Danby DPA080C2SDB Le manuel du propriétaire

Marque: Danby

Modèle: DPA080C2SDB

Catégorie: Climatiseurs mobiles

Taper: Le manuel du propriétaire

OWNER’S USE AND CARE GUIDE

GUIDE D’UTILISATION ET D'ENTRETIEN

MODEL • MODÈLE

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

DPA080C2SDB

PORTABLE AIR CONDITIONER

CLIMATISEUR PORTATIF

2015.01.05

DO NOT RETURN THIS UNIT TO THE RETAILER

WITHOUT FURTHER INSTRUCTIONS

Dear valued customer, we hope your Danby product purchase fulfills all

your requirements. Your satisfaction is our priority!

Please contact us at our toll free consumer service number for any inquiries

you may have about your new unit.

NE PAS RETOURNER CET APPAREIL CHEZ LE

DÉTAILLANT SANS CONSIGNES SUPPLÉMENTAIRES

Cher(ère) client(e) important(e), nous espérons que votre produit Danby

répond à tous vos besoins. Votre satisfaction est notre priorité!

Veuillez nous contacter au numéro gratuit de service après-vente, si

vous avez des questions quelconques à propos de votre nouvel appareil.

NO DEVUELVA ESTA UNIDAD A LA TIENDA SIN

INSTRUCCIONES ADICIONALES

Estimado cliente, esperamos que el producto Danby que ha comprado

satisfaga completamente sus necesidades. Su satisfacción

es nuestra prioridad!

Por favor, contáctenos gratuitamente a nuestro número de Servicio al

Cliente para cualquier pregunta que tenga sobre su nuevo electrodoméstico.

1-800-263-2629

(1-800-26-DANBY)

Danby 28.08.2014

TO OBTAIN WARRANTY SERVICE YOU MUST PROVIDE A VALID PROOF OF

PURCHASE. PLEASE STAPLE YOUR RECEIPT TO THIS PAGE FOR FUTURE

REFERENCE.

POUR OBTENIR LE SERVICE SUR GARANTIE, VOUS DEVEZ FOURNIR UNE

PREUVE D’ACHAT VALIDE. VEUILLEZ AGRAFER VOTRE REÇU À CETTE PAGE

POUR RÉFÉRENCE FUTURE.

This product is factory equipped with a power supply cord that has a three-pronged grounded plug. It must

be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and

applicable local codes and ordinances. If the circuit does not have a grounding type receptacle, it is the

responsibility and obligation of the customer to exchange the existing receptacle in accordance with the

National Electrical Code and applicable local codes and ordinances. The third ground prong should not,

under any circumstances, be cut or removed. Never use the cord, the plug or the appliance when they show

any sign of damage. Do not use your appliance with an extension cord unless it has been checked and test-

ed by a qualiﬁ ed electrician or electrical supplier.

IMPORTANT - GROUNDING METHOD

Ce produit arrive d’origine avec un cordon d’alimentation équipé d’une prise à trois ﬁ ches. Il doit être

branché dans une prise avec une ﬁ che de mise à la terre en conformité avec le Code national de l’électricité

et les codes et règles locaux applicables. Si la prise murale n’a pas de mise à la terre, il est de la

responsabilité et l’obligation du client de changer la prise existante pour la rendre conforme au Code

national de l’électricité et aux codes et règles locaux applicables. La ﬁ che de mise à la terre ne doit pas, en

aucune circonstance, être coupée ou retirée. Si vous apercevez des signes de dommage, n’utilisez jamais le

cordon d’alimentation, la prise ou l’appareil. N’utilisez jamais l’appareil avec une rallonge sauf si elle a été

vériﬁ ée et testée par un électricien qualiﬁ é ou un fournisseur de matériel électrique.

IMPORTANT - MÉTHODE POUR LA MISE À LA TERRE

PORTABLE AIR CONDITIONER

Owner’s Use and Care Guide .................................

• Welcome

• Important Safety Information

• Features

• Installation Instructions

• Operation Instructions

• Care and Maintenance

• Troubleshooting

• Warranty

CLIMATISEUR PORTATIF

Guide d’utilisation et d’entretien................................

• Bienvenue

• Consignes de sécurité importantes

• Caractéristiques

• Consignes d’installation

• Consignes d’utilisation

• Soins et entretien

• Dépannage

• Garantie

CONTENTS

CAUTION:

Read and follow all safety rules and operating

instructions before ﬁ rst use of this product.

AVERTISSEMENT :

Veuillez lire attentivement les consignes de

sécurité et les instructions d’utilisation avant

l’utilisation initiale de ce produit.

TABLE DES MATIÈRES

Model • Modèle

WARNING

Improper connection of the grounding plug can

result in risk of ﬁ re, electric shock and/or injury to

persons associated with the appliance. Check with

a qualiﬁ ed service representative if in doubt that

the appliance is properly grounded.

AVERTISSEMENT

Une ﬁ che de mise à la terre mal branchée peut

entraîner un risque d’incendie, de choc électrique

ou de blessures aux personnes qui utilisent

l’appareil. Si vous n’êtes pas certain que l’appareil

est correctement mis à la terre, consultez un

préposé du service qualiﬁ é.

1-17

18-34

DPA080C2SDB

Welcome

Welcome to the Danby family. We are proud of our quality products, and we believe in dependable service, like you will

find in this Owner’s Use and Care Guide, and like you will receive from our friendly customer service department. Best

of all, you will experience these values each and every time you use your Danby appliance. That is important, because

your new appliance will be a part of your family for a long time.

Note the information below; you will need this information to obtain service under warranty.

To receive service, you must provide the original receipt.

Serial

Number:

Date of Purchase:

NEED HELP?

Before you call for service, here are a few things you can do to help

us serve you better:

Read this Owner’s Use and Care Guide:

It contains instructions to help you use and maintain your

appliance properly.

If you received a damaged appliance:

Immediately contact the retailer (or builder) that sold you the

appliance.

Save time and money:

Check the Troubleshooting section at the end of the guide before call-

ing. This section helps you solve common problems that may occur.

If you do need service, you can relax, knowing help is only a phone

call away.

1-800-26-

(1-800-263-2629)

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

To prevent injury to the user or other people and property damage, the following instructions must be

followed. Incorrect operation resulting from ignoring these instructions may cause harm or damage.

SAFETY

PRECAUTIONS

ALWAYS DO THIS

Your air conditioner should be used in such a way that it is protected from

moisture. e.g. condensation, splashed water, etc. Do not place or store

your air conditioner where it can fall or be pulled into water or any other

liquid. Unplug unit immediately if this occurs.

Always transport your air conditioner in a vertical position and place on a

stable, level surface during use. If the unit is transported laying on its side it

should be stood up and left unplugged for 4 hours.

Turn off the unit when not in use.

Always contact a qualiﬁ ed person to perform repairs. If the power cord is

damaged it must be repaired by a qualiﬁ ed technician.

Keep the unit away from walls, furniture and curtains with a clearance of at

least 30 cm all around.

If the air conditioner is knocked over during use, turn off the unit and

unplug it immediately.

Always use the switch on the control panel to turn the unit on or off.

Portable air conditioners exhaust large amounts of room air. Always ensure

an adequate supply of make-up air to operate efﬁ ciently.

NEVER DO THIS

Do not operate your air conditioner in a wet room such as a bathroom or

laundry room.

Do not touch the unit with wet or damp hands.

Do not press the buttons on the control panel with anything other than your

ﬁ ngers.

Do not remove any ﬁ xed components. Never use this appliance if it is not

working properly, or if it has been dropped or damaged.

Never use the plug to start and stop the unit.

Do not cover or obstruct the inlet or outlet grilles.

Do not use hazardous chemicals to clean or come into contact with the unit.

Do not use the unit in the presence of inﬂ ammable substances or vapour

such as alcohol, insecticides, gasoline, etc.

Do not allow children to operate the unit unsupervised.

Do not use this product for functions other than those described in this

instruction manual.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

To prevent injury to the user or other people and property damage, the following instructions must be

followed. Incorrect operation resulting from ignoring these instructions may cause harm or damage.

ENERGY SAVING

TIPS

OPERATING

CONDITIONS

TOOLS FOR

WINDOW KIT

INSTALLATION

• Use the unit in the recommended room size.

• Locate the unit where furniture cannot obstruct the air ﬂ ow.

• Keep blinds/curtains closed during the sunniest part of the day.

• Keep the ﬁ lters clean.

• Keep doors and windows closed to keep cool air in and warm air out

(cooling mode)

MODE ROOM TEMPERTURE

Air conditioning 16°C ~ 35°C (61°F ~ 95°F)

The air conditioner must be operated within the temperature range

indicated below:

Note: Performance may be reduced outside of these operating tempera-

tures.

1. Screwdriver (medium size, Phillips)

2. Tape measure or ruler

3. Knife or scissors

4. Saw (In the event that the window kit needs to be cut down in size

because the window is too narrow for direct installation).

See www.danby.com for general instruction guide

The power cord supplied with this air conditioner contains a device that senses damage to the power cord. To test if your

power cord is working properly, you must do the following:

1. Connect the power supply cord to an electrical outlet.

2. The power supply cord has two buttons located on the head of the plug. One button is marked “TEST”, and the other

is marked “RESET”. Press the “TEST” button; you will hear a click as the “RESET” button pops out.

3. Press the “RESET” button; you will hear a click as the button engages.

4. The power supply cord is now energized and supplying electricity to the air conditioner (on some products this is also

indicated by a light on the plug head).

NOTE: The power cord supplied with this air conditioner contains a current leakage detection device designed to reduce

the risk of ﬁ re. In the event the power supply cord is damaged, it cannot be repaired and must be replaced with a new

cord from the product manufacturer.

• Under no circumstances should this device be used to turn the unit on or off.

• The “RESET” button must always be pushed in (engaged) for correct operation.

• The power supply cord must be replaced if it fails to reset when the “TEST” button is pushed in.

NOTE: Some plugs have buttons on the top.

POWER SUPPLY CORD

Plug in and press

RESET

TEST

RESET

Identifying Parts

WARNING

• Do not store or use gasoline or other ﬂ ammable vapours and liquids in the vicinity of this or any other

appliance.

• Avoid ﬁ re hazard or electric shock. Do not use an extension cord or an adaptor plug. Do not remove any

prong from the power cord.

ELECTRICAL INFORMATION

WARNING

• Be sure the electrical supply is adequate for the model you have chosen. This information can be found

on the serial plate, which is located on the side of the cabinet and behind the grille.

• Be sure the air conditioner is properly grounded. To minimize shock and ﬁ re hazards, proper grounding

is important. The power cord is equipped with a three-prong grounding plug for protection against

shock hazards.

• Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you

intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a

qualiﬁ ed electrician install the proper receptacle.

• Ensure the receptacle remains accessible after the unit is installed.

TABLE 2

Receptacle and Fuse Types

Rated Volts 125

Amps 15

Wall Outlet

Fuse Size 15

Time Delay Fuse Plug Type

(or Circuit Breaker)

TABLE 1

Suggested Individual Branch Circuit

Nameplate Amps

5.9

*AWG Wire Size

AWG- American Wire Gauge

*Based on copper wire at 105°C temperature rating

1. All wiring must comply with local and national electrical codes and must be installed by a qualiﬁ ed electrician. If you

have any questions regarding the following instructions, contact a qualiﬁ ed electrician.

2. Check available power supply and resolve any wiring problems BEFORE installing and operating this unit.

3. This 115V air conditioner uses 5.9 or less nameplate amps and may be used in any properly wired, general-purpose

household receptacle. See Table 1 for the speciﬁ cations for the individual branch circuit.

4. For your safety and protection, this unit is grounded through the power cord plug when plugged into a matching wall

outlet. If you are not sure whether your wall outlet is properly grounded, please consult a qualiﬁ ed electrician.

5. The wall outlet must match the 3-prong plug on the service cord supplied with the unit. DO NOT use plug adapters.

See Table 2 for receptacle and fuse information.

• Ensure that all the accessories are included in the

package and refer to the installation instructions for

their usage.

Note: All the illustrations in this manual are for ex-

planatory purposes only. Your air conditioner may be

slightly different.

Identifying Parts

FEATURES

ACCESSORIES

ELECTRIC SHOCK HAZARD: To avoid the possibility of

personal injury, disconnect power to the unit before installing or

servicing.

Installation Accessories:

• Flexible exhaust hose

• Exhaust nozzle connector (3 pcs) (Connector A, B and C)

• Window door slider kit (3 pcs)

• Screws (5 pcs)

• Pipe Clip

• Pipe Hoop (2)

• Drainage Pipe

• Rubber Plug

• Adhesive foam (2)

• Non-adhesive foam (4)

NOTE: The exhaust / window kit must be installed at all times

when the unit is operating under AIR CONDITIONING mode.

There should be at least 11.8” (30cm) clearance between the

unit and any other objects or building structures, and the unit

should be installed on a level ﬂ oor. The unit does not have

to be vented outside during dehumidifying or fan only mode

operation. When the unit is in dehumidifying mode, the warm

air exhaust must be vented inside the room.

1. Control Panel

2. Air outlet

3. Caster

4. Remote Control Holder

5. Power Cord

6. Air Filter

7. Upper Air Inlet Grill

8. Lower Air Inlet Grill

Exhaust

Connector A

Exhaust

Connector B

Exhaust

Connector C

Window Slider

Kit

Exhaust

Hose

Screw

(5)

Pipe Clip

Pipe Hoop

(2)

Drainage Pipe

Rubber

Plug

Foam (adhesive and

non-adhesive) (6)

Installation Instructions

LOCATION

• The air conditioner should be placed on a ﬁ rm foundation to minimize noise

and vibration. For safe and secure positioning, place the unit on a smooth, level

ﬂ oor strong enough to support the unit.

• The unit has casters to aid placement, but it should only be rolled on smooth,

ﬂ at surfaces. Use caution when rolling on carpeted surfaces. Use caution and

protect ﬂ oors when rolling over wood ﬂ oors. Do not attempt to roll the unit over

objects.

• The unit must be placed within reach of a properly rated grounded socket.

• Never place any obstacles around the air inlet or outlet of the unit.

• Allow at least 30 cm of space away from the wall for efﬁ cient air conditioning.

WINDOW SLIDER KIT

INSTALLATION

NOTE: If the window opening is less than the mentioned minimum length of the

window slider kit, cut the end without the hole in it short enough to ﬁ t in the window

opening. Never cut out the hole in window slider kit (visit www.danby.com for

general instruction videos).

Your window kit has been designed to ﬁ t most “vertical” / “horizontal” windows up

to a maximum height of 80” (203 cm). For vertical window applications, multi lock

positions are provided on the edge of each slider section to secure each sliding

section together.

1. Select a suitable location, making sure you have access to an electrical outlet.

2. Install the ﬂ exible hose to the rear of the unit. Insert the hose collar on top of

the exhaust opening.

3. Install the adjustable Window Slider Kit as required.

4. Install the opposite end of the ﬂ exible exhaust hose into the window exhaust

adapter.

5. Install the window exhaust adapter into the opening in the slider section, mak-

ing sure the window slider sections are secure.

6. Plug the unit into a 115V/60Hz grounded electrical outlet.

Adjusting Plate

Cut if needed

Connector C

Width

Height

Screw

Installation Instructions

INSTALLATION IN A

DOUBLE-HUNG SASH

WINDOW

1. Measure the adhesive foam seal to ﬁ t the windowsill. Then cut the foam seal to

the proper length and attach it to the windowsill.

2. Adjust the length of the window slider kit to ﬁ t the width of the window. Shorten

the adjustable window kit to ﬁ t the width of the window if less than 70 cm (27.6

inches). Open the window sash and place the window slider kit on the window-

sill.

3. Cut the foam seal (adhesive type) to the proper length and attach it on the top

of the window slider kit. Close the window sash securely against the window

slider kit.

4. Cut the foam seal to an appropriate length and seal the open gap between the

top window sash and outer window sash.

Foam seal

(adhesive type)

Foam seal

Windowsill

Window Kit

Windowsill

Window Kit

70 cm - 203 cm

27.6 inches - 80 inches

Foam Seal

Installation Instructions

INSTALLATION IN A

SLIDING SASH

WINDOW

1. Measure the adhesive foam seal to ﬁ t the windowsill. Cut the foam seal (adhe-

sive type) to the proper length and attach it to the window frame.

2. Adjust the length of the window slider kit according to the height of the window,

shorten the adjustable window kit if the height of the window slider is less than

70 cm (27.6 inches). Open the window sash and place the window slider kit on

the windowsill.

3. Cut the foam seal (adhesive type) to the proper length and attach it to the top of

the window. Close the sliding sash securely against the window.

4. Cut the foam seal to an appropriate length and seal the open gap between the

top window sash and outer window sash.

Foam seal

(adhesive type)

Window

Kit

Foam

Seal

70 cm - 203 cm

27.6 inches -

80 inches

Foam

Seal

Features

ELECTRONIC CONTROL

INSTRUCTIONS

Before you begin, thoroughly familiarize yourself with the control panel and remote control and all its functions. Select the

functions you desire based on the associated symbol.

The unit can be controlled by the control panel alone or with the remote control.

Power Switch: Turns the unit ON/OFF.

Mode: Allows you to scroll through and select desired operating mode.

Temperature Adjust: Used for adjusting the thermostat. The default display is set temperature. In cooling

mode, when or button is pressed, the set temperature is displayed and may be adjusted. Temperature is

only adjustable in cool mode.

LED Display

MODE INDICATOR LIGHTS

Cooling Mode: When cool mode is selected, the indicator light will illuminate. During the cooling mode, the air

is cooled and hot air is exhausted outside through the exhaust tube. Adjust the fan speed to suit your desired

comfort level.

Note: The air exchange hose must vent outside the room when using cool mode.

Dehumidify Mode: When dehumidify mode is selected, the indicator light will illuminate. Air is dehumidiﬁ ed as

it passes through the unit, without being in full cooling mode.

Note: The warm air exchange hose must be vented outside the room when using dehumidifying mode.

Fan Mode: When fan mode is selected, the indicator light will illuminate.

Full Water Tank Indicator Light: Illuminates when the water tank is full.

Operating Instructions

Location of the remote control

• Use the remote control within a distance of 8 meters from the appliance, pointing it towards the receiver. Reception is

conﬁ rmed by a beep.

• The air conditioner will not operate if curtains, doors or other materials block the signals from the

remote control to the indoor unit.

• Prevent any liquid from falling into the remote control. Do not expose the remote control to direct

sunlight or heat.

• If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air conditioner may not

function properly. Use curtains to prevent the sunlight from falling on the receiver.

• If other electrical appliances react to the remote control, either move these appliances or call the service

depot.

CAUTION

REMOTE CONTROL

Control Buttons

Power Button

Mode Button

Temperature Adjustment Buttons

Fan Button

Sleep Button

Timer Button

LED Display Indicators

◄ Air Conditioning Mode

◄ Dehumidifying Mode

◄ Fan Mode

► Sleep Mode

Timer on

▲

Timer off

▲

Temperature Display

°C/°F Display

Fan Speed

► Child Lock

1. Power Button: Turns the unit on.

2. Mode Button: Each time the button is pressed, the operation mode changes in the following sequence:

COOL DRY FAN

3. Temperature Adjustment Buttons: Push these buttons to increase or decrease the indoor temperature setting by

1°C (1°F) increments. When the unit setting is on “Timer,” press these buttons to adjust the time. Note: When the unit

is off, the display on the remote will show the set temperature.

4. Fan Button: Used to select the fan speed in four steps:

AUTO

• After selecting, Cool or Fan mode, pressing the fan button will allow you to set your desired fan speed.

5. Sleep Button: Select this function if you want the unit to maintain a comfortable setting and save energy while you

sleep. The temperature setting will increase by 1°C (2°F) over the next hour and by another 1°C (2°F) over another

hour.

Operating Instructions

REMOTE CONTROL

6. Timer Button: When the unit is on, press the timer button to set the “Timer off” function. The “ ” and “.5H” icons

will start ﬂ ashing. Within 5 seconds, press the up and down buttons to adjust the time to indicate when you want the

unit to shut off. Release the button after you have achieved the time you desire. Then press the “timer” button again

to conﬁ rm. The “ ” and “.5H” buttons will stop ﬂ ashing.

When the unit is off, press the timer button to set the “Timer on” function. The “ ” and “.5H” icons will start ﬂ ashing.

Within 5 seconds, press the up and down buttons to adjust the time to indicate when you want the unit to turn on. Re-

lease the button after you have achieved the time you desire. Then press the “timer” button again to conﬁ rm. The

“ ” and “.5H” buttons will stop ﬂ ashing.

Note: Pressing the up or down button will increase or decrease the time by 0.5h, holding the up or down button will

allow you to change the time more rapidly.

To cancel the timer, press the “timer” button once to review the remaining time, within 5 seconds press “Timer” again

to cancel the timer function.

Child Lock Function:

You may lock the remote from being used by pressing the “ ” and “ ” buttons simultaneously on the remote. The lock

indicator will illuminate on the remote display. To turn the lock off, press the “ ” and “ ” buttons simultaneously again.

Note: The Child Lock Function is only available for the remote control. If the child lock is on, the buttons on the units con-

trol panel still function normally.

Note: When the Child Lock is initiated, the unit does not beep to indicate it is locked, the only indicator is the illumination

arrow on the display panel.

Note: (While the unit is OFF) To change the unit from °C to °F, press the “ ” and “ ” button simultaneously.

Note: To turn the LED display on/off, press “

” and simultaneously.

Operating Instructions

CHANGING THE BATTERIES ON THE REMOTE

• Protect the remote control from high temperatures, and keep it away from radiation exposure.

• Keep the control panel receiver out of direct sunlight.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh,etc) batteries.

• The remote operates within a range of 8 meters (26 ft.) from the receiver located inside the main unit. Any obstruction

between the receiver and remote may cause signal interference, limiting the ability to program the main unit.

This Class B digital apparatus complies with the Canadian ICES-003 standard. CAN ICES-3 (B)

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residen-

tial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and receiver.

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁ cations not approved by the party responsible for FCC compliance could void the user’s authority to

operate the equipment.

This appliance complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Battery replacement:

1. Push in the tab on the rear cover of the remote and pull off. Continue pulling

(gently) until the cover separates completely from the unit.

2. Insert (2) batteries (AAA) following the same orientation (polarity) depicted inside

the battery chamber (+/-).

3. Re-install rear cover.

4. If the remote control will not be used for extended periods of time (vacations

etc.), batteries should be removed.

To operate the hand-held remote control will require two “AAA” alkaline batteries (included). Batteries should be replaced

when:

a) No signal (beep) is heard when attempting to program the main unit.

b) The main unit does not respond to a command issued by the remote control.

Operating Instructions

AIR CONDITIONING

Important: The exhaust hose must be properly vented outdoors during air conditioning mode.

1. Press the POWER SWITCH key

to switch on the unit, and the previous set temperature will be shown in the

temperature display area of the display panel.

2. Press the MODE key

until the COOL indicator light illuminates. Each depression of the MODE key will ad-

vance to a different mode setting (Cool, Dehumidiﬁ er, Fan).

3. Press the appropriate increase or decrease buttons to select a suitable operating temperature setting.

Temperature settings are adjustable between 16°C (61°F) to 30°C (86°F).

4. Press the Fan key to select the desired fan speed setting. Your selection will appear on the display (each de-

pression of the fan key will advance to a different setting).

• Cooling stops automatically when the set temperature is achieved. Cooling resumes when the room temperature rises

above the “set” temperature level.

DEHUMIDIFIER

Note: During dehumidiﬁ er mode, the exhaust hose has to be vented outdoors.

1. Press the ON/OFF

key pad to switch the unit on.

2. Press the MODE key

until the DRY indicator illuminates on the display panel. Each press of the MODE key

will advance to a different mode setting (Cool, Dehumidiﬁ er, Fan).

Note: The warm air exchange hoses must vent outside the room when using dehumidiﬁ er mode.

FAN

Note: During fan mode, the exhaust hose does not have to be vented outdoors.

1. Press the POWER SWITCH

key to turn the unit on.

2. Press the MODE key

until the FAN indicator illuminates on the display panel. Each press of the MODE key

will advance to a different mode setting (Cool, Dehumidiﬁ er, Fan).

3. Press the FAN KEY

to select the desired FAN SPEED setting. Your selection will appear on the remote con-

trol. Each press of the fan key will advance to a different fan speed (High, Med., Low) as shown below.

Low Speed

Medium Speed

High Speed

NOTE: The fan is a continuously running fan and will not shut off when the unit is operating. This is to ensure

that the unit operates as efﬁ ciently as possible.

POWER OUTAGE

In the case of a power outage or interruption, the unit will automatically re-start with

the default settings after the power is restored.

Wait 3 minutes before resuming operation

After the unit has stopped, it cannot operate for the ﬁ rst 3 minutes. This is to protect

the unit. Operation will automatically start after 3 minutes.

AUTO

Operating Instructions

WATER DRAINAGE

When using the drain function, the PVC hose must be placed horizontally below the drainage hole. Avoid uneven ground

and folding the hose.

Note: Should you damage or misplace the PVC drain hose, a standard garden hose can be used.

1. Drain access water from the tank by placing a pan under the drain water

outlet (Fig. 4).

2. Remove the drain plug and let the water drain into the pan.

3. When the water stops draining out, replace the drain plug.

4. Remove the pan of water.

5. Operate the unit in Fan mode to dry the interior of the unit.

Fig. 4

The back of the unit.

1. Remove the plug at the drainage port. (Fig. 1)

2. Fix the drainage pipe clip on the right of the rear side plate near the drainage port with a screw. (Fig. 2)

3. Put the drainage pipe into the drainage port and screw it in. Place the drainage hose over a ﬂ oor drain.

4. When you are not using the continuous drain function, put the rubber plug into the other side of the drainage pipe, ﬁ x

it with the pipe hoop and then the drainage pipe clip. (Fig. 3)

Fig. 1

Fig. 2

Fig. 3

Plug

Drain Port

Drainage Pipe

Clip

Screw

Plug

Drainage Pipe

Clip

Pipe Hoop

Drainage Port

Drainage Pipe

Care and Maintenance

IMPORTANT

1. Be sure to unplug the unit before cleaning or servicing.

2. Do not use gasoline, paint thinner or other chemicals to clean the

unit.

3. Do not wash the unit directly under a tap or using a hose. It may

cause electrical damage.

4. If the power cord is damaged, contact the service depot immediately.

AIR FILTER

UNIT ENCLOSURE

Use a lint-free cloth soaked with neutral detergent to clean the unit enclosure,

be sure to wring the cloth of excess water. Finish by wiping with a clean dry

cloth.

LONG-TERM STORAGE

• Remove the rubber plug at the back of the unit and attach a hose to the drain

outlet. Place the open end of the hose directly over the drain area in your base-

ment ﬂ oor.

• Remove the plug from the bottom drain outlet, this means that all the water in

the bottom drain tray will drain out.

• Keep the appliance running on FAN mode for half a day in a warm room to dry

the appliance inside and prevent mold formation.

• Turn off the appliance and unplug it, wrap the cord and bundle it with tape.

• Remove the batteries from the remote control.

• Clean the air ﬁ lter and reinstall it.

Clean the air ﬁ lter at least once every two weeks. Accumulation of dust will hinder fan operation.

REMOVAL

This unit has two ﬁ lters. Lift the upper ﬂ iter out in the direction of the arrow (Fig. 25), then down. Remove the

lower ﬁ lter by loosening the screw and liﬁ ng out the ﬁ lter as shown in Fig. 25.

CLEANING

1. Wash the air ﬁ lter by submerging it gently in warm water (about 40°C / 104° F) with a neutral detergent.

2. Rinse the ﬁ lter and let it dry.

REINSTALL

Install the upper air ﬁ lter after cleaning, and install the lower ﬁ lter after, using the screw (see Fig. 26). *Filters

should dry before installing*

To remove the air ﬁ lter, pull the air ﬁ lter out in the direction of the arrow and remove the ﬁ lter.

Replace the air ﬁ lter and cover. *Filters should dry before installing*

Note: Always store the unit in the vertical position. DO NOT put heavy objects

on top of the unit.

Remove Reinstall

Troubleshooting

Occasionally, a minor problem may arise, and a service call may not be necessary- use this troubleshooting guide for

a possible solution. If the unit continues to operate improperly, call an authorized service depot or Danby’s Toll Free

Number for assistance.

Tel: 1-800-26- (1-800-263-2629)

PROBLEM POSSIBLE CAUSE SOLUTION

Unit does not work • Power is out

• The plug is not plugged in prop-

erly

• The full-tank indicator is ON; tank

is full

• Current leaking or pressing test

button on LCDI plug

• Wait for power to return

• Plug in properly

• Remove drain water from the

drain tank

• Press the reset button after re-

solving the problem

Compressor suddenly

stops during operation

• Indoor set temperature has been

reached

• The preset time is up

• The full-tank indicator is ON; tank

is full

• Reset the temperature level

• Reset the timer

• Remove drain water from the

drain tank

Unit runs intermittently • Malfunction

• Surrounding temperature is too

high/low

• Exhaust duct hose is blocked

• Contact your dealer

• This is normal

• Check the duct hose

Unit functions but the

room is not cooled

• Window or door is open in room

• There is a heat source or too

many people in the room

• Air intake grill is clogged

• Filter is too dirty

• Temperature setting is too high

• Close all windows/doors

• Move any heat sources from

room

• Clean air intake grill

• Replace or clean the ﬁ lter

• Lower temp. setting

Condensed water spills

out when moving the unit

• The tank is nearly full • Remove drain plug on rear bot-

tom and drain out water

Error Indicator Codes:

E5 - Surge protection: Disconnect the power, after 10 minutes turn the unit back on. If the warning still appears, please

contact a service provider.

H8 - Water tank is full: Drain water from the tank. If the warning still appears, please contact a service provider.

F1 - Malfunction of ambient temperature sensor: Please contact a service provider.

F2 - Evaporator sensor malfunction: Please contact a service provider.

F0 - Refrigerant leak or system blockage: Reset the unit by unplugging it for 30 minutes and then plugging it back in. If

the warning still appears, please contact a service provider.

H3 or E8 - Overload protection / malfunction: Check if the unit is operating under high temperature conditions. If the

ambient temperature is too high, turn the unit off until the ambient temperature drops below 35°C (95°F). Check to see

if something is obstructing airﬂ ow around the unit, if so, remove it. If the warning still appears, please contact a service

provider.

F4 - Condenser sensor is malfunctioning: Please contact a service provider.

La page charge ...

Danby DPA080C2SDB Le manuel du propriétaire

Marque: Danby

Modèle: DPA080C2SDB

Catégorie: Climatiseurs mobiles

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DPA080C2SDB Owner's manual

Danby DPA080C2SDB Le manuel du propriétaire

Danby DPA080C2SDB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents