Danby DPA120E1BDB Le manuel du propriétaire

Marque: Danby

Modèle: DPA120E1BDB

Taper: Le manuel du propriétaire

Ce manuel convient également à

DPA100E1BDB

OWNER’S USE AND CARE GUIDE

GUIDE D’UTILISATION ET D'ENTRETIEN

MODEL • MODÈLE

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

2016.12.07

MODEL • MODÈLE

DPA100E1BDB / DPA100E1WDB

DPA120E1BDB / DPA120E1WDB

PORTABLE AIR CONDITIONER

CLIMATISEUR PORTATIF

TO OBTAIN WARRANTY SERVICE YOU MUST PROVIDE A VALID PROOF OF

PURCHASE. PLEASE STAPLE YOUR RECEIPT TO THIS PAGE FOR FUTURE

REFERENCE.

POUR OBTENIR LE SERVICE SUR GARANTIE, VOUS DEVEZ FOURNIR UNE

PREUVE D’ACHAT VALIDE. VEUILLEZ AGRAFER VOTRE REÇU À CETTE PAGE

POUR RÉFÉRENCE FUTURE.

This product is factory equipped with a power supply cord that has a three-pronged ground-

ed plug. It must be plugged into a mating grounding type receptacle in accordance with the

National Electrical Code and applicable local codes and ordinances. If the circuit does not

have a grounding type receptacle, it is the responsibility and obligation of the customer to ex-

change the existing receptacle in accordance with the National Electrical Code and applicable

local codes and ordinances. The third ground prong should not, under any circumstances,

be cut or removed. Never use the cord, the plug or the appliance when they show any sign of

damage. Do not use your appliance with an extension cord unless it has been checked and

tested by a qualiﬁ ed electrician or electrical supplier. Improper connection of the grounding

plug can result in risk of ﬁ re, electric shock and/or injury to persons associated with the ap-

pliance. Check with a qualiﬁ ed service representative if in doubt that the appliance is proper-

ly grounded.

IMPORTANT - GROUNDING METHOD

Ce produit arrive d’origine avec un cordon d’alimentation équipé d’une prise à trois ﬁ ches. Il

doit être branché dans une prise avec une ﬁ che de mise à la terre en conformité avec le Code

national de l’électricité et les codes et règles locaux applicables. Si la prise murale n’a pas de

mise à la terre, il est de la responsabilité et l’obligation du client de changer la prise existante

pour la rendre conforme au Code national de l’électricité et aux codes et règles locaux

applicables. La ﬁ che de mise à la terre ne doit pas, en aucune circonstance, être coupée ou

retirée. Si vous apercevez des signes de dommage, n’utilisez jamais le cordon d’alimentation,

la prise ou l’appareil. N’utilisez jamais l’appareil avec une rallonge sauf si elle a été vériﬁ ée

et testée par un électricien qualiﬁ é ou un fournisseur de matériel électrique. Une ﬁ che de

mise à la terre mal branchée peut entraîner un risque d’incendie, de choc électrique ou de

blessures aux personnes qui utilisent l’appareil. Si vous n’êtes pas certain que l’appareil est

correctement mis à la terre, consultez un préposé du service qualiﬁ é.

IMPORTANT - MÉTHODE POUR LA MISE À LA TERRE

Read and follow all safety rules and operating instructions before

ﬁ rst use of this product.

Veuillez lire attentivement les consignes de sécurité et les instruc-

tions d’utilisation avant l’utilisation initiale de ce produit.

PORTABLE AIR CONDITIONER

Owner’s Use and Care Guide ................................1-14

• Welcome

• Important Safety Information

• Features

• Installation Instructions

• Operation Instructions

• Care and Maintenance

• Troubleshooting

• Warranty

CLIMATISEUR PORTATIF

Guide d’utilisation et d’entretien............................15-28

• Bienvenue

• Consignes de sécurité importantes

• Caractéristiques

• Consignes d’installation

• Consignes d’utilisation

• Soins et entretien

• Dépannage

• Garantie

CONTENTS / TABLE DES MATIÈRES

Model • Modèle

DPA100E1BDB / DPA120E1BDB / DPA100E1WDB / DPA120E1WDB

Welcome

Welcome to the Danby family. We are proud of our quality products, and we believe in dependable service. We suggest

that you read this Owner’s Manual before plugging in your new appliance as it contains important operational information,

safety information, troubleshooting and maintenance tips to ensure the reliability and longevity of your appliance.

Visit www.Danby.com to access self-service tools, FAQs and much more. For additional assistance call 1-800-263-2629.

Note the information below; you will need this information to obtain service under warranty.

To receive service, you must provide the original receipt.

Model Number:

Serial Number:

Date of Purchase:

NEED HELP?

Before you call for service, here are a few things you can do to help

us serve you better:

Read this Owner’s Use and Care Guide:

It contains instructions to help you use and maintain your

appliance properly.

If you received a damaged appliance:

Immediately contact the retailer (or builder) that sold you the

appliance.

Save time and money:

Check the Troubleshooting section at the end of the guide before call-

ing. This section helps you solve common problems that may occur.

If you do need service, you can relax, knowing help is only a phone

call away.

1-800-26-

(1-800-263-2629)

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

To prevent injury to the user or other people and property damage, the follow-

ing instructions must be followed. Incorrect operation resulting from ignoring

these instructions may cause harm or damage.

ALWAYS DO THIS

Your air conditioner should be used in such a way that it is protected from moisture. e.g. con-

densation, splashed water, etc. Do not place or store your air conditioner where it can fall or be

pulled into water or any other liquid. Unplug unit immediately if this occurs.

Always transport your air conditioner in a vertical position and place on a stable, level surface

during use. If the unit is transported laying on its side it should be stood up and left unplugged

for 6 hours.

Turn off the unit when not in use.

Always contact a qualiﬁ ed person to perform repairs. If the power cord is damaged it must be

repaired by a qualiﬁ ed technician.

Keep the unit away from walls, furniture and curtains with a clearance of at least 30 cm all

around.

If the air conditioner is knocked over during use, turn off the unit and unplug it immediately.

Always use the switch on the control panel to turn the unit on or off.

NEVER DO THIS

Do not operate your air conditioner in a wet room such as a bathroom or laundry room.

Do not touch the unit with wet or damp hands.

Do not press the buttons on the control panel with anything other than your ﬁ ngers.

Do not remove any ﬁ xed components. Never use this appliance if it is not working properly, or if

it has been dropped or damaged.

Never use the plug to start and stop the unit.

Do not cover or obstruct the inlet or outlet grilles.

Do not use hazardous chemicals to clean or come into contact with the unit. Do not use the unit

in the presence of inﬂ ammable substances or vapour such as alcohol, insecticides, gasoline,

etc.

Do not allow children to operate the unit unsupervised.

Do not use this product for functions other than those described in this instruction manual.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

To prevent injury to the user or other people and property damage, the following instructions

must be followed. Incorrect operation resulting from ignoring these instructions may cause

harm or damage.

ENERGY SAVING TIPS

OPERATING CONDITIONS

TOOLS FOR WINDOW KIT INSTALLATION

• Use the unit in the recommended room size.

• Locate the unit where furniture cannot obstruct the air ﬂ ow.

• Keep blinds/curtains closed during the sunniest part of the day.

• Keep the ﬁ lters clean.

• Keep doors and windows closed to keep cool air in and warm air out

(cooling mode)

MODE ROOM TEMPERTURE

COOL 18°C (64°F) ~ 35°C (95°F)

DRY 18°C (64°F) ~ 35°C (95°F)

The air conditioner must be operated within the tempera-

ture range indicated below:

Note: Performance may be reduced outside of these operating

temperatures.

1. Screwdriver (medium size, Phillips)

2. Tape measure or ruler

3. Knife or scissors

4. Saw (In the event that the window kit needs to be cut down in size)

See www.danby.com for general instruction guide

Identifying Parts

ELECTRICAL INFORMATION

WARNING

• Be sure the electrical supply is adequate for the model you have chosen. This information can be found on

the serial plate, which is located on the side of the cabinet and behind the grille.

• Be sure the air conditioner is properly grounded. To minimize shock and ﬁ re hazards, proper grounding

is important. The power cord is equipped with a three-prong grounding plug for protection against shock

hazards.

• Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend

to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualiﬁ ed

electrician install the proper receptacle.

• Ensure the receptacle remains accessible after the unit is installed.

• Do not store or use gasoline or other ﬂ ammable vapours and liquids in the vicinity of this or any other

appliance.

• Avoid ﬁ re hazard or electric shock. Do not use an extension cord or an adaptor plug. Do not remove any

prong from the power cord.

Identifying Parts

ACCESSORIES

PARTS PART NAME QUANTITY

• Exhaust hose and adaptor

• Window kit

• Screws

• Foam Seal Type A

• Foam Seal Type B

1 set

• Castor lock 1 set

• Remote control

• Battery

1 set

• Ensure that all the accessories are included in the package and refer to the installation instruc-

tions for their usage.

Note: All the illustrations in this manual are for explanatory purposes only. Your air conditioner may

be slightly different

UNIT STRUCTURE

1. Air outlet grill

2. Handle (both sides)

3. LED Display

4. Castor

5. Air intake grill

6. Control Panel

7. Air intake grill

8. Air outlet

9. Drainage outlet

10. Power cord

Before you begin, thoroughly familiarize yourself with the control panel and remote control and all its

functions. Select the functions you desire based on the associated symbol.

The unit can be controlled by the control panel alone or with the remote control.

Note: This manual does not include Remote control Operation. See the Remote control Instructions

packed with the unit for this information.

Features

ELECTRONIC CONTROL INSTRUCTIONS

POWER button

Turns power on/off.

FAN button

Controls the fan speed. Press to toggle between three fan

speeds, Maximum, Medium and Low

UP and DOWN buttons

Used to adjust (increase / decrease) temperature settings

(1°C/1°F increments) in a range of 18°C(64°F) to 32°C(90°F)

or the TIMER setting in a range of 1~24hrs. The control is

capable of displaying temperature in degrees Fahrenheit or

degrees Celsius. *Converting from °C to °F can be done using

the remote control by pressing the °C/°F button.

MODE select button

Selects the appropriate operating mode. Each time you press

the button, a mode is selected in a sequence that goes from

COOL, DRY, and FAN. The mode indicator light illuminates

depending on the mode settings.

LED DISPLAY

Shows the set temperature in °C or °F (to toggle between °C and °F

press the °C/°F button on the remote control).

Error codes:

LT - Low Temperature. The unit will defrost. The appliance will start again

once defrosting is complete.

PF - Probe failure, call for service.

FT- Tank is full - Connect the drain hose and drain the collected water

away. If error repeats, call for service.

Operating Instructions

OPERATING MODES

COOL mode

• Press the “M” button until the “ ” indicator comes on.

• Press the UP or DOWN arrow buttons to select your desired room temperature. The temperature

can be set within a range of 18°C-32°C / 64°F-90°F.

• Press the “ ” button to choose the fan speed.

Note: The hose should be exhausted in COOL mode.

FAN operation

• Press the “M” button until the “ ” indicator appears.

• Press the “ ” button to choose the fan speed.

Maximum Speed

Medium Speed

Low Speed

DRY mode

• Press the “M” button until the “ ” indicator appears.

• Press the “ ” button to choose the fan speed.

Note: The hose should be exhausted in DRY mode.

Note: To switch the temperature from °C to °F, press the °C/°F button on the remote.

POWER OUTAGE

In the case of a power outage or interruption, the unit will automatically re-start with the last setting

after the power is restored.

Wait 3 minutes before resuming operation

After the unit has stopped, it cannot operate for the ﬁ rst 3 minutes. This is to protect the unit. Opera-

tion of the compressor will automatically start after 3 minutes.

AIR FLOW DIRECTION ADJUSTMENT

Adjust the air ﬂ ow direction automatically (Fig. 4):

• The louver can be adjusted automatically, to change the airﬂ ow direction. (Fig.4)

• When the power is ON, the louver opens fully.

• Press the SWING button on the remote control to initiate the swing feature.

• The swing feature has 3 positions plus auto, P1, P2, P3 and auto swing.

Please do not adjust the louver manually.

Note: Auto swing means the swing will be continuous.

Note: This function is available on the remote control only.

Fig. 4

Installation Instructions

LOCATION

• The air conditioner should be placed on a ﬁ rm foundation to minimize noise and vibration. For safe

and secure positioning, place the unit on a smooth, level ﬂ oor strong enough to support the unit.

• The unit has casters to aid placement, but it should only be rolled on smooth, ﬂ at surfaces. Use

caution when rolling on carpeted surfaces. Use caution and protect ﬂ oors when rolling over wood

ﬂ oors. Do not attempt to roll the unit over objects.

• The unit must be placed within reach of a properly rated grounded socket.

• Never place any obstacles around the air inlet or outlet of the unit.

• Allow at least 30 cm of space away from the wall for efﬁ cient air conditioning.

WINDOW SLIDER KIT INSTALLATION

Your window slider kit has been designed to ﬁ t most standard vertical and horizontal window applica-

tions, however, it may be necessary for you to modify some aspects of the installation procedures for

certain types of windows. The window slider kit can be fastened with a screw (see Fig. 8)

NOTE: If the window opening is less than the minimum length of the window slider kit, cut the end

without the hole in it short enough to ﬁ t in the window opening. Never cut out the hole in window slider

kit (visit www.danby.com for general instruction videos).

Foam seal A

(adhesive type)

Fig.9

Fig.12

Foam seal

Fig.10

Windowsill

Fig.11

Window Kit

Windowsill

Window Kit

28.3 in.

81.5 in.

72 cm - 2.07 m

Installation Instructions

INSTALLATION IN A DOUBLE-HUNG SASH WINDOW

1. Measure the adhesive foam seal to ﬁ t the windowsill. Cut the foam seal to the proper length and

attach it to the windowsill. Fig.9

2. Adjust the length of the window slider kit to ﬁ t the width of the window.

3. Open the window sash and place the window slider kit on the windowsill. Fig.10

4. Cut the foam seal (adhesive type) to the proper length and attach it on the top of the window. Fig.11

5. Close the window sash securely against the window.

6. Cut the foam seal to an appropriate length and seal the open gap between the top window sash and

outer window sash. Shown in Fig.12.

52 cm - 2 m

Foam seal A

(adhesive type)

Fig.13

Fig.14

Window

Panel

Fig.15

Foam

Seal

Fig.16

72 cm -2.07 m

(28.3 - 81.5 in.)

Installation Instructions

INSTALLATION IN A SLIDING SASH WINDOW

1. Measure the adhesive foam seal to ﬁ t the windowsill. Cut the foam seal (adhesive type) to the prop-

er length and attach it to the window frame. Fig. 13

2. Adjust the length of the window slider kit according to the height of the window, shorten the adjust-

able window kit if the height of the window slider is less than the opening. Open the window sash

and place the window slider kit on the windowsill. Fig. 14

3. Cut the foam seal (adhesive type) to the proper length and attach it to the top of the window. Fig. 15

4. Close the sliding sash securely against the window.

5. Cut the foam seal to an appropriate length and seal the open gap between the top window sash

and outer window sash. Fig. 16

52 cm - 2 m

Installation Instructions

EXHAUST HOSE INSTALLATION

The exhaust hose and adaptor must be installed or removed in accordance with the usage mode.

COOL, DRY or AUTO mode Install

FAN Remove

1. Install the window exhaust adaptor onto the exhaust hose as shown in Fig. A. Refer to the previ-

ous pages for window kit installation.

2. Insert the exhaust hose into the rear air outlet opening Fig. A.

• The hose can be compressed or extended moderately according to the installation

requirement, but it is desirable to keep the hose length to a minimum.

IMPORTANT: Do not over bend the hose.

Installation Instructions

WATER DRAINAGE

• During DRY modes, remove the drain plug from the back of the unit, attach the drain hose to the

hole. Place the open end of the hose directly over the drain area in your basement ﬂ oor. Fig. 5

• For small amounts of water, remove the drain plug and place a pan under the drain outlet. Fig. 4

NOTE: Make sure the hose is secure so there are no leaks. Direct the hose toward the drain, making

sure that there are no kinks that will stop the water from ﬂ owing. Place the end of the hose into the drain

and make sure the end of the hose is down to let the water ﬂ ow smoothly. Fig. 6 Never raise it. Fig. 7

NOTE: When operating or draining water, always protect carpeting or ﬂ oors from possible water spillage.

NOTE: Be sure to reinstall the bottom drain plug before using the unit.

NOTE: Drain hose not included.

Drain outlet

Drain plug

Drain pan

Drain plug

Drain outlet

Drain hose

Care and Maintenance

IMPORTANT

1. Be sure to unplug the unit before cleaning or servicing.

2. Do not use gasoline, paint thinner or other chemicals to clean the unit.

3. Do not wash the unit directly under a tap or using a hose. It may cause electrical damage.

4. If the power cord is damaged, contact the service depot immediately.

UNIT ENCLOSURE

Use a lint-free cloth soaked with neutral detergent to clean the unit enclosure, be sure to wring the

cloth of excess water. Finish by wiping with a clean dry cloth.

LONG-TERM STORAGE

• Remove the rubber plug at the back of the unit and attach a hose to the drain outlet. Place the

open end of the hose directly over the drain area in your basement ﬂ oor.

• Remove the plug from the bottom drain outlet, this means that all the water in the bottom drain

tray will drain out.

• Keep the appliance running on FAN mode for half a day in a warm room to dry the appliance in-

side and prevent mold formation.

• Turn off the appliance and unplug it, wrap the cord and bundle it with tape.

• Remove the batteries from the remote control.

• Clean the air ﬁ lter and reinstall it.

AIR FILTER

Clean the air ﬁ lter at least once every two weeks. Accumulation of dust will hinder fan operation.

REMOVAL

This unit has three ﬁ lters. Pull the upper grill out in the direction of the arrow (Fig. 8) and slide the

ﬁ lter out. Remove the lower ﬁ lters by removing the grill and then sliding it out the side in the direction

of the arrow (Fig. 9-11).

CLEANING

1. Wash the air ﬁ lter by submerging it gently in warm water (below 40°C / 104° F) with a neutral de-

tergent.

2. Rinse the ﬁ lter and let it dry.

REINSTALL

Install the upper air ﬁ lter after cleaning, and install the lower ﬁ lters after. *Filters must be dry before

installing*

Troubleshooting

Tel: 1-800-26- (1-800-263-2629)

PROBLEM POSSIBLE CAUSE SOLUTION

Unit does not start when

pressing on/off button

• FT appears in the display

window

• Room temperature is lower

than the set temperature.

(Cooling mode)

• Drain the water in the bottom

tray

• Reset the temperature

Not cool enough • The windows or doors in the

room are not closed

• There are heat sources

inside the room

• Exhaust air hose is not con-

nected or blocked

• Temperature setting is too

high

• Air ﬁ lter is blocked by dust

• Make sure all the windows and

doors are closed

• Remove the heat sources if

possible

• Connect the hose and make

sure it can function properly

• Decrease the set temperature

• Clean the air ﬁ lter

Noisy or vibration • The ground is not level or

not ﬂ at enough

• Place the unit on a ﬂ at, level

ground if possible

Gurgling sound • The sound comes from the

ﬂ owing of the refrigerant

inside the air conditioner

• It is normal

DISPOSAL

Check for local regulatory compliance regarding the approved and safe disposal of this appliance.

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating

conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter

“Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

First Year

During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s

option, at no charge to the ORIGINAL purchaser.

To obtain

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance

Service

requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at

their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service

must be performed by a qualied service technician.

If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all

obligations of Danby under this warranty shall be void.

Boundaries of

If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be

In Home Service

delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for

warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he

responsibility of the purchaser.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due

to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its

authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees

under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages

to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of

the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions

(extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).

Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our

AUTHORIZED SERVICE DEPOT.

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

04/09

1-800-263-2629

Warranty Service

In-home

If the appliance is installed in a location that is 100 kilometres (62 miles) or more from the nearest

service centre your unit must be delivered to the nearest authorized Danby Service Depot, as service

must only be performed by a technician qualified and certified for warranty service by Danby. Transpor-

tation charges to and from the service location are not protected by this warranty and are the responsi-

bility of the purchaser.

During the first twelve (12) months, any functional parts of this product found to be defective, will be

repaired or replaced, at warrantor’s option, at no charge to the ORIGINAL purchaser.

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized

Service Depot. Any appliance requiring service outside the limited boundaries of “In Home Service” ,it

will be the consumer’s responsibility to transport the appliance (at their own expense) to the original

retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Service” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby

service depot, where service must be performed by a qualified service technician. If service is performed

on the units by anyone other than an authorized service depot, or the unit is used for commercial

application, all obligations of Danby under this warranty shall be void.

First year

To obtain

service

Boundaries of

in-home service

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is

used under the normal operating conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or

Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other

contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or

implied, made or intended by Danby or its authorized distributors and all other warranties, conditions, representations or

guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation

or statute is hereby expressly excluded. Save as herein provided, Danby shall not be responsible for any damages to persons

or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit

and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for

damages to persons or property caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating

conditions (extremely high or low room temperature).

5) Use for commercial or industrial purposes (i.e., If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc.

7) Service calls resulting in customer education.

8) Improper Installation (i.e., building-in of a free standing appliance or using an appliance outdoors that is not approved for

outdoor application). Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event

warranty service is required, present this document to our AUTHORIZED SERVICE DEPOT.

Warranty Service

In-home

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

1-800-263-2629

07/14

Bienvenue

Bienvenue dans la famille Danby. Nous sommes fiers de la qualité de nos produits et nous croyons en le service fiable.

Nous vous suggérons de lire ce manuel d’utilisation avant de brancher vontre nouvel appareil car il contient des informations

importantes sur l’utilisation, la sécurité, le dépannage at la maintenance, afin d’assurer la fiabilité at la longévité de votre

appareil. Visitez www.Danby.com pour accéder aux outils d’autoservice, aux FAQ et bien plus encore. Pour obtenir de l’aide

supplémentaire, composez le 1-800-263-2629.

Veuillez noter les informations ci-dessous; ces renseignements seront nécessaires si votre appareil a besoin

d’entretien ou pour les demandes de renseignements généraux. Pour bénéficier d’une opération de mainte-

nance ou de dépannage, le reçu original sera exigé.

Numéro de modèle :

Numéro de serie :

Date d’achat :

BESOIN D’ASSISTANCE ?

Veuillez trouver quelques conseils avant de faire appel à nos

services, cela nous aidera à mieux vous servir :

Lisez ce guide :

Il comprend des instructions pour l’utilisation et l’entretien

adapté de votre appareil.

Si votre nouvel appareil est endommagé :

Contactez immédiatement le revendeur (ou le fabricant).

Gagnez du temps et de l’argent :

Avant de faire appel à nos services, consultez à nouveau

la section « Dépannage ». Cette section vous aidera à

résoudre des problèmes courants.

Si une réparation est nécessaire, ne vous inquiétez pas, la

solution est au bout du fil.

1-800-26-

(1-800-263-2629)

Consignes de sécurité importantes

LISEZ TOUTE L’INFORMATION DE SÉCURITÉ AVANT UTILISATION

Pour votre sécurité : Lisez ces instructions attentivement avant d’utiliser l’ap-

pareil et conservez-les aﬁ n de pouvoir vous y référer ultérieurement.

SUIVEZ TOUJOURS CES CONSIGNES

L’appareil doit être utilisé dans un endroit à l’abri de l’humidité, comme la condensation, les

éclaboussures d’eau, etc. Ne le placez pas dans un endroit où il pourrait tomber dans l’eau ou

d’autres liquides.

Transportez toujours l’appareil en position verticale. Utilisez-le sur une surface stable et de

niveau. Si l’appareil est transporté, couché, il faudra le remettre en position verticale et le garder

débranché pendant 6 heures.

Éteignez le produit s’il n’est pas utilisé.

Faites faire toute réparation par un technicien qualiﬁ é. Si le cordon d’alimentation est endom-

magé, il doit être réparé par un technicien qualiﬁ é.

Laissez un espace libre d’au moins 30 cm (1 pied) autour de l’appareil (p.ex., des murs, des

meubles et des rideaux) pour permettre un bonne circulation de l’air.

Si le climatiseur tombe alors qu’il est en marche, éteindre l’appareil et le débrancher immédiate-

ment.

Utilisez toujours l’interrupteur du panneau de commande pour éteindre l’appareil ou le mettre en

marche.

MISES EN GARDE

Ne faites pas fonctionner le climatiseur dans une pièce humide, comme une salle de bain ou de

lavage

Ne touchez pas à l’appareil les mains mouillées ou humides

N’appuyez sur les boutons du panneau de commande qu’avec les doigts

Ne retirez pas les couvercles ﬁ xes. N’utilisez jamais cet appareil s’il fonctionne mal ou s’il a été

échappé ou endommagé

Ne couvrez pas les grilles d’entrée ou de sortie, et ne les obstruez pas

Ne nettoyez pas cet appareil à l’aide de produits, chimiques dangereux. Ne les mettez pas en

contact avec l’appareil

N’utilisez pas cet appareil en présence de substances inﬂ ammables comme l’alcool, les insecti-

cides, le gaz, l’essence, etc.

Ne laissez pas les enfants utiliser cet appareil sans surveillance

N’utilisez pas ce produit pour des fonctions autres que celles décrites dans ce guide

Consignes de sécurité importantes

LISEZ TOUTE L’INFORMATION DE SÉCURITÉ AVANT UTILISATION

Pour votre sécurité: Lisez ces instructions attentivement avant d’utiliser l’appareil et

conservez-les aﬁ n de pouvoir vous y référer ultérieurement.

CONDITIONS DE FONCTIONNEMENT

ÉCONOMISEZ L’ÉNERGIE

• Utilisez l’appareil dans des pièces des dimensions recommandées.

• Placez l’appareil dans un endroit où les meubles n’obstruent pas la circulation d’air.

• Fermez les stores et rideaux pendant les moments les plus ensoleillés de la journée.

• Gardez le ﬁ ltre de l’appareil propre.

• Fermez les portes et les fenêtres pour garder l’air froid à l’intérieur et l’air chaud à l’extérieur.

MODE TEMPÉRATURE DE LA PIÈCE

REFROIDISSEMENT 18°C (62 ° F) ~ 35°C (95°F)

DÉSHUMIDIFICATION 18 °C (62°F) ~ 35°C (95°F)

Le climatiseur doit être utilisé à l’intérieur de la plage de température qui ﬁ gure ci-dessous :

Remarque : Une température hors de ces plages peut réduire le rendement.

OUTILS POUR L’INSTALLATION DE LA TROUSSE POUR FENÊTRE

1. Tournevis (moyen, à lame plate)

2. Ruban à mesure ou règle

3. Couteau ou ciseaux

4. Scie (si la trousse pour fenêtre doit être coupée)

Voir www.danby.com pour obtenir un guide d’instrucions pour l’installation générale.

Identiﬁ cation des pièces

RENSEIGNEMENTS RELATIFS À L’ÉLECTRICITÉ

AVERTISSEMENT

• Assurez-vous que l’alimentation en électricité correspond au modèle que vous avez choisi.

Ces informations sont disponibles sur la plaque signalétique, qui se trouve sur côté du

châssis et derrière la grille.

• Assurez-vous que le climatiseur est correctement mis à la terre. Une mis à la terre correcte

est importante pour minimiser les risques de choc et de feu. Le cordon d’alimentation est

muni d’une prise de mise à la terre à trois broches pour vous protéger contre les risques

de choc.

• Votre climatiseur doit être branché sur une prise murale correctement mise à la terre.

Si la prise murale que vous prévoyez utiliser n’est pas mise à la terre correctement ou

protégée par un fusible à fusion lente ou un disjoncteur, demandez à un électricien qualiﬁ é

d’installer la bonne prise.

• Assurez-vous que la prise sera accessible après l’installation de l’appareil.

• Ne conservez et n’utilisez ni essence, ni vapeurs ou substances liquides inﬂ ammables à

proximité de cet appareil ou de tout autre appareil.

• Évitez les risques de feu ou de choc électrique. N’utilisez pas de rallonge ou d’adaptateur.

N’enlevez pas de broche sur le cordon d’alimentation.

La page charge ...

Danby DPA120E1BDB Le manuel du propriétaire

Marque: Danby

Modèle: DPA120E1BDB

Taper: Le manuel du propriétaire

Ce manuel convient également à

DPA100E1BDB

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DPA120E1BDB Owner's manual

Documents connexes

Autres documents

Argo NANTE Manuel utilisateur