Hobart FT1000S-ER Mode d'emploi

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

937 332-3000

www.hobartcorp.com

F47504 (April 2016)

FT1000-SERIES DISHWASHERS

LAVE-VAISSELLE DE LA GAMME FT1000

LAVAVAJILLAS SERIE FT1000

MODEL

MODÈLE

MODELO

FT1000

FT1000-ER

FT1000-ER-BD

FT1000-ADV

FT1000S

FT1000S-ER

FT1000S-ER-BD

– 2 –

– 3 –

TABLE OF CONTENTS

OPERATION ..................................................................4

Machine Preparation – Check before beginning operation ............................4

  Tanklling .................................................................5

Dishwashing ...............................................................6

Empty Strainer Baskets As Necessary ........................................7

Loading ................................................................7

Unloading ..............................................................8

Recommended Minimum Temperatures ..........................................8

Conveyor Speed Adjustment ...................................................8

CLEANING ...................................................................8

Deliming(ManualprocessformachinesnotequippedwithAutoDelime) ................10

Automatic Soil Removal Section(When Equipped). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

AutoClean(WhenEquipped) .................................................12

AutoDelime(WhenEquipped) ................................................12

DosandDon'tsforYourNewHobartWarewasher .................................13

Curtains:ModelsFT1000,FT1000-ER,FT1000-ER-BD,&FT1000-ADV ................14

Curtains:ModelsFT1000S,FT1000S-ER,&FT1000S-ER-BD .......................15

PROGRAMMING ..............................................................16

  MachineOperationandProgrammingSecurityLevels ..............................16

Operator – O ...........................................................16

SuperOperator – SO .....................................................16

Manager – M ..........................................................17

User Programming Instructions ................................................17

  MenuDisplayPrompts .......................................................18

Entering the Manager Menu ..................................................18

About Screen ..............................................................18

Actions Menu ..............................................................19

Logs Menu ................................................................19

Operation Parameters Menu ..................................................20

MAINTENANCE ..............................................................23

Line Strainers ..............................................................23

Lubrication ................................................................23

Motors ................................................................23

Conveyor Gearmotor ....................................................23

Conveyor Drive Chain ...................................................23

Conveyor Take-Up Unit ..................................................24

TROUBLESHOOTING .........................................................25

– 4 –

Operation and Care Of

FT1000 SERIES DISHWASHERS

SAVE THESE INSTRUCTIONS

OPERATION

MACHINE PREPARATION – CHECK BEFORE BEGINNING OPERATION

Openthemachinedoorsandmakesureallcomponentsareintheirproperoperating

positions before beginning operation.

• Allstrainerpansandscrapbasketsmustbeproperlyinstalledineachsection

(Fig.1).

Fig. 1

• Theexternalscrapbasket(s)mustbeproperlyinstalledbeneaththeloadofthe

machine(Fig.2).

Fig. 2

• Allupperandlowerwasharmsmustbeproperlyinstalledineachsection.Wash

armslidersmustalsobeplacedintheclosedposition(Figs.3&4).

Fig. 3 Fig. 4

– 5 –

• Thedualrinseandnalrinsearmsmustbeproperlyinstalled(Figs.5&6).

Fig. 5 Fig. 6

• OnmachinesequippedwiththeASRsection,theASRarms,strainerpan,and

soilcollectorstandpipemustbeproperlyinstalled(Figs.7&8).

Fig. 7 Fig. 8

• Allcurtainsmustbeproperlyinstalledasshownonpages14-15ofthismanual.

• Alltankdrainsmustbeplacedintheclosedposition.

Masterdrain(onlymachinesequippedwithAutoCleanandAutoDelime)

mustbeplacedintheopenposition.

TANK FILLING

Allwater(andsteam,ifequipped)supplyvalvesmustbeopenedandtheelectric

supplyturnedonbeforethemachinewillfunction.

Closealldrainsanddoors.Thedrainhandlesarelocatedneartheooratthefront

ofeachtank.Swingdrainhandlestotherighttocloseandtothelefttoopen.(On

machinesequippedwithAutoCleanandAutoDelime,opentheMasterDrainlocated

ateithertheloadorunloadendoftheunit.SwingtheMasterDrainhandletothe

righttoopenandtothelefttoclose.)

– 6 –

PressthePowerkeyonthekeypadlocatedonthedoorofthecontrolbox(Fig.9).

Thedisplaywilllightup.

POWER

Fig. 9

Ifdoor(s)arenotclosed,Door(s) Opendisplays.Ifdrain(s)arenotclosed,Drain(s)

Opendisplays.Ifalldoorsanddrainsareclosed,Tank(s) Fillingdisplaysandtanks

begintoll.

NOTE: Openingadoorduringthellcycleshutsoffthellvalves…Door(s) Open

displays.Closethedoortoresumethellcycle(Tanks Fillingdisplays).

Afterthewaterlevelraisestheloweroatineachtank,thewash,rinseanddual

rinsetanksbegintoheat.Whenalltanksarefullthellvalveswillautomatically

shutoffandthewatertemperaturesdisplayforeachtank.

TheMaintenanceFillfeatureaddswatertothetankstomaintainproperwaterlevels

duringoperation.Ifthewaterleveldropsbelowtheloweroatinanytank,theheat

shutsoffandllingresumesontheaffectedtank(s).Whenthewaterlevelreaches

theloweroat,heatingresumeswhilethetank(s)continue(s)llinguntiltheproper

waterlevelisreached.

DISHWASHING

Startthemotorsfortheconveyor,pumpsandblowerdryer(ifequipped)bypressing

thegreenSTARTswitchlocatedateithertheloadorunloadendofthemachine

(Fig.10)oronthekeypadlocatedonthefrontofthecontrolbox(Fig.11).The

machinewilloperateonlyifthetankshavelledtotheproperlevelandalldoors

areclosed.PresstheredSTOPswitch(Fig.10or11)tostoptheconveyor,pumps

andblowerdryermotors.

STOP (red)

START (green)

START

STOP

Fig. 10 Fig. 11

– 7 –

Alltanktemperaturesdisplayonthekeypaddisplaywhenthemachineisinoperation.

FinalRinsetemperaturereads‘---‘untilwarereachestherinsezone.Whenware

reachestherinsezone,theFinalRinsewatertemperaturedisplays.Aftertheware

exitstherinsezone,FinalRinsetemperatureagainreads‘---‘.

Ifwarereachestheunloadendofthemachineandtripsthedishlimitswitch,the

conveyorandnalrinseshutoff,andthekeypaddisplaysthetanktemperatures

alongwithUnload Dishes across the bottom. After the ware is removed and the

dishlimitreturnstooperatingposition,normaloperationresumes.Ifwareisnot

unloaded,theDishLimitAuto-Timercountsdownforoneminute,andthenshuts

offpumpsandblowerdryer(ifequipped).Thedisplaycontinuestoshowthetank

temperatures and Unload Dishes.

Ifnowareentersthemachineforapresetamountoftime,theAuto-Timerautomatically

shutsoffthemachineandtankscontinuetomaintainrequiredtemperatures.To

resumeoperation,pressthegreenSTARTswitchlocatedateitherendofthemachine

oronthekeypadlocatedonthefrontofthecontrolbox.

NOTE: The Auto-Timer shut off setting can be adjusted as shown in the Parameters

Menu(page20);therangeisfrom1to30minutes.

Empty Strainer Baskets As Necessary

Thestrainerbasketscanllwithfoodsoilduringoperationwhichwillaffectdishwasher

operationandthereforemustbeemptiedperiodically.STOPthemachineandopen

theaccessdoors;strainerbasketsareimmediatelyinsideatthefrontofthetanks.

Theexternalscrapbasket(s)attheloadsectionneedstobeemptiedperiodically,

andcanbedonewithoutinterruptingmachineoperation.Removethebasket(s)

whenlledwithfoodsoil,emptyandreplacewhendone.

Loading

Pre-scrapdishesthoroughlytoremovelargefoodparticlesanddebris.Neveruse

steelwoolonwaretobeloadedintothedishwashingmachine;thiscouldintroduce

surfacecorrosionwhichcouldeventuallyinterferewithmachineoperation.

Allplates,saucers,trays, etc.should beloadedontheconveyorin an inclined

position. Bowls should beloaded upside down. Silverware must be washedin

rackstopreventlossofitems;failingtodosocouldcausetheconveyortojamand

damage ware or machine components.

DONOTattempttowashlargeitems(pots,pans,trays,etc.)withoutrstchecking

tomakesuretheytthroughthemachineopening.Suchitemsmustnotbewashed

inthedishwasherunlesstheywilleasilypassthrough.

Donotallowforeignobjectstoentertheunit,especiallymetalliccontaminants.

– 8 –

Unloading

Removewarefromtheconveyor.Ifadishpushesagainstthedishlimit,theconveyor

stops and the pumps run for one minute before shutting off.

Unloadtheconveyorstartingwiththewarefurthestfromthedishlimit.Removethe

warethatisstrikingthedishlimitlast.Themachineautomaticallyrestarts.

RECOMMENDED MINIMUM TEMPERATURES

Thewatertemperaturesinthetanksandrinsearmsaremonitoredelectronically

andaredisplayedonthecontrolboxkeypaddisplay.Thedisplayshouldbechecked

periodicallytoassurethatpropertemperaturesarebeingmaintained.

NOTE: RefertotheHOTWATERSANITIZINGlabelonthesideofthecontrolbox

for minimum temperature ratings.

CONVEYOR SPEED ADJUSTMENT

Depending on the type of ware being washed, the conveyor speed can be adjusted

bypressingtheSPEEDSELECTIONkeylocatedonthekeypadonthefrontofthe

controlbox(Fig.16).Whenrstpressingthekey,thecurrentspeedselectionwill

beshownonthebottomlineofthedisplay.Bypressingthebuttonasecondorthird

time,thespeedwilltoggletothenextavailableselections;Speed:Low,Speed:

Medium, Speed: High.

CLEANING

ThedishwasherMUSTbethoroughlycleanedattheendofeachworkingshiftor

aftereachmeal.PushthePOWERbuttononthekeypadtoturnthemachineOFF.

Followtheinstructionsbelowforthemanualcleaningprocess.

Formachines equippedwithAuto Clean,seeinstructions on page9.TheAuto

Cleanprocesscanbecompletedattheendofeachworkingshiftoraftereachmeal;

however,itisrecommendedthatamanualcleaningbecompletedonceperday.

Disconnect the electrical power to the machine and follow

lockout/tagout procedures. There may be multiple circuits. Be sure all circuits

are disconnected.

Openallfrontaccessdoors.Drainthemachinebyswingingthetankdrainhandles

totheleftasshownonthelabelslocatedaboveeachtankdrain.Drainhandlesare

locatedneartheooratthefrontofeachtank.

Removeandcleanthecurtains.Beforeremovingthestrainerbasketsandpans,

cleantheinteriorandalltankshelvesusingahoseandspraynozzle.Flushall

debris toward the strainers.

– 9 –

Removethewasharmsbyliftinguponthearmclearingthetabfromthenotchin

thewasharmsupport.Slideupperarmsforward,swingingfrontofarmdown.Slide

lowerarmsforward,tiltfrontofarmsupwardtoallowwatertodrain.Removearms.

Cleanwasharmsinasink,openingwasharmsliderstoushfoodsoilfromarms.

Removethestrainerbasketsandstrainerpans.Alsoremovethedualrinsestrainer.

Empty strainers in trash receptacle or food waste disposer. DO NOT STRIKE

STRAINERPANSORSTRAINERBASKETSONSOLIDOBJECTTODISLODGE

DEBRIS. Scrub strainer pans and strainer baskets in a sink.

Removedualrinseandnalrinsearmsandcleandebrisfromnozzlesandarms.

Neverusesteelwooltocleanwarewashersurfaces.Useonlyproductsformulated

tobesafeonstainlesssteel.

Flushtankswithawaterhose,removinganyaccumulationoffoodsoil.

Reinstallallarmsintheirproperlocationandorientation.Ensurethatupperarm

nozzlespointdownward,andlowerarmnozzlespointupward.

Toinstallwasharms,slidemanifoldsonthesupportstowardtherearofthemachine

and ensure the tabs on the sides of the arms drop into the notches in the supports.

Replacethestrainerpansandstrainerbaskets.Reinstallthecurtainsaccordingto

thecurtainchartshownonpages14-15ofthismanual.Leavethemachinedoors

opentoallowtheinteriortoairoutanddry.

Cleanmachineexteriorlikeanyotherstainlesssteelappliance.Usedampcloth

andmildsoapywater.

Spraythechannelswherethesensorsarelocatedattheloadendofthemachine

(Fig.12).Donotattempttocleanthesewithmetallicobjectsasdamagetosensors

can occur.

Fig. 12

– 10 –

Deliming (Manual process for machines not equipped with Auto Delime)

For machines not equipped with Auto Delime, follow these steps for manually

delimingthemachine.

1. PowermachineOFF.

2. Drainalltanksandremoveallfoodsoilsbycleaningthescrapbasketsandstrainer

pans.Flushinteriorofmachinewithahose.

3. Disable the detergent feeder chemical system according to the chemical

manufacturer’srecommendation.Thiswillpreventtheadditionofdetergentduring

thedelimingoperation.

4. Closealltankdrainsandre-installthestrainerpansandscrapbaskets.

5. PowerthemachineONallowingittollwithfreshwater.

6. RefertothePROGRAMMINGsectionofthismanualandadjusttheAUTOTIMEOUT

timeto30minutesbyenteringtheMANAGERPROGRAMMING.Thiswillallowthe

unittorunfor30minutesforthedelimecyclewithoutshuttingoff.NotetheAUTO

TIMEOUT setting before adjusting to 30 minutes.

7. Oncethellcyclehascompleted,openthedoorsandpourtherequiredamountof

delimerineachtankaccordingtothechemicalmanufacturer’sinstructionsfollowing

theirrecommendationsforpersonalprotectiveequipment(PPE).

8. Closethedoorsandstartthemachineallowingthepumpstorunfor30minutesat

normaloperatingtemperatures.

9. Afterthe30minuteshaselapsedandthemachinehastimedout,openthedoors

andinspecttheinteriorforanyremaininglimescaleresidue.Iflimescaleremains,

closethedoorsandrunthemachineforalongerperiodoftime.Dependingonthe

timebetweendelimingcyclesandthewaterhardness,themachinemayneedto

runlongerand/oradjusttheamountofdelimerbeingused.

10. PowermachineOFFanddrainalltanks.

11. Thoroughlyspraytheinsideoftheunitushingtheremainingdelimersolutiondown

the drain.

12. ClosealltankdrainsandpowerthemachineONallowingittollwithfreshwater.

13. RefertothePROGRAMMINGsectionofthismanualandadjusttheAUTOTIMEOUT

timebacktotheoriginalsetting asnotedinStep6byenteringtheMANAGER

PROGRAMMING.

14. Oncethellcyclehascompleted,startthemachineandrunthepumpsforafew

minutestoushanyremainingdelimerfromthesystem.

15. PowermachineOFFanddrainalltanks.

16. Following the chemical manufacturer’s recommendation, enable the detergent

feederchemicalsystem.

17. Theunitisnowreadyfornormaloperation.

Certain areas of the machine,suchastheloading,nalrinse,andunloadingsections,

maystillshowsignsofscaleresidueastheseareasarenotsubjectedtotherecirculated

washcontainingthedelimingsolution.Theseareaswillneedtobecleaned/delimed

manually as instructed below. DO NOT spray or wipe the deliming solution on

exterior surfaces of the dish machine as this could cause corrosion. If delimer

solution is accidentally contacted with the exterior of the machine, ush with

water and wipe. Always wear proper personal protective equipment (PPE) when

using delimer following chemical manufacturer’s recommendations.

– 11 –

1. Followingthechemicalmanufacturer’sinstructions,prepareamixtureofdelimer

andwater,andpourorbrushthesolutionontothesurfacetobecleaned.

2. Allowtosoakfor10minutes.Ifrequired,scrubtoremoveheavydeposits.

3. Rinsethoroughlywithfreshwater.

Automatic Soil Removal Section (When Equipped)

MachinesequippedwithAutomaticSoilRemoval(ASR)featureanadditionalsection

locatedimmediatelyaftertheloadendofthemachine.Duringmachineoperation,

theASRsectioncapturesfoodsoilandpumpsittotheexternalscrapbasket,located

beneaththeloadofthemachine.

Toemptytheexternalscrapbasketduringmachineoperation,removethebasket,

emptyandreplace.ThemachinewillcontinuetooperateunlesstheSTOPbuttonis

pressedattheload,unloadoronthekeypadlocatedonthefrontofthecontrolbox.

TocleantheASRsystem,removetheexternalscrapbasketlocatedbeneaththe

loadsection,emptyfoodsoil,rinsebasketinsinkandreplace.Removetheupper

andlowerASRwasharms.Toremovetheupperarm,pullbackonthetab,allow

thearmtodropandpullout.Toremovethelowerarm,pullupslightlyandpullthe

armout.Rinsebotharmsinthesinkandensureallnozzlesareclearofdebris.

RemovetheASRstrainerpan,andthenremovethetwopiecesoilcollectorstand

pipe(Fig.13).Cleanthesecomponentsusingasprayerhoseinasink.Useahose

tospraydowntheinsideoftheASRsectionaswell.

Fig. 13

Replaceallcomponentswhencomplete.Toreplacethesoilcollectorstandpipe,drop

thebottomofthetubewiththestrainerintothedrainbodylocatedatthebottomof

theASRtankandtheninstallthesoilcollectortubeontopofthepreviouslyinstalled

tube.Placethestrainerpanontop,notingthatitsitsslightlyhigherthanthetank.

Replacethelowerwasharmbyfollowingtheguiderailandpushingthetubeinto

placeinthemanifold.Replacetheupperwasharmbypushingthetubeintothe

uppermanifold,pushingupandsnappingintoplace.

– 12 –

Auto Clean (When Equipped)

ToperformtheAuto Clean procedure,followthesteps listedbelow(italicstext

indicatesactualmachinedisplayprompts):

1. PresstheblueAutoCleanbuttonlocatedonthekeypadonthefrontofthe

controlbox.

2. Press ENTER to begin Auto Clean.

3. ThedisplaybrieyshowsPress Stop key at any time to abort Auto Clean cycle

before proceeding to step 4.

4. Close Master Drain–closethemanualMasterDrainvalvelocatedateitherthe

loadorunloadendofthemachine.

5. Open All Tank Drains–openalltankdrainslocatedatthebottomofeachtank.

6. Tanks draining. Please wait a few seconds – at this time, the machine is draining

thewaterinthetanksbelowthestrainerpansthrutheMasterDrainautomaticvalve.

7. Clean and replace strainer baskets. Open wash arm sliders, Close Doors, Press

Enter When Done –FormachinesequippedwithASR,cleanandreplacethe

soilcollectorstandpipeandstrainerpan.

8. No additional user intervention required. Auto clean will take approximately 30

minutes–atthistime,themachineisintheself-cleaningmode.Washpumpswill

runtoushfoodsoilfromwasharms,andthenAutoCleannozzleslocatedatthe

rearofeachchamberwillwasheachchambersectionabovethestrainerpans.

9. Close Wash Arm Sliders; then close all doors-Press Enter When Done

10. Open Master Drain–openthemanualMasterDrainvalvelocatedateitherthe

loadorunloadendofthemachine.

11. Close Tank Drains–closealltankdrainslocatedatthebottomofeachtank.

12. Auto Clean complete, Press Enter key to rell. Otherwise machine will shut

down in 60 seconds.

PressingtheSTOPbuttonatanytimeduringtheAutoCleanprocesscancelsthe

AutoCleancycle.ThedisplayreadsAuto Clean cycle not complete. Press STOP

to abort, ENTER to resume –AfterpressingSTOPtoabort,followtheonscreen

instructions to prepare for washing.

Auto Delime (When Equipped)

ToperformtheAutoDelimeprocedure,followthestepslistedbelow(italicstext

indicatesactualmachinedisplayprompts):

1. WhenthedisplaypromptsDelime Recommended,refertothe‘PROGRAMMING’

sectionofthismanualwhenreadytoinitiatethedelimecycle.Navigatetothe

‘Actions’menuandscrolldownto‘RunDelimeCycle’.PresstheENTERkey.

2. Thedisplaybrieyreads Press Stop key at any time to abort Delime cycle

before proceeding to step 3.

3. Remove ware from machine. Press ENTER when done or STOP to abort.

4. Place Delime Pump hose in delime solution. Press Enter when done.Placethe

hosefromthedelimechemicalpumplocatedattheunloadendofthemachine

intothedelimesolutioncontainer.

5. Open All Tank Drains-Leave drains open.–openalltankdrainslocatedatthe

bottom of each tank.

– 13 –

6. Clean Strainer Baskets, then replace. Press enter when done.

7. Tanks Draining Please Wait–afteralltankshavedrainedthedisplaytoggles

to step 8.

8. Close Master Drain–closetheMasterDrainmanualvalvelocatedateitherthe

loadorunloadendofthemachine.

9. Tanks Filling Please Wait–afterthemachinehaslledwithapproximately1-2

inchesofwaterinthetanks,thedisplaytogglestostep10.

10. Pour xx gallons delime into Tank 1. Press Enter when done–thedisplayprompts

youtopourtherequiredamountofdelimerintoTank1,locatednexttothedual

rinsetanktowardstheloadendofthemachineandlabeledDelime Tank.

11. Press ENTER to start conveyor.

12. Delime Cycle Running. Approximate Time Left: XX:XX – at this time, the machine

isrunningtheautodelimecycle.

13. Auto Delime Complete. Press Enter key to rell. Otherwise, machine will power

down in 5 minutes

14. Open Master Drain – after pressing Enter in the previous step or powering the

machinebackupfromapowerdown,opentheMasterDrainmanualvalve

locatedateithertheloadorunloadendofthemachine.

15. Close all Tank Drains–closealltankdrainslocatedatthebottomofeachtank.

PressingtheSTOPbuttonatanytimeduringtheAutoDelimeprocesswillcancel

thecycle.Ifthedelimesolutionhasnotyetbeenintroducedintothesystem,the

displaywillreadTanks rinsed and ready for wash. Press Enter to rell. Or machine

will power down in 5 minutes.Ifthedelimesolutionhasbeenintroducedintothe

system,thedisplaywillreadDelime solution in Tanks. Press Enter key to drain and

rinse tanks. Press Stop key to skip rinse cycle.

DO'S AND DON'TS FOR YOUR NEW HOBART DISHWASHER

DO assure proper water hardness of 3 grains or less per gallon.

DO pre-scrap dishes thoroughly.

DO use only detergents recommended by your chemical professional.

DO, at the end of the day, complete a manual cleaning cycle as needed; thoroughly cleanse

the machine, rinse, and dry (leave doors open).

DO, at the end of each meal period, complete an Auto Clean cycle (when equipped), following

instructions on the display.

DO use only products formulated to be safe on stainless steel.

DO NOT use detergents formulated for residential dishwashers.

DO NOT allow food soil to accumulate on the tank bottom.

DO NOT use steel wool to clean ware or dishwasher surface.

DO NOT allow foreign objects to enter the unit, especially metallic contaminants.

NOTE: Failuretofollowuse,care,andmaintenanceinstructionsmayvoidyourHobartdishwasher

warranty.

– 14 –

CURTAINS: MODELS FT1000, FT1000-ER, FT1000-ER-BD, & FT1000-ADV

Fig. 14

– 15 –

CURTAINS: MODELS FT1000S, FT1000S-ER, & FT1000S-ER-BD

Fig. 15

– 16 –

PROGRAMMING

MACHINE OPERATION AND PROGRAMMING SECURITY LEVELS

The advanced digital controls on your dishwasher allow several setup and

customizationoptions.Becausetheseoptionscanaffecttheoperationofthemachine,

theyarealllocked-outbydefaultfromthefactory.Tounlockthemforediting,the

securitylevelmustbeelevatedtoanappropriatelevel.

Itisrecommendedtokeepthedishwasherinthelowestsecuritylevelpossibleat

alltimes.Thiswillpreventoptionsfrombeinginadvertentlyorintentionallymodied

fromwhatisexpectedoracceptable.Thesecuritylevelwillautomaticallyrevert

backtothelowestallowablelevel(eitherOperatororSuperOperator,asdescribed

below)whenanyofthefollowingoccur:

1. No keys on the keypad are pressed for 10 minutes or more.

2. ThemachineisplacedinStandbybypressingthePOWERkey.

3. AninvalidSecurityCodeisenteredontheENTERSECURITYCODE?Screen.

Thefollowingnamesanddescriptionsofthevarioussecuritylevelsarelistedfrom

thelowestleveltothehighestlevel.Ahighersecuritylevelincludesalloftheabilities

ofthelowerlevelsplussomeextraabilities,asdescribedbelow.

NOTE: Thesecurityleveldoesnot,byitself,affecttheoperationofthemachineor

inhibittheuseofanyoftheStart,Stop,orPowerkeysorbuttons.Allofthesebasic

functionsarealwaysavailableinanysecuritylevel.

Operator – O

Thisisthemostbasicsecuritylevelandisenabledbydefaultwhentheunitis

poweredupasinitiallysetbythefactory.Nosecuritycodeisrequiredtoenterthis

securitylevel.ThislevelonlyallowsenteringtheSecurityCodetoelevatethecurrent

securityleveltosomethinghigher.

SuperOperator – SO

ThissecuritylevelcanbeenabledviatheManagerMenu(Manager→Operation

Parameters→SuperOperatorAccess).Onceenabled,"SuperOperator"willbe

addedasanoptionwhentheMenubuttonispressed(inthe"MainMenu").Asecurity

codeisNOTrequiredtoentertheSuperOperatormenuonceithasbeenenabled.

TheSuperOperatormenuallowssomeadvancedfeaturestobeaccessed;suchas

initiatingAutoDelime,reviewingerrorlogs,andchangingthedisplayedlanguage.

AdetailedlistofSuperOperatorfunctionsisshownintheParametersMenu.

– 17 –

Manager – M

Thissecuritylevelisthehighestlevelattainablebytheuser.ItrequirestheManager

CodetobeenteredbeforethesecuritylevelwillbeelevatedtoManager.

ThissecurityleveloffersunrestrictedaccesstoalloftheoptionslistedintheParameters

Menu.Becauseofthis,itisrecommendedthatpowertothemachinebecycledoff

andonwhenaccesstotheManagerleveloptionsarenolongerexplicitlyneeded.

TheSecurityCodefortheManagerlevelcanbechangedbyakitchenmanager

oranyonewiththeManagerCode.Thedefaultcodeislistedinthesectiontitled

Entering the Operation Parameters Menu. As such, it is recommended that this code

bechangedfromthedefaultandstoredinasafeplacewhereallkitchenmanagers,

butnooneelse,canaccessit.Ifthecodeiseverlostorforgotten,itcanbereset

by Hobart Service.

NOTE: Having Hobart Service reset the Manager Code is not covered under either

the basic or the extended warranty.

USER PROGRAMMING INSTRUCTIONS

Thedishwasherisequippedwithelectronicdigitalcontrolstoallowgreaterprecision

forcleaningyourware,maintainingrequiredtanktemperaturesandotheradvanced

functions.Someofthesefunctionsarecustomizedtosuittheneedsofyourkitchen

operation.

Allcustomizationisperformedthroughtheon-screenmenuusingtheUP,DOWN/

MENU,ENTER,andSTOP/BACKkeyslocatedonthekeypadonthecontrolbox

door(Fig.16).

START

STOP or BACK

POWER

AUTO CLEANSPEED

SELECTION

DOWN or

MENU

UPENTER DISPLAY

Fig. 16

– 18 –

MENU DISPLAY PROMPTS

Thefollowingpromptsareusedinsidethemenus.

• TheUPandDOWNarrowkeysareusedtochangeparametervaluesandto

navigate the menu.

• TheENTERkeyisusedtoacceptavalue,performaspeciedactionorenter

a submenu.

• TheBACKkeywillalwaysrevertbacktothepreviousmenuscreen.

• Thetextjusttotherightofthe‘>’symbolonthedisplayscreenshowswhat

actionorcommandwilloccurbypressingtheENTERkey.

ENTERING THE MANAGER MENU

To enter the Manager menu:

1. PresstheMENUkeyfromthemainscreen.ThiswilltakeyoutotheMain Menu.

2. Withthe‘>’symboltotheleftofManager,presstheENTERkey.Thiswilltake

you to the Enter Security Code screen.

3. You are prompted with four asterisks [****].

4. UsetheUPandDOWNkeystochangethedigitoftheSecurityCodetothe

appropriatevalue*.

*ThedefaultSecurityCodetoenterManagerprogrammingis1001.Thiscodecan

bechangedbyanyonewiththisknowledgeanditisrecommendedtochangeitfrom

thedefault.Ifthecodeiseverlostforsomereason,itcanberesetbyHobartService.

NOTE: Resetting the code is not covered under your warranty, whether you are in

theinitialwarrantyperiodorintheextendedwarrantyperiod.

5. Press the ENTER key to move to the next digit to the right.

6. Repeat steps 4 and 5 for each digit.

AfterpressingENTERonthefourthdigit,youwillbeintheManager Menu.

7. PresstheUPorDOWNkeysrepeatedlyuntilthe‘>’symbolistotheleftofthe

desired option and then press the ENTER key. The Manager options are: About,

Actions, Logs, and Operation Parameters.

ABOUT SCREEN

TheAboutscreendisplaysthefollowinginformation;Machine Model, Control Board

Revision, Relay Board Revision, Software Version, Sanitizing Mode, and Service

Number.

– 19 –

ACTIONS MENU

TheActionsMenuprovidesthefollowingoptions:

• ChangeManagerCode:Allowsthemanagersecuritycodetobechangedfrom

thedefaultvalue.

• ReverseJog:Allowstheconveyortobejoggedinthereversedirectionincase

thereisaconveyorjam.Whenenteringthismode,thefollowingmessageis

displayed:

Be sure all personnel clear of conveyor. Press button in upper Control Box

while pressing Enter.

> Exit without jogging

Reverse jog conveyor

Toreversejogtheconveyor,presstheENTERbuttonwiththe‘>’symbollocated

totheleftofReversejogconveyorwhilealsopressingthegreenbuttonlocated

behindtheuppercontrolboxdoor(Fig.17).

REVERSE JOG BUTTON

Fig. 17

• Run Delime Cycle:InitiatestheAutoDelimecycle;seepage10ofthismanual

forthecompleteprocedure.

• Set Date/Time: Enter this screen to set the date and time

LOGS MENU

TheLogsmenuprovidesthefollowingoptions:

• Delime Counter:Displaysthetimeremainingbeforedelimerecommendation

isdisplayed.AlsoallowstheabilitytoClear Delime Counter.

• Error Log: Displaystheprevious errorsalongwith thedate/timethe errors

occurred.

• Statistics:EnteringtheStatisticsscreenwilldisplaythefollowinginformation;

Time of Operation, Run Time Percent, Rinse Time, and Fill Time.

– 20 –

OPERATION PARAMETERS MENU

NOTE: Theparameterscanbechangedanytimethedisplayisactive,whichis

whenthemachineisoperatingorinidlemode.

Hobartbelievesthatthedefaultsettingsthatleavethefactoryaresuitableforthe

majority of kitchen operations. However, there are cases where kitchen managers

mayndtheneedtochangeoneormoreoptions;theParametersMenuallows

these changes.

WithintheParametersMenu,themanager(oroperator,insomecases)maymodify

factorydefault settings.The menustructureand descriptionofeach optionare

detailedbelow.PleasecontactHobartServiceifyouareuncomfortablechanging

anysettingorareunsureofwhichone(s)tochange.

TheParametersMenuliststheparametername,ashortdescription,alistofpossible

valuestheparametercanhave,thefactorydefaultvalue based onthe specic

dishwashermodel,andthesecuritylevelrequiredtoaccessthatparameter

PARAMETERS MENU

Parameter Name Description Possible Values

Default

Value

Security

Required

AutoCleanDemoMode EnablesordisablestheAutoClean

DemoMode.Whenenabled,this

modeallowstheAutoCleancycle

to be demonstrated for training

purposes without running the

completecycle.

Disabled

Enabled

Disabled M

Auto Timeout Adjustabletimerfordetermining

when to shut down the pumps and

conveyor when no dishes are in the

machine.

1 – 30 mins 6 mins SO

Conveyor Speed High Sets the High conveyor speed

setting when the operator presses

theSpeedSelectionbuttononthe

keypad changing the setting to

Speed: High.

4.0-8.5 8.5ft/min M

Conveyor Speed Low Sets the Low conveyor speed

setting when the operator presses

theSpeedSelectionbuttononthe

keypad changing the setting to

Speed: Low.

4.0-8.5 4.0ft/min M

Conveyor Speed Medium Sets the Medium conveyor speed

setting when the operator presses

theSpeedSelectionbuttononthe

keypad changing the setting to

Speed: Medium.

4.0-8.5 6.3ft/min M

Delime–MainTanks

Quantity

Setsthenumberofdelimergallons

requiredpertank.

0.0 – 2.0 0.50 M

La page charge ...

Hobart FT1000S-ER Mode d'emploi

Ce manuel convient également à

Hobart FT1000S-ER Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents