Tripp Lite 3-Phase Switched 0U Power Distribution Units Le manuel du propriétaire

1

Owner’s Manual

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

Register your product for quicker service and ultimate peace of mind.

You could also win an ISOBAR6ULTRA surge protector—a $100 value!

www.tripplite.com/warranty

3-Phase Monitored & Switched

0U Power Distribution Units

(Phase, Bank, Outlet Measurements*)

208V MONITORED

MODELS SERIES NO.

PDU3EVN3L2130 AG-00B9

PDU3EVN10L2130 AG-00B9

PDU3EVN3L2120 AG-00B8

PDU3EVN6L2120 AG-00B8

PDU3EVN10L2120 AG-00B8

PDU3EVN6L2130 AG-00B9

208V SWITCHED

MODELS SERIES NO.

PDU3EVSR6G60A AG-0094

PDU3EVSR6H50A AG-0094

200 – 240V

MONITORED

MODELS SERIES NO.

PDU3EVN6G30B AG-00BA

PDU3EVN10G30B AG-00BA

PDU3EVN3G60B AG-00BA

PDU3EVN6G60B AG-00BA

PDU3EVN10G60B AG-00BA

PDU3EVN3H50B AG-00BA

PDU3EVN6H50B AG-00BA

PDU3EVN10H50B AG-00BA

PDU3EVN3L1530B AG-00BA

PDU3EVN6L1530B AG-00BA

PDU3EVN10L1530B AG-00BA

PDU3EVN3L2130B AG-00BA

PDU3EVN6L2130B AG-00BA

PDU3EVN10L2130B AG-00BA

PDU3EVN6G60C AG-00BB

200 – 240V

SWITCHED

MODELS SERIES NO.

PDU3EVSR6H50 AG-00BA

PDU3EVSR10H50 AG-00BA

PDU3EVSR6L1530 AG-00BA

PDU3EVSR10L1530 AG-00BA

PDU3EVSR6L2130 AG-00BA

PDU3EVSR10L2130 AG-00BA

PDU3EVS6H50 AG-00BA

PDU3EVS6L2130 AG-00BA

PDU3EVS6L2120 AG-00BC

PDU3EVSR6L2120 AG-00BC

PDU3EVSR6L1520 AG-00BC

380 – 415V

MONITORED

MODELS SERIES NO.

PDU3XEVN6G20 AG-00BD

380 – 415V

SWITCHED

MODELS SERIES NO.

PDU3XEVSR6G20 AG-00BD

PDU3XEVSR6G30A AG-0096

PDU3XEVSR6G30B AG-0096

PDU3XEVSR6G32A AG-0096

PDU3XEVSR6G32B AG-0080

PDU3XEVSR6G60A AG-0096

PDU3XEVSR6G60B AG-0093

PDU3XEVSR6G63A AG-0096

PDU3XEVSR6G63B AG-0094

PDU3XEVSR6L230B AG-0056

PDU3XEVSR6L2230 AG-0096

PDU3XEVSRHWA AG-0096

PDU3XEVSRHWB AG-0057

Español 17 • Français 33 • Русский 49

17-06-566-93349E.indb 1 9/18/2017 4:23:16 PM

2

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during

the installation, operation, and storage of this product. Failure to heed these

instructions and warnings may affect the product warranty.

• The PDU provides the convenience of multiple outlets, but DOES NOT provide surge or line

noise protection for connected equipment.

• The PDU is designed for indoor use only, in a controlled environment, away from excess

moisture, temperature extremes, conductive contaminants, dust or direct sunlight.

• Keep indoor ambient temperature between 32°F and 122°F (0°C and 50°C).

• The PDU must be installed by a qualiﬁed technician only.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Install in accordance with National Electrical Code standards. Be sure to use the proper

overcurrent protection for the installation, in accordance with the plug/equipment rating.

• Connect the PDU to an outlet that is in accordance with your local building codes and that is

adequately protected against excess currents, short circuits and earth faults.

• The electrical outlets supplying power to the equipment should be installed near the equipment

and easily accessible.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that

eliminate the connection to ground.

• Be sure to provide a local disconnect device on any models that are permanently installed

without a plug that is easily accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• Individual equipment connected to the PDU should not draw more current than the individual

PDU’s outlet’s rating.

• The total load connected to the PDU must not exceed the maximum load rating for the PDU.

• Do not attempt to modify the PDU, input plugs or power cables.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable

parts inside.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to signiﬁcantly

affect its safety or effectiveness is not recommended.

17-06-566-93349E.indb 2 9/18/2017 4:23:16 PM

1-1 1-2

1-4

1-3

1-5

A

B

3

Installation

Mounting the PDU

Note: The illustrations may differ somewhat from your PDU model. Regardless of conﬁguration, the user must

determine the ﬁtness of hardware and procedures before mounting. The PDU and included hardware are designed

for common rack and rack enclosure types and may not be appropriate for all applications. Exact mounting

conﬁgurations may vary. Screws for attaching the mounting brackets to the PDU are included. Use only the screws

supplied by the manufacturer or their exact equivalent.

Note: Mounting buttons come preinstalled to the PDU for toolless mounting.

1-1

To attach the mounting brackets to the

PDU, remove the mounting buttons.

1-2

Attach the mounting brackets to the

PDU with the included screws.

1-3

Attach the PDU to a vertical rail in

your rack or rack enclosure. (Use the

mounting hardware that came with your

rack or rack enclosure to attach the

mounting brackets to the rail.)

1-4

To reinstall the mounting buttons for

toolless mounting, remove the mounting

brackets then install the mounting

buttons onto the PDU. Position the PDU

as desired in the rack enclosure, align

the buttons with the rack mounting

slots, and slide the PDU into position.

Note: Be sure to insert the 2 buttons into either

the upper hole at each end of the PDU or into

the lower hole at each end of the PDU.

1-5

To install the PDU with its outlets facing

the rear of the rack, use the included

PDUMVROTATEBRKT accessory. First,

attach the mounting button

A

to the

V-shaped bracket

B

using the included

screw and washer. Then, use the

button-mount slot to attach the bracket

to the PDU and the mounting button to

attach the PDU to the rack. The bracket

effectively repositions the mounting

brackets allowing for the PDU outlets to

face the rear of the rack.

17-06-566-93349E.indb 3 9/18/2017 4:23:25 PM

4

Installation

Connecting the PDU

2-1

Each model is equipped with 1 of 8 different input plugs.

208V

Monitored Models Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Range

Output

Voltage

Range Breakers

Cord

Length Outlets

PDU3EVN3L2130 L21-30P 24A 208V 208V

3 x Double

Pole, 20A

Branch-Rated

3 ft.

(0.9 m)

36 x C13; 6 x C19;

3 x 5-15/20R

PDU3EVN10L2130 L21-30P 24A 208V 208V

3 x Double

Pole, 20A

Branch-Rated

10 ft.

(3 m)

36 x C13; 6 x C19;

3 x 5-15/20R

PDU3EVN3L2120 L21-20P 16A 208V 208V N/A

3 ft.

(0.9 m)

42 X C13; 6 X C19

PDU3EVN6L2120 L21-20P 16A 208V 208V N/A

6 ft.

(1.8 m)

42 X C13; 6 X C19

PDU3EVN10L2120 L21-20P 16A 208V 208V N/A

10 ft.

(3 m)

42 X C13; 6 X C19

PDU3EVN6L2130 L21-30P 24A 208V 208V

3 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

36 x C13; 6 x C19;

3 x 5-15/20R

208V

Switched Models Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Range

Output

Voltage

Range Breakers

Cord

Length Outlets

PDU3EVSR6G60A

IEC 309 60A Blue

(3P + E); IP44

45A 208V 208V

6 x Low-Proﬁle

with Safety

Lock,

Double Pole,

Magnetic,

Branch-Rated

6 ft.

(1.8 m)

6 x C13; 12 x C19

PDU3EVSR6H50A Hubbell CS8365C 40A 208V 208V

6 x Low-Proﬁle

with Safety

Lock,

Double Pole,

Magnetic,

Branch-Rated

6 ft.

(1.8 m)

6 x C13; 12 x C19

200 – 240V

Monitored Models Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Range

Output

Voltage

Range Breakers

Cord

Length Outlets

PDU3EVN6G30B

IEC 309 30A Blue

(3P + E); IP44

24A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

42 x C13; 6 x C19

PDU3EVN10G30B

IEC 309 30A Blue

(3P + E); IP44

24A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

10 ft.

(3 m)

42 x C13; 6 x C19

L15-20P L15-30P L21-20P L21-30P L22-30P Hubbell CS8365C

IEC 309

30A Blue

(3P + E)

IEC 309

60A Blue

(3P + E)

IEC 309

32A

Red

(3P + N + E)

IEC 309

63A Red

(3P + N + E)

17-06-566-93349E.indb 4 9/18/2017 4:23:25 PM

5

Installation

200 – 240V

Monitored Models Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Range

Output

Voltage

Range Breakers

Cord

Length Outlets

PDU3EVN3G60B

IEC 309 60A Blue

(3P + E); IP44

35A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

3 ft.

(0.9 m)

42 x C13; 6 x C19

PDU3EVN6G60B

IEC 309 60A Blue

(3P + E); IP44

35A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

42 x C13; 6 x C19

PDU3EVN10G60B

IEC 309 60A Blue

(3P + E); IP44

35A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

10 ft.

(3 m)

42 x C13; 6 x C19

PDU3EVN3H50B Hubbell CS8365C 35A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

3 ft.

(0.9 m)

42 x C13; 6 x C19

PDU3EVN6H50B Hubbell CS8365C 35A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

42 x C13; 6 x C19

PDU3EVN10H50B Hubbell CS8365C 35A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

10 ft.

(3 m)

42 x C13; 6 x C19

PDU3EVN3L1530B L15-30P 24A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

3 ft.

(0.9 m)

42 x C13; 6 x C19

PDU3EVN6L1530B L15-30P 24A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

42 x C13; 6 x C19

PDU3EVN10L1530B L15-30P 24A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

10 ft.

(3 m)

42 x C13; 6 x C19

PDU3EVN3L2130B L21-30P 24A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

3 ft.

(0.9 m)

42 x C13; 6 x C19

PDU3EVN6L2130B L21-30P 24A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

42 x C13; 6 x C19

PDU3EVN10L2130B L21-30P 24A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

10 ft.

(3 m)

42 x C13; 6 x C19

PDU3EVN6G60C

IEC 309 60A Blue

(3P + E); IP44

45A

200-

240V

200-

240V

6 x Low-Proﬁle

with Safety

Lock,

Double Pole,

Magnetic,

Branch-Rated

6 ft.

(1.8 m)

36 x C13

200 – 240V

Switched Models Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Range

Output

Voltage

Range Breakers

Cord

Length Outlets

PDU3EVSR6H50 Hubbell CS8365C 35A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

24 x C13; 6 x C19

PDU3EVSR10H50 Hubbell CS8365C 35A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

10 ft.

(3 m)

24 x C13; 6 x C19

PDU3EVSR6L1530 L15-30P 24A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

24 x C13; 6 x C19

17-06-566-93349E.indb 5 9/18/2017 4:23:25 PM

6

Installation

200 – 240V

Switched Models Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Range

Output

Voltage

Range Breakers

Cord

Length Outlets

PDU3EVSR10L1530 L15-30P 24A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

10 ft.

(3 m)

24 x C13; 6 x C19

PDU3EVSR6L2130 L21-30P 24A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

24 x C13; 6 x C19

PDU3EVSR10L2130 L21-30P 24A

200-

240V

200-

240V

3 x Double

Pole, 20A

Branch-Rated

10 ft.

(3 m)

24 x C13; 6 x C19

PDU3EVS6H50 Hubbell CS8365C 35A

200-

240V

200-

240V

3 x Low Proﬁle

with Safety

Lock,

Double Pole,

Magnetic,

Branch-Rated

6 ft.

(1.8 m)

24 x C13; 6 x C19

PDU3EVS6L2130 L21-30P 24A

200-

240V

200-

240V

3 x Low Proﬁle

with Safety

Lock,

Double Pole,

Magnetic,

Branch-Rated

6 ft.

(1.8 m)

24 x C13; 6 x C19

PDU3EVS6L2120 L21-20P 16A

200-

240V

200-

240V

—

6 ft.

(1.8 m)

24 x C13; 6 x C19

PDU3EVSR6L2120 L21-20P 16A

200-

240V

200-

240V

—

6 ft.

(1.8 m)

24 x C13; 6 x C19

PDU3EVSR6L1520 L15-20P 16A

200-

240V

200-

240V

—

6 ft.

(1.8 m)

24 x C13; 6 x C19

380 – 415V

Monitored Models Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Range

Output

Voltage

Range Breakers

Cord

Length Outlets

PDU3XEVN6G20

IEC 309 20A Red

(3P + N + E); IP44

16A

380-

415V

380-

415V

—

6 ft.

(1.8 m)

42 x C13; 6 x C19

380 – 415V

Switched Models Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Range

Output

Voltage

Range Breakers

Cord

Length Outlets

PDU3XEVSR6G20

IEC 309 20A Red

(3P + N + E); IP44

16A

380-

415V

380-

415V

—

6 ft.

(1.8 m)

24 x C13; 6 x C19

PDU3XEVSR6G30A

IEC 309 32A Red

(3P + N + E); IP44

24A

380-

415V

380-

415V

6 x Low-Proﬁle

with Safety

Lock,

Single Pole,

Magnetic,

Branch-Rated

6 ft.

(1.8 m)

12 x C13; 12 x C19

PDU3XEVSR6G30B

IEC 309 32A Red

(3P + N + E); IP44

24A

380-

415V

380-

415V

6 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

24 x C13; 6 x C19

PDU3XEVSR6G32A

IEC 309 32A Red

(3P + N + E); IP44

32A

380-

415V

380-

415V

6 x Low-Proﬁle

with Safety

Lock,

Single Pole,

Magnetic,

Branch-Rated

6 ft.

(1.8 m)

12 x C13; 12 x C19

PDU3XEVSR6G32B

IEC 309 32A Red

(3P + N + E); IP44

32A

380-

415V

380-

415V

6 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

24 x C13; 6 x C19

17-06-566-93349E.indb 6 9/18/2017 4:23:25 PM

7

Installation

380 – 415V

Switched Models Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Range

Output

Voltage

Range Breakers

Cord

Length Outlets

PDU3XEVSR6G60A

IEC 309 63A Red

(3P + N +E); IP44

35A

380-

415V

380-

415V

6 x Low-Proﬁle

with Safety

Lock,

Single Pole,

Magnetic,

Branch-Rated

6 ft.

(1.8 m)

12 x C13; 12 x C19

PDU3XEVSR6G60B

IEC 309 63A Red

(3P + N +E); IP44

35A

380-

415V

380-

415V

6 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

24 x C13; 6 x C19

PDU3XEVSR6G63A

IEC 309 63A Red

(3P + N +E); IP44

40A

380-

415V

380-

415V

6 x Low-Proﬁle

with Safety

Lock,

Single Pole,

Magnetic,

Branch-Rated

6 ft.

(1.8 m)

12 x C13; 12 x C19

PDU3XEVSR6G63B

IEC 309 63A Red

(3P + N +E); IP44

40A

380-

415V

380-

415V

6 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

24 x C13; 6 x C19

PDU3XEVSR6L230B L22-30P 24A

380-

415V

380-

415V

6 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

24 x C13; 6 x C19

PDU3XEVSR6L2230 L22-30P 24A

380-

415V

380-

415V

6 x Low-Proﬁle

with Safety

Lock,

Single Pole,

Magnetic,

Branch-Rated

6 ft.

(1.8 m)

12 x C13; 12 x C19

PDU3XEVSRHWA Hardwire 40A

380-

415V

380-

415V

6 x Low-Proﬁle

with Safety

Lock,

Single Pole,

Magnetic,

Branch-Rated

N/A 12 x C13; 12 x C19

PDU3XEVSRHWB Hardwire 40A

380-

415V

380-

415V

6 x Double

Pole, 20A

Branch-Rated

N/A 24 x C13; 6 x C19

17-06-566-93349E.indb 7 9/18/2017 4:23:25 PM

2-2

2-3

2-4

B

A

8

Installation

2-2

Connect the input plug to your facility’s

compatible AC power source.

2-3

Connect your equipment’s input plugs to

the appropriate outlets on the PDU. The

LED near each outlet illuminates when

the outlet is ready to distribute live

AC power.

Note: It is recommended that you do not

connect a live load to the PDU. If the load you

intend to connect has an ON/OFF switch, please

turn the switch to OFF prior to connection.

2-4

Optional Cord Retention Procedure

Option 1: Use the bridge lances located

near each receptacle to retain power

cords. Tie each equipment power cord

to a bridge lance by looping the cord

and securing it with one of the included

cable ties

A

.

Make sure each cord can

be unplugged from the PDU without

removing the cable tie.

Option 2: Use the included C14 and

C20 plastic sleeves to secure plugs to

receptacles. Attach the sleeve to the

plug, making sure that the pull tabs

B

remain outside the plug and that the ﬁt

is secure. To unplug equipment properly,

use the pull tabs to remove the plug

and sleeve from the receptacle.

Plug type may

vary by model.

Networking the PDU

Your PDU can receive IP address assignments via DHCP server (dynamic) or static (manual)

addressing methods. See the LX Platform User’s Guide for an explanation of these methods. You

can ﬁnd the guide by going to www.tripplite.com/support and typing LX Platform in the search

ﬁeld. If you are uncertain which method to use, contact your network administrator for assistance

before continuing the conﬁguration process.

Note: The MAC address of the PDU (12-digit string in this format: 000667xxxxxx) is printed on a label attached

to the PDU enclosure.

17-06-566-93349E.indb 8 9/18/2017 4:23:27 PM

Network

Input Phase

Load Bank

Outlet

Configuration

Environment

Mobile Access

A

B

C

D

E

F

G

H

9

LCD Touchscreen

A

Main Menu: Use the q on the touchscreen to toggle between the main menu and the

previously selected panel. Available options will vary based on the PDU and peripherals.

B

Network: Displays the IP address, Subnet Mask, Gateway, MAC Address, Device Name,

Model and Serial Number.

C

Input Phase: Displays the amperage and voltage for each phase, as well as the Unbalanced

Load %.

D

Load Bank: Displays the total amperage, wattage and voltage for each load bank as well as

the total power in Watts.

E

Outlet: Displays the amperage and wattage per outlet.

F

Conﬁguration: Displays conﬁgurable settings for the LCD touchscreen.

G

Environment: Displays the data and status of any EnviroSense2 (E2) modules connected

to the PDU. The information shown will vary depending on the E2 model (E2MT, E2MTDI,

E2MTD0, E2MTHDI). Parameters include temperature, RH% (relative humidity), and the

status of input and output dry contacts (open or closed).

H

Mobile Access: Generates a unique QR code to view the PDU’s details on a mobile device.

17-06-566-93349E.indb 9 9/18/2017 4:23:27 PM

Network

Input Phase

Load Bank

Outlet

Configuration

Environment

Mobile Access

10

Using the LCD Touchscreen

Scrolling Through LCD Touchscreen Options

After the system initializes, the Network panel will appear. Use q

on the touchscreen to display the menu. Touch the desired menu

option to select. Available options will vary based on the PDU and

peripherals.

Network

Press Network on the drop down

menu to view the PDU network

details. Press the and to move

between screens. Details displayed

include the IP address (IP), Subnet

Mask (Mask), Gateway (Gate), MAC

Address (MAC), Device Name, Model

and Serial Number. Press q to go

back to the main menu.

Input Phase

Press Input Phase on the drop down menu to view the status of

each phase. The amperage and voltage for L1, L2 and L3 will be

displayed, as well as the Phase Unbalance %.

INPUT PHASE REPORTED LCD REFERENCE

L1 – L2 L1

L2 – L3 L2

L3 – L1 L3

Load Bank

Press Load Bank on the main menu to view the status of each

of the PDU’s load banks. The bank number will be displayed in

addition to total amperage, wattage and voltage per bank, as well

as the total power in Watts. Use and to scroll through the

available banks.

LOAD BANK LCD REFERENCE

Bank 1 1

Bank 2 2

Bank 3 3

17-06-566-93349E.indb 10 9/18/2017 4:23:28 PM

11

Using the LCD Touchscreen

Outlet

Press Outlet on the main menu to view the status of each

PDU outlet. The outlet number will be displayed along with the

amperage and wattage of each individual outlet. Use and to

scroll through all of the outlets.

Conﬁguration

Press Conﬁguration on the drop

down menu to change the PDU

settings. Conﬁgurable settings

include temperature, display

orientation, LCD brightness, LED

settings and a display dimming

option.

Note: Any changes must be saved in

order for the newly conﬁgured settings to

remain.

Screensaver

The screensaver will display after the conﬁgured number of minutes

of inactivity.

Note: If the display is dimmed, any touch to the screen will return the LCD

screen to its previous brightness prior to dimming.

17-06-566-93349E.indb 11 9/18/2017 4:23:29 PM

12

Using the LCD Touchscreen

Environment

Press Environment on the drop down menu to view a panel for

each E2 module connected to the PDU. Use the and to view

other E2 modules.

Note: The available information will vary based on the E2 module.

Mobile Access

A unique QR code is generated each time the Mobile Access

panel is accessed. Make sure the PDU and mobile device are

on the same network. Scan the code with a QR code reader on

your mobile device for read-only access to the PowerAlert Device

Manager.

When accessed through the QR code, PowerAlert Device Manager

is in read-only mode. To access the PDU with full read/write control

from a mobile device on the same network, enter the device’s IP

address in your browser and login to PowerAlert Device Manager as

a user with read/write credentials.

Note: If the Mobile Access panel is blank, a QR code will not be generated

until a valid static or dynamic IP address is assigned to the PDU.

17-06-566-93349E.indb 12 9/18/2017 4:23:29 PM

13

Features

Outlets: During normal operation, the outlets

distribute AC power to connected equipment.

Outlet Status LED: Once the unit is powered on, each outlet individually

ramps up and each Outlet Status LED will illuminate when the associated

outlet is ready to distribute live AC power.

C13 C19

Circuit Breaker (Select Models): There are 3 Load Banks, each

protected by a circuit breaker. If the connected equipment load exceeds

the Maximum Load Rating for those banks of the PDU, the circuit breaker

will trip. Disconnect excess load and reset the breaker.

Note: Each breaker comes equipped with a push-to-reset guard to prevent

accidental breaker tripping. To turn off the breaker, insert a ﬂathead screwdriver into

the reset slot.

Mounting Brackets: Use these brackets as an alternate PDU mounting

method.

Mounting Buttons: Located on the back side of the PDU, the pre-

installed buttons are used for toolless mounting.

Note: Four additional mounting buttons are included for alternate rack styles.

Push-to-Reset Guard

PDUMVROTATEBRKT Mounting Accessory: Use these L-shaped

brackets to mount the PDU with its outlets facing the rear of the rack.

LED Conﬁguration LED Color Outlet Status Description

Standard

1

Off Off Outlet power is absent

Green On Circuit breaker is on – Outlet power is present

Yellow On

Outlet’s current has exceeded 80% of the outlet current

rating – Outlet power is present

Red Off

Outlet’s voltage is below the Low Voltage threshold – Outlet

power is absent

Red Flashing Off Circuit breaker has tripped – Outlet power is absent

Alternate

Off Off Outlet power is absent

Red On Circuit breaker is on – Outlet power is present

Red Flashing On

Outlet’s current has exceeded 80% of the outlet current

rating – Outlet power is present

Green Off Outlet is disabled – Outlet power is absent

Green Flashing Off Circuit breaker has tripped – Outlet power is absent

1

This is the default conﬁguration.

17-06-566-93349E.indb 13 9/18/2017 4:23:31 PM

ACTIVITY

LINK

RESET

CONFIG

A

BC

D

A1

C1 C2

A2

A3

14

Features

A

USB Ports: The two USB-A ports

A1

and

A2

connect

to one of four different Tripp Lite EnviroSense2 (E2)

environmental sensors* for remote temperature or

temperature/humidity monitoring (up to three E2 sensors

can be daisy-chained). The USB-B port

A3

is used for

direct console access from a laptop**.

*USB-A ports are designed for use with E2 modules only. Do not

connect other USB devices to these ports.

**Only 2 of 3 USB ports can be used simultaneously. For example:

2 USB-A (

A1

and

A2

), or 1 USB-B and the lower USB-A port (

A3

and

A1

); the upper USB-A port

A2

cannot connect with the USB-B

port

A3

.

B

RJ45 Conﬁguration Port: This port can be used to

conﬁgure the network card.

D

SNMP Reset Button: The reset button is recessed. Use a paper clip or other suitable object

to press the reset button for 3 seconds to reboot the PDU’s network interface. Rebooting

the network interface will not erase network settings or interrupt AC power. Press and hold

the reset button for 20 seconds to restore the PDU’s network interface to its factory default

settings. Restoring to the factory default will erase all previously saved data—including

network settings—without interrupting AC power.

Ground Screw: Use this to connect any equipment that requires a

chassis ground.

C20 Plug-Lock Inserts (Optional): Use the included C20 plug-lock

inserts to secure plugs to C19 receptacles. Attach the sleeve to the plug

making sure the pull tabs remain outside the plug and that the ﬁt is

secure. To unplug equipment properly, use the pull tabs to remove the

plug and insert from the receptacle.

C14 Plug-Lock Inserts (Optional): Use the included C14 plug-lock

inserts to secure plugs to C13 receptacles. Attach the sleeve to the plug

making sure the pull tabs remain outside the plug and that the ﬁt is

secure. To unplug equipment properly, use the pull tabs to remove the

plug and insert from the receptacle.

C

Ethernet Port: Use this RJ45 jack to connect the PDU to the network with a standard

Ethernet patch cable. The behavior of the Activity LED

C1

and Link LED

C2

is shown in the

table below. This port is not compatible with PoE (Power Over Ethernet) applications.

LED Function LED Color Off On Flashing

Activity Green No Activity — Activity

Link Yellow No Link

Link (Any Speed)

—

Network Interface

17-06-566-93349E.indb 14 9/18/2017 4:23:31 PM

15

Conﬁguration and Operation

Remote Monitoring and Control

The PDU can be monitored and controlled remotely via Web browser, telnet and SNMP-based

Network Management Systems. For more information about conﬁguration and operation of the

PDU via the PowerAlert Device Manger, refer to the LX Platform User’s Guide, which can be found

by going to www.tripplite.com/support and typing LX Platform in the search ﬁeld.

Service

Your Tripp Lite product is covered by the warranty described in this manual. A variety of Extended

Warranty and On-Site Service Programs are also available from Tripp Lite. For more information

on service, visit www.tripplite.com/support. Before returning your product for service, follow these

steps:

1. Review the installation and operation procedures in this manual to ensure that the service

problem does not originate from a misreading of the instructions.

2. If the problem continues, do not contact or return the product to the dealer. Instead, visit

www.tripplite.com/support.

3. If the problem requires service, visit www.tripplite.com/support and click the Product

Returns link. From here you can request a Returned Material Authorization (RMA) number,

which is required for service. This simple on-line form will ask for your unit’s model and

serial numbers, along with other general purchaser information. The RMA number, along

with shipping instructions will be emailed to you. Any damages (direct, indirect, special

or consequential) to the product incurred during shipment to Tripp Lite or an authorized

Tripp Lite service center is not covered under warranty. Products shipped to Tripp Lite or an

authorized Tripp Lite service center must have transportation charges prepaid. Mark the RMA

number on the outside of the package. If the product is within its warranty period, enclose

a copy of your sales receipt. Return the product for service using an insured carrier to the

address given to you when you request the RMA.

17-06-566-93349E.indb 15 9/18/2017 4:23:32 PM

16

Warranty and Product Registration

2- YEAR LIMITED WARRANTY

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in

material and workmanship for a period of 2 years from the date of initial purchase. If the product should prove defective

in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion. Service

under this Warranty can only be obtained by your delivering or shipping the product (with all shipping or delivery charges

prepaid) to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609 USA. Seller will pay return shipping charges. Visit www.

tripplite.com/support before sending any equipment back for repair.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE

OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH

HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL

WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH

ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states

do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives

you speciﬁc legal rights, and you may have other rights which vary from jurisdiction to jurisdiction).

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate

or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes no

representation or warranty as to the suitability or ﬁtness of these devices for any speciﬁc application.

PRODUCT REGISTRATION

Visit www.tripplite.com/warranty today to register your new Tripp Lite product.You’ll be automatically entered into a

drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

FCC Notice, Class A

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense. The user must use shielded cables and

connectors with this equipment. Any changes or modiﬁcations to this equipment not expressly approved by Tripp Lite

could void the user’s authority to operate this equipment.

Regulatory Compliance Identiﬁcation Numbers

For the purpose of regulatory compliance certiﬁcations and identiﬁcation, your Tripp Lite product has been assigned a

unique series number. The series number can be found on the product nameplate label, along with all required approval

markings and information. When requesting compliance information for this product, always refer to the series number.

The series number should not be confused with the marketing name or model number of the product.

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when

customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis

(this varies depending on the country)

• Send the new equipment back for recycling when this ultimately becomes waste

Tripp Lite has a policy of continuous improvement. Speciﬁcations are subject to change without notice.

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

17-06-566-93349E.indb 16 9/18/2017 4:23:32 PM

17

Manual del Propietario

Unidades de Distribución de Energía

Trifásicas Controlables de 0U

(Mediciones de Fase, Banco y Tomacorrientes)

1111 W. 35th Street, Chicago, IL 60609 EE. UU. • www.tripplite.com/support

MODELOS

MONITOREABLES

DE 208V

NO. DE

SERIE

PDU3EVN3L2130 AG-00B9

PDU3EVN10L2130 AG-00B9

PDU3EVN3L2120 AG-00B8

PDU3EVN6L2120 AG-00B8

PDU3EVN10L2120 AG-00B8

PDU3EVN6L2130 AG-00B9

MODELOS

CONTROLABLES

DE 208V

NO. DE

SERIE

PDU3EVSR6G60A AG-0094

PDU3EVSR6H50A AG-0094

MODELOS

MONITOREABLES

DE 200V ~ 240V

NO. DE

SERIE

PDU3EVN6G30B AG-00BA

PDU3EVN10G30B AG-00BA

PDU3EVN3G60B AG-00BA

PDU3EVN6G60B AG-00BA

PDU3EVN10G60B AG-00BA

PDU3EVN3H50B AG-00BA

PDU3EVN6H50B AG-00BA

PDU3EVN10H50B AG-00BA

PDU3EVN3L1530B AG-00BA

PDU3EVN6L1530B AG-00BA

PDU3EVN10L1530B AG-00BA

PDU3EVN3L2130B AG-00BA

PDU3EVN6L2130B AG-00BA

PDU3EVN10L2130B AG-00BA

PDU3EVN6G60C AG-00BB

MODELOS

CONTROLABLES

DE 200V ~ 240V

NO. DE

SERIE

PDU3EVSR6H50 AG-00BA

PDU3EVSR10H50 AG-00BA

PDU3EVSR6L1530 AG-00BA

PDU3EVSR10L1530 AG-00BA

PDU3EVSR6L2130 AG-00BA

PDU3EVSR10L2130 AG-00BA

PDU3EVS6H50 AG-00BA

PDU3EVS6L2130 AG-00BA

PDU3EVS6L2120 AG-00BC

PDU3EVSR6L2120 AG-00BC

PDU3EVSR6L1520 AG-00BC

MODELOS

MONITOREABLES

DE 380V ~ 415V

NO. DE

SERIE

PDU3XEVN6G20 AG-00BD

MODELOS

CONTROLABLES

DE 380V ~ 415V

NO. DE

SERIE

PDU3XEVSR6G20 AG-00BD

PDU3XEVSR6G30A AG-0096

PDU3XEVSR6G30B AG-0096

PDU3XEVSR6G32A AG-0096

PDU3XEVSR6G32B AG-0080

PDU3XEVSR6G60A AG-0096

PDU3XEVSR6G60B AG-0093

PDU3XEVSR6G63A AG-0096

PDU3XEVSR6G63B AG-0094

PDU3XEVSR6L230B AG-0056

PDU3XEVSR6L2230 AG-0096

PDU3XEVSRHWA AG-0096

PDU3XEVSRHWB AG-0057

English 1 • Français 33 • Русский 49

17-06-566-93349E.indb 17 9/18/2017 4:23:32 PM

18

Instrucciones de Seguridad Importantes

CONSERVE ESTAS INSTRUCCIONES

Este manual contiene instrucciones y advertencias que deben seguirse

durante la instalación, operación y almacenamiento de este producto.

La omisión en la observancia de estas instrucciones y advertencias puede

afectar la garantía del producto.

• El PDU proporciona la conveniencia de múltiples tomacorrientes, pero NO proporciona

protección contra sobretensiones o ruido en la línea para los equipos conectados.

• El PDU está diseñada solo para uso en interiores en un entorno controlado lejos de humedad

excesiva, temperaturas extremas, contaminantes conductivos, polvo o luz del sol directa.

• Mantiene la temperatura ambiente interior entre 0 ºC y 50 ºC [32 ºF y 122 ºF]

• El PDU debe ser instalado solamente por un técnico caliﬁcado.

• No intente instalar el PDU en una superﬁcie inestable o no segura.

• Instale conforme a los estándares del Código Eléctrico Nacional. Asegúrese de usar la

protección adecuada contra sobre-corriente para la instalación, de conformidad con la

especiﬁcación de la clavija y del equipo.

• Conecte el PDU a un tomacorrientes que esté de acuerdo a los reglamentos locales de

construcción y que esté correctamente protegido contra corrientes excesivas, cortocircuitos y

fallas de conexión a tierra.

• Los tomacorrientes eléctricos que alimentan al equipo deben instalarse cerca del equipo y ser

fácilmente accesibles.

• No conecte el PDU a un toma corriente que no esté a tierra o cables de extensión o

adaptadores que eliminen la conexión a tierra.

• Asegúrese de proporcionar un dispositivo local de desconexión, que sea fácilmente accesible,

en cualquier modelo que esté instalado permanentemente sin una clavija.

• Nunca intente instalar equipos eléctricos durante una tormenta eléctrica.

• Cada equipo conectado al PDU no debe consumir en forma individual más corriente que la de

la especiﬁcación de cada tomacorrientes individual del PDU.

• La carga total conectada al PDU no debe exceder la capacidad de carga máxima del PDU.

• No intente modiﬁcar el PDU, las clavijas de entrada o los cables de alimentación.

• No perfore ni intente abrir ninguna parte del gabinete del PDU. No tiene partes a las que el

usuario pueda dar servicio.

• No intente usar el PDU si se daña cualquier parte.

• No se recomienda el uso de este equipo en aplicaciones de soporte de vida en donde la falla

de este equipo pueda razonablemente causar la falla del equipo de soporte de vida o afectar

signiﬁcativamente su seguridad o efectividad.

17-06-566-93349E.indb 18 9/18/2017 4:23:32 PM

1-1 1-2

1-4

1-3

1-5

A

B

19

Instalación

Instalación del PDU

Nota: Las ilustraciones pueden diferir un poco de su modelo de PDU. Sin impostar la conﬁguración, antes de la

instalación, el usuario debe determinar la adecuación de los accesorios y procedimientos. El PDU y los accesorios

incluidos están diseñados para tipos comunes de racks y gabinetes y pueden no ser apropiados para todas las

aplicaciones. Las conﬁguraciones de instalación exactas pueden variar. Los tornillos para ﬁjar los soportes de

instalación al PDU están incluidos. Use solamente los tornillos suministrados por el fabricante o su equivalente exacto.

Nota: Para instalación sin herramienta, los botones de instalación vienen pre-instalados en el PDU.

1-1

Para ﬁjar los soportes de instalación

en el PDU, retire los botones de

instalación.

1-2

Con los tornillos incluidos, ﬁje los

soportes de instalación al PDU.

1-3

Fije el PDU a un riel vertical en su rack

o gabinete. (Use los accesorios de

Instalación que vinieron con su rack

o gabinete para ﬁjar los soportes de

instalación al riel).

1-4

Para reinstalar los botones de

instalación para instalación sin

herramientas, retire los soportes de

instalación y coloque los botones de

instalación en el PDU. Coloque el PDU

como desee en el gabinete, alinee los

botones con las ranuras de instalación

del rack y deslice el PDU a su posición.

Nota: Asegúrese de insertar los 2 botones en el

oriﬁcio superior en cada extremo del PDU o en

el oriﬁcio inferior en cada extremo del PDU.

1-5

Para instalar el PDU con sus

tomacorrientes viendo hacia la parte

posterior del rack, use el accesorio

PDUMVROTATEBRKT incluido. Primero,

instale el botón de instalación

A

en

el soporte con perﬁl en V

B

usando

el tornillo y la arandela incluidos.

Entonces, use la ranura de instalación

por botón para ﬁjar el soporte al PDU

y el botón para ﬁjar el PDU al rack. El

soporte reposiciona efectivamente los

soportes de instalación permitiendo que

los tomacorrientes del PDU vean hacia

la parte posterior del rack.

17-06-566-93349E.indb 19 9/18/2017 4:23:34 PM

20

Instalación

Conexión del PDU

2-1

Cada modelo está equipado con 1 de 8 clavijas de alimentación diferentes.

Modelos

Monitoreables de

208V

Clavija de

Entrada

Amperes Máx.

de Entrada

(Limitados

por Cable y

Clavija de

Alimentación)

Rango

del

Voltaje

de

Entrada

Rango

del

Voltaje

de

Salida Breakers

Longitud

de Cable Tomacorrientes

PDU3EVN3L2130 L21-30P 24A 208V 208V

3 x Doble Polo,

20A Especiﬁcados

por Ramal

91 cm

36 x C13; 6 x C19;

3 x 5-15/20R

PDU3EVN10L2130 L21-30P 24A 208V 208V

3 x Doble Polo,

20A Especiﬁcados

por Ramal

3.05 m

36 x C13; 6 x C19;

3 x 5-15/20R

PDU3EVN3L2120 L21-20P 16A 208V 208V N/A 91 cm 42 X C13; 6 X C19

PDU3EVN6L2120 L21-20P 16A 208V 208V N/A 1.83 m 42 X C13; 6 X C19

PDU3EVN10L2120 L21-20P 16A 208V 208V N/A 3 m 42 X C13; 6 X C19

PDU3EVN6L2130 L21-30P 24A 208V 208V

3 x Doble Polo,

20A Especiﬁcados

por Ramal

1.83 m

36 x C13; 6 x C19;

3 x 5-15/20R

Modelos

Controlables de

208V

Clavija de

Entrada

Amperes Máx.

de Entrada

(Limitados

por Cable y

Clavija de

Alimentación)

Rango

del

Voltaje

de

Entrada

Rango

del

Voltaje

de

Salida Breakers

Longitud

de Cable Tomacorrientes

PDU3EVSR6G60A

IEC 309 60A Azul

(3P + T); IP44

45A 208V 208V

6 x Bajo Perﬁl

con Cerradura de

Seguridad, Doble

Polo, Magnético,

Especiﬁcado por

Ramal

1.83 m 6 x C13; 12 x C19

PDU3EVSR6H50A Hubbell CS8365C 40A 208V 208V

6 x Bajo Perﬁl

con Cerradura de

Seguridad, Doble

Polo, Magnético,

Especiﬁcado por

Ramal

1.83 m 6 x C13; 12 x C19

L15-20P L15-30P L21-20P L21-30P L22-30P Hubbell CS8365C

IEC 309

30A Azul

(3P + T)

IEC 309

60A Azul

(3P + T)

IEC 309

32A

Rojo

(3P + N + T)

IEC 309

63A

Rojo

(3P + N + T)

17-06-566-93349E.indb 20 9/18/2017 4:23:34 PM

La page charge ...

Tripp Lite 3-Phase Switched 0U Power Distribution Units Le manuel du propriétaire

Tripp Lite 3-Phase Switched 0U Power Distribution Units Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents