Hobart ML-141105 Manuel utilisateur

Catégorie
Mélangeurs
Taper
Manuel utilisateur

Ce manuel convient également à

701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com
INSTRUCTION
MANUAL
MODELS
HL600 & HL662
ML-141104
ML-141105
F45239 (December 2013)
– 2 –
TABLE OF CONTENTS
GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . 4
Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electrical Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Bowl Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Agitator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power Bowl Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Prepare for Mixing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Timer Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operating Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Unloading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Wire Cage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Agitators and Attachments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CLEANING. . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . 19
© HOBART, 2013
– 3 –
INSTALLATION, OPERATION AND CARE OF
LEGACY
®
60 QUART MIXERS
SAVE THESE INSTRUCTIONS
GENERAL
The Legacy
®
60 quart mixer series are heavy-duty mixers which feature a 2.7 horsepower motor,
SmartTimer
, a power bowl lift and a #12 attachment hub as standard equipment.
The Legacy
®
series is available in three models:
The HL600 is equipped with Stir, plus four mixing speeds.
The HL662 is equipped with two mixing speeds.
A 40 quart bowl and agitators are also available.
A variety of attachments, agitators and accessories are available. These are described in a separate Use
and Applications Handbook, which is furnished on the Legacy
®
Mixer Operator Training CD provided with
each mixer.
– 4 –
INSTALLATION
UNPACKING
Immediately after unpacking the mixer, check for possible shipping damage. If this machine is found
to be damaged after unpacking, save the packaging material and contact the carrier within 15 days of
delivery.
LOCATION
Prior to installation, test the electrical service to assure that it agrees with the speci cations on the machine
data plate.
Place the mixer in its operating location. There should be adequate space around the mixer for the user
to operate the controls and to install and remove bowls. The area above and to the right side of the mixer
should allow the top and side covers to be removed for routine maintenance and servicing.
Once in position, the mixer must be leveled:
Remove the two top cover screws and the top cover.
Place a level on the top rim of the large pulley (Fig. 1). Slide shims under the base contact surface
of the mixer as required to level it front-to-back and side-to-side.
Do not replace the top cover until installation is completed.
Check Lubrication Before Use
This mixer is shipped with oil in the transmission. Check oil level before starting mixer. Refer to Lubrication
on
page 15 for applicable lubrication procedures.
Transmission Fill Plug / Oil Dipstick
Fig. 1
Top Rim
– 5 –
ELECTRICAL CONNECTIONS
Electrical and grounding connections must comply with the applicable portion
of the National Electrical Code and/or other local electrical codes.
DISCONNECT the ELECTRICAL POWER to the machine and follow lockout /
tagout procedures.
A hole for 3/4"-trade-size conduit is located at the top of the pedestal. Make electrical connections per the
wiring diagram located on the inside of the top cover.
Single-Phase Mixer:
Connect eld supply lead wires to L1 and L2.
Connect ground wire to ground lug on the mixer.
Cut off stripped portion of L3 on Legacy
®
Mixer and wrap securely with electrical tape to insulate
the exposed conductor.
Three-Phase Mixer:
Connect eld supply lead wires to L1, L2 and L3.
Connect ground wire to ground lug on the mixer.
Check Initial Operation
1. Apply power to the mixer.
2. Turn the SPEED dial pointer to STIR for the HL600 and to 1 for the HL662.
3. Install the bowl and lock into mix position, with the Bowl Support all the way up and bowl guard
closed. Momentarily run the machine by pushing the START and then STOP buttons.
– 6 –
OPERATION
Moving agitator in bowl, keep hands, clothing and utensils out while in
operation. Do not use without interlocked guard.
The Legacy
®
mixer is equipped with SmartTimer
controls and a power bowl lift. Other operating parts
(Fig. 2) and their functions are described throughout the Operation section.
The Wire Cage must be in position or the mixer will not operate.
The bowl must stay in locked position on Bowl Support or the mixer will not operate.
If the Bowl Support is not all the way up (mix position), the mixer will not operate unless the START button
is pressed and held.
If the Bowl Support is not at the mix position and the START button is pressed and held, the mixer will
operate only in Stir speed.
Fig. 2
Controls
Attachment Hub
Wire Cage
Drip Cup-
Splash
Guard
Assembly
Agitator
Apron
Bowl Lock Lever
Bowl Support
– 7 –
CONTROLS
Model HL600 (With Four Mix Speeds Plus Stir Speed)
Model HL600 Mixer Speeds
STIR (Slow) STIR speed is for incorporating ingredients at the start of each mixing
process.
Speed 1 (Low) This speed is for heavy mixtures such as pizza dough, heavy batters and
potatoes.
Speed 2 (Medium-low) This speed is for mixing cake batters, mashing potatoes and developing
bread dough.
Speed 3 (Medium-high) This speed is for incorporating air into light batches, as well as nishing
whipped items.
Sped 4 (High) This speed is for maximum and accelerated air incorporation into light
batches.
Starts Mixer
Stops Mixer
Speed Selector
Time Selector
Raises and Lowers
Mixing Bowl
Displays Selected
Mix Speed
Displays
Mixing Time
– 8 –
Model HL662 (With Two Mix Speeds Plus Meat Grind, Cheese Shred, Vegetable Slice Speeds)
Model HL662 Mixer Speeds
SPEED 1 (Slow) This speed is for heavy mixtures such as pizza dough.
SPEED 2 (Low) This speed is for developing pizza dough.
MEAT GRIND This speed is for grinding meat.
CHEESE SHRED This speed is for shredding cheese.
VEGETABLE SLICE This speed is for slicing vegetables.
Starts Mixer
Stops Mixer
Displays Selected
Mix Speed
Displays
Mixing Time
Speed Selector
Time Selector
Raises and Lowers
Mixing Bowl
– 9 –
BOWL PLACEMENT
The bowl must be installed before the agitator is installed.
To install the bowl, fully lower the bowl support. Position bowl so the alignment pins on the left side of the
bowl support t in the holes in the bowl. Swing the bowl into the locked position on bowl support.
AGITATOR
To install an agitator, the bowl must be on the bowl support and fully lowered.
To Install
1. Open the wire cage.
2. Place the agitator inside the bowl and line up the
horizontal slot on the agitator with the agitator shaft
pins.
3. Slide the agitator up the agitator shaft until it stops
and latches.
To Remove
1. Open the wire cage.
2. Lower the bowl by pressing and holding the down
arrow on the bowl switch.
3. Hold the agitator and pull the plunger of the agitator out
(Fig. 3). Slide agitator down off the agitator shaft.
POWER BOWL LIFT
CAUTION: Before lowering the bowl onto a bowl truck, always unlock bowl and swing bowl out
slightly.
To raise the bowl, the bowl must be in the locked position. Push and hold the up arrow on the bowl
switch.
To lower the bowl, push and hold the down arrow on the bowl switch.
To Raise the Bowl While Mixing
To raise the bowl while the agitator is mixing the product (when required by recipe or when using the Bowl
Scraper Attachment):
1. Close the wire cage, then select a mixing speed on the SPEED dial.
2. Select a count-down time or HOLD for continuous count-up mixing.
3. While pressing and holding the up arrow on the bowl switch, press and hold the START button.
The mixer runs only in stir speed while the bowl is rising.
4. When the bowl reaches the mix position, release the START button. The mixer automatically
changes to the selected mixing speed.
Fig. 3
– 10 –
PREPARE FOR MIXING
1. Place the mixing bowl on the bowl support.
2. Pour ingredients into the bowl.
3. Swing the bowl back to the locked position.
4. Place the agitator inside the bowl, then attach
it to the agitator shaft (Fig. 4).
5. Return the wire cage to front-center position.
6. Push and hold the up arrow on the bowl switch
until the bowl reaches the mix position and stops.
7. The mixer is now ready for mixing. (See Timer
Operation.)
TIMER OPERATION
Using the Count-Up Mode (Continuous Mixing)
1. Turn the SPEED dial to select a mix speed (the SPEED setting can be changed at any time dur-
ing the mixing operation).
NOTE : STIR is to be used for incorporating ingredients. Do not use to develop dough products.
2. Set the timer on hold by turning the TIME selector counterclockwise until "Hold" appears in the
TIME window.
3. Press the START button to begin mixing. The timer starts counting forward from 00:00.
NOTE: If the wire cage is opened at any time, the mixing operation will stop. To resume the mix-
ing operation, close the wire cage and press the START button.
4. Use the STOP button to stop the mixer; the mixing time is displayed in the TIME window.
5. Press the start button to resume mixing if needed.
NOTE: When the timer reaches 20:00 minutes, it will rollover to 00:01 and continue counting until
the STOP button is pressed.
Wire Cage
Dough Hook
Accessory
Fig. 4
– 11 –
Using the Count-Down Mode (Timed Mixing)
1. Turn the SPEED dial to select a mix speed.
a. If the count-up mode was used for the previous batch, the desired time needs to be entered.
b. If the count-down mode was used for the previous batch, the previous time will be displayed. If
a different time is needed, turn the TIME selector to the desired time.
2. Press the START button to begin mixing; the timer starts counting down from the set time.
a. To stop the mixer at any time, press the STOP button. To resume mixing, press the START
button. For example: The mixer is started at SPEED 1 for 30 seconds and is stopped after 10
seconds. Pressing the START button will resume the mixing operation.
b. If the mixer is stopped and a new time setting is entered, pressing the START button saves
the new time setting on the current speed selection. For example: The mixer is started at
SPEED 1 for 30 seconds and is stopped after 10 seconds. A new time is entered by turning
the TIME selector. The new time will replace the initial 30 seconds for SPEED 1 after the
START button is pressed.
c. If the time is changed while mixing, the mixer will operate until the new time expires. The
adjustment to the time will not be stored.
d. If speed is changed while mixing, the time will change to the previous time for the selected
speed and count down.
NOTE: If the wire cage is opened at any time, the mixing operation will stop. To resume the mix-
ing operation, close the wire cage and press the START button.
3. When the timer reaches 00:00, the mixer stops; a beeper sounds for 3 seconds. The count-down
timer displays the last-entered time.
OPERATING NOTES
STIR is to be used for incorporating ingredients. Do not use it to develop dough products.
If the mixer is stopped during a mixing operation, the timer also stops. The timer starts again
where it left off when the START button is pressed.
The SPEED window will display the SPEED dial's current speed selection. Turn the Time selector
clockwise to take the mixer out of the hold mode.
– 12 –
UNLOADING
1. Unlock the bowl and swing-out slightly. Press and hold the down arrow on the bowl switch to
lower the bowl.
2. Open the wire cage assembly.
3. Remove the agitator from the agitator shaft.
4. Remove the bowl from the bowl support.
WIRE CAGE (Fig. 5)
The wire cage can be rotated out of the way to add ingredients or to access the bowl and agitator.
Note how the grooves on the nylon retainer shoes allow the Wire Cage to ride around the circular ridge
of the planetary drip cup.
To open the wire cage, rotate it to your left.
To close the wire cage, rotate it to your right until it stops in the front-center, closed position.
NOTE: The wire cage must be returned to the closed position for the mixer to operate.
Front-Center Retainer Shoe
Drip Cup-
Splash
Guard
Assembly
Wire Cage Front-Center Position
Rear Retainer Shoe
Circular Ridge on
Planetary Drip Cup
Wire Cage Rotated Left
Fig. 5
– 13 –
Remove and Clean Wire Cage (Fig. 6)
1. Lower the bowl. Remove the agitator and bowl.
2. While holding the wire cage securely with both hands, rotate it to your left until the front-center
retainer shoe reaches the gap in the circular ridge of the planetary drip cup.
3. Lower the front of the wire cage and move the wire cage slightly to the rear so the rear retainer
shoes clear the ridge of the drip cup. The wire cage can now be removed.
4. Wash the wire cage in a sink, rinse with clear water, and dry with a clean cloth.
5. The stainless steel splash guard can be wiped off and/or washed with a cloth or sponge using
warm, soapy water. Rinse with clear water and dry with a clean cloth.
Reinstall Wire Cage
1. Position the ring of the wire cage so the front-center retainer shoe is positioned below the gap in
the circular ridge of the planetary drip cup.
2. Position the grooves so the rear retainer shoes straddle the circular ridge on the planetary drip
cup.
3. Lift the front of the wire cage so the front-center retainer shoe passes up through the gap in the
circular ridge on the planetary drip cup.
4. Rotate the wire cage to your right until all three retainer shoes straddle the ridge on the drip cup.
5. Continue rotating the wire cage so the opening is to the front of the mixer (to install the agitators)
or until it stops at the front-center position.
AGITATORS AND ATTACHMENTS
Attachments for attachment hub and agitators are covered in a separate Hobart Legacy
®
Mixer Use and
Application Handbook on the Mixer Operator Information CD. Follow the instructions accordingly.
Front-Center Retainer Shoe
Gap in Circular Ridge
Fig. 6
– 14 –
CLEANING
DISCONNECT the ELECTRICAL POWER to the machine and follow lockout /
tagout procedures.
New mixer bowls and accessories (beaters, whips and dough arms) should be thoroughly washed with hot
water and a mild soap solution, rinsed with either a mild soda or vinegar solution and thoroughly rinsed with
clear water before being used. This cleaning procedure should also be followed for bowls and agitators
before whipping egg whites or whole eggs.
The mixer should be thoroughly cleaned daily. DO NOT use a hose to clean the mixer; it should be washed
with a clean, damp cloth. The base allows ample room for cleaning under the mixer. The apron (Fig. 2,
page 6) may be removed for cleaning by loosening the thumb screws.
The drip cup-splash guard assembly (Fig. 2, page 6) should be removed periodically and wiped clean.
For cleaning the Wire Cage refer to page 13.
– 15 –
MAINTENANCE
DISCONNECT the ELECTRICAL POWER to the machine and follow lockout /
tagout procedures.
LUBRICATION
Slideway
The slideways (Fig. 7) should be lubricated approximately twice a year. To reach these areas, fully lower
the bowl support and remove the apron, which is secured by thumb screws. Wipe a thin coat of Lubriplate
630AA on the bowl pad area of the bowl supports and on each slideway. Install the apron.
Planetary Seal
Occasionally, the planetary seal (Fig. 7) may become dry and begin to squeak. To correct this, work a little
lubrication (mineral oil) under the lip of the seal.
Planetary Seal
Slideway
Fig. 7
– 16 –
Transmission
To check the oil level, remove the top cover, which is secured by two screws. Remove the Transmission Fill
Plug (Fig. 8) and check the oil level. If the oil level is below the line on the oil dipstick, add a small amount
of the recommended transmission oil until it returns to the proper level. Do not over ll the transmission, as
leakage may result. Contact your local Hobart Service Of ce for the recommended transmission oil.
ADJUSTMENTS
Agitator Clearance
The agitator clearance should be checked periodically. The agitator must not touch the bowl, and the
maximum clearance between the bottom of the bowl and the B at beater is 1/8" (3 mm); the maximum
clearance between the bottom of the bowl and the ED dough arm is 5/16" (8 mm).
Install a bowl and agitator (e.g., beater). If the bowl and beater come into contact before the bowl support
reaches its stop, adjust the stop screw. Refer to Adjust the Bowl/Agitator Clearance, page 17.
Transmission Fill Plug/Oil Dipstick
Fig. 8
– 17 –
Measure Clearance
Pour enough our in the bowl to cover the bottom of the bowl where the beater travels. With the bowl fully
raised (beater should not touch the bottom of the bowl), brie y run the mixer at the lowest speed.
Turn off the mixer, disconnect the electrical power supply, and measure the depth of our where the
beater has traced a path. This measurement should be taken at several points around the bowl to assure
accuracy.
Adjust the Bowl/Agitator Clearance
Remove the apron (which is secured by thumbscrews).
Adjust the stop screw on right side.
- Loosen the bottom locking nut, (Fig. 9) and turn
the stop screw counterclockwise to increase
the clearance or clockwise to decrease the
clearance.
- Tighten the locking nut while holding the stop
screw.
After the adjustments are made, replace the apron
and secure it with the thumbscrews.
Reconnect the electrical power supply.
Carefully operate the bowl lift several times to
check the adjustment.
Bowl Lock Lever
Occassionally debris may collect and cause
the lever to move slowly.
Pour very warm water around lock pin to ush
out food particles that may have collected
there. The water should ow through, around
the pin. Be sure to have a cloth or dish under
to bowl support to catch the water and food
particles.
Lubricate the pin with a thin coat of lubriplate
630AA.
Stop Screw &
Locking Nut
Fig. 9
Bowl Lock Lever
– 18 –
TROUBLESHOOTING
Symptoms Possible Causes
Mixer will not start. Circuit protector is in open position - check fuse or
disconnect switch.
Mixer is overloaded.
Wire cage is not in the closed position.
Bowl is not in closed (locked) position.
Agitator touches bowl. Bowl is not in closed (locked) position.
Improper agitator clearance - see Maintenance for
adjustment procedure.
Agitator is not installed properly.
Planetary seal squeaks. Seal requires occasional lubrication - see Maintenance.
Timer displays error code (ErXX). If the error code is ashing - wait for mixer to clear error
condition. If mixer continues to stop and timer displays
ashing error code, disconnect electrical power from
mixer for 1 minute, then reconnect. If symptoms still exist,
contact your local Hobart Service of ce.
– 19 –
SERVICE
If service is needed on this equipment, contact your local Hobart Service of ce.
– 20 –
F45239 (December 2013) PRINTED IN U.S.A.
NOTES
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Hobart ML-141105 Manuel utilisateur

Catégorie
Mélangeurs
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues