XO T18 Ducted Hood Manuel utilisateur

I worked really hard

on this manual - so

please read it...

XOT UNDER CABINET

MODELS XOT24SC, XOT30SC, XOT36SC, XOT42SC, XOT48SC

XOT1830SC, XOT1836SC, XOT1842SC,

XOT1848SC

Online @ https://xoappliance.com/priority-service-for-your-xo-product/

Or by phone 973-403-8900

CONGRATULATIONS

REGISTRATION HELPS YOU BY -

It’s for your

ow n go od.. .

Honest.

GETTING READY

Safety and Precautions

Planning Ductwork

Install Examples

Dimensions

THE INSTALL

Mounting Height

Top or Rear Exhaust

Installing

Electrical Connections

MAINTENANCE

Filters

Cleaning

Recirculation

Light Replacement

OPERATING

The Push Button Controls

CCC Make Up Air Conversion

PARTS & WARRANTY

24 - 25

26 - 27

5 - 13

14 - 21

22 - 23

THIS HOOD IS DESIGNED TO USE A 6” ROUND DUCT -

IT MAY BE TRANSITIONED TO A 3-1/4” X 10” RECTANGULAR DUCT

NEVER REDUCE DUCT SIZE. UNDERSIZED DUCTING SEVERELY RESTRICTS AIR

FLOW AND HARMS PERFORMANCE.

(Example: the area of a 6” Duct is more than TWICE that of a 4” Duct)

KEEP DUCT RUNS AS SHORT AND STRAIGHT AS POSSIBLE.

AVOID USING FLEXIBLE METAL DUCTING IF RUN IS LONGER THAN 6’.

NEVER USE PLASTIC DUCTING.

USE SMOOTH BORE METAL DUCTING.

MINIMIZE THE NUMBER OF FITTINGS (see chart).

WHEN YOU MUST USE FITTINGS, TRY TO SEPARATE THEM WITH SECTIONS OF

3’ OR MORE OF STRAIGHT DUCT.

ALWAYS FOLLOW THE MANUFACTURER’S GUIDELINES FOR THE COOKING

EQUIPMENT YOU ARE VENTING.

IF MAKE UP AIR CONTROL DAMPERS ARE REQUIRED, POSITION THE SENSOR

IN A STRAIGHT RUN OF DUCT IDEALLY WITH 3’ OF STRAIGHT DUCT BETWEEN

EACH SIDE OF THE SENSOR AND A DUCT FITTING. REMEMBER TO INCLUDE

POWER AND CONTROL WIRING FOR THIS IN YOUR PLANS.

ADHERE TO ALL LOCAL BUILDING CODES AND ORDINANCES.

USE THE WORKSHEET THAT FOLLOWS TO HELP CALCULATE THE

TOTAL EQUIVILENT FEET OF YOUR DUCT RUN.

TOTAL EQUIVILENT FEET SHOULD BE LESS THAN 100’.

CAUSING AIR TO CHANGE DIRECTION CAUSES TURBULENCE AND RESTRICTS FLOW IN

A SYSTEM.

IF USING FLEXIBLE METAL DUCT - INCREASE ALL MULTIPLIERS BY 50% (12 BECOMES

18 - ETC.)

THIS EASY TO USE WORKSHEET IS FOR 600 CFM OR LESS.

UNDER “QTY USED” ENTER HOW OF EACH SECTION YOU WILL BE USING.

IN THE FIRST TWO ROWS - ENTER HOW MANY FEET OF EACH TYPE OF STRAIGHT DUCT

YOU WILL BE USING (I.E. FOR 20 FT ENTER 20, FOR 30FT ENTER 30).

ENTER THE NUMBER OF EACH TYPE OF TURN YOU ARE USING AND THE TYPE OF END CAP.

MULTIPLY ACROSS EACH ROW THE “MULTIPLIER” x “QTY USED” TO GET THE EQUIVALENT

FEET FOR THOSE COMPONENTS.

ADD UP ALL THE VALUES IN THE “EQUIVALENT FEET” COLUMN.

DUCT PIECE DESCRIPTION MULTIPLIER QTY USED EQUIVALENT

FEET

1’ of 6” Round Duct

1’ of 3 1/4“ x 10” Rect. Duct

6” 90 Degree Elbow

6” 45 Degree Elbow

3 1/4” x 10” 90 Degree

3 1/4” x 10” 45 Degree

3 1/4” x 10” Side 90 Degree

3 1/4” x 10” x 6” Round

3 1/4” x 10” x 6” 90 Degree

6” Round Wall Cap w Damper

3 1/4” x 10” Wall Cap w Damper

6” Round Roof Cap

TOTAL EQUIVALENT FEET SHOULD BE LESS THAN 100

VENTED

RECIRCULATION

WALL EXHAUST ROOF EXHAUST

WALL EXHAUST GRID EXHAUST

RECIRCULATION EXHAUST

MUST BE RETURNED TO THE

SPACE

MODEL A B

XOT24SC

XOT30SC

XOT36SC

XOT42SC

XOT48SC

XOT1830SC

XOT1836SC

XOT1842SC

XOT1848SC

RECOMMENDED

MOUNTING HEIGHT

ABOVE GAS AND

ELECTRIC COOKTOPS

All range hoods have a recommended range of installation height over the cooking

surface.

It is important to install the hood at the proper mounting height. Hoods mounted too

low could result in heat damage and fire hazard; while hoods mounted too high will

be hard to reach and will lose its performance and efficiency.

TO CONVERT THE UNIT FROM TOP EXHAUST TO REAR EXHAUST

FOLLOW THESE SIMPLE STEPS:

1. Unplug the quick disconnect coupling that supplies power to the motor.

2. Remove the twelve (12) screws that fasten the blower assembly and filler

plate to the hood.

3. Remove the blower assembly and filler plate, invert 180° as shown and

fasten in place using the twelve (12) screws previously removed.

4. Reconnect the quick disconnect plug.

VENTED

MODE

• This product can be installed in 2

- Mounting the hood in the lower part of the shelf:

1 type installation

- Mounting the hood on the wall:

2 type installation.

• Mounting the hood in the lower part of the shelf:

- Check that the screws used to mount the hood are suitable suitable for the type of material

you are mounting to.

Fig.B,(considering the recommended

distance from the cooker top).

A without tightening them completely (Fig.A).

- Position the hood on the screws, under the cabinet (Fig.A), tighten/fasten the 4 screws A

B.

• Mounting the hood on the wall:

Fig.B (considering the recommended distance from

the cooker top).

A without tightening them completely along with the plugs Fig.A.

- Hang the hood on the wall, aligning it in a horizontal position and tighten/fasten the 2 screws

A B (Fig.A).

For the various installations use screws and screw anchors suited to the type of wall (e.g.

reinforced concrete, plasterboard, etc.). If the screws and screw anchors are provided with

•

support elements. If this is not the case, install a support structure made up from 2 by 4 inch

cross members in correspondence with the screw anchorage points.

La page charge ...

XO T18 Ducted Hood Manuel utilisateur

XO T18 Ducted Hood Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents