOW THE INSTRUCTIONS INCLUDED WITH THE

REMOTE BLOWER TO INSTALL THE BLOWER ON THE

OUTSIDE OF YOUR HOME

1. Install the Plate B (FIGURE 21) which came with the remote

blower kit, on top of the rangehood. Use 9 screws supplied with

the blower kit. Remove the electrical knockout hole on top of the

plate.

2. Remove the white plastic covering and Install the 4 side trim

pieces to the outside of the hood using (16) part 9b screws, see

the side rail installation in (FIGURE 22).

FIGURE 23

FIGURE 24

4. Feed the remote blower cable thru the knockout hole in step 1

(FIGURE 24). Connect the power supply cable from the remote

blower to the wiring box on the top ducting plate of the hood. Use

step 6 on page 8 and the diagram on page 8 (FIGURE 13)

5. Attach the hood to the cabinet using (12) 9c. screws to the

cabinet. FIGURE 25

6. Follow steps 6 - 9 on page 8 to connect ducting, wiring, and

test the electrical connection. Use the wiring box connected to

the inside wall of the hood which connects to the home power

supply thru the knockout on the side of the hood.

FIGURE 21

FIGURE 22

3. Connect the wire coming out of the wiring box on the top duct

plate to the light panel 6 hole slot connector on the front inside

of the hood (FIGURE 23)

FIGURE 25

Pass the remote blower cable through the

knockout

hole in step 1

(Figure 13,16). Connect this

cable from the remote blower to the 2

wiring box

placed on the lower surface of plate B.

5. Follow step 4 on page 13 to connect ducting,

wiring, and test the electrical connection. Use the

wiring box connected to the inside wall of the hood

which connects to the home power supply thru the

knockout on the side of the hood.

FIGURE 16

Version 07/11 - Page 10

INSTALLATION WITH REMOTE BLOWER (RB900 / RB1200)

OR IN-LINE BLOWER (INLBKIT)

NOTE: FOLLOW THE INSTRUCTIONS INCLUDED WITH THE

REMOTE BLOWER TO INSTALL THE BLOWER ON THE

OUTSIDE OF YOUR HOME

1. Install the Plate B (FIGURE 21) which came with the remote

blower kit, on top of the rangehood. Use 9 screws supplied with

the blower kit. Remove the electrical knockout hole on top of the

plate.

2. Remove the white plastic covering and Install the 4 side trim

pieces to the outside of the hood using (16) part 9b screws, see

the side rail installation in (FIGURE 22).

FIGURE 23

FIGURE 24

4. Feed the remote blower cable thru the knockout hole in step 1

(FIGURE 24). Connect the power supply cable from the remote

blower to the wiring box on the top ducting plate of the hood. Use

step 6 on page 8 and the diagram on page 8 (FIGURE 13)

5. Attach the hood to the cabinet using (12) 9c. screws to the

cabinet. FIGURE 25

6. Follow steps 6 - 9 on page 8 to connect ducting, wiring, and

test the electrical connection. Use the wiring box connected to

the inside wall of the hood which connects to the home power

supply thru the knockout on the side of the hood.

FIGURE 21

FIGURE 22

3. Connect the wire coming out of the wiring box on the top duct

plate to the light panel 6 hole slot connector on the front inside

of the hood (FIGURE 23)

FIGURE 25

FIGURE 13

wiring box

6 hole end

FIGURE 15

wiring box

6 hole end

Min. 3/4

Min.13/16

Min. 3/4

Cut out the opening in the underside of the

cabinet as shown in Figure 1a.

Installation Instructions

SECURING INSERT HOOD WITH SIDE MOUNT CLIPS

It is recommend that the Insert Hood is supported by a 3/4" wood base to insure Side Mount

Clip alignment.

Minimum cabinet opening height-16". However height may vary to allow for ducting.

Install the Insert Hood into the cabinet opening, and fully engage the four spring-loaded Side

Mount Clips onto the cabinet wood base.

Next from underneath the Insert as shown in Figure A, locate the screw in each of the Side

Mount Clips.

To lock the Insert Hood into position, tighten the screw for each of four Side Mount Clips.

Next from underneath the Insert Hood Place the four plastic stoppers (10) as shown in Figure B.

Outside

Hood

Dimension

Model # X Y

30" x 19" INPL3019SSNB-B 28-5/8" 19-7/8"

36" x 19" INPL3619SSNB-B 34-3/4" 19-7/8"

36" x 22" INPL3622SSNB-B 34-3/4" 22-7/8"

42" x 19" INPL4219SSNB-B 40-3/4" 19-7/8"

48" x 19" INPL4819SSNB-B 46-3/4" 19-7/8"

48" x 22" INPL4822SSNB-B 46-3/4" 22-7/8"

Two people may be

required for installation.

Min. 24" Min. 30"

Installation Instructions

SECURING INSERT HOOD WITHOUT SIDE MOUNT CLIPS

Outside

Hood

Dimension

Model # X Y

30" x 19" INPL3019SSNB-B 28-5/8" 19-7/8"

36" x 19" INPL3619SSNB-B 34-3/4" 19-7/8"

36" x 22" INPL3622SSNB-B 34-3/4" 22-7/8"

42" x 19" INPL4219SSNB-B 40-3/4" 19-7/8"

48" x 19" INPL4819SSNB-B 46-3/4" 19-7/8"

48" x 22" INPL4822SSNB-B 46-3/4" 22-7/8"

Min. 3/4

Min.13/16

Min. 3/4

Cut out the opening in the underside of the

cabinet as shown in Figure 2a.

It is recommend that the Insert Hood is supported by a 3/4" wood base.

Minimum cabinet opening height-16". However height may vary to allow for ducting.

Install the Insert Hood into the cabinet opening.

Insert Hood attaches on the short side of the cabinet using screws (purchased separately).

From inside Insert Hood as shown in Figure B and C, secure the Insert Hood with three

screws into wood support /cabinet framing.

Next from underneath the Insert Hood Place the four plastic stoppers (10) as shown in

Figure B.

Min. 24" Min. 30"

Two people may be

required for installation.

a b

Secure the Insert Hood with six screws (9d) on the front side as shown above in gure A.

Place the six Stopper (10) on the front side as shown above in gure B.

Installation of wiring connection

Remove the wiring electrical knockout using a

at-blade screwdriver. Feed the Power Supply

Cable through the electrical knockout.

Connect the Power Supply Cable to the ran-

gehood. Attach the White lead of the power

supply (A) to the White lead of the rangehood

(D) with a twist-on type wire connector. Attach

the Black lead of the power supply to the Black

lead of the rangehood (B) with a twist-on type

wire connector (C). Connect the Green (E)

(Green and Yellow) ground wire under the

Green grounding screw.

Replace the eld wiring compartment cover

and the grease lters.

Connect the ductwork to the damper and seal

all connections with duct tape.

Turn the power supply on. Turn on the blower

and light. If the rangehood does not operate,

check that the circuit breaker is not tripped

or the house fuse blown. If the unit still does

not operate, disconnect the power supply and

check that the wiring connections have been

made properly.

Reattach the eld wiring compartment cover.

Hood wiring

Attach each

charcoal

lter to the

black grid on

each side of

the blower.

Press the

charcoal

lter tightly

to the black

grid on the

blower side

and rotate

the lter

For Non-Ducted Recirculation

Option

Required Activated Charcoal Filter

Accessory - sku # - FILTER1

(purchased separately).

When used in recirculation mode,

to Reduce the Risk of Fire and

Shock use only conversion kit

Model FILTER 1.

clockwise (towards the front of the insert hood)

until it locks into place. Turn counterclockwise

(towards the back of the insert hood) to remove.

Replacing Activated Charcoal Filter

The Activated Charcoal Filters are not washable

and cannot be regenerated, and should be

replaced approximately every 4 months of

operation, or more frequently with heavy usage.

Remove the charcoal lter by rotating it

clockwise (backwards) until it unlocks from the

motor housing and pull o sideways.

To reinsert each charcoal lter, place up against

the side of the blower and push it inward. Then

turn the charcoal lter clockwise (forward) until it

ts into place.

Bae Filter

Before installing the lters (6), tighten the 2 knobs

(7) with 2 screws (9e).

Use two hands to insert and remove the lters.

Hook the Grease rail (8) positioning it inside

the hood. Is possible wash and reposition

inside the hood.

Rangehood Control Panel

The control panel is located in the center of the

hood bottom.

Light On/O Button (A)

On/O switch for the lights. Position "0" turns the

lights O, turning the switch to the right is On.

Blower On/O Button (B)

On/O switch for the blower. Move the dial to the

right to turn the blower ON and vary the speed of

the blower. Turn to the left at "0" to turn it OFF.

For Best Result

Start the rangehood several minutes before

cooking to develop proper airow. Allow the unit

to operate for several minutes after cooking is

complete to clear all smoke and odors from the

kitchen.

Cleaning

The stainless steel grease lters and grease rail

should be cleaned frequently in hot detergent

solution or washed in the dishwasher. Clean

exterior surfaces with a commercially available

stainless steel cleaner. Abrasives and scouring

agents can scratch stainless steel nishes and

should not be used to clean nished surfaces.

Make sure the grease lters are completely dry

with no water present before re-installing into

hood.

Grease rail and Grease Filter Installation /

Removal.

Remove the plastic from the lter, the knobs

need to be installed onto the lter with 2

screws to each lter.

Version 07/11 - Page 11

Light On/Off Button (A)

On/Off switch for the halogen lights. Position "0" turns the lights off,

turning the switch to the right one click is the dimmer position, and

the next click to the right is full power

Blower On/Off Button (B)

On/Off switch for the blower. Move the dial to the right to turn the

blower ON and vary the speed of the blower. Turn to the left at "0"

to turn it OFF.

For Best Result

Start the rangehood several minutes before cooking to develop proper

airﬂow. Allow the unit to operate for several minutes after cooking is

complete to clear all smoke and odors from the kitchen.

Cleaning

The stainless steel grease ﬁlters and grease rail should be cleaned

frequently in hot detergent solution or washed in the dishwasher.

Clean exterior surfaces with a commercially available stainless steel

cleaner. Abrasives and scouring agents can scratch stainless steel

ﬁnishes and should not be used to clean ﬁnished surfaces.

Grease rail and Grease Filter Installation / Removal

Remove the plastic from the ﬁlter, the knobs need to be installed

onto the ﬁlter with 2 screws to each ﬁlter

Install the grease rail into the back of the hood, into the slots on the

inside ﬂoor of the rear of the hood. The Grease ﬁlters should be

installed before operating the rangehood. To install the ﬁlters, use the

two knobs (in FIGURE 28) to hold the ﬁlter and insert the ﬁlter into

the front edge of the hood with the knobs facing out into the spring

loaded slot. Install the other end of the ﬁlter above the grease rail in

the back of the hood.

USE AND CARE INFORMATION

This rangehood system is designed to remove smoke, cooking vapors

and odors from the cooktop area.

Rangehood Control Panel

The control panel is located in the center of the hood bottom. The

position and function of each control button are indicated in FIGURE

FIGURE 28

Replacing the Halogen Lamp

Before you begin, make sure that the rangehood is turned off and

that the other lamps have had sufﬁcient time to cool. Halogen lamps

burn extremely hot and serious injury could result from touching a hot

lamp. Press and twist the lamp to remove. Then remove the lamp

and replace with a new lamp.

WIRING DIAGRAM

This rangehood uses 45 watt PAR16

Halogen Lamps.

FIGURE 27

FIGURE 26

ALL INSTALLATIONS

1. Use a drill to install side rails on the inside rangehood walls to

line the inside hood wall with stainless, 2 and 3 in FIGURE 26 with

9a. screws, 4 screws total.

BLK

WHT

R11B41

LIGHT CONTROL

OFF / HALF LIGHT / ON

Y-G

RED

WIRING BOX

WHT

BLK

ORG

WHT

VLT

Y-G

LINE IN

120Vac

60Hz ~

Y-G

BLU

123

654

789

123

654

987

RED

M8 4V

120V ~

WHT

BRW

BLU

BLK

ORG

BLU

BLK

Y-G

ON/OFF MOTOR

SPEED CONTROL

BLKBLK

BLU

123

654

789

123

654

987

RED

M8 4V

120V ~

BLU

Y-G

WHT

BRW

BLKBLK

BLU

123

654

123

654

BLK

ORG

Y-G

BLU

WHT

BLK

Y-G

WIRING BOX FOR

REMOTE BLOWER

WHT

REMOTE

BLOWER

123

654

WHT

Y-G

BLKBLK

Y-G

Gu10 self-ballasted led lamps

– listed in accordance with ul

1993/nmx-j-578/1-ance/csa

c22.2 No. 1993

Lighting unit

• Replace the lamp with a new one of the same type,

making sure that you insert the two pins properly

into the housings on the lamp holder.

Install the grease rail into the back of the hood,

into the slots on the inside oor of the rear of the

hood. The Grease lters should be installed before

operating the rangehood. To install the lters, use

the two knobs to hold the lter and insert the lter

into the front edge of the hood with the knobs

facing out into the spring loaded slot. Install the

other end of the lter above the grease rail in the

back of the hood.

A B

Wiring Diagram

 































































 





 



 











































































































































January 4, 2016

FABER CONSUMER WARRANTY & SERVICE

All Faber products are warranted against any defect in materials or workmanship for the original purchaser

for a period of 1 year from the date of original purchase (requires proof of purchase). This warranty covers

labor and replacement parts. Faber, at its option, may repair or replace the product or components

necessary to restore the product to good working condition. To obtain warranty service, contact the dealer

from whom you purchased the range hood, or the local Faber distributor. If you cannot identify a local Faber

distributor, contact us at (508) 358-5353 for the name of a distributor in your area.

The following is not covered by Faber's warranty:

1. Service calls to correct the installation of your range hood, to instruct you how to use your range hood, to

replace or repair house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace range hood light bulbs, fuses or filters. Those consumable parts are

excluded from warranty coverage.

3. Repairs when your range hood is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation,

installation not in accordance with electrical or plumbing codes or Faber documentation, or use of products

not approved by Faber.

5. Replacement parts or repair labor costs for units operated outside the United States or Canada, including

any non-UL or C-UL approved Faber range hoods.

6. Repairs to the hood resulting from unauthorized modifications made to the range hood.

7. Expenses for travel and transportation for product service in remote locations and pickup and delivery

charges. Faber range hoods should be serviced in the home.

THIS WARRANTY DOES NOT ALLOW RECOVERY OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, PERSONAL INJURY/WRONGFUL

DEATH OR LOST PROFITS FABER WARRANTY IS LIMITED TO THE ABOVE CONDITIONS AND TO THE WARRANTY PERIOD

SPECIFIED HEREIN AND IS EXCLUSIVE. EXCEPT AS EXPRESSLY SPECIFIED IN THIS AGREEMENT, FABER DISCLAIMS ALL

EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS, AND WARRANTIES INCLUDING, WITHOUT LIMITATION, ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

This warranty gives you specific legal rights that may vary from state to state.

Model#: ______________________________ Serial #: _____________________________

VEUILLEZ LIRE ET CONSERVER LA PRÉSENTE NOTICE AVANT DE COMMEN-

CER L'INSTALLATION DE LA HOTTE DE CUISINE

AVERTISSEMENT:-POUR RÉDUIRE LE RISQUE D'UN FEU DE GRAISSE SUR LA TABLE DE CUISSON:

a) Ne laissez jamais sans surveillance les éléments de la surface de cuisson à température élevée. Les

bouillonnements excessifs peuvent provoquer de la fumée et les débordements de graisse peuvent

s'enflammer. L'huile doit être chauffée lentement, à une température basse ou moyenne.

b) Assurez-vous de toujours mettre en marche le ventilateur de la hotte lorsque vous cuisinez à tem-

pérature élevée ou préparez un mets flambé (p.ex. crêpes Suzette, cerises jubilé, bœuf flambé).

c) Nettoyez régulièrement les ventilateurs d'aspiration. Assurez-vous de ne pas laisser de la graisse

s'accumuler sur le ventilateur ou le filtre.

d) Utilisez toujours des poêles et casseroles de la taille appropriée. Utilisez toujours des ustensiles de

cuisine de la taille adaptée à celle de l'élément chauffant.

AVERTISSEMENT: - POUR PRÉVENIR LES BLESSURES EN CAS DE FEU DE GRAISSE SUR LA TABLE DE

CUISSON, SUIVEZ LES RECOMMANDATIONS SUIVANTES*:

a) ÉTOUFFEZ LES FLAMMES à l'aide d'un couvercle hermétique, d'une plaque à biscuits ou d'un plateau

métallique, puis éteignez le brûleur. FAITES ATTENTION AUX BRÛLURES. Si le feu ne s'éteint pas

immédiatement, QUITTEZ LES LIEUX ET APPELEZ LES POMPIERS.

b) NE PRENEZ JAMAIS UNE CASSEROLE EN FLAMME - Vous pourriez vous brûler.

c) N'UTILISEZ JAMAIS DE L'EAU, ni un linge à vaisselle ou un torchon mouillé, pour éteindre le feu. Cela

pourrait provoquer une violente explosion de vapeur.

d) Utilisez un extincteur UNIQUEMENT si:

1. Vous êtes certain qu'il s'agit d'un extincteur de classe ABC et que vous connaissez bien son mode

d'emploi.

2. Le feu est de faible intensité et se limite à l'endroit où il a démarré.

3. Les pompiers ont déjà été appelés.

4. Une voie de sortie se trouve derrière vous pendant que vous éteignez les flammes

* D'après le guide «Kitchen Firesafety Tips» publié par la NFPA aux États-Unis

AVERTISSEMENT - POUR RÉDUIRE LE RISQUE D'INCENDIE OU DE CHOC ÉLECTRIQUE, n'utilisez jamais

ce ventilateur en association avec un dispositif de réglage de vitesse à semi-conducteurs.

AVERTISSEMENT - POUR RÉDUIRE LES RISQUES D'INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURE

CORPORELLE, RESPECTEZ LES INSTRUCTIONS SUIVANTES :

a. Utilisez cet appareil uniquement de la façon prévue par le fabricant. Pour toute question, commu-

niquez avec le fabricant.

b. Avant de procéder à l'entretien ou au nettoyage de l'appareil, coupez l'alimentation au niveau du

panneau électrique et verrouillez-le pour vous assurer que l'électricité n'est pas rétablie acciden-

tellement.

S'il n'est pas possible de verrouiller le dispositif d'interruption de l'alimentation, affichez de façon

ferme et bien visible un avis de danger, par exemple à l'aide d'une étiquette sur le panneau.

ATTENTION : Destiné à un usage de ventilation générale uniquement. N'utilisez pas ce dispositif pour

l'aspiration de vapeurs ou de matériaux dangereux ou explosifs.

AVERTISSEMENT - POUR RÉDUIRE LES RISQUES D'INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURE

CORPORELLE, RESPECTEZ LES INSTRUCTIONS SUIVANTES:

1. L'installation et le branchement électrique doivent être réalisés par un technicien qualifié et

conformément à tous les codes et normes en vigueur, incluant ceux concernant la construction

à l'épreuve du feu.

2. Afin de garantir une combustion et une évacuation adéquates des gaz par les conduites de la

cheminée des appareils à combustion, une bonne aération est nécessaire pour éviter le refou-

lement. Respectez les lignes directrices fournies par le fabricant du matériel chauffant, ainsi que

les normes de sécurité comme celles publiées par la National Fire Protection Association (NFPA)

et la American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) aux

États-Unis, ainsi que les codes en vigueur dans votre région.

3. Lorsque vous faites une ouverture ou percez dans un mur ou le plafond, veillez à ne pas endom-

mager les fils électriques ou d'autres dispositifs cachés.

4. Les ventilateurs canalisés doivent toujours être raccordés à l'extérieur.

TOUTE OUVERTURE DANS LE MUR OU LE PLANCHER À PROXIMITÉ DE LA HOTTE

DOIT ÊTRE SCELLÉE.

Un espace libre d'au moins 24" est requis entre le bas de la hotte et la surface de cuisson ou le comptoir.

Cette hotte a été homologuée par l'UL à cette distance de la surface de cuisson.

L’espace libre minimal requis peut-être plus grand, selon la réglementation en matière de construction de

votre région. Pour les cuisinières à gaz et les cuisinières combinées, un espace minimal de 30" est recommandé

et pourrait être exigé.

Les armoires suspendues de chaque côté de l'appareil doivent se trouver à au moins 18" de la surface de

cuisson ou du comptoir. Consultez la notice d'installation de la surface de cuisson ou de la cuisinière fournie

par le fabricant avant de pratiquer des ouvertures.

INSTALLATION DANS UNE MAISON MOBILE L'installation de cette hotte doit être conforme à la Partie 3280

de la norme Manufactured Home Construction and Safety Standards, Title 24 CFR (précédemment la partie

280 de la norme Federal Standard for Mobile Home Construction and Safety, Title 24, HUD). Consultez la

fiche technique électrique.

CRITÈRES DE VENTILATION

Déterminez quelle méthode de ventilation est mieux adaptée à votre application. Les conduits peuvent

passer par le mur ou le toit.

Pour garantir une meilleure efficacité, la longueur des conduits et le nombre de coudes doivent être le plus

limités que possible. Le diamètre des conduits devrait être uniforme. N'installez pas deux coudes ensemble.

Utilisez un ruban pour canalisations afin de sceller tous les joints du système de conduits. Utilisez un calfeutrage

pour sceller les ouvertures dans le mur extérieur ou le plancher, autour du clapet.

Il n'est pas recommandé d'utiliser des conduits exibles. Les conduits exibles provoquent une contre-pres-

sion et de la turbulence qui diminuent grandement l'ecacité de l'appareil.

Assurez-vous que l'espace libre dans le mur ou le plancher est suffisant pour le conduit d'évacuation avant

de pratiquer les ouvertures. Ne coupez jamais une poutre ou un chevron, sauf si c'est absolument nécessaire.

S'il s'avère nécessaire de couper une poutre ou un chevron, la construction d'un renforcement est requise.

AVERTISSEMENT - Pour réduire le risque d'incendie, utilisez uniquement des conduits métalliques.

ATTENTION - Pour réduire le risque d'incendie et pour évacuer adéquatement l'air, assurez-vous de

raccorder les conduits à l'extérieur – Ne diffusez pas l'air d'évacuation dans des espaces à l'intérieur

des murs ou du plafond, ou encore à l'intérieur d'un grenier, d'une galerie technique ou d'un garage.

La page charge ...

Faber Inca Pro 30 X 19 SS NB-B Guide d'installation

Marque: Faber

Modèle: Inca Pro 30 X 19 SS NB-B

Catégorie: Hottes

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Faber Inca Pro 30 X 19 SS NB-B Installation guide

Documents connexes

Autres documents

XO T18 Ducted Hood Manuel utilisateur