Hobart CENTERLINE HMM20 Manuel utilisateur

Catégorie
Mélangeurs
Taper
Manuel utilisateur
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937-332-3000
www.hobartcorp.com
INSTRUCTION
MANUAL
MODEL
HMM20
FORM 45268 Rev. A (October 2018)
– 2 –
© HOBART, 2018
TABLE OF CONTENTS
GENERAL ............................................................................................................................................. 3
INSTALLATION .................................................................................................................................... 3
Unpacking ........................................................................................................................................ 3
Location ........................................................................................................................................... 3
Electrical Connections (Cord Connected Mixers) ............................................................................ 4
Check Initial Operation .............................................................................................................. 4
OPERATION ........................................................................................................................................ 5
STANDARD CONTROLS .................................................................................................................... 6
Model HMM20 (With Three Mix Speeds)......................................................................................... 6
Mixer Speeds ................................................................................................................................... 6
Button Function Description ............................................................................................................ 6
BOWL PLACEMENT ........................................................................................................................... 7
Agitator ............................................................................................................................................ 7
To Install ..................................................................................................................................... 7
To Remove ................................................................................................................................. 7
Prepare For Mixing .......................................................................................................................... 8
Mixing Modes .................................................................................................................................. 8
Timed Mixing Mode ......................................................................................................................... 9
Operating Notes .............................................................................................................................. 9
Unloading ...................................................................................................................................... 10
Wire Cage Assembly ..................................................................................................................... 10
Remove and Clean Bowl Guard Wire Cage .............................................................................11
Reinstall Bowl Guard Wire Cage ..............................................................................................11
Agitators and Attachments ............................................................................................................. 12
CLEANING ......................................................................................................................................... 13
MAINTENANCE ................................................................................................................................. 14
Lubrication ..................................................................................................................................... 14
Slideways ................................................................................................................................. 14
Planetary Seal ......................................................................................................................... 14
Adjustments ................................................................................................................................... 15
Agitator Clearance ................................................................................................................... 15
Measure Clearance ................................................................................................................. 15
Adjust the Bowl/Agitator Clearance ......................................................................................... 15
TROUBLESHOOTING ...................................................................................................................... 16
Service ........................................................................................................................................... 16
– 3 –
Installation, Operation and Care of
Centerline by Hobart 20-Quart Mixer
SAVE THESE INSTRUCTIONS
GENERAL
The Centerline by Hobart 20-quart mixer is a bench-type mixer which features three-speeds, a digital
timer, a manual bowl lift, and a #12 attachment hub as standard equipment.
A variety of attachments, agitators, and accessories are available. These are described in the Agitators
and Attachments section of this manual.
INSTALLATION
UNPACKING
The mixer was inspected before leaving the factory. The carrier assumes full responsibility for safe delivery
upon acceptance of the shipment. Check for possible shipping damage immediately after receipt.
If the mixer is found to be damaged, complete the following steps:
1. Carrier must be notifi ed within fi ve business days of receipt.
2. Carrier’s local terminal must be notifi ed immediately upon discovery (note the time, date, and who
was spoken to), and follow up and confi rm with written or electronic communication.
3. All original packing materials must be kept for inspection purposes.
4. The mixer cannot have been moved, installed, or modifi ed.
5. Notify Hobart customer care at (800) 333-7447.
LOCATION
Prior to installation, test the electrical service to ensure it agrees with the specifi cations on the machine
data plate.
Place the mixer on a suitable sturdy level surface. There should be adequate space around the mixer
for the user to operate the controls and to install and remove bowls. Holes are located in the base to
permanently secure the mixer, although this is not necessary in normal installations.
– 4 –
ELECTRICAL CONNECTIONS (Cord Connected Mixers)
The electrical cord on this machine is equipped with a three-pronged grounding
plug which must be connected to a properly grounded receptacle. If the receptacle is not the
proper grounding type, contact an electrician. DO NOT remove the grounding prong from the plug.
Electrical and grounding connections must comply with the applicable portion of
the National Electrical Code and/or other local electrical codes.
Check Initial Operation
1. Apply power to the mixer by inserting the cord plug into a properly grounded outlet.
2. Machine will beep three times indicating machine is ready.
3. Install the bowl on the bowl support and raise into the mix position, with the bowl support up and
bowl guard wire cage closed.
4. Turn the speed gear shift lever to 1.
5. Run the machine by pushing the ON/OFF button.
– 5 –
OPERATION
Moving agitator in bowl. Keep hands, clothing and utensils out of bowl while in
operation. Do not use without interlocked guard.
The Centerline by Hobart 20-quart mixer is equipped with a timer and controls. Refer to Fig. 1 for operating
parts and OPERATION section for their functions.
The bowl guard wire cage must be in closed position or the mixer will not operate.
The bowl must remain in mix position on bowl support, and the bowl support must be raised (mix position)
or the mixer will not operate.
Fig. 1
CONTROLS
ATTACHMENT
HUB
DRIP CUP
BOWL GUARD
WIRE CAGE
AGITATOR
SPLASH
GUARD
BOWL
SUPPORT
APRON
– 6 –
STANDARD CONTROLS
MODEL HMM20 (With Three Mix Speeds)
MIXER SPEEDS
SPEED 1 (Low) This speed is for heavy mixtures such as heavy batters, potatoes, pizza
dough, and bread dough.
SPEED 2 (Medium) This speed is for mixing cake batters and mashing potatoes.
SPEED 3 (High) This speed is for incorporating air into light batches, as well as nishing
whipped items.
BUTTON FUNCTION DESCRIPTION
NOTE: The machine will beep once when any button is pressed.
ON/OFF
Press the ON/OFF button to start the mixer. If the mixer is running,
press the ON/OFF button to stop the mixer.
SEC UP
ARROW
Press once to increase the time in 1 second increments. Press and
hold to quickly increase time until released. Range is 0-59.
SEC DOWN
ARROW
Press once to decrease the time in 1 second increments. Press and
hold to quickly decrease time until released. Range is 0-59.
MIN UP
ARROW
Press once to increase the time in 1 minute increments. Press and
hold to quickly increase time until released. Range is 0-59.
MIN DOWN
ARROW
Press once to decrease the time in 1 minute increments. Press and
hold to quickly decrease time until released. Range is 0-59.
NOTE: The seconds and minutes are set independently.
NOTE: The ON/OFF button is used to clear overload error.
Fig. 2
TIMER
DISPLAY
SECOND
UP
MINUTE
UP
SECOND
DOWN
MINUTE
DOWN
ON/OFF
SPEED GEAR
SHIFT LEVER
– 7 –
BOWL PLACEMENT
The bowl must be installed on the bowl support before the agitator is installed.
To install the bowl, lower the bowl support and move bowl clamps to the open position (Fig. 3). Position
the bowl so the alignment bracket on the back of the bowl is in the bowl retainer and the alignment pins
on the front of the bowl support t in the holes on the sides of the bowl. Lock the bowl in place by rotating
the bowl clamps (Fig. 4).
AGITATOR
To install an agitator, the bowl must be on the bowl support.
To Install
1. Lower the bowl.
2. Open the bowl guard wire cage.
3. Place the agitator inside the bowl and align the horizontal slot on the agitator with the agitator shaft
pin.
4. Slide the agitator up the agitator shaft and turn it clockwise to seat the shaft pin in the slot of the
agitator shank.
To Remove
1. Open the bowl guard wire cage.
2. Lower the bowl.
3. Lift the agitator and turn it counterclockwise. Slide agitator down and off the agitator shaft.
Fig. 3 Fig. 4
– 8 –
PREPARE FOR MIXING
1. Place the mixing bowl on the bowl support.
2. Pour ingredients into the bowl.
3. Place the agitator inside the bowl, and then
attach it to the agitator shaft (Fig. 5).
4. Lift bowl support.
5. Correctly close the bowl guard wire cage.
6. The mixer is now ready for mixing.
MIXING MODES
1. Turn the speed gear shift lever (Fig. 6) to select a mix speed. The timer display reads OFF (Fig. 6).
NOTE: GearSafe™ protects gears if speeds are changed during mixing operation without stopping machine.
2. Press the ON/OFF button (Fig. 7) to begin mixing. The timer display reads ON (Fig. 7).
NOTE: If the wire cage is opened or the bowl is lowered at any time, the mixing operation will stop. To
resume the mixing operation, close the wire cage or raise the bowl and press the ON/OFF button.
3. Press the ON/OFF button to stop the mixer. The timer display reads OFF.
4. Press the ON/OFF button to resume mixing if needed.
Fig. 5
Fig. 6 Fig. 7
SPEED GEAR
SHIFT LEVER
ON/OFF
BUTTON
– 9 –
TIMED MIXING MODE
1. Turn the speed gear shift lever (Fig. 6) to select a mix speed. The timer display reads OFF (Fig. 6).
2. Press the MIN UP/DOWN and SEC UP/DOWN arrows until the timer display reads the desired
mixing time (Fig. 8). This is the set time.
3. Press the ON/OFF button to begin mixing; the timer starts counting down from the set time.
4. To stop the mixer at any time, press the ON/OFF button. To resume mixing, press the ON/OFF
button. For example: The mixer is started at speed 1 for 30 seconds and is stopped after 10 seconds.
Pressing the ON/OFF button will resume the mixing operation and the remaining 20 seconds will
count down.
NOTE: If the wire cage is opened or the bowl is lowered at any time, the mixing operation will stop. To
resume the mixing operation, close the wire cage or raise the bowl and press the ON/OFF button.
5. When the timer reaches 00:00, the mixer stops and beeps three times. The count-down timer then
displays the last set time.
OPERATING NOTES
If the mixer is stopped during a mixing operation, the timer also stops. The timer starts again (with
the time remaining) when the ON/OFF button is pressed (Fig. 8).
Fig. 8
ON/OFF
BUTTON
– 10 –
UNLOADING
1. Open the bowl guard wire cage assembly.
2. Lower bowl support.
3. Remove the agitator from the agitator shaft.
4. Open the bowl clamps.
5. Lift the bowl off the pins and remove from the bowl support.
WIRE CAGE ASSEMBLY
The bowl guard wire cage assembly can be rotated out-of-the-way to the left to add ingredients or to
access the bowl and agitator.
Note how the plastic carriers allow the wire cage to ride around the circumference of the planetary drip cup.
Open the bowl guard wire cage; rotate it to your left (Fig. 9).
Close the bowl guard wire cage; rotate it to your right until it stops in the closed position (Fig. 10).
NOTE: The bowl guard wire cage must be returned to the closed position for the mixer to operate.
Fig. 9
Fig. 10
– 11 –
Remove and Clean Bowl Guard Wire Cage
Lower the bowl. Rotate the wire cage assembly to the left until it is positioned underneath the splash guard.
Remove the agitator and bowl.
While holding the wire cage assembly with both hands, rotate it completely to the left. When the front-center
retainer (Fig. 11) reaches the end of its travel, it can be lowered through the fl at (Fig. 11) on the ridge of
the drip cup (Fig. 11). After lowering the front-center retainer, move the wire cage assembly slightly to the
rear so the rear retainers clear the ridge on the drip cup. The wire cage assembly can now be lowered
and removed.
Wash the bowl guard wire cage assembly in a sink, rinse with clear water, and dry with a clean cloth.
The splash guard can be wiped off and/or washed with a cloth or sponge using warm, soapy water. Rinse
with clear water and dry with a clean cloth.
Reinstall Bowl Guard Wire Cage
Hold the wire cage assembly so its top ring is positioned around the planetary drip cup with the grooves
in both nylon rear retainers straddling the ridge on the drip cup at the rear. Lift the wire cage assembly so
the front-center retainer passes up through the at on the ridge of the drip cup and rotate the wire cage
assembly to the right. The wire cage assembly is properly assembled when all three retainers straddle
the ridge on the drip cup in three opposed locations. Rotate the wire cage assembly to the right until it
stops at the front-center position.
Rotate the wire cage out-of-the-way to the left to install or remove the agitator and bowl or to add ingredients.
Return the wire cage to its front-center position to operate the mixer.
Fig. 11
FRONT-CENTER
RETAINER
RIDGE
DRIP CUP
FLAT
– 12 –
AGITATORS AND ATTACHMENTS
20-Qt. Flat Beater 20-Qt. Wire Whip 20-Qt. Dough Hook
20-Qt. J Dough Hook 20-Qt. Bowl (SST)
20-Qt. Ingredient Chute 20-Qt. Table
– 13 –
CLEANING
Unplug machine power cord before beginning any cleaning procedure.
The mixer should be thoroughly cleaned daily. DO NOT use a hose to clean the mixer; it should be washed
with a clean, damp cloth. The base allows ample room for cleaning under the mixer. The apron (Fig. 1)
may be removed for cleaning by loosening the screws. The drip cup (Fig. 1) should be wiped clean. For
cleaning the bowl guard wire cage assembly, refer to page 11.
– 14 –
MAINTENANCE
Unplug machine power cord before beginning any maintenance procedure.
LUBRICATION
Slideways
The slideways (Fig. 12) should be lubricated approximately twice a year. To reach these areas, fully lower
the bowl support and remove the apron (Fig. 12), which is secured by screws. Wipe a thin coat of Lubriplate
630AA on each slideway. Install the apron.
Planetary Seal
Occasionally, the planetary seal (Fig. 13) may become dry and begin to squeak. To correct this, work a
little lubrication (mineral oil) under the lip of the seal.
Fig. 12 Fig. 13
PLANETARY
SEAL
SLIDEWAYS
(Behind Cover)
APRON
– 15 –
ADJUSTMENTS
Agitator Clearance
The agitator clearance should be checked periodically. The agitator must not touch the bowl.
The maximum clearance between the bottom of the bowl and the B fl at beater is 1/8" (3mm).
Install a bowl and agitator (e.g., beater). If the bowl and beater come into contact before the bowl support
reaches its stop, adjust the stop screw. Refer to Adjust the Bowl/Agitator Clearance.
Measure Clearance
Pour enough our in the bowl to cover the bottom of the bowl where the beater travels. With the bowl fully
raised (beater should not touch the bottom of the bowl), briefl y run the mixer at the lowest speed.
Turn off the mixer, disconnect the electrical power supply, and measure the depth of our where the beater
has traced a path. This measurement should be taken at several points around the bowl to assure accuracy.
Adjust the Bowl/Agitator Clearance
Remove the apron (Fig. 14), which is secured by screws.
Adjust the clearance by loosening the stop nut and moving the screw (Fig. 15) clockwise to increase
the clearance or counterclockwise to decrease the clearance.
After the adjustments are made, tighten the stop nut and replace the apron, and secure it with the
screws.
Carefully operate the bowl lift several times to check the adjustment.
Fig. 14 Fig. 15
APRON
STOP
NUT
SCREW
– 16 –
TROUBLESHOOTING
Symptoms Possible Causes
Mixer will not start Flashing time display – see below.
Branch circuit protector is in open position - check
fuse or disconnect switch.
Mixer is overloaded.
Wire cage is not in the closed position.
Bowl is not in closed (mix) position or bowl is not
in up position.
Agitator touches bowl Bowl is not in closed (mix) position.
Improper agitator clearance - see Maintenance
for adjustment procedure.
Agitator is not installed properly.
Planetary seal squeaks Seal requires occasional lubrication - see
Maintenance.
Timer display fl ashing time and machine is
beeping
If the timer display is fl ashing and machine
is beeping, press ON/OFF button to reset. If
symptom still exists, contact your local Hobart
Service offi ce.
Timer display reads OP (Fig. 16) Speed gear shift lever is not properly seated.
SERVICE
If service is needed on this equipment, contact your local Hobart Service offi ce at (888) 4HOBART.
Fig. 16
SPEED GEAR
SHIFT LEVER
FORM 45268 Rev. A (October 2018) PRINTED IN U.S.A.
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937-332-3000
www.hobartcorp.com
MANUEL
D’INSTRUCTION
MODÈLE
HMM20
FORMULAIRE 45268 Rév. A (octobre 2018)
– 2 –
© HOBART, 2018
TABLE DES MATIÈRES
RENSEIGNEMENTS GÉNÉRAUX ..................................................................................................... 3
INSTALLATION .................................................................................................................................... 3
Déballage ........................................................................................................................................ 3
Emplacement ................................................................................................................................... 3
Raccordements électriques (batteur-mélangeur à fi l) ...................................................................... 4
Contrôler la première utilisation ................................................................................................. 4
FONCTIONNEMENT ........................................................................................................................... 5
COMMANDES STANDARD ................................................................................................................ 6
Modèle HMM20 (avec trois vitesses de mélange) ........................................................................... 6
Vitesses du batteur-mélangeur ........................................................................................................ 6
Description des fonctions des boutons ............................................................................................ 6
MISE EN PLACE DU BOL ................................................................................................................... 7
Agitateur .......................................................................................................................................... 7
Assemblage ............................................................................................................................... 7
Retrait ........................................................................................................................................ 7
Préparation pour le mélange ........................................................................................................... 8
Modes de mélange .......................................................................................................................... 8
Mode de mélange minuté ................................................................................................................ 9
Notes sur l’opération ........................................................................................................................ 9
Déchargement ............................................................................................................................... 10
Grille de protection ........................................................................................................................ 10
Retrait et nettoyage de la grille de protection du bol ................................................................11
Mise en place de la grille de protection ....................................................................................11
Agitateurs et accessoires .............................................................................................................. 12
NETTOYAGE...................................................................................................................................... 13
ENTRETIEN ....................................................................................................................................... 14
Lubrifi cation ................................................................................................................................... 14
Glissières ................................................................................................................................. 14
Joint planétaire ........................................................................................................................ 14
Réglages ....................................................................................................................................... 15
Distance de dégagement de l’agitateur ................................................................................... 15
Mesurer la distance de dégagement ....................................................................................... 15
Réglage de la distance de dégagement du bol/agitateur ........................................................ 15
DÉPANNAGE ..............................................................................................................................
....... 16
Service ........................................................................................................................................... 16
– 3 –
Installation, utilisation et entretien du
batteur-mélangeur de 20 pte Centerline par Hobart
CONSERVEZ CES INSTRUCTIONS
RENSEIGNEMENTS GÉNÉRAUX
Le batteur-mélangeur de 20 pte Centerline par Hobart est un batteur-mélangeur sur socle qui comporte
trois vitesses, une minuterie numérique, un bol à levage manuel et un moyeu de xation 12 en tant
que matériel normalisé.
Une variété d'agitateurs et d'accessoires sont disponibles. Ceux-ci sont décrits dans la section Agitateurs
et accessoires de ce manuel.
INSTALLATION
DÉBALLAGE
Ce batteur-mélangeur a été inspecté avant de quitter l'usine. La société de transport assume l'entière
responsabilité de la livraison en bon état du fait de l'acceptation de l'expédition. Inspectez le batteur-
mélangeur dès sa réception pour des bris dus au transport.
Si vous constatez que le batteur-mélangeur est endommagé, procédez comme suit :
1. La société de transport doit être notifi ée dans les cinq jours ouvrables suivant la réception du robot
culinaire.
2. La société de transport doit être notifi ée immédiatement une fois le dommage constaté (notez l'heure,
la date et la personne de contact), et faites un suivi de la notifi cation et confi rmez-la au moyen de
communication écrite ou électronique.
3. Tous les matériaux d'emballage originaux doivent être conservés aux fi ns d'inspection.
4. Le batteur-mélangeur ne peut pas avoir été déplacé, installé ou modifi é.
5. Communiquez avec le service à la clientèle de Hobart au 1 800 333-7447.
EMPLACEMENT
Avant d’installer le batteur-mélangeur, vérifi ez que le service électrique est conforme aux spécifi cations
sur la plaque signalétique de l’appareil.
Placez le batteur-mélangeur sur une surface de niveau solide et appropriée. Il devrait y avoir suffi samment
d'espace autour du batteur-mélangeur pour que l'utilisateur puisse actionner les commandes et installer et
retirer les bols. Des trous sont situés dans la base pour xer de manière permanente le batteur-mélangeur,
bien que cela ne soit pas nécessaire dans les installations normales.
– 4 –
RACCORDEMENTS ÉLECTRIQUES (batteur-mélangeur à fi l)
AVERTISSEMENT
Le cordon d'alimentation sur cette machine est doté d'une che de terre à trois
broches qui doit être branchée à une prise correctement mise à la terre. Si la prise n’est pas de type
de mise à la terre, contactez un électricien. N'enlevez PAS la broche de mise à la terre de la fi che.
AVERTISSEMENT
Les raccordements électriques et de mise à la terre doivent être conformes aux
parties applicables du National Electrical Code et/ou d'autres codes électriques locaux.
Contrôler la première utilisation
1. Mettez le batteur-mélangeur sous tension en insérant la che du cordon dans une prise correctement
mise à la terre.
2. Le batteur-mélangeur émet trois bips indiquant que l’appareil est prêt.
3. Installez le bol sur le support à bol et relevez-le dans la position pour mélanger, avec le support à
bol vers le haut et la grille de protection du bol en position fermée.
4. Tournez le levier de changement de vitesse vers 1.
5. Faites fonctionner l’appareil en appuyant sur le bouton ON/OFF (marche/arrêt).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Hobart CENTERLINE HMM20 Manuel utilisateur

Catégorie
Mélangeurs
Taper
Manuel utilisateur