XO V36KSE XOV Series 36 Inch Wall Mount Ducted Hood Manuel utilisateur

I worked really hard

on this manual - so

please read it...

XOV WALL MOUNT

MODELS XOV36KSE, XOV48KSE

- 3 -

When buying any XO appliance

you can be confident you have chosen a

high quality, innovative and stylish product

from a company that cares about you!

If you require service or have questions,

there are 2 ways to contact our ventilation experts;

Online @ https://xoappliance.com/priority-service-for-your-xo-product/

Or by phone 973-403-8900

CONGRATULATIONS

on purchasing your XO.

Before you proceed, take just a

moment to register your XO at:

www.xoappliance.com/register-your-product/

REGISTRATION HELPS YOU BY -

Ensuring warranty coverage should you need service

Providing ownership verification for insurance purposes

Let’s XO notify you in the event of product changes or recalls.

- 4 -

It’s for your

own good...

Honest.

please read and follow

all safety instructions

where things are

GETTING READY

Safety and Precautions

Planning Ductwork

Install Examples

Dimensions

THE INSTALL

Mounting Height

Installing

Electrical Connections

MAINTENANCE

Filters

Cleaning

Light Replacement

PARTS & WARRANTY 20 - 21

5 - 11

12 - 14

15 - 16

OPERATING

The Controls

17 - 19

- 5 -

safety first

IMPORTANT SAFETY INSTRUCTIONS

FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

IMPORTANT: Save these Instructions for the Local Electrical Inspectors use.

INSTALLER: Please leave these Instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

Take care when using cleaning agents or detergents.

Suitable for use in household cooking area.

WARNING - To reduce the risk of ﬁre or electric shock, do not use this fan with any

Solid-State Speed Control Device.

CAUTION - To reduce risk of ﬁre and to properly exhaust air, be sure to duct air out-

side – Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl

spaces, or garages.

CAUTION - For Residential Kitchen ventilating use only. Do not use to exhaust haz-

ardous or explosive materials and vapors.

CAUTION - To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. oﬀ power unit.

CAUTION - Please read speciﬁcation label on product for further information and

requirements.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the manufacturer. If you have questions,

contact the manufacturer.

B. Before servicing or cleaning unit, switch power oﬀ at service panel and lock the ser-

vice disconnecting means to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a promi-

nent warning device, such as a tag, to the service panel.

WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause smoking and

- 6 -

greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking with high heat.

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on

fan or ﬁlter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface

element.

E. Keep fan, ﬁlters and grease laden surface clean.

F. Use high range setting on range only when necessary. Heat oil slowly on low to me-

dium setting.

G. Don’ t leave range unattended when cooking.

H. Always use cookware and utensils appropriate for the type and amount oﬀ food be-

ing prepared.

WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE

TOP GREASE FIRE, OBSERVE THE FOLLOWING:

A. SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet, or metal tray, then turn oﬀ

the burner. BE CAREFUL TO PREVENT BURNS. If the ﬂames do not go out immediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN – You may be burned.

C. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion

will result.

D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. The ﬁre is small and contained in the area where it started.

3. The ﬁre department is being called.

4. You can ﬁght the ﬁre with your back to an exit.

aBased on “kitchen ﬁresafety tips” published by NFPA.

Proper maintenance of the Range Hood will assure proper performance of the unit.

INSTALLATION INSTRUCTIONS

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be done by qualiﬁed person(s) in accord-

ance with all applicable codes and standards, including ﬁre-rated construction.

B. Suﬃcient air is needed for proper combustion and exhausting of gases through the

ﬂue (chimney) of fuel burning equipment to prevent back drafting. Follow the heat-

ing equipment manufacturer’s guideline and safety standards such as those pub-

lished by the National Fire Protection Association (NFPA), and the American Society

for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local

- 7 -

code authorities.

C. When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

D. Ducted fans must always be vented to the outdoors.

E. This unit must be grounded.

WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

WARNING - UNDER CERTAIN CIRCUMSTANCES DOMESTIC APPLIANCES MAY BE

DANGEROUS.

A. Do not check ﬁlters with hood working.

B. Do not touch the lamps after a prolonged use of the appliance.

C. No food must be cooked ﬂambè underneath the hood.

D. The use of an unprotected ﬂame is dangerous for the ﬁlters and could cause ﬁres.

E. Watch constantly while frying food in order to avoid cooking oil ﬂare ups.

F. Before performing any maintenance operation, disconnect the hood from the

electrical service.

The manufacturers will not accept any responsibility for possible damages, because

of failure to observe the above instructions.

- 8 -

a few simple rules to plan your

ductwork

THIS HOOD IS DESIGNED TO USE AN 8” ROUND DUCT -

IT MAY BE TRANSITIONED TO A 4” X 14” RECTANGULAR DUCT

NEVER REDUCE DUCT SIZE. UNDERSIZED DUCTING SEVERELY RESTRICTS AIR

FLOW AND HARMS PERFORMANCE.

(Example: the area of an 8” Duct is more than 75% larger than a 6” Duct)

KEEP DUCT RUNS AS SHORT AND STRAIGHT AS POSSIBLE.

AVOID USING FLEXIBLE METAL DUCTING IF RUN IS LONGER THAN 6’.

NEVER USE PLASTIC DUCTING.

USE SMOOTH BORE METAL DUCTING.

MINIMIZE THE NUMBER OF FITTINGS (see chart).

WHEN YOU MUST USE FITTINGS, TRY TO SEPARATE THEM WITH SECTIONS OF

4’ OR MORE OF STRAIGHT DUCT.

ALWAYS FOLLOW THE MANUFACTURER’S GUIDELINES FOR THE COOKING

EQUIPMENT YOU ARE VENTING.

IF MAKE UP AIR CONTROL DAMPERS ARE REQUIRED, POSITION THE SENSOR

IN A STRAIGHT RUN OF DUCT IDEALLY WITH 4’ OF STRAIGHT DUCT BETWEEN

EACH SIDE OF THE SENSOR AND A DUCT FITTING. REMEMBER TO INCLUDE

POWER AND CONTROL WIRING FOR THIS IN YOUR PLANS.

ADHERE TO ALL LOCAL BUILDING CODES AND ORDINANCES.

USE THE WORKSHEET THAT FOLLOWS TO HELP CALCULATE THE

TOTAL EQUIVILENT FEET OF YOUR DUCT RUN.

TOTAL EQUIVILENT FEET SHOULD BE LESS THAN 100’.

- 9 -

1

12

7

14

8

2

4

24

33

CAUSING AIR TO CHANGE DIRECTION CAUSES TURBULENCE AND RESTRICTS FLOW IN

A SYSTEM.

IF USING FLEXIBLE METAL DUCT - INCREASE ALL MULTIPLIERS BY 50% (12 BECOMES

18 - ETC.)

THIS EASY TO USE WORKSHEET IS FOR 1000 CFM OR LESS.

UNDER “QTY USED” ENTER HOW OF EACH SECTION YOU WILL BE USING.

IN THE FIRST TWO ROWS - ENTER HOW MANY FEET OF EACH TYPE OF STRAIGHT DUCT

YOU WILL BE USING (I.E. FOR 20 FT ENTER 20, FOR 30FT ENTER 30).

ENTER THE NUMBER OF EACH TYPE OF TURN YOU ARE USING AND THE TYPE OF END CAP.

MULTIPLY ACROSS EACH ROW THE “MULTIPLIER” x “QTY USED” TO GET THE EQUIVALENT

FEET FOR THOSE COMPONENTS.

ADD UP ALL THE VALUES IN THE “EQUIVALENT FEET” COLUMN.

DUCT PIECE DESCRIPTION MULTIPLIER QTY USED EQUIVALENT

FEET

TOTAL EQUIVALENT FEET SHOULD BE LESS THAN 100

estimating total equivalent feet in

a duct

1’ of 8” Round Duct

1’ of 4“ x 14” Rect. Duct

8” 90 Degree Elbow

8” 45 Degree Elbow

4” x 14” 90 Degree

4” x 14” 45 Degree

4” x 14” x 8” Round

4” x 14” x 8” 90 Degree

8” Round Wall Cap w Damper

4” x 14” Wall Cap w Damper

8” Round Roof Cap

- 10 -

WALL EXHAUST ROOF EXHAUST

typical installation examples

- 11 -

11-7/32"

Max 44"

-

Aspiring Version Min. 28-3/4"

10-1/16"

27"

10-7/8"

1-9/16"

20-7/8”

5-6/8”

Ø8"

10-7/8"

1-9/16"

 Front of hood  Side of hood

 Top of hood

dimensions

MODEL A

XOV36KSE 36”

XOV48KSE 48”

 Duct cover removed

- 12 -

27”to32”

RECOMMENDED

MOUNTING HEIGHT

ABOVE GAS AND

ELECTRIC COOKTOPS

highs and lows

All range hoods have a recommended range of installation height over the cooking

surface.

It is important to install the hood at the proper mounting height. Hoods mounted too

low could result in heat damage and fire hazard; while hoods mounted too high will

be hard to reach and will lose its performance and efficiency.

- 13 -

installation

A

C

A

B

A







MOUNT TO THE WALL:

Drill the holes A respecting the distances

indicated (Fig.1). Fix the appliance to

the wall and align it in horizontal posi-

tion to the wall units. When the appli-

ance has been adjusted, deﬁnitely ﬁx

the hood using the screws A (Fig.3). For

the various installations use screws and

screw anchors suited to the type of wall

(e.g. reinforced concrete, plasterboard,

etc.). If the screws and screw anchors are

provided with the product, check that

they are suitable for the type of wall on

which the hood is to be ﬁxed.

INSTALL THE DUCT COVER:

Adjust the width of the support bracket of the upper ﬂue (Fig.2). Then ﬁx it to the ceiling

using the screws A (Fig.3) in such a way that it is in line with your hood and respecting

the distance from the ceiling indicated in Fig.1. Connect the ﬂange C to the air exhaust

hole using a connection pipe (Fig. 3). Insert the upper ﬂue into the lower ﬂue. Fix the

lower ﬂue to the hood using the screws B provided (Fig.3), extract the upper ﬂue up to

the bracket and ﬁx it with the screws B (Fig.2).

IMPORTANT - The range hood must be secured to wall studs or use drywall

anchors capable of supporting 75 lbs.

- 14 -

1. Route the power cord to the junction box.

2. Using listed conduit fittings and connectors,

connect the power supply to the box and each

line to the appropriate wire following this color

convention:

BLACK = HOT LEG

WHITE = NEUTRAL

GREEN/YELLOW = GROUND

Polarity must be observed.

Unit must be properly grounded.

Use a double throw disconnect switch.

3. Replace the box cover

4. Replace the Anti-grease filters.

All wiring must be in compliance with national

electrical code, ANSI/NFPA 70-1999 and all

local codes and regulations.

electrical connection

- 15 -

maintenance

Regular cleaning and maintenance is the key to long life and peak performance of any

equipment.

7KHDQWLJUHDVH¿OWHU is used to trap any grease particles suspended in the air, therefore

LVVXEMHFWWRVDWXUDWLRQWKHWLPHLWWDNHVIRUWKH¿OWHUWREHFRPHVDWXUDWHGGHSHQGVRQWKH

way in which the appliance is used). The JUHDVH¿OWHUVshould be cleaned frequently. Use a

ZDUPGHWHUJHQWVROXWLRQ*UHDVH¿OWHUVDUHDGLVKZDVKHUVDIH

7RSUHYHQWSRWHQWLDO¿UHKD]DUGVWKHDQWL

JUHDVH¿OWHUVVKRXOGEHZDVKHGDPLQLPXP

of every 2 months (it is possible to use the

dishwasher for this task).

$IWHUDIHZZDVKHVWKHFRORXURIWKH¿OWHUV

may change. This does not mean they have to

be replaced. If the replacement and washing

instructions are not followed, the anti-grease

¿OWHUVPD\SUHVHQWD¿UHKD]DUG

CLEANING STAINLESS STEEL:

Do not use corrosive detergents, abrasive detergents or oven cleaners.

Do not use any product containing chlorine bleach or any product containing chloride.

Do not use steel wool or abrasive scrubbing pads which will scratch and damage surface.

Cleaning Stainless Steel Clean periodically with warm soapy water and clean cotton cloth or

micro fiber cloth. Always rub in the direction of the stainless steel grain. To remove heavier

grease build up use a liquid degreaser detergent. After cleaning use a non-abrasive stainless

steel polish/cleaners, to polish and buff out the stainless luster and grain. Always rub lightly, with

a clean cotton cloth or a micro fiber cloth and buff in the direction of the stainless steel grain.

Any painted surfaces should be cleaned with warm water and detergent only.

- 16 -

maintenance continued

LED LIGHT REPLACEMENT

The LED light modules are held in place by

spring clips which must be squeezed in be-

fore the lamp can be pushed down through

the fascia.

Unplug the plastic molex connector.

Plug in the new fixture and snap back into

place.

XOPSPK6602

- 17 -

KEYPAD LAYOUT

DISPLAY LAYOUT

LIGHT BUTTON (1)

- Lights are three level (high, medium, low).

- From off, touch once for high.

- From off, touch twice for medium.

- From off, touch three times for low.

- From off, touch four times to cycle back to off.

- Light level will cycle from high, medium, low, off.

POWER BUTTON (2)

- Power Button will turn power on and off for the entire hood (fan and lights)

- Hood will remember the last speed and light level it was last turned off at (Example: hood

is turned off at when it was last on high speed and high lights; hood will turn back on at high

speed and high lights when Power Button is pressed)

FAN SPEED BUTTON (3)

- From off, press once for low speed (1), twice for medium (2), and three times for high (3).

- Fan should cycle through speeds low (1), medium (2), and high (3) continuously.

easy to operate

- 18 -

DELAY OFF BUTTON (4)

- If fan is off, press once and fan will turn on at low speed and automatically turn off after five

(5) minutes.

- If the fan is already on (example high speed) the fan will change to low speed when the

Delay Off Button is pressed and turn off after five minutes.

- When the Delay Off Function is on, the user can still change the fan speed by pressing the

Fan Speed Button without interrupting the five minute Delay Off Timer.

- Delay Off Function can be turned off by pressing Delay Off Function button or Power Button.

LIGHT INDICATOR (5)

- Light indicator will turn on when lights are turned on at any light level.

DELAY OFF INDICATOR (6)

- Delay Off Indicator will light up when Delay Off Function is activated by pressing the Delay

Off Button.

- Delay Off Indicator will turn off after the Delay Off Function has completed the five minute

cycle or if the user presses the Delay Off Button again or the Power Button.

delay off timer enabled and fan speed changed to 1

CLEAN AIR INDICATOR (7)

- Clean Air Indicator is disabled by default and must be enabled by the user.

7RHQDEOH&OHDQ$LU)XQFWLRQ

With hood off, hold the Power Button down for five seconds. Clean Air Indicator light will

illuminate, and the fan will turn on low speed for 10 minutes. After 10 minutes the fan will turn

off and the 4 hour timer will begin.

Clean Air Indicator will remain on when Clean Air Function is enabled, even if fan is not on.

- When Clean Air Function is enabled, every four hours of non fan usage the fan will automatically

turn on at low speed for 10 minutes. After 10 minutes the fan will turn off and the 4 hour timer

will reset.

- When the Clean Air Function automatically turns the fan on the Clean Air Indicator will blink

and the Low Speed fan indicator will illuminate.

- If the user changes the fan speed while the Clean Air Function is operating, the Clean Air

Indicator will stop blinking but will remain illuminated. When the user manually turns the hood

- 19 -

off the 4 hour timer will reset.

7RGLVDEOH&OHDQ$LU)XQFWLRQ

With hood off, hold Power Button down for five seconds until Clean Air Indicator light turns off.

Note1: Changing the fan speed and interrupting the Clean Air Function while it is operating

does not disable the Clean Air Function. Clean Air Function will only be disabled by holding

the Power Button for 5 seconds.

Note2: Turning lights on/off does not disable the Clean Air Function.

clean air function enabled with low fan speed turned on by clean air function

FAN SPEED INDICATOR (8)

= Low

= Medium

= High

- On speed low, only number 1 indicator will be on.

- On speed medium, 1 and 2 indicator will be on.

- On speed high, 1, 2 and 3 indicators will be on.

- When fan off, no fan speed indicator will be on.

REMOTE CONTROL (OPTIONAL)

Remote control (purchase separately) can be used to operate the hood.

 6\QFKURQL]DWLRQ

The remote control must be synchronized with the hood before using:

To synchronize the remote control with the hood, proceed as follows:

1. Turn the power off and back on at the circuit breaker.

2. When number 5 indicator of the hood lights blinks, press any key of the remote control.

The remote control is now synchronized.

3. If synchronization failed, repeat the procedure.

- 20 -

FILTERS

REPLACEMENT LIGHTS

REMOTE CONTROLS

DUCT COVERS

REPLACEMENT SWITCHES

BLOWER MOTORS

FAN WHEELS

$//2)7+(6(3$576$1'025($5($9$,/$%/(6,03/<

9,6,7:::;2$33/,$1&(&20DQGFOLFNRQ3$5766725(

OR CALL US AT 973-403-8900

access parts & accessories

La page charge ...

XO V36KSE XOV Series 36 Inch Wall Mount Ducted Hood Manuel utilisateur

Ce manuel convient également à

XO V36KSE XOV Series 36 Inch Wall Mount Ducted Hood Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents