XO M30GC Wall Mount Chimney Range Hood Manuel utilisateur

I worked really hard

on this manual - so

please read it...

XOM WALL MOUNT

MODELS XOM30GC - XOM36GC

- 3 -

When buying any XO appliance

you can be confident you have chosen a

high quality, innovative and stylish product

from a company that cares about you!

If you require service or have questions,

there are 2 ways to contact our ventilation experts;

Online @ https://xoappliance.com/priority-service-for-your-xo-product/

Or by phone 973-403-8900

CONGRATULATIONS

on purchasing your XO.

Before you proceed, take just a

moment to register your XO at:

www.xoappliance.com/register-your-product/

REGISTRATION HELPS YOU BY -

Ensuring warranty coverage should you need service

Providing ownership verification for insurance purposes

Let’s XO notify you in the event of product changes or recalls.

- 4 -

It’s for your

own good...

Honest.

please read and follow

all safety instructions

where things are

GETTING READY

Safety and Precautions

Planning Ductwork

Install Examples

Dimensions

THE INSTALL

Mounting Height

Installing

Electrical Connections

MAINTENANCE

Filters

Cleaning

Recirculation

Light Replacement

OPERATING

The Push Button Controls

CCC Make Up Air Conversion

PARTS & WARRANTY

17 - 18

19 - 20

5 - 11

12 - 14

15 - 16

- 5 -

safety first

IMPORTANT SAFETY INSTRUCTIONS

FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

IMPORTANT: Save these Instructions for the Local Electrical Inspectors use.

INSTALLER: Please leave these Instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

Take care when using cleaning agents or detergents.

Suitable for use in household cooking area.

WARNING - To reduce the risk of ﬁre or electric shock, do not use this fan with any

Solid-State Speed Control Device.

CAUTION - To reduce risk of ﬁre and to properly exhaust air, be sure to duct air out-

side – Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl

spaces, or garages.

CAUTION - For Residential Kitchen ventilating use only. Do not use to exhaust haz-

ardous or explosive materials and vapors.

CAUTION - To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. oﬀ power unit.

CAUTION - Please read speciﬁcation label on product for further information and

requirements.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the manufacturer. If you have questions,

contact the manufacturer.

B. Before servicing or cleaning unit, switch power oﬀ at service panel and lock the ser-

vice disconnecting means to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a promi-

nent warning device, such as a tag, to the service panel.

WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause smoking and

- 6 -

greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking with high heat.

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on

fan or ﬁlter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface

element.

E. Keep fan, ﬁlters and grease laden surface clean.

F. Use high range setting on range only when necessary. Heat oil slowly on low to me-

dium setting.

G. Don’ t leave range unattended when cooking.

H. Always use cookware and utensils appropriate for the type and amount oﬀ food be-

ing prepared.

WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE

TOP GREASE FIRE, OBSERVE THE FOLLOWING:

A. SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet, or metal tray, then turn oﬀ

the burner. BE CAREFUL TO PREVENT BURNS. If the ﬂames do not go out immediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN – You may be burned.

C. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion

will result.

D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. The ﬁre is small and contained in the area where it started.

3. The ﬁre department is being called.

4. You can ﬁght the ﬁre with your back to an exit.

aBased on “kitchen ﬁresafety tips” published by NFPA.

Proper maintenance of the Range Hood will assure proper performance of the unit.

INSTALLATION INSTRUCTIONS

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be done by qualiﬁed person(s) in accord-

ance with all applicable codes and standards, including ﬁre-rated construction.

B. Suﬃcient air is needed for proper combustion and exhausting of gases through the

ﬂue (chimney) of fuel burning equipment to prevent back drafting. Follow the heat-

ing equipment manufacturer’s guideline and safety standards such as those pub-

lished by the National Fire Protection Association (NFPA), and the American Society

for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local

- 7 -

code authorities.

C. When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

D. Ducted fans must always be vented to the outdoors.

E. This unit must be grounded.

WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

WARNING - UNDER CERTAIN CIRCUMSTANCES DOMESTIC APPLIANCES MAY BE

DANGEROUS.

A. Do not check ﬁlters with hood working.

B. Do not touch the lamps after a prolonged use of the appliance.

C. No food must be cooked ﬂambè underneath the hood.

D. The use of an unprotected ﬂame is dangerous for the ﬁlters and could cause ﬁres.

E. Watch constantly while frying food in order to avoid cooking oil ﬂare ups.

F. Before performing any maintenance operation, disconnect the hood from the

electrical service.

The manufacturers will not accept any responsibility for possible damages, because

of failure to observe the above instructions.

- 8 -

THIS HOOD IS DESIGNED TO USE A 6” ROUND DUCT -

IT MAY BE TRANSITIONED TO A 3-1/4” X 10” RECTANGULAR DUCT

NEVER REDUCE DUCT SIZE. UNDERSIZED DUCTING SEVERELY RESTRICTS AIR

FLOW AND HARMS PERFORMANCE.

(Example: the area of a 6” Duct is more than TWICE that of a 4” Duct)

KEEP DUCT RUNS AS SHORT AND STRAIGHT AS POSSIBLE.

AVOID USING FLEXIBLE METAL DUCTING IF RUN IS LONGER THAN 6’.

NEVER USE PLASTIC DUCTING.

USE SMOOTH BORE METAL DUCTING.

MINIMIZE THE NUMBER OF FITTINGS (see chart).

WHEN YOU MUST USE FITTINGS, TRY TO SEPARATE THEM WITH SECTIONS OF

3’ OR MORE OF STRAIGHT DUCT.

ALWAYS FOLLOW THE MANUFACTURER’S GUIDELINES FOR THE COOKING

EQUIPMENT YOU ARE VENTING.

IF MAKE UP AIR CONTROL DAMPERS ARE REQUIRED, POSITION THE SENSOR

IN A STRAIGHT RUN OF DUCT IDEALLY WITH 3’ OF STRAIGHT DUCT BETWEEN

EACH SIDE OF THE SENSOR AND A DUCT FITTING. REMEMBER TO INCLUDE

POWER AND CONTROL WIRING FOR THIS IN YOUR PLANS.

ADHERE TO ALL LOCAL BUILDING CODES AND ORDINANCES.

USE THE WORKSHEET THAT FOLLOWS TO HELP CALCULATE THE

TOTAL EQUIVILENT FEET OF YOUR DUCT RUN.

TOTAL EQUIVILENT FEET SHOULD BE LESS THAN 100’.

a few simple rules to plan your

ductwork

1

12

7

14

8

33

2

4

24

33

- 9 -

1

12

7

14

8

33

2

4

24

33

CAUSING AIR TO CHANGE DIRECTION CAUSES TURBULENCE AND RESTRICTS FLOW IN

A SYSTEM.

IF USING FLEXIBLE METAL DUCT - INCREASE ALL MULTIPLIERS BY 50% (12 BECOMES

18 - ETC.)

THIS EASY TO USE WORKSHEET IS FOR 600 CFM OR LESS.

UNDER “QTY USED” ENTER HOW OF EACH SECTION YOU WILL BE USING.

IN THE FIRST TWO ROWS - ENTER HOW MANY FEET OF EACH TYPE OF STRAIGHT DUCT

YOU WILL BE USING (I.E. FOR 20 FT ENTER 20, FOR 30FT ENTER 30).

ENTER THE NUMBER OF EACH TYPE OF TURN YOU ARE USING AND THE TYPE OF END CAP.

MULTIPLY ACROSS EACH ROW THE “MULTIPLIER” x “QTY USED” TO GET THE EQUIVALENT

FEET FOR THOSE COMPONENTS.

ADD UP ALL THE VALUES IN THE “EQUIVALENT FEET” COLUMN.

DUCT PIECE DESCRIPTION MULTIPLIER QTY USED EQUIVALENT

FEET

1’ of 6” Round Duct

1’ of 3 1/4“ x 10” Rect. Duct

6” 90 Degree Elbow

6” 45 Degree Elbow

3 1/4” x 10” 90 Degree

3 1/4” x 10” 45 Degree

3 1/4” x 10” Side 90 Degree

3 1/4” x 10” x 6” Round

3 1/4” x 10” x 6” 90 Degree

6” Round Wall Cap w Damper

3 1/4” x 10” Wall Cap w Damper

6” Round Roof Cap

TOTAL EQUIVALENT FEET SHOULD BE LESS THAN 100

estimating total equivalent feet in

a duct

- 10 -

VENTEDRECIRCULATION

WALL EXHAUST ROOF EXHAUST

GRID EXHAUST

RECIRCULATION

EXHAUST MUST BE RE-

TURNED TO THE SPACE

typical installation examples

11-1/4"

2-3/16"

24-3/4"

A

Max 1117.6 - Min. Extractor 730 - Min Filtering 812.5

Max 44 - Min. Extractor 28-3/4" - Min Filtering 32"

11-1/4"

19-5/16"

- 11 -

11-1/4"

2-3/16"

24-3/4"

A

Max 1117.6 - Min. Extractor 730 - Min Filtering 812.5

Max 44 - Min. Extractor 28-3/4" - Min Filtering 32"

11-1/4"

19-5/16"

 Front of hood  Side of hood

 Top of hood

dimensions

MODEL A

XOM30GC 30”

XOM36GC 36”

 Duct cover removed

- 12 -

27”to32”

RECOMMENDED

MOUNTING HEIGHT

ABOVE GAS AND

ELECTRIC COOKTOPS

highs and lows

All range hoods have a recommended range of installation height over the cooking

surface.

It is important to install the hood at the proper mounting height. Hoods mounted too

low could result in heat damage and fire hazard; while hoods mounted too high will

be hard to reach and will lose its performance and efficiency.

- 13 -

27”to32”

installation

A

B







MOUNT TO THE WALL:

Drill the holes A respecting the distances

indicated (Fig.1). Fix the appliance to

the wall and align it in horizontal posi-

tion to the wall units. When the appli-

ance has been adjusted, deﬁnitely ﬁx

the hood using the screws A (Fig.3). For

the various installations use screws and

screw anchors suited to the type of wall

(e.g. reinforced concrete, plasterboard,

etc.). If the screws and screw anchors are

provided with the product, check that

they are suitable for the type of wall on

which the hood is to be ﬁxed.

INSTALL THE DUCT COVER:

Adjust the width of the support bracket of the upper ﬂue (Fig.2). Then ﬁx it to the ceiling

using the screws A (Fig.3) in such a way that it is in line with your hood and respecting

the distance from the ceiling indicated in Fig.1. Connect the ﬂange C to the air exhaust

hole using a connection pipe (Fig. 3). Insert the upper ﬂue into the lower ﬂue. Fix the

lower ﬂue to the hood using the screws B provided (Fig.3), extract the upper ﬂue up to

the bracket and ﬁx it with the screws B (Fig.2).

IMPORTANT - The range hood must be secured to wall studs or use drywall

anchors capable of supporting 75 lbs.

- 14 -

1. Route the power cord to the junction box.

2. Using listed conduit fittings and connectors, connect the power supply to the box and

each line to the appropriate wire following this color convention:

BLACK = HOT LEG

WHITE = NEUTRAL

GREEN/YELLOW = GROUND

Polarity must be observed.

Unit must be properly grounded.

Use a double throw disconnect switch.

3. Replace the box cover

Replace the Anti-grease flters.

All wiring must be in compliance with national electrical code, ANSI/NFPA 70-1999

and all local codes and regulations.

electrical connection

A Remove the central screw and lift the electrical plant box.

B Remove the 3 fixed screws. Then position the electrical box so it is in line with the holes

of the previously removed screws and tighten.

C Pay attention that the tear tape of the electrical box is inside the slot and then tighten screw.

A B

C D

D

- 15 -

maintenance

Regular cleaning and maintenance is the key to long life and peak performance of any

equipment.

•Theanti-greaselter is used to trap any grease particles suspended in the air, therefore

is subject to saturation (the time it takes for the lter to become saturated depends on the

way in which the appliance is used). The greaseltersshould be cleaned frequently. Use a

warm detergent solution. Grease lters are a dishwasher safe.

- To prevent potential re hazards, the anti-

grease lters should be washed a minimum

of every 2 months (it is possible to use the

dishwasher for this task).

- After a few washes, the colour of the lters

may change. This does not mean they have to

be replaced. If the replacement and washing

instructions are not followed, the anti-grease

lters may present a re hazard.

CLEANING STAINLESS STEEL:

Do not use corrosive detergents, abrasive detergents or oven cleaners.

Do not use any product containing chlorine bleach or any product containing chloride.

Do not use steel wool or abrasive scrubbing pads which will scratch and damage surface.

Cleaning Stainless Steel Clean periodically with warm soapy water and clean cotton cloth or

micro fiber cloth. Always rub in the direction of the stainless steel grain. To remove heavier

grease build up use a liquid degreaser detergent. After cleaning use a non-abrasive stainless

steel polish/cleaners, to polish and buff out the stainless luster and grain. Always rub lightly, with

a clean cotton cloth or a micro fiber cloth and buff in the direction of the stainless steel grain.

Any painted surfaces should be cleaned with warm water and detergent only.

- 16 -

LED LIGHT REPLACEMENT

The LED light modules are held in place by

spring clips which must be squeezed in be-

fore the lamp can be pushed down through

the fascia.

Unplug the plastic molex connector.

Plug in the new fixture and snap back into

place.

XOPSPK6602

maintenance continued

XORFSQR

FOR UNITS USED IN RECIRCULATION MODE ONLY:

This refers to hoods which are not ducted outside but rely instead on carbon filter elements

to help purify the air before it is exhausted back into the room.

The carbon element filters gradually lose efficiency and cannot be cleaned or regenerated.

These must be replaced at least 4 times a year, more frequently if needed based on the

amount of use and style of cooking.

CHANGING THE CARBON FILTERS:

Changing the filters is easy.

To Reduce the Risk of Fire and Shock use only

conversion Kit Model XORFSQR(ACK00083) Filters.

The XORFSQR filters are sold in pairs.

To replace the filters, unlatch and remove the

Anti-Grease filters.

This will expose the blower.

Remove the old filter as shown in the figure and

install the new filter simply align and push into

place to lock.

(UL REFERENCE ACK00083)

- 17 -

BUTTON : LIGHT

BUTTON 0: OFF

BUTTON 1: SPEED I

BUTTON 2: SPEED II

BUTTON 3: SPEED III

BUTTON T:

AUTOMATIC STOP TIMER - 15 minutes (*)

• The appliance has the Power Boost speed function: press

BUTTON 3

for two seconds and

it will be activated for 10 minutes after which it will return to the previously set speed. When

the function is active the LED ashes. To interrupt it before the 10 minutes have expired press

BUTTON 3

again.

• By pressing

BUTTON T

for two seconds (with the hood switched o) the “cleanair” func-

tion is activated. This function switches the appliance on for ten minutes every hour at the

rst speed. As soon as this function is activated the motor starts up at the rst speed for ten

minutes. During this time

BUTTON T

and

BUTTON 1

must ash at the same time.

After ten minutes the motor switches o and the LED of

BUTTON T

remains switched on with

a xed light until the motor starts up again at the rst speed after fty minutes and

BUTTON

T

and

BUTTON 1

start to ash again for ten minutes and so on.

By pressing any key for the exclusion of the hood light the hood will return immediately to its

normal functioning (e.g. if

BUTTON 2

is pressed the “cleanair” function is deactivated and

the motor moves to the 2nd speed straight away. By pressing the

BUTTON 0

the function is

deactivated).

(*) The “automatic stop timer” delays stopping of the hood, which will continue functioning for

15 minutes at the operating speed set at the time this

function is activated.

•Activecarbon/greaseltersaturation:

- When button ashes at a frequency of 2 seconds, the grease lters must be cleaned.

- When button ashes at a frequency of 0.5 seconds, the carbon lters must be replaced.

After the clean lter has been replaced, the electronic memory must be reset by pressing

button for approximately 5 seconds, until the light on the button stops ashing.

Your XO range hood is controlled by these

electronic push buttons which illuminate when

activated.

easy to operate

- 18 -

Code Compliance Control

New!

Some local codes limit the maximum exhaust airflow of range hoods to 400 CFM

before a Make Up Air System is required.

The XOM30GC and XOM36GC models are supplied with 600 CFM capacity.

The CCC system allows you to limit the hood from 600 CFM to 395 CFM.

Tosetupfor395CFMOperation-followtheprocedurebelow:

1. After the hood has been powered up initially, disconnect the power supply by shutting

off the circuit breaker.

2. VERY IMPORTANT, after turning power back on to the unit, you must press and hold

both the and “0” buttons simultaneously within 5 seconds of re-powering the unit.

NOTE: If you do not press the buttons within the first 5 seconds after turning power back

on to the hood - the CCC function will not engage and you must repeat from Step 1.

3. The control blinks 3 times

4. The hood is now configured at 395 CFM - the POWER BOOST function is also

disabled.

5. Affix the sticker supplied to indicate the unit has been reconfigured to a maximum

air flow of 395 CFM.

6. Once reconfigured for 395 CFM, the unit cannot be reset to 600 CFM.

make up air conversion

- 19 -

Code Compliance Control

RECIRCULATION KITS

FILTERS

REPLACEMENT LIGHTS

REMOTE CONTROLS

DUCT COVERS

REPLACEMENT SWITCHES

BLOWER MOTORS

FAN WHEELS

ALL OF THESE PARTS AND MORE ARE AVAILABLE, SIMPLY

VISITWWW.XOAPPLIANCE.COMandclickonPARTSSTORE

OR CALL US AT 973-403-8900

access parts & accessories

- 20 -

YEAR

WARRANTY

2

PARTS + LABOR

90 DAY LOVE IT or LEAVE IT. For 90 Days all our products are backed by our unique Love it or Leave it Guarantee.

TWO-YEAR PARTS & LABOR LIMITED WARRANTY. XO warrants to the original purchaser of every new XO ventilation

unit, the cabinet and all parts thereof, to be free from defects in material or workmanship under normal and proper use and

maintenance as specified by XO and upon proper installation and start-up in accordance with the instruction packet supplied

with each XO unit. XO’s obligation under this warranty is limited to a period of two (2) years from the date of original purchase.

WARRANTY CLAIMS. All claims for labor or parts must be made directly through XO. All claims should include: model number

and serial number of cabinet, proof of purchase, and date of installation. In case of warranted compressor, the compressor

model tag must be returned to XO along with the above listed information.

WHAT IS NOT COVERED BY THIS WARRANTY. XO’s sole obligation under this warranty is limited to either repair

or replacement of parts, subject to the additional limitations below. This warranty neither assumes nor authorizes any person

to assume obligations other than those expressly covered by this warranty. Open box, factory seconds, scratch and dent, floor

models and commercial applications are excluded from these warranties.

WARRANTY IS NOT TRANSFERABLE. This warranty is not assignable and applies only in favor of the original purchaser/

user at the original installation location. Any such assignment or transfer shall void the warranties herein made and shall void

all warranties, express or implied, including any warranty or merchantability or fitness for a particular purpose.

IMPROPER USAGE. XO assumes no liability for parts or labor coverage for component failure or other damages resulting from

improper usage or installation or failure to clean and/or maintain product as set forth in the warranty packet provided with the unit.

ALTERATION OR NEGLECT. XO is not responsible for the repair or replacement of any parts that XO determines have been

subjected after the date of manufacture to alteration, neglect, abuse, misuse, accident, damage during transit or installation,

fire, flood, or act of God.

IMPROPER ELECTRICAL CONNECTIONS. XO is not responsible for the repair or replacement of failed or damaged

components resulting from electrical power failure, high or low voltage, use of extension cords, or improper grounding of the unit.

YOUR RIGHTS UNDER STATE LAW. This warranty gives you specific legal rights and you may have other rights that

vary from state to state. Some states do not allow the exclusion or limitation of consequential damages or a limitation on how

long an implied warranty lasts, so the above exclusion or limitation may not apply to you.

OUTSIDE U.S. This warranty does not apply to, and XO is not responsible for, any warranty claims made on products sold

or used outside the 48 continental United States.

To obtain service:

Call 973-403-8900 |email ser[email protected] | or submit a request on our website

www.xoappliance.com

we’ve got your back

La page charge ...

XO M30GC Wall Mount Chimney Range Hood Manuel utilisateur

Ce manuel convient également à

XO M30GC Wall Mount Chimney Range Hood Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents