Proline PCI300G-E-2 Mode d'emploi

BUILT-IN

FRIDGE FREEZER

Instruction booklet

COMBINÉ ENCASTRÉ

Guide d’utilisation

INBOUW COMBI

KOELKAST-VRIESKAST

Handleiding

RÉFRIGÉRATEUR

PCI300G-E-2

EN - 1 -

Contents

SAFETY .................................................................................................... 2

WARNINGS .................................................................................................2

IMPORTANT SAFETY INSTRUCTIONS .....................................................3

Before installing and operating your appliance ............................................4

PARTS OF THE APPLIANCE AND THE COMPARTMENTS ................... 5

HOW TO OPERATE THE APPLIANCE ..................................................... 6

Thermostat Setting ......................................................................................6

Warnings about Temperature Adjustments ..................................................6

Accessories .................................................................................................7

Ice tray .......................................................................................................................7

Plastic scraper ............................................................................................................7

Temperature indicator ..................................................................................8

STORING FOOD IN THE APPLIANCE ..................................................... 9

Refrigerator Compartment ...........................................................................9

Freezer Compartment .................................................................................9

CLEANING AND MAINTENANCE .......................................................... 10

Defrosting operation .................................................................................. 11

Defrosting the Refrigerator Compartment ................................................. 11

Defrosting the Freezer Compartment ........................................................11

Replacing the Refrigerator Light Bulb ........................................................12

SHIPMENT AND REPOSITIONING ......................................................... 12

BEFORE CALLING YOUR AFTER SALES SERVICE ............................ 13

Tips for saving energy ...............................................................................14

INSTALLATION MANUAL ....................................................................... 15

Installation instructions and door reversibility ............................................15

TECHNICAL DATA .....................................................................................19

EN - 2 -

SAFETY PART - 1.

Notes:

Please read this instruction manual carefully before installing and using your appliance, and

keep it in a safe place for future reference. We are not responsible for any damage caused

by misuse or non-compliance with the instructions.

WARNINGS

• This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

• This appliance is intended to be used in household and similar applications such as

- staff kitchen areas in shops, ofﬁ ces and other working environments;

- farm houses and by clients in hotels, motels and other residential type environments;

- bed and breakfast type environments;

- catering and similar non-retail applications.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent

or similarly qualiﬁ ed persons in order to avoid a hazard.

• WARNING To avoid a hazard due to instability of the appliance, it must be ﬁ xed in

accordance with the instructions.

• WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in

structure, clear of obstruction.

• WARNING: Do not use mechanical devices or other means to accelerate the defrosting

process, other than those recommended by the manufacturer.

• WARNING: Do not damage the refrigerant circuit.

• WARNING: Do not use electrical appliances inside the food storage compartments of

the appliance, unless they are of the type recommended by the manufacturer.

• Do not store explosive substances such as aerosol cans with a ﬂ ammable propellant in

this appliance.

• WARNING: For making ice (ice cubes), use potable water only.

• INSTALLATION: DO NOT INSTALL THIS APPLIANCE IN AREAS THAT ARE TOO

HUMID OR TOO COLDS, SUCH AS THE CONSTRUCTION APPENDICES, GARAGES

OR WINE CELLARS.

• Never freeze defrosted food except if they have been cooked before, in order to eliminate

harmful bacteria. Never refreeze seafood that has been defrosted.

• The appliance should be placed on a horizontal ﬂ oor and keep the ventilation freely.

Don't try to replace or repair any components by yourself, ask the service agency for

help if necessary.

• Always handle the appliance to avoid any damage.

EN - 3 -

IMPORTANT SAFETY INSTRUCTIONS

• If you are discarding an old freezer or refrigerator with a lock / catch ﬁ tted to the door,

ensure that it is left in a disabled condition to prevent the entrapment of young children

when playing.

• As old refrigeration equipment may contain CFC’s which will damage the ozone layer,

when disposing of any refrigeration equipment please contact your local waste disposal

department for advice on the correct method of disposal.

• Unplug the appliance from the mains socket when not in operation and before cleaning.

• Remove food before cleaning the appliance.

• Do not insert oversized food as this could cause incorrect operation.

• Extreme caution must be used when moving the appliance.

• To turn the appliance off, turn the thermostat knob fully counter-clockwise to Off position,

then remove the plug from the mains socket.

• Do not give children ice-cream and water ices coming directly from the freezer as the

low temperature may cause ‘freezer burns’ on the lips.

• Do not use multiple sockets or extension cords.

• Do not plug in damaged, torn or old plugs.

• Do not pull, bend or damage the cord.

• Do not twist and bend the cables, and keep them away from hot surfaces.

• After installation make sure that the power cable is not trapped

underneath the appliance.

• Do not plug-in or out the plug from the socket with wet hands to

prevent electrocution!

• Do not place glass bottles or beverage cans in the freezer

department. Bottles or cans may explode.

• Do not place explosive or ﬂ ammable material in your fridge for

your safety. Place drinks with higher alcohol amount vertically in

the refrigerator compartment and keep the bottles tightly closed.

• When taking ice directly from the freezer, do not touch it, ice may

cause ice burns and/or cuts.

• Do not touch frozen food with wet hands! Do not eat ice-cream

and ice cubes immediately after you take them out of the freezer

compartment.

• Do not re-freeze the frozen goods after being melted. This may

cause health issues like food poisoning.

• Do not cover the body or top of fridge with lace. This affects the performance of your fridge.

• Do not operate any electrical appliances inside the refrigerator or freezer.

• Fix the accessories in the fridge during transportation to prevent damage to accessories.

EN - 4 -

Before installing and operating your appliance

Before starting to use your fridge, you should pay attention to the following points:

• Operating voltage for your fridge is 220-240 V at 50Hz.

• The plug must be accessible after installation.

• Your appliance may have a smell when it is operated for the ﬁ rst time; the smell will fade

away when your appliance starts to cool.

• Before making the connection to the power supply, ensure that the voltage on the rating

label corresponds to the voltage of electrical system in your home.

• Insert the plug into a socket with an efﬁ cient ground connection. If the socket has no

ground contact or the plug does not match, please call an authorised electrician for

assistance.

• The appliance must be connected with a properly installed fused socket. Power supply

(AC) and voltage at the operating point must correspond to the details stated on the

rating label of the appliance (located on the inside left of the appliance).

• We do not take responsibility for damages that may occur as a result of usage without

grounding.

• Place your fridge in a place where it is not exposed to direct sunlight.

• Your fridge should never be used outdoors or left under the rain.

• Your appliance should be at least 50 cm away from stoves, gas ovens and heater cores,

and should be at least 5 cm away from electrical ovens.

• Do not place heavy items on the appliance.

• Clean the appliance thoroughly, especially in the interior, before use (See Cleaning and

Maintenance).

• The installation procedure into the kitchen unit is given in the Installation Manual. This

product is intended to be used in proper kitchen units only.

• The adjustable front legs should be adjusted to an appropriate height to allow your

appliance to operate in a stable and proper way. You can adjust the legs by turning

them clockwise (or counter-clockwise). This should be done before placing food in the

appliance.

• Before using your fridge, wipe all parts with warm water and one

teaspoon of sodium bicarbonate, and then rinse with clean water

and dry. Place all parts after cleaning.

• Install the distance adjustment spacer (the part with white vanes

at the rear) by turning it 90° as shown in the ﬁ gure to prevent the

condenser from touching the wall.

Note:

• When it is operated for the ﬁ rst time or after transportation, keep your fridge in the upright

position for 3 hours before you plug it in. Otherwise, you may damage the compressor.

EN - 5 -

PARTS OF THE APPLIANCE AND THE

COMPARTMENTS

PART - 2.

A) Refrigerator compartment

B) Freezer compartment

1) Thermostat knob

2) Refrigerator light & cover

3) Refrigerator shelves

4) Crisper cover

5) Crisper

6) Freezer compartment ﬂ ap door

7) Freezer compartment top drawer

8) Freezer compartment bottom drawer

9) Ice tray

10) Lower rack

11) Upper racks

12) Egg tray

EN - 6 -

Thermostat Setting

HOW TO OPERATE THE APPLIANCE PART - 3.

The thermostat automatically regulates the inside temperature of the compartments. Turn

the knob from position 1 to 5 to adjust to the desired temperature.

Freezer & Refrigerator Thermostat Setting

0 : Off position. In the Off position, the appliance does not operate (the cooling system is

switched off), but power supply is not interrupted.

1 – 2 : For short-term storage of food in the freezer compartment.

3 – 4 : For long-term storage of food in the freezer compartment.

5 : For freezing the fresh food. The appliance will work longer. Once your food is frozen,

you must readjust to the previous position.

Warnings about Temperature Adjustments

• It is not recommended that you operate your fridge in environments colder than 10°C in

terms of its efﬁ ciency.

• Temperature adjustments should be made according to the frequency of door openings

and the quantity of food kept inside the fridge.

• When ﬁ rst turned on, your fridge must operate continuously for 24 hours to reach a

satisfactory level of cooling. During this period, do not open the door too often or put too

much food on the shelves.

• If your fridge is turned off or unplugged, wait at least 5 minutes before restarting to

prevent damage to the compressor.

Thermostat knob

EN - 7 -

Accessories

Ice tray

• Fill the ice tray with ¾ full of potable water and place in freezer compartment.

• After the water completely turned into ice, you can slightly twist the tray as shown below

to loosen the ice cubes.

Notes for use:

- Clean and defrost your appliance regularly (See "Defrosting" section).

- Check the contents of the compartments every now and then.

- Store commercially prepared food in accordance with the instructions given on the package.

- Choose high-quality fresh food and make sure it is thoroughly clean before freezing it.

- Do not store poisonous or any dangerous substances in your freezer. It has been designed

for the freezing of edible food only.

- Do not consume food which has been frozen for an excessive length of time.

- Do not leave the door open for long periods, as this will make the appliance more costly to

run and cause excessive ice formation.

- Do not use sharp objects such as knives to remove the ice from the appliance. Only use a

plastic scraper.

- Do not put liquid-ﬁ lled bottles or sealed cans containing carbonated liquids into the freezer

as they may burst.

Plastic scraper

After a certain time, frost will appear in some parts of the freezer. You

should periodically remove the frost using the plastic scraper provided

with the product. Do not use sharp metal objects for this operation, they

could puncture the refrigerator circuit and cause irreparable damage to the

appliance.

EN - 8 -

Temperature indicator

In order to help you make the right settings, your

appliance has been ﬁ tted with a temperature indicator,

located in the coldest area of your refrigerator (that is,

just above the crisper).

To enjoy good food preservation in your refrigerator,

especially in the coldest area, make sure the logo “OK”

appears on the temperature indicator. If it does not, it

means the temperature setting is wrong.

Area Products

Upper shelves Cooked food, meals and any food to be consumed within a few days

Coldest area Meat, poultry, wild game and ﬁ sh.

Maximum preservation time: 1 to 2 days.

Fresh fruit, cooked meats.

Crisper Fresh vegetables and fruits

Inner door

The bottles will be kept in the lower racks, and the upper racks will be

for small volume daily products (yogurts, light cream…)

Butter, cheese and eggs will be put in the appropriate cabinets.

As the logo “OK” is represented on a black background, it is barely visible if the temperature

indicator is poorly lit. Correctly lighting the temperature indicator makes the logo easier to

see.

Every time you want to change the temperature setting, wait at least 12 hours until the

temperature is stable, and adjust it if necessary. Please note that you should turn the

thermostat knob by one level at a time.

After ﬁ lling the appliance with fresh foods or after opening the door frequently or during a

long period, the logo “OK” might not appear on the temperature indicator. This is normal.

If the evaporator of the refrigerator compartment (back side of the appliance) abnormally

gets covered with frost (appliance overloaded, high ambient temperature, frequent door

openings), you should set the thermostat knob to a lower position until the compressor

regularly stops again.

The ideal preservation temperature is different depending on the food type. As a consequence,

they should not be placed in the same area of the refrigerator:

EN - 9 -

Refrigerator Compartment

The refrigerator compartment is used for storing fresh food for a few days.

• Do not place food in direct contact with the rear wall of the refrigerator compartment.

Leave some space around food to allow circulation of air.

• Do not place hot food or evaporating liquid in the refrigerator.

• Wrap all food in food quality polythene bags or containers and make sure any air is

excluded.

• To reduce humidity and avoid formation of frost, never place liquids in unsealed

containers in the refrigerator.

• Meat of all types, wrapped in packages, is recommended to be placed on the glass shelf

just above the crisper, where the air is colder.

• You can put the fruits and vegetables into crisper without packing.

• To avoid the cold air escaping, try not to open the door too often, and not to leave it open

for a long time.

Freezer Compartment

The freezer compartment is used for freezing fresh foods and for storing frozen foods for the

period of time indicated on packaging, and for making ice cubes.

• For freezing fresh food; wrap and seal fresh food properly, that is the packaging

should be air tight and shouldn’t leak. Special freezer bags, aluminum foil (heavy grade,

in doubt double wrap), polythene bags and plastic containers are ideal.

• Do not allow the fresh food to be frozen to come into contact with the already frozen

food.

• Always mark the date and the content on the pack and do not exceed the stated storage

time.

• In case of a power failure or malfunction, the freezer compartment will maintain a

sufﬁ ciently low temperature for food storage for a few hours. However, avoid opening

the freezer door to slow down the temperature rise within the freezer compartment.

• The maximum amount of fresh foods that can be loaded in the freezer within 24 hours is

indicated on the rating label (see Freezing Capacity).

• Never place warm food in the freezer compartment.

• When purchasing and storing frozen food products; ensure that the packaging is

not damaged.

• The storage time and the recommended temperature for storing frozen foods are

indicated on the packaging. For storing and using, follow the manufacturer’s instructions.

If no information is provided, food should not be stored for more than 3 months.

• Place frozen food in the freezer compartment as soon as possible after buying it.

• Once the food is thawed, it must not be refrozen; you must cook it as quickly as possible

in order to consume or to freeze once again.

• Storage: If you want to use the maximum net capacity of the freezer compartment, you

can remove the drawers and store the items directly on the cooling tubes.

STORING FOOD IN THE APPLIANCE PART - 4.

EN - 10 -

CLEANING AND MAINTENANCE PART - 5.

• Unplug your appliance.

• Remove all substances.

• Clean the inside and outside walls with a clean sponge or soft cloth using warm and

soapy water. Do not try to wash your appliance by pouring water.

• Remove the parts individually and clean with soapy water. Do not put them in the

washing machine.

• Rinse well and wipe dry with a clean soft cloth.

• Make sure that no water is coming into contact with the electrical system of the thermostat

setting or of the lamp.

• Regularly check the door gasket.

You should clean the condenser with broom at least once a year

in order to save energy and increase the productivity of your

appliance.

Never use ﬂ ammable, explosive or corrosive material like thinner, gas, acid for

cleaning.

Note: If the appliance is not to be used for a long period of time, it is recommended to

remove all food, defrost the appliance, clean the inside of the appliance and leave the doors

open to allow the air to circulate, thus avoiding unpleasant smells.

EN - 11 -

Defrosting the Refrigerator Compartment

• The fridge defrosting process is carried out automatically every time the compressor

stops. The defrost water is automatically routed to the drain port and into a tray placed

on the top of the compressor to the rear of the appliance from which it evaporates.

• The evaporating tray and the defrost water drain hole should be cleaned periodically with

defrost drain plug to prevent the water from collecting at the bottom of the refrigerator

instead of ﬂ owing out.

Defrosting the Freezer Compartment

• The frost covering the shelves of the freezer compartment should be removed

periodically.

• Do not use sharp metal objects for this operation. They could puncture the refrigerator

circuit and cause irreparable damage to the unit. Use the plastic scraper provided.

• When there is more than 5 mm of frost on the shelves, defrosting must be done.

• Before defrosting operation, place the frozen food in a cool place after wrapping it in

sheets of newspaper in order to obtain its temperature steady for long time.

• To accelerate the defrosting process place one or more basins of warm water in the

freezer compartment.

• Dry the inside of the compartment with a sponge or a clean cloth.

• Once the unit has been defrosted, place the food into freezer and remember to consume

them in a short period of time.

Defrosting operation

Note: The refrigerator and freezer compartments of your appliance should be defrosted

twice a year.

(Evaporating tray)

EN - 12 -

Replacing the Refrigerator Light Bulb

1. Unplug the unit from the power supply,

2. Remove the refrigerator light cover (A) by

pressing the hooks placed on both sides of the

cover.

3. Change the light bulb (B) with a new one (E14,

no more than 15 W).

4. Replace the light cover and plug the unit.

• Original package and foam may be kept for re-transportation.

• During transportation, the appliance should be empty and its doors should be closed.

• You should fasten your fridge with thick package, bands or strong cords and follow the

instructions for transportation on the package.

• Remove movable parts (shelves, accessories, crisp, etc.) or ﬁ x them into the fridge

against shocks using bands during re-positioning and transportation.

• Carry your fridge in the upright position.

SHIPMENT AND REPOSITIONING PART - 6.

Your appliance uses R600a as a refrigerant. Therefore you should be careful during

shipment and installation to prevent your appliance’s cooler elements from being damaged.

Although R600a is an environmentally friendly and natural gas, it is explosive. In the event of

a leak caused by damage to the cooler elements, move your fridge from open ﬂ ame or heat

sources and ventilate the room where the appliance is located for a few minutes.

EN - 13 -

BEFORE CALLING YOUR AFTER SALES SERVICE PART - 7.

If your refrigerator is not working properly, please check the following before calling for help.

Your appliance is not working.

Check that;

• The appliance is plugged in.

• The general switch in your home is not disconnected.

• The voltage is sufﬁ cient. To check this, plug in another appliance that you know which is

working into the same socket.

Your appliance performs poorly.

Check that;

• You have not overloaded the appliance ,

• The thermostat is not set to position "1" (if it is, you will have to set the thermostat to a

suitable value)

• The doors are closed perfectly ,

• There is no dust on the condenser ,

• There is enough place at the rear and side walls.

Your appliance is noisy when operating.

The cooling gas which circulates in the refrigerator circuit may make a slight noise (bubbling

sound) even when the compressor is not running. Do not worry this is quite normal. If these

sounds are different check that;

• The appliance is correctly levelled.

• Nothing is coming in contact with the rear of the appliance.

• The stuffs on the appliance are not vibrating.

There is water in the lower part of the refrigerator.

Check that;

The drain hole for defrost water is not clogged(Use defrost drain plug to clean the drain hole)

Your appliance is not cooling sufﬁ ciently.

Your fridge is designed to operate in the ambient temperature intervals stated in the

standards, according to the climate class stated on the rating label. Operating your appliance

outside the stated temperatures is not recommended.

Climate class

Ambient Temperature (

o

C)

T Between 16 and 43

o

C

ST Between 16 and 38

o

C

N Between 16 and 32

o

C

SN Between 10 and 32

o

C

EN - 14 -

Tips for saving energy

1– Install the appliance in a cool, well-ventilated room , but not in direct sunlight or near

any heat source (radiator, cooker.. etc). Otherwise use an insulating plate.

2– Allow warm food and drinks to cool down outside the appliance.

3– When thawing frozen food, place it in the refrigerator compartment. The low

temperature of the frozen food will help to cool the refrigerator compartment when it is

thawing, thus saving energy.

4– When placing drinks and soups, make sure they are covered. Otherwise humidity

increases in the appliance, extending the time needed to reach optimum performance.

Also covering drinks and soups helps to save smell and taste.

5– When placing food and drinks, open the appliance door as brieﬂ y as possible.

6– Do not move the shelves within the appliance so as to keep the appropriate cooling

zones.

7– Door gasket must be clean and pliable. Replace gaskets if worn.

Conformity Information

• Normal class is deﬁ ned for the environment temperatures between 16°C and 32°C in

accordance with the TS EN ISO 15502 Standards.

• The appliance is designed in compliance with the EN15502, IEC60335-1 / IEC60335-2-

24, 2004/108/EC standards.

Recommendations

• The compressor protection thermal fuse will cutout after sudden power breakdowns or

after unplugging the appliance, because the gas in the cooling system is not stabilised.

This is quite normal, and the fridge will restart after 4 or 5 minutes.

• The cooling unit of your refrigerator is hidden in the rear wall. Therefore, water droplets or

icing may occur on the rear surface of your fridge due to the operation of the compressor

in speciﬁ ed intervals. This is normal. There is no need to perform a defrosting operation

unless the icing is excessive.

• If the problem persists after you have followed all the instructions above, please consult

the nearest authorised service.

• The appliance you have purchased is designed for domestic use and can be used only

at home and for the stated purposes. It is not suitable for commercial or common use. If

the consumer uses the appliance in a way that does not comply with these features, we

emphasise that the producer and the dealer shall not be responsible for any repair and

failure within the guarantee period.

EN - 15 -

Installation instructions and door reversibility

Installation

! Before installation, read the instructions carefully.

! Fit the refrigerator/freezer in stable kitchen units only.

! If necessary, reverse the door according to instructions.

! Check the installation dimensions according to ﬁ g.C. The position of the joint between

the unit doors must be level with the position of the joint between the appliance doors.

1. See ﬁ g.A for the necessary attachment components.

2. Insert trim ﬂ ap

1

into slot and screw by screws

6

. (ﬁ g.D)

3. Pass the power cord through ventilation shaft and position it so that the appliance could

be easily plugged in once it has been installed. (ﬁ g.B - ﬁ g.C)

4. Take out the trim gasket

2

located on the side panel of the appliance and stick it on

reverse side of the door hinges of the appliance. (ﬁ g.D - ﬁ g.E)

5. Raise appliance and slide into kitchen unit. Push appliance to the reverse side of door

hinges providing that trim gasket

2

covers space between appliance and the kitchen unit.

6. Align front feet with front surface of kitchen unit. (ﬁ g.F)

7. Screw the front feet by using screws

5

. (ﬁ g.F)

8. Screw trim ﬂ ap

1

to kitchen unit using screws

5

. (ﬁ g.G)

9. Screw ﬁ xing bracket

11

, as leaned to kitchen unit by using screws

5

. Repeat this for the

opposite side. (ﬁ g.H)

10. Screw guides

3

to appliance doors with screws

6

. Lean appliance doors to unit door as it

is opened at right angle. Slide rails

4

into guides

3

aligning the groove. Screw the rails

4

to

the unit doors with screws

5

. (ﬁ g.J)

11. Set 1~2 mm gap on handle side between unit itself and unit doors by adjusting guides

3

.

That is vital for appliance performance. (ﬁ g.J)

INSTALLATION MANUAL

EN - 16 -

Figure A

Figure B Figure C

Figure D Figure E

A B C D E

1770 722 684 934 1770-1790

mm

EN - 17 -

Figure F Figure G Figure H

Figure J

EN - 18 -

Door reversing

1. Unscrew upper door hinge

15

and take upper door

14

to safe place.

2. Unscrew door hinge pin

16

and screw it to opposite side ﬁ rmly and take to safe place.

3. Unscrew middle door hinge

12

and take lower door

10

to safe place. Screw back ﬁ xing

bracket

11

to original position without middle door hinge

12

.

4. Take door lower pin

18

to opposite side.

5. Take hole plugs

17

to empty holes on opposite side.

6. Place lower door

10

over door lower pin

18

and close onto cabinet.

7. Unscrew ﬁ xing bracket

13

. Position middle door hinge

12

onto lower door

10

. Place ﬁ xing

bracket

11

onto middle door hinge

12

and screw together onto cabinet ﬁ rmly.

8. Place upper door

14

over middle door hinge

12

and position upper door hinge

15

over

upper door

14

and then screw upper door hinge

15

ﬁ rmly onto opposite side of original

position.

Figure K

EN - 19 -

TECHNICAL DATA

Brand

Appliance type Fridge-Freezer

Star rating

Net Freezer volume (l.)

68L

Net Fridge volume (l.)

158L

Freezing capacity (kg/24h)

3kg

Climate Class +Ambient Range

N (+16

o

C to +32

o

C)

Energy class

(1)

A+

Gross weight (kg) 51,25

Power consumption (kWh/year)

(2)

257

Supply voltage (V/Hz)

220-240V / 50Hz

Light Power (Watts)

15W

Noise [dB(A)re 1 pW]

42 dB

Refrigerating agent

R600a / 55g

Outside dimensions (W x D x H)

540 X 545 X 1770

Insulation Blowing Gas

Cyclo pentane

(1) Energy class: A.....G (A= economical G=less economical)

(2) The real power consumption depends on using conditions and appliance location.

La page charge ...

Proline PCI300G-E-2 Mode d'emploi

Proline PCI300G-E-2 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents