Haier HI50IB Installation and User Manual

Installation and User Manual

Instructions d’installation et

Guide de l’utilisateur

Instrucciones de instalación y

Manual del usuario

HI50IB

Automatic Undercounter Ice Machine

Machine à glaçons automatique sous plan

de travail

Máquina de Hielo Automatic Para Debajo

de la Encimera

49-60811 01-18 GEA

49-60811

2

3

49-60811

TABLE OF CONTENTS

ENGLISH

ICE MACHINE SAFETY ......................................................4

PARTS AND FEATURES ......................................................6

INSTALLATION REQUIREMENTS .............................................7

Location Requirements .....................................................7

Installation Clearances ......................................................8

Water Supply Requirements .................................................8

Connecting Electricity ...................................................... 9

INSTALLATION INSTRUCTIONS ............................................10

Unpacking .................................................................10

Reversing the Door Swing (Optional) ........................................10

Connect the Water ........................................................ 11

Connect the Electrical Supply ..............................................14

Install the Ice Machine ......................................................14

Leveling the Ice Machine ...................................................15

ICE MACHINE USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Operation .................................................................16

Ice Making Cycles ..........................................................17

Controls. ..................................................................18

ICE MACHINE CARE .......................................................20

Cleaning ...................................................................20

Vacation and Moving .......................................................24

Reinstalling/Using Ice Machine Again .......................................24

TROUBLESHOOTING ...................................................... 25

LIMITED WARRANTY ......................................................27

RECORD KEEPING ........................................................28

49-60811

4

ENGLISH

Ŷ Use this appliance only for its intended purpose as described in this

user manual.

Ŷ This appliance must be properly installed in accordance with the

installation instructions before it is used. See grounding instructions in

the installation section.

Ŷ Plug into a grounded 3 prong outlet.

Ŷ Do not remove ground prong.

Ŷ Do not use an adapter or extension cord.

Ŷ Do not repair or replace any part of the appliance unless specifically

recommended in the manual. All other servicing should be referred to a

qualified technician.

Ŷ Disconnect power before servicing.

Ŷ Replace all parts and panels before operating.

Ŷ Use nonflammable cleaner.

Ŷ Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

Ŷ Do not store explosive substances such as aerosol cans with a

flammable propellant in this appliance.

Ŷ Before discarding or removing from service, remove the door. This will

reduce the possibility of danger to children.

Ŷ To avoid serious injury or death, children should not stand on, or play in

or with the appliance.

Ŷ Children and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge can use this appliance

only if they are supervised or have been given instructions on safe use

and understand the hazards involved.

Ŷ This appliance is intended to be used in household and similar

applications such as: staff kitchen areas in shops, offices and other

working environments; farm houses; by clients in hotels, motels, bed

& breakfast and other residential environments; catering and similar

non-retail applications.

ICE MACHINE SAFETY

CAUTION

To reduce the risk of injury when using your ice machine,

follow these basic safety precautions.

Ŷ Keep fingers out of the “pinch point” areas; clearances between the

door and cabinet are necessarily small. Be careful closing door when

children are in the area.

Ŷ Do not touch the cold surfaces in the ice machine when hands are damp or

wet, skin may stick to these extremely cold surfaces.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of fire, explosion, electrical shock,

injury to persons, or damage when using the ice

machine, follow basic precautions, including the following:

5

49-60811

ENGLISH

STATE OF CALIFORNIA PROPOSITION 65 WARNINGS:

WARNING

This product contains one or more chemicals known to

the State of California to cause cancer and birth defects or other

reproductive harm.

ICE MACHINE SAFETY

PROPER DISPOSAL OF YOUR OLD APPLIANCE

WARNING

SUFFOCATION AND ENTRAPMENT HAZARD

Failure to follow these disposal instructions can result in death or

serious injury.

IMPORTANT: Child entrapment and suffocation are not problems of the

past. Junked or abandoned appliances are still dangerous even if they

will sit for “just a few days.” If you are getting rid of your old appliance,

please follow the instructions below to help prevent accidents.

Before You Throw Away Your Old Appliance:

Ŷ Take off the door.

Ŷ Leave the shelves in place so that children may not easily climb inside.

Refrigerant and Foam Disposal:

Dispose of appliance in accordance with Federal and Local Regulations.

Flammable insulation material used requires special disposal

procedures. Contact your local authorities for the environmentally safe

disposal of your appliance.

READ AND SAVE THESE INSTRUCTIONS

49-60811

6

ENGLISH

PARTS AND FEATURES

A. Door

B. Water Distribution Tube

C. Evaporator (ice mold)

D. Water Trough

E. Float

F. Ice Bucket

G. Control Panel

H. Front Louver Panel

I. Feet (not shown)

J. Water Supply Hose

K. Power Cord

L. Water Inlet

M. Drain Outlet

N. Ice Scoop

O. Drain Hose

P. Drain Hose Clamp

A

J

K

L

M

N

O

P

B

C

F

H

G

I

D

E

7

49-60811

ENGLISH

INSTALLATION REQUIREMENTS

LOCATION REQUIREMENTS

To ensure proper ventilation for your ice machine, the front of the unit must

be completely unobstructed.

When installing the ice machine under a counter, follow the recommended

spacing dimensions shown in the “Installation Clearances” section. Allow

at least 3-7/8” (9.8 cm) clearance at rear, and 3/8” (1.0 cm) at top and 3/16”

(0.5 cm) at sides for proper air circulation.

The installation should allow the ice machine to be pulled forward for

servicing, if necessary.

Choose a well ventilated area with normal operating temperatures above

50°F (10°C) and below 100°F (38°C). Normal operating water temperature

should be between 41°F (5°C) and 90°F (32°C). Operation of the ice machine

for extended periods outside of these normal temperature ranges may

affect production capacity.

The ice machine should not be located next to ovens, grills or other high

heat sources.

The ice machine MUST be installed in an area protected from the elements,

such as wind, rain, water spray or drips.

The ice machine should be located on a firm and level surface. It is

important for the ice machine to be leveled in order to work properly. If

needed, you can adjust the height of the ice machine by turning the feet.

See the “Leveling the Ice machine” section.

• Do not install the ice machine where the temperature will go below

50°F (10°C) because it will not run often enough to maintain proper

temperatures.

• Do not install the ice machine where the temperature will go above

100°F (38°C) because it will not perform properly.

• Install it on a floor strong enough to support it fully loaded.

• Do not install the ice machine in a location exposed to water (rain,

etc.) or direct sunlight.

WARNING

Explosion and Fire Hazard

Keep flammable materials and vapors, such as gasoline, away from

appliance.

Failure to do so can result in death, explosion or fire.

49-60811

8

INSTALLATION REQUIREMENTS

ENGLISH

INSTALLATION CLEARANCES

Top View

Side View

Rear of Unit

Front of Unit

Top of Unit

Front

Edge

Side Side

q (0.953 cm)

A\5:

(0.48 cm)

A\5:

(0.48 cm)

#s¤)($æð¥

WATER SUPPLY REQUIREMENTS

Installation of the ice machine requires a cold water supply inlet of ¼”

¤&#%ðð¥öòé÷æòóóèõ÷øåìñêúì÷ëäöëø÷¡òģùäïùè

The ice machine requires a continuous water supply with a minimum

pressure of 15 psig (103 KPa) and a static pressure not to exceed 80 psig

(552 kPa). The temperature of the water feeding into the ice machine should

be between 41°F (5°C) and 90°F (32°C) for proper operation.

Ò÷ìöö÷õòñêïüõèæòððèñçèç÷ëä÷äúä÷èõĤï÷èõåèøöèçÊĤï÷èõìéì÷ìöòé÷ëè

proper type, can remove taste and odors as well as particles. Some water is

very hard, and softened water may result in white, mushy cubes that stick

together. Deionized water is not recommended.

WARNING

Connect to potable water supply only.

9

49-60811

INSTALLATION REQUIREMENTS

ENGLISH

Do not, under any circumstances, cut or remove the third (ground)

prong from the power cord. For personal safety, this appliance must

be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding)

plug which mates with a standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make

sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it is your personal

responsibility and obligation to have it replaced with a properly grounded

3-prong wall outlet.

The ice machine should always be plugged into its own individual

electrical outlet which has a voltage rating that matches the rating plate.

A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded electrical supply

is required. This provides the best performance and also prevents

overloading house wiring circuits which could cause a fire hazard from

overheated wires.

Never unplug your ice machine by pulling on the power cord. Always grip

plug firmly and pull straight out from the outlet.

Immediately discontinue use of a damaged supply cord. If the supply

cord is damaged, it must be replaced by a qualified service professional

with an authorized service part from the manufacturer.

When moving the ice machine away from the wall, be careful not to roll

over or damage the power cord.

The ice machine must be installed with electrical and water connections

in accordance with all state and local codes.

A wall outlet directly behind the ice machine will make installation easier.

CONNECTING ELECTRICITY

WARNING

ELECTRICAL SHOCK HAZARD

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical

shock.

49-60811

10

INSTALLATION INSTRUCTIONS

ENGLISH

REVERSING THE DOOR SWING (Optional)

UNPACKING

1. Remove packaging materials.

IMPORTANT: Do not remove any permanent instruction labels or the data

label on your ice machine.

2. Remove tape and glue from your ice machine before using.

• To remove any remaining tape or glue, rub the area briskly with your

thumb. Tape or glue residue can also be easily removed by rubbing a

small amount of liquid dish soap over the adhesive with your fingers.

Wipe with warm water and dry.

• Do not use sharp instruments, rubbing alcohol, flammable fluids, or

abrasive cleaners to remove tape or glue. These products can damage

the surface of your ice machine.

3. After you remove all of the packaging materials, clean the inside of your

ice machine before using it. See “Cleaning.”

4. Properly dispose of/recycle all packing material.

Tools Needed:

• Flathead Screwdriver • Phillips Screwdriver

To remove the door:

1. Unplug the ice machine or disconnect power.

2. Using a flathead screwdriver, remove the hinge pin from Hinge 1, and set

it aside.

3. Open the door about 20°, and then lift the door off Hinge 2, and set the

door aside.

WARNING

Excessive Weight Hazard

Use two or more people to move and install ice machine.

Failure to do so can result in death or personal injury.

Hinge Pin

Door

Cabinet

Hinge 1

Hinge 2

WARNING

Follow all steps when reversing the door swing. Failure

to follow these instructions, leaving off parts, or overtightening screws,

can lead to the door falling off and result in injury and property damage.

11

49-60811

To reverse the door:

1. Using a flathead screwdriver, remove the covers from the screw holes on

the side opposite the door hinges, top and bottom. Set aside.

2. Replace the hinge pin on Hinge 1 and tighten it firmly.

3. Remove the screws fastening Hinge 1 to the

cabinet and reinstall it on the opposite side of

the cabinet at the bottom.

4. Remove the screws fastening Hinge 2 to the

cabinet and reinstall it on the opposite side of

the cabinet at the top.

5. Using a flathead screwdriver, remove the hinge

pin from Hinge 2, and set it aside.

6. Rotate the door so that the handle is opposite

the hinge side and set the door onto the

bottom hinge pin.

7. Completely tighten the bottom hinge.

8. Insert the hole covers into the holes where the

screw were originally located.

ENGLISH

INSTALLATION INSTRUCTIONS

REVERSING THE DOOR SWING (Optional) (Cont.)

Hinge 2

Hinge 1

CONNECT THE WATER

The water supply should be ready at the point of installation. The water

supply pressure should be a minimum of 15 psig (103 KPa) with a static

pressure not more than 80 psig (552 KPa). (A wall outlet directly behind the

ice machine w3ill make installation easier.)

IMPORTANT:

• All installations must be in accordance with local plumbing code

requirements. Professional installation is recommended.

• Make certain the hoses are not pinched or kinked or damaged during

installation.

• Check for leaks after connection.

WARNING

Follow all steps when reversing the door swing. Failure

to follow these instructions, leaving off parts, or overtightening screws,

can lead to the door falling off and result in injury and property damage.

WARNING

Connect to potable water supply only.

49-60811

12

INSTALLATION INSTRUCTIONS

ENGLISH

Tools Needed:

• ½” Open-end Wrench

• Phillips Screwdriver

• Adjustable Pliers

CONNECT THE WATER LINE

1. Turn off the main water supply. Turn on the nearest faucet long enough to

clear line of water.

2. Find a ½” to ¾” vertical cold water pipe near the installation location. The

water supply hose is provided with the ice machine.

3. A shut-off valve must be installed to the main water supply. If the water

pipe has a plain piece of copper tubing, attach a ¼” outside diameter

(O.D.) compression union to the tubing and remove the nut.

4. Connect the nut from the water supply hose to the tap, and connect the

other end to the water inlet. Tighten firmly by hand, and then using a

wrench tighten an additional half turn.

5. Turn on main water supply and tap.

6. Check for water supply connection leaks. Tighten every connection

(including connection at the water inlet).

IMPORTANT: When you connect the water supply hose and the drain hose,

note the “Water inlet” and “Drain outlet” marked on the ice machine.

CONNECT THE DRAIN

You must connect the drain line before using the ice machine.

NOTE: If there is a drain line near the ice machine, the best choice is to drain

water to the drain line through the drain water hose provided with the ice

machine.

1. Locate the floor drain near the ice machine. The distance should be less

than 5 feet since the length of the long drain water hose provided with

the ice machine is about 5 feet.

2. Find the drain outlet on the back of ice machine. Connect the drain hose

to the ice machine drain outlet, tighten drain hose clamp, and insert the

other end of the hose into the drain line.

CONNECT THE WATER (Cont.)

13

49-60811

ENGLISH

INSTALLATION INSTRUCTIONS

CONNECT THE WATER (Cont.)

NOTE: Do not allow the drain hose to hang or loop higher than the floor

of the ice storage bin.

• All horizontal runs of drain lines must have a fall of ¼” per foot. An

air gap will likely be required between the ice machine drain hose and

the drain/waste receptacle. A standpipe with a trap below it would be

acceptable for the drain/waste receptacle.

• If a floor or other gravity drain below the level of the ice machine drain

outlet is not available, the use of an aftermarket sealed ice machine

drain pump kit will be required.

NOTES:

• Connect drain pump to your plumbing drain in accordance with all

state and local codes and ordinances.

• Drain pump must be a sealed design to prevent water overflow

during power outages.

• Minimum rated pumping rate of drain pump should be 0.5 gal./

minute (1.9 L/minute).

• Follow all installation instructions, provided with the drain pump kit.

• Drain pump should be located on a surface that is at the same level

as the surface underneath the ice machine. The top of the drain

pump reservoir must be no higher than the floor of the ice machine

storage bin.

• Do not allow the hose from the ice machine to the drain pump to

hang or loop higher than the floor of the ice storage bin.

• The end of the drain pump vent hose should be within 8” (20 cm) of

the top of the ice machine.

• Plumbing drain should be no more than 10 ft (3 m) above the outlet

of the drain pump.

• Do not connect the outlet hose of the drain pump to a closed pipe

system to keep drain water from backing up into the ice machine.

3. Pour 1 gallon of water into the ice storage bin to check for leaks in the

drainage system. Tighten any connections that leak.

49-60811

14

INSTALLATION INSTRUCTIONS

ENGLISH

INSTALL THE ICE MACHINE

This ice machine can be installed, as Free-Standing, or be Enclosed (as

under the counter top), or Built-in (sealed to the floor). In any case, there

must be adequate air space around the unit for ventilation. See “Installation

Clearances” in the “Location Requirements” section.

FREE-STANDING INSTALLATION

This ice machine may be installed in any location provided there is access

to an electrical supply, water supply and drain. You must follow the stated

instructions for Electrical Requirements, Water supply and proper drainage,

and Leveling the ice machine.

ENCLOSED INSTALLATION

An enclosed installation will allow you to install the ice machine under a

counter top or in a kitchen cabinet provided the required clearance space

around the ice machine is respected. See “Location Requirements.” This

installation has the same requirements as a free-standing installation.

Ŷ Plug into a grounded 3 prong outlet.

CONNECT THE ELECTRICAL SUPPLY

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove the ground prong from the power cord plug.

Do not use an adapter.

Do not use an extension cord.

Failure to do so can result in death, fire or electrical shock.

15

49-60811

ENGLISH

INSTALLATION INSTRUCTIONS

INSTALL THE ICE MACHINE (Cont.)

BUILT-IN INSTALLATION

If this method of installation is chosen, it will still be necessary to allow

adequate ventilation space around the ice machine.

1. Place ice machine in front of installation location. Place the ice machine

flat on the floor or on a platform depending on your installation

requirements.

2. The water supply line must be plumbed before connecting to the ice

machine.

3. Turn on main water supply and tap.

4. Check for water supply connection leaks. Tighten every connection

(including connection at the water inlet).

5. Suitable drain line must be connected for this installation.

6. If the electrical outlet for the ice machine is within the cabinet opening,

plug in the ice machine.

7. Push the ice machine into position.

IMPORTANT: Be sure to check that water supply and drain hoses cannot

get pinched or kinked or damaged before ice machine moves into its final

position.

LEVELING THE ICE MACHINE

The rolling casters on the bottom of the ice machine allow it to be moved

easily to clean and sanitize the floor underneath.

The ice machine must be level to work properly. If the ice machine is not

level the water will not flow properly through the evaporator (ice mold). The

ice production will be less than normal, and may be noisy.

The ice machine can be raised or lowered by rotating the plastic feet around

each of the four rolling casters on the bottom of the ice machine.

If you find that the surface is not level, rotate the feet until the ice machine

becomes level. You may need to make several adjustments to level it.

Place a carpenter’s level on top of the ice machine to see if the ice machine

is level from front to back and side to side.

Adjust the height of the casters as follows:

To Lower - Turn the leveling feet to the right.

To Raise - Turn the leveling feet to the left.

IMPORTANT: When the ice machine is ready to be installed in a cabinet or

directly on the floor, you must lock the casters after leveling. If the floor is

level, just turn the two front feet to touch the floor.

49-60811

16

OPERATION

1. The operating procedure is completely automatic.

2. When the ice storage bin is full of ice cubes, the machine stops making ice

automatically. It starts making ice again after ice cubes are removed.

3. The different colors of the LED display indicate various work modes.

4. A sensitive probe and accurate timer enhance the performance of the ice

machine.

5. A compressor protection system is built in.

HOW THE ICE MACHINE USES THE WATER

The ice machine begins with a fixed charge of water that is contained in the

water trough. As the water flows to the freezing evaporator surface, the

portion of water that does not contain mineral impurities freezes and sticks

to the ice cube molds. The water containing impurities falls back into the

water trough. During the ice making process, fresh water enters into the

water trough continuously as the water in the trough freezes continuously

in the evaporator.

ENGLISH

ICE MACHINE USE

A. Water Inlet

B. Water Distribution

Tube

C. Evaporator

D. Water Pump

E. Compressor

F. Condenser

G. Fan Motor

H. Hot Gas Valve

A

B

C

D

E

F

H

G

17

49-60811

ENGLISH

ICE MACHINE USE

OPERATION (Cont.)

1. Turn on the water tap, let the water trough fill.

2. Press the ON/ OFF button on the control panel. The ice machine will start

working automatically.

3. After 3 minutes, the machine will automatically go to the ice-making

stage, and the sound of water flowing will be heard.

4. When the batch of ice has been fully formed, ice will automatically be

harvested to the ice storage bin.

5. When the ice storage bin is full, the sheet of cubes will not fall completely

and will hold the bin-full probe open. The machine stops making ice

automatically.

6. The unit will start making ice again after the ice cubes are removed. Then

the bin-full probe swings back to operating position.

IMPORTANT:

• Although the ice machine has been tested and cleaned at the factory,

due to longterm transit and storage, discard the first few batches of ice

produced.

• Do not turn the water supply tap off when the ice machine is working.

• Do not touch evaporator when unit is running!

• Except to take ice from the unit, keep the door closed to reduce melting

and insure proper ice formation.

ICE MAKING CYCLES

There are two distinct cycles: Ice Freeze and Harvest. The freeze cycle

happens when water flows to the evaporator surface. The harvest cycle is

when the ice is released and water enters the machine. A complete cycle

takes about 20 minutes, but it depends on temperature and operating

conditions.

Ice Freeze Cycle

During the freeze cycle the compressor is pumping refrigerant, the fan

motor is blowing air, and the water pump is circulating water. When the

batch of ice has been fully formed, the ice machine stops the freeze cycle

and the harvest cycle begins.

Harvest Cycle

During the harvest cycle the compressor is still operating, but the water

pump has stopped. The hot gas valve opens, diverting hot refrigerant gas

into the evaporator. The hot refrigerant gas warms the evaporator, causing

the cubes to slide as a unit off the evaporator and into the storage bin. The

freeze cycle will restart when all the cubes have been harvested.

49-60811

18

CONTROLS

Bin Full (Red) LED indicator light

When Bin Full is lit, the ice storage bin is full of ice or something is blocking

the bin-full probe. The ice machine will stop working. When ice cubes are

removed from the ice storage bin, freeing the bin-full probe, the red LED will

flash for 3 minutes, and then the ice machine will restart and return to the

ice making mode.

Ice Making (Green) LED indicator light

When Ice Making is lit, the unit is working in the ice making mode controlled

by a temperature probe on the evaporator. When the green LED flashes, the

unit is working in the ice making mode controlled by a fixed timer.

Ice Harvest (Yellow) LED indicator light

When this is lit, the unit is working in the ice harvest mode controlled by the

ice-full probe.

Mode button: Mainly for Service

The MODE button is used to change between the Ice Making Mode and Ice

Harvest Mode. The operating mode can be determined from the status of

the green (Ice Making), and yellow (Ice Harvest) LEDs.

Press and release the MODE button to force the ice machine to switch from

the current state.

Adjust button

When this is pressed and held for longer than 3 seconds, the unit will enter

the Ice Size Adjustment mode. The mode can be judged from the status of

the yellow LEDs.

To adjust the ice size:

The ADJUST button is used to enter the Ice Size Adjustment mode. The

HARVEST LED must be lit solid before attempting to adjust ice size. Press

and hold the ADJUST button until the yellow HARVEST LED begins blinking.

This usually occurs after 3 seconds. Once the yellow LED starts to blink,

release the button. The yellow LED blinks continuously while in the Ice Size

Adjustment mode.

ICE MACHINE USE

ENGLISH

ICE

ON/OFF CLEAN ADJUST MODE

BIN FULLHARVEST

19

49-60811

ICE MACHINE USE

ENGLISH

CONTROLS (Cont.)

To decrease the cube size, press the CLEAN button. The ICE green LED

lamp will blink momentarily each time the CLEAN button is pressed. The

green LED will remain illuminated when the smallest size cube is achieved.

To increase the cube size, press the MODE button. The BIN FULL red LED

lamp will blink momentarily each time the MODE button is pressed. The red

LED will remain illuminated when the largest size cube is achieved.

NOTES:

• When adjusting the ice cube size, if the ICE, HARVEST and BIN FULL LEDs

all start blinking at the same time, this indicates that the ice cube size is

set to medium. Medium is the original factory setting.

• Ice Size Adjustment mode cannot be entered if the ice machine is in the

Clean or Bin Full mode.

• After 10 seconds without any operation, the ice machine will return to the

previous mode.

49-60811

20

ENGLISH

ICE MACHINE CARE

CLEANING

IMPORTANT: If the ice machine is left unused for a long time, before the

next use it must be thoroughly cleaned. Follow carefully any instructions

provided for cleaning or use of sanitizing solutions. Do not leave any

solution inside the ice machine after cleaning.

• Periodic cleaning and proper maintenance will ensure efficiency, top

performance, and long life. The maintenance intervals listed are based on

normal conditions. You may want to shorten the intervals if you have pets,

or there are other special considerations.

• Do not place or store any items other than ice in the ice storage bin. Wine

and beer bottles are not only unsanitary, but the labels may slip off and

plug up the drain.

EXTERIOR CLEANING

Painted metal: Wash painted metal exteriors with a clean, soft cloth or

sponge and a mild detergent in warm water. Rinse surfaces with clean,

warm water and dry immediately to avoid water spots. Do not use abrasive

cleaners on enamel surfaces as they may scratch the finish.

Stainless steel: Stainless steel is corrosion resistant and not corrosion-

proof. To help avoid corrosion of your stainless steel, wash stainless steel

surfaces with a clean, soft cloth or sponge and a mild detergent in warm

water. Rinse surfaces with clean, warm water and dry immediately to avoid

water spots. Do not use abrasive or harsh cleaners. Do not use chlorine

bleach on stainless steel surfaces.

NOTE: When cleaning stainless steel, always wipe in the direction of the

grain to avoid cross-grain scratching.

WARNING

Electrical Shock Hazard

Unplug your appliance or disconnect power before cleaning.

Failure to do so can result in death, electric shock or personal injury.

La page charge ...

Haier HI50IB Installation and User Manual

Haier HI50IB Installation and User Manual

dans d''autres langues

Autres documents