Chief MTSAVB Guide d'installation

Catégorie
Supports de sol à panneau plat
Taper
Guide d'installation
INSTALLATION INSTRUCTIONS
Mid-Size Table Mount
MTSAV, -BV, -CV
MTSAV, -BV, -CV Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
display and mount does not exceed 100 lbs (45.4 kg).
DIMENSIONS
Installation Instructions MTSAV, -BV, -CV
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
MTSAV, -BV, -CV Installation Instructions
4
1/4"
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/4"
1/4"
Y (4)
A (1)
E (8)
M4x12mm
F (8)
M4x25mm
G (8)
M5x12mm
H (8)
M5x25mm
I (8)
M5x30mm
J (8)
M5x45mm
K (8)
M6x12mm
L (8)
M6x25mm
M (8)
M6x30mm
N (8)
M6x45mm
O (8)
.750x.344x.500
P (4)
M4
6mmODx4.1mmIDx7mm
S (4)
10-24x1"
T (4)
10-24x2"
U (1)
10-24x1/4"
V (4)
10-24x1/2"
W (4)
#10
X (4)
.375x.194x.032
R (1)
.445x.250x.067
B (1)
Q (4)
C (1)
D (1)
5/32"
Security
I/M
Z (1)
Installation Instructions MTSAV, -BV, -CV
5
ASSEMBLY AND INSTALLATION
WARNING: EXCEEDING WEIGHT CAPACITY CAN
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE
TO EQUIPMENT! It is the installer’s responsibility to make
sure the combined weight of display and mount does not
exceed 100 lbs (45.4 kg).
WARNING: TURNING DISPLAY CAN CAUSE DAMAGE
TO SURROUNDING OBJECTS. Make certain location
provides enough area for the display to rotate ± 270° without
being obstructed, or lock display to a lesser rotation before
rotating for rotating for the first time.
Figure 1
NOTE: The MTS is shipped with the display rotation set at the
maximum of 270°. Display rotation can be adjusted to
0, 10, 20, 30, or 40° and locked if installation location
requires it.
Figure 2
Installation
1. Locate a flat surface (thickness of 1/2" to 1-5/8") on which
to mount the MTS assembly.
2. Mark four mounting hole locations on underside of mounting
surface.
3. Drill four 1/4" dia. (6.35mm) holes through underside of
mounting surface at marks.
4.
Secure MTS post (B) to mounting surface using four 10-24
button head cap screws [(S) - for mounting surfaces up to
3/4" thickness; or (T) - for mounting surfaces from 3/4" to
1-5/8" thickness]. (See Figure 3)
Figure 3
Base
MTS
x 4
x 4
Mounting
Hole
Locations (4)
2
3
Can adjust to tighten
or loosen tension.
or
(T)
(S)
x 4
(W) x 4
Mounting
Surface
4
MTS
MTSAV, -BV, -CV Installation Instructions
6
5. Attach faceplate (A) to post (B) using four 10-24x1/2"
Phillips screws (V), four shoulder washers (Y), and four
nylon washers (X). (See Figure 4)
Figure 4
6. Loosen four Phillips screws and slide faceplate to maximum
height on post.
Attaching Interface Bracket to Display
1. Lay display facedown on a clean and dry flat surface.
2. Attach interface bracket (D) to display using appropriate
screws (E through N). (See Figure 5)
NOTE: If the display has a recessed mounting surface,
spacers (O or P) may be required between the display
and interface bracket (D).
Figure 5
Attaching Display to MTS
1. Make sure the latching flag is in the unlatched position.
(See Figure 6)
2. Align mounting buttons with teardrop holes in the
faceplate (A).
Figure 6
3. Ensure that mounting buttons are firmly located in the
bottom of the teardrop holes.
4. Secure display by placing key (Z) in lock on back of MTS,
turning to place the latching flag in latched and locked
position. (See Figure 6)
6
(X) x 4
(V) x 4
(Y) x 4
5
(D)
2
(E through N)
2
4
1
Latching
Flag
Unlatched
Latching
Flag
Latched
Mounting
Button
(Display
removed
for clarity)
MTS
(Back view)
MTS
(Front view)
Teardrop
Hole
Mounting
Buttons
Display
Lock
Installation Instructions MTSAV, -BV, -CV
7
Setting Rotation Limits
1. Rotation is factory-set at 270
o
but can be changed to 0, 10,
20, 30 or 40
o
to avoid damage to furniture or walls from
display hitting them when rotated. (See Figure 7)
2. Determine amount of rotation allowed in installation and
insert one 10-24x1/4" button head security screw (U) into
the appropriate hole. Tighten to secure rotation amount.
(See Figure 7)
Figure 7
Cable Management
WARNING: ELECTRICAL SHOCK HAZARD! Improper
routing can lead to wires or cables being damaged. Make
certain display power cable is not routed through areas
where it can be pinched or cut.
1. Route display cables and wiring either through front inside
of post and down through mounting surface, or through
cable management hole at base back. (See Figure 8)
Figure 8
2. If wires will be routed through post and down through
mounting surface, place cable management cover (C) over
cable management hole. (See Figure 9)
3. Connect wires and cables to display.
Figure 9
40
o
30
o
20
o
10
o
o
o
(U) x 1
MTS (back view)
Cable routed through
cable management hole
Cable routed through
mounting surface
(C)
MTS
(back)
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
F +31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
MTSAV, -BV, -CV Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-000065 RevC
2010 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
11/10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief MTSAVB Guide d'installation

Catégorie
Supports de sol à panneau plat
Taper
Guide d'installation

dans d''autres langues