Samsung PS50A566 Manuel utilisateur

imagine the possibilities

Plasma TV

user manual

Thank you for purchasing this Samsung product.

To receive more complete service, please register your

product at

www.samsung.com/global/register

Model Serial No.

English - 2

User Instructions

 Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the

plasma monitor panel for more than 2 hours as it can cause screen image retention. This image

retention is also known as “screen burn”. To avoid such image retention, reduce the degree of

brightness and contrast of the screen when displaying a still image.

 Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place

over 2000m in height so do not install and operate there.

 Heat on the top of the PDP TV

The top side of the product may be hot after long period of use as heat dissipates from the panel

through the vent hole in the upper part of the product. This is normal and does not indicate any defect

or operation failure of the product. However, children should be prevented from touching the upper

part of the product.

 The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding

environment such as temperature or humidity. This is normal and not a defect of the unit.

 Cell Defects

The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require

sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.

These pixels will have no impact on the performance of the product.

 Avoid operating the TV at temperatures below 5°C(41°F)

 A still image displayed too long may cause permanent damage to the PDP Panel.

Watching the PDP TV in 4:3 format for a long period of time may leave traces

of borders displayed on the left, right and centre of the screen caused by the

difference of light emission on the screen. Playing a DVD or a game console

may cause similar effect to the screen. Damages caused by the above effect are

not covered by the Warranty.

 Afterimage on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may

produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when

displaying still images.

 Warranty

- Warranty does not cover any damage caused by image retention.

- Burn-in is not covered by the warranty.

 Installation

Be sure to contact an authorized service centre, when installing your set in a location with heavy

dust, high or low temperatures, high humidity, chemical substance and where it operates continually

such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.

Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2)

digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive

DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with

the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be

available in some countries.

English - 3

Symbols

¯

Press

Important

Note

Contents

General Information

 User Instructions ............................................. 2

 Checking Parts ................................................ 4

 Using the Stand-Base ..................................... 4

 Control Panel ................................................. 5

 Connection Panel ............................................ 6

 Viewing the Remote Control ........................... 8

Operation

 Switching Your Television On and Off ............. 9

 Viewing the Menus .......................................... 9

 Plug & Play Feature ......................................10

 Using the TOOLS Button .............................. 12

 Viewing External Signal Sources ..................12

 Editing Device Names ................................... 13

Channel Control

 Storing Channels Automatically .................... 14



Storing Channels Manually ........................... 15



Viewing the EPG (Electronic Programme

Guide) Information ....................................... 16



Viewing All Channels .................................... 17



Erasing and Adding Channels ....................... 18



Setting Your Favourite Channels ..................19



Reserving a Program (Time Viewing) ........... 20



Conﬁrming a Viewing Reservation ................ 21



Assigning Names to Channels ...................... 22



Sorting the Stored Channels - Analogue ....... 23



Selecting and Deselecting All Channels ....... 24



Storing Channels in Memory (Auto Store) .... 24



Setting the Channel Mode ............................ 24



Locking Channels ......................................... 25



Fine Tuning Analogue Channels ................... 25



Viewing Signal Information ........................... 26



LNA (Low Noise Ampliﬁer) ............................ 26

Picture Control

 Changing the Picture Standard ..................... 27



Customizing the Picture Settings ..................27



Conﬁguring Detailed Settings on the Picture 28



Picture Options ............................................. 29



Resetting the Picture Settings to the Factory

Defaults ......................................................... 31

Sound Control



Sound Features ............................................ 32



Selecting the Sound Mode

(depending on the model) .............................34



Connecting Headphones (Sold separately) .. 34

Function Description

 Time Features ............................................... 35

 Language / Change PIN / Parental Lock /

Subtitle / Teletext Language / Preference /

Light Effect / Melody/ Entertainment /

Energy Saving / PIP ..................................... 36



Upgrading the Software ................................ 39



Common Interface ........................................ 40

PC Display

 Setting up Your PC Software

(Based on Windows XP) ...............................41



Input Mode (PC) ............................................ 42



Setting the PC ............................................... 43

WISELINK

 Using the WISELINK Function ...................... 45



Using the Photo List ...................................... 46



Viewing a Photo or Slide Show ..................... 52



Using the Music List ...................................... 56



Playing a Music File ...................................... 61

 Using the Setup Menu .................................. 63

About Anynet

+

 What is Anynet

+

? .......................................... 64



Connecting Anynet

+

Devices ........................ 64



Setting Up Anynet+ ....................................... 65



Scanning and Switching between

Anynet

+

Devices ........................................... 65



Recording ...................................................... 66



Listening through a Receiver ........................ 67



Check Points before Requesting Service ..... 67

Appendix

 Teletext Feature (depending on the model) .. 68



Wall Mount Kit Speciﬁcations (VESA) ........... 70



Auto Wall - mount adjustment

(Sold separately) ........................................... 71



How to assemble the Stand-Base

(depending on the model) ............................. 72



Securing the TV to the Wall .......................... 73



Troubleshooting ............................................ 74



Speciﬁcations ................................................ 75

English

English - 4

Checking Parts

Owner’s Instructions Remote Control/

AAA Batteries

Power Cord Cloth-Clean Warranty Card/

Safety Guide Manual

(Not available in all

locations)

Cover-Bottom / Screws (2ea)

(Refer to page 71)

Ferrite Core for

Power Cord

Ferrite Core for

S-Video

Ferrite Core for

Component

Sold Separately

Antenna Cable Component Cables Audio Cables PC Cable

Scart Cable PC Audio Cable HDMI Cable HDMI/DVI Cable

¯

Ferrite Core (Power Cord, S-Video, Component)

The ferrite cores are used to shield the cables from interference.

When connecting a cable, open the ferrite core and clip it around

the cable near the plug.

Using the Stand-Base

¯





Two or more people

should carry the PDP.

Never lay the PDP on the

floor because of possible

damage to the screen.

Always keep the PDP

upright.







The PDP can rotate 20

degrees in right and left

directions.

-20° ~ 20°

English - 5

Control Panel

1

SOURCE

Toggles between all the available input sources

(TV, Ext.1, Ext.2, AV, S-Video, Component, PC,

HDMI1, HDMI2/DVI, HDMI3, USB).

¯

In the on-screen menu, use this button as

you would use the

ENTER button on the

remote control.

2

MENU

Press to see an on-screen menu of your TV’s

features.

3

– +

Press to increase or decrease the volume. In

the on-screen menu, use the

–

+ buttons

as you would use the

◄ and ► buttons on the

remote control.

4

Press to change channels.

In the on-screen menu, use the

buttons as you would use the

▲ and ▼ buttons

on the remote control.

5

Power Indicator

Blinks and turns off when the power is on and

lights up in stand-by mode.

6

POWER

Press to turn the TV on and off.

7

Remote Control Sensor

Aim the remote control towards this spot on the

TV.

8

Speakers

¯

The product colour and shape may vary depending on the model.

Front Panel

English - 6

Connection Panel

Continued...







Whenever you connect an audio or video system to your set, ensure that all elements are

switched off.







When connecting an external device, match the colour of the connection terminal to the cable.

1

POWER IN

Connect the supplied power cord.

2

COMPONENT IN

Audio (AUDIO L/R) and video (Y/P

B/PR) inputs

for Component.

3

PC IN(PC) / AUDIO

Connect to the video and audio output jack on

your PC.

4

EXT 1, EXT 2

Inputs or outputs for external devices, such as

VCR, DVD, video game device or video disc

players.

Input/Output Specification

Connector

Input Output

Video Audio(L/R) RGB Video + Audio(L/R)

EXT 1   

Only TV or DTV

output is available.

EXT 2

 

Output you can

choose.

5

DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio Component.

6

AUDIO OUT(AUDIO R/L)

Connect RCA audio signals from the TV to an

external source, such as Audio equipment.

7

SERVICE

− Connector for service.

− Connect the serial jack between the

electro-motion wall mount bracket and your

TV when you want to adjust the TV viewing

angle using your remote control.

Rear Panel

¯

The product colour and shape may vary depending on the model.

Cable Television

Network

or

1

432685

9

7

English - 7

8

HDMI IN 1,2

- No additional Audio connection is needed

for an HDMI to HDMI connection.

- When using an HDMI/DVI cable connection,

you must use the HDMI IN 2 jack.

¯

What is HDMI?

- “High Definition Multimedia interface”

allows the transmission of high definition

digital video data and multiple channels

of digital audio.

- The HDMI/DVI terminal supports DVI

connection to an extended device with

the appropriate cable (not supplied). The

difference between HDMI and DVI is that

the HDMI device is smaller in size, has

the HDCP (High Bandwidth Digital Copy

Protection) coding feature installed, and

supports multi - channel digital audio.

DVI IN(HDMI2) AUDIO L/R

DVI audio outputs for external devices.

9

ANT IN

75Ω Coaxial connector for Aerial/Cable

Network.

Supported modes for HDMI/DVI and Component

480i 480p 576i 576p 720p

1080i

1080p

HDMI/DVI 50Hz

XXXOO

O

HDMI/DVI 60Hz

XOXXO

O

Component O O O O O

O

1

COMMON INTERFACE Slot

Insert CI (Common Interface) card into the slot.

(refer to page 40)

− When ‘CI Card’ isn’t inserted in some

channels, “Scramble Signal” is displayed on

the screen.

− The pairing information containing a

telephone number, CI CARD ID, Host

ID,and other information will be displayed

in about 2~3 minutes. If an error message

is displayed, please contact your service

provider.

− When the channel information configuration

has finished, the message “Updating

Completed” is displayed, indicating that the

channel list is now updated.

¯ Insert the CI-Card in the direction marked

on it.

2

HDMI IN 3

Connect to the HDMI jack of a device with

HDMI output.

3

WISELINK

Connect a USB mass storage device to view

photo files (JPEG) and play audio files (MP3).

4

S-VIDEO or VIDEO / AUDIO L/R

Video (S-Video or Video) and audio inputs

for external devices, such as a camcorder or

VCR.

5

HEADPHONES JACK

You can connect a set of headphones if you

wish to watch a television programme without

disturbing the other people in the room.

¯

Prolonged use of headphones at a high

volume may damage your hearing.

Ê

The product colour and shape may vary depending on the model.

Side Panel

or

5

2

4

1

3

English - 8

Viewing the Remote Control

The performance of the remote control may be affected by bright light.

1

POWER button

(turns the TV on and off)

2

Selects the TV and DTV

mode directly

3

Number buttons for direct

channel access

4

One/Two-digit channel

selection

5

Temporary sound switch-off

6

Volume increase

Volume decrease

7

Electronic Program Guide

(EPG) display

8

Use to quickly select

frequently used functions.

9

Control the cursor in the

menu

0

Use to see information on

the current broadcast

!

Use these buttons in the

Channel list and WISELINK,

etc.

#

Press to select the optional

display and sound modes for

sports, cinema and games.

$

VCR/DVD Function (Rewind,

Stop, Play/Pause, Fast/

Forward)

%

Available source selection

^

Previous channel

&

Next channel

Previous channel

*

Displays the main on-screen

menu

(

This function enables you to

view and play photo (JPEG)

and audio files (MP3) from

an external device. (See

page 46 (JPEG), 56 (MP3))

)

Returns to the previous

menu

a

Exit the on-screen menu

b

Picture size selection

c

Use this when connecting

a SAMSUNG DMA (Digital

Media Adapter) device

through an HDMI interface

and switching to DMA

mode.(The DMA button is

optional.)

For more information on

the operating procedures,

refer to the user manual

of the DMA. This button

is available when

“Anynet+(HDMI-CEC)" is

“On” (see page 64)

d

Digital subtitle display

e

Channel control button

(Refer to page 18)

Teletext Functions

(Refer to page 68)

2

Exit from the teletext display

(depending on the model)

7

Teletext store

8

Teletext size

0

Teletext reveal

!

Fastext topic selection

@

Teletext display/mix both

teletext information and the

normal broadcast

%

Teletext mode selection

(LIST/FLOF)

^

Teletext sub page

&

P :Teletext next page

P

:Teletext previous page

*

Teletext index

)

Teletext hold

a

Teletext cancel

Continued...

W.LINK

English - 9

Installing Batteries in the Remote Control

1 Lift the cover at the back of the remote control upward as

shown in the figure.

2 Install two AAA size batteries.

¯

 Make sure to match the “+” and “–” ends of the

batteries with the diagram inside the compartment.

 Do not mix battery types, i.e. alkaline and manganese.

3 Close the cover as shown in the figure.

¯

Remove the batteries and store them in a cool and dry

place if you won’t be using the remote control for a long

time. The remote control can be used up to about 23 feet

from the TV. (Assuming typical TV usage, the batteries last

for about one year.)

¯

If the remote control doesn’t work! Check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power cut, or is the power cord unplugged?

5. Is there a special fluorescent light or a neon sign nearby?

Switching Your Television On and Off

The mains lead is attached to the rear of the television.

1 Plug the mains lead into an appropriate socket.

¯

The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

2 Press the

(Power) button (On/Off) on the front of the television or press the POWER button on

the remote control to switch the television on. The channel that you were watching last is re-selected

automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing

Channels Automatically” on page 14 or “Storing Channels Manually” on page 15.

¯

If the television is initially powered on, several basic customer settings proceed automatically.

Refer to “Plug & Play Feature” on page 10.

3 To switch the television off, press the

(Power) button (On/Off) on the front of the television or press

the

POWER button on the remote control.

4 To switch the TV on, press the

(Power) button (On/Off) on the front of the TV or press the POWER

button or number buttons on the remote control.

Viewing the Menus

1 Press the MENU button.

The main menu is displayed on the screen.

Its left side has six icons:

Picture, Sound, Channel,

Setup, Input, and Application

2 Press the ▲ or ▼ button to select one of the icons.

Press the

ENTER button to access the icon’s sub-menu.

3 Press the ▲ or ▼ button to move to items in the menu.

Press the

ENTER button to enter items in the menu.

4 Press the ▲/▼/◄/► button to change the selected items.

Press the

RETURN button to return to the previous menu.

5 Press the EXIT button to exit from the menu.

W.LINK

Mode : Standard

Cell Light : 7

Contrast : 95

Brightness : 45

Sharpness : 50

Colour : 50

Tint (G/R) : G50/R50

Detailed Settings

Picture

English - 10

Plug & Play Feature

When the television is initially powered on, several basic customer settings proceed automatically

and subsequently.The following settings are available.



If you accidentally select the wrong country for your TV, the characters on the screen may be wrongly

displayed.



Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2)

digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive

DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with

the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not

be available in some countries.

¯

The Screen Saver is activated if there is no remote control key input for longer than 1 minute while

Plug & Play is running.

1 If the television is in standby mode, press the POWER

button on the remote control. The message

Les menus

Langue, Enr. démo, Canaux et Heure seront définis. is

displayed.

2 Press the ENTER button, Select the OSD Language

menu is automatically displayed. Press the

ENTER

button.

3 Select the appropriate language by pressing the ▲ or ▼

button. Press the

ENTER button to confirm your choice.

The message

Select ‘Home Use’ when installing this

TV in your home. is displayed.

4 Press the ◄ or ► button to select Store Demo or Home

Use, then press the ENTER button. The message to

check the connected status of the antenna is displayed.

¯

The default selection is Home Use.

¯

We recommend setting the TV to Home Use mode

for the best picture in your home environment.

¯

Store Demo mode is only intended for use in retail

environments.

¯

If the unit is accidentally set to Store Demo mode

and you want to return to

Home Use (Standard):

Press the Volume button on the TV. When the

volume OSD is displayed, press and hold the

MENU

button on the TV for 5 seconds.

5 Press the ▲ or ▼ button to select the channel source to

memorize. Press the ENTER button to select Start.

Digital & Analogue: “Digital” and “Analogue” channels.

Digital: “Digital” channels.

Analogue: “Analogue” channels.

The channel search will start and end automatically.

Press the ENTER button at any time to interrupt the

memorization process.

After all the available channels are stored, the message Set the Clock Mode is displayed.

Continued...

Plug & Play

Auto Store in progress. Channel 6

Digital Channels : 0

Analogue Channels : --

Stop

Enter Skip

1%

Plug & Play

Les menus Langue, Enr. démo, Canaux et Heure seront définis.

Entrer

OK

Plug & Play

Select the OSD Language

Enter

Menu Language : English

Move

▲

Nederlands

English

Soumi

▼

Plug & Play

Select the channel source to memorize.

Digital & Analogue

Digital

Analogue

Start

EnterMove

Start

Skip

Plug & Play

Select 'Home Use' when installing this TV in your home.

Home Use

Store Demo

Move Enter

English - 11

¯

To stop the search before it has finished, press the

ENTER button with stop selected.

Press the ◄ or ► button to select Yes, then press

the ENTER button. The Auto Store menu then

reappears. Press the ENTER button when channel

memorization is completed.

6 The message Set the Clock Mode is displayed. Press

the ENTER button. Press the ▲ or ▼ button to select

Manual for setting the current time manually, then press

the ENTER button. The message Set current date and

time. is displayed.

¯

If you select Auto, the message Enjoy your viewing

is displayed. If you have received a digital signal, the

time will be set automatically.

7 Press the ◄ or ► button to move to Day, Month, Year,

Hour or Minute. Set the date and time you want by

pressing the ▲ or ▼ button, then press the ENTER

button.

¯

You can set the Day, Month, Year, Hour and Minute

directly by pressing the number buttons on the

remote control.

8 The message Enjoy your viewing. is displayed. When

you have finished, press the ENTER button.

¯

Even if the ENTER button is not pressed, the

message will automatically disappear after several

seconds.

If you want to reset this feature …

1 Press the

MENU button to display the menu.

2 Press the ▲ or ▼ button to select Setup, then press the

ENTER button.

3 Press the ENTER button again to select Plug & Play.

4 Enter your 4 digit PIN number. The default PIN number of

a new TV set is “0-0-0-0”.

¯

For further details on setting up options, refer to the

pages 10-11.

¯

The Plug & Play feature is only available in the TV

mode.

Plug & Play

Auto Store is completed.

Digital channels: 20

Analogue channels: 36

OK

Enter

OK

Plug & Play

Enjoy your viewing.

Skip

Plug & Play ►

Language : English

Time

Change PIN

Parental Lock

Subtitle

Teletext Language : ----

Preference

Setup

Plug & Play

Set the Clock Mode.

Clock Mode : Auto

Auto

Manual

Enter Skip

Move

Plug & Play

Set current date and time

01

Day

01

Month

2008

Year

Hour

00

Minute

SkipEnterAdjustMove

00

Plug & Play

The Menu Language, Store Demo, Channels and Time will

be set.

Enter PIN

Return

0~9

English - 12

Viewing External Signal Sources

You can switch between viewing signals from connected

equipment, such as a VCR, DVD, Set-Top Box, and the TV

source.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Input, then press the

ENTER button.

3 Press the ENTER button again to select Source List.

4 Press the ▲ or ▼ button to select the signal source, then

press the ENTER button.

Available signal sources: TV,Ext1,Ext2, AV, S-Video,

Component, PC, HDMI1, HDMI2/DVI, HDMI3, USB

¯

You can choose only those external devices that are

connected to the TV.

¯

Using the Color buttons on the remote with the Source list.

¯

You can select these options simply by pressing the

SOURCE button on the remote control.

¯

To watch television programme again, press the TV/DTV

button and select the channel number required.

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The

“TOOLS” menu changes depending on which external input mode you are viewing.

1 Press the TOOLS button.

The Tools menu will appear.

2 Press the ▲ or ▼ button to select a menu, then press the

ENTER button.

3 Press the ▲/▼/◄/►/ENTER buttons to display, change, or

use the selected items.

For a more detailed description of each function, refer to

the corresponding page.

• Device List, see page 65

• Picture Mode, see page 27

• Sound Mode, see page 32

• Sleep Timer, see page 35

• SRS TS XT, see page 32

• Energy Saving, see page 38

• Dual I II, see page 34

• PIP, see page 38

• Red (Refresh): Refreshes the connecting external

devices.

•

(Option): Displays the Edit Name and Information

menus.

Source List

Edit Name

Input

TV

Ext.1

----

Ext.2

----

AV

----

S-Video

----

Component

----

PC

----

Refresh Option

Tools

Device List

Picture Mode : Standard

Sound Mode : Standard

Sleep Timer : Off

SRS TS XT : Off

Energy Saving : Off

Dual I II : Mono

Move Enter Exit

English - 13

Editing Device Names

You can give a name to the external source.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Input, then press the

ENTER button.

3 Press the ▲ or ▼ button to select Edit Name, then press

the

ENTER button.

4 Press the ▲ or ▼ button to select the external source to

be edited, then press the

ENTER button.

5 Select the required device by pressing ▲ or ▼, then press

the

ENTER button.

Available device names:

VCR, DVD, Cable STB, Satellite

STB, PVR STB, AV Receiver, Game, Camcorder, PC, TV,

IPTV, Blu-Ray, HD DVD, Digital Media Adapter.

6 Press the EXIT button to exit.

Input

Source List

Edit Name ►

Edit Name

Ext.1 :

----

►

Ext.2 :

----

AV :

----

S-Video :

----

Component :

----

PC :

----

HDMI1 :

----

Enter ReturnMove

Edit Name

Ext 1 :

----

Ext 2 :

----

AV :

----

S-Video :

----

Component :

----

PC :

HDMI1 :

Enter ReturnMove

----

VCR

DVD

Cable STB

Satellite STB

PVR STB

English - 14

Storing Channels Automatically

You can scan for the frequency ranges available to you (availability depends on your country).

Automatically allocated programme numbers may not correspond to actual or desired programme

numbers. However you can sort numbers manually and clear any channels you do not wish to

watch.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

3 Press the ▲ or ▼ button to select Auto Store, then press

the

ENTER button.

4 Press the ▲ or ▼ button to select the channel source to

memorize. Press the

ENTER button to select Start.

¯

Digital & Analogue: “Digital” and “Analogue”

channels.

Digital: “Digital” channels.

Analogue: “Analogue” channels.

¯

Scans for all channels with active broadcast stations

and stores them in the TV’s memory.

¯

If you want to stop Auto Store, press the ENTER

button.

The

Stop Auto Store? message will be displayed.

Select

Yes by pressing the ◄ or ► button, then press

the

ENTER button.

5 Press the

EXIT button to exit.

¯

When there is a locked channel by Channel Lock

setting, PIN input screen appears. (refer to page 25)

Channel

Auto Store

►

Manual Store

Full Guide

Mini Guide

Default Guide : Mini Guide

Channel List

Channel Mode : Added Channels

Child Lock : On

Auto Store

Auto Store is progress. Channel 6

Digital Channels : 0

Analogue Channels : --

Stop

Enter

4%

Return

Auto Store

Select the channel source to memorize.

Digital & Analogue

Digital

Analogue

Start

EnterMove

Start

Return

Plug & Play

Auto Store is incomplete.

Digital channels: 20

Analogue channels: 36

OK

Enter Skip

English - 15

Storing Channels Manually

You can store television channels, including those received via cable networks.

When storing channels manually, you can choose:

 Whether or not to store each of the channels found.

 The programme number of each stored channel which you wish to identify.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

3 Press the ▲ or ▼ button to select Manual Store, then

press the

ENTER button.

4 Select the required option by pressing the ▲ or ▼ button,

then press the

ENTER button.

5

When you are satisfied with your setting, press the ENTER button.

6 Press the EXIT button to exit.

Digital Channel

 Channel

Press the ▲, ▼ or numeric buttons (0~9) to select a channel.

The available channels are 5~69. The corresponding

frequency for the selected channel is automatically set

 Frequency

You can specify the frequency (KHz) using the numeric buttons

(0~9). If you do not know the exact frequency, follow the above

step to select the frequency automatically using channel.

 Bandwidth

Press the ▲ or ▼ button to select a bandwidth. The

available bandwidths are 7 and 8 MHz.

Analogue Channel

 Programme (Programme number to be assigned to a

channel)

Press the ▲ or ▼ button until you find the correct number.

¯

You can also select the channel number directly by

pressing the numeric buttons (0~9).

 Colour System: Auto/PAL/SECAM/NTSC4.43

Press the ▲ or ▼ button to select the required colour standard.

 Sound System: BG/DK/I/L

Press the ▲ or ▼ button to select the required sound

standard.



Channel (When you know the number of the channel to be stored)

Press the ▲ or ▼ button to select C (Air channel) or S

(Cable channel).

Press the ► button, then press the ▲ or ▼ button to select

the required number.

¯

You can also select the channel number directly by

pressing the numeric buttons (0~9).

¯

If there is abnormal sound or no sound, re-select the sound standard required.

 Search (When you do not know the channel numbers)

Press the ▲ or ▼ button to start the search.

The tuner scans the frequency range until the first channel or the channel that you selected is

received on the screen.

 Store (When you store the channel and associated programme number)

Set to

OK by pressing the ENTER button.

¯

Channel mode

-

P (Programme mode): When completing tuning, the broadcasting stations in your area have been

assigned to position numbers from P00 to P99. You can select a channel by entering the position

number in this mode.

-

C (Air channel mode): You can select a channel by entering the assigned number to each air

broadcasting station in this mode.

-

S (Cable channel mode): You can select a channel by entering the assigned number for each cable

channel in this mode.

Channel

Auto Store

Manual Store ►

Full Guide

Mini Guide

Default Guide : Mini Guide

Channel List

Channel Mode : Added Channels

Child Lock : On

Fine Tune

Manual Store

178750 KHz

Frequency

8 MHz

Bandwidth

5

Channel

Return

Search

AdjustMove

Manual Store

Return

AdjustMove

AUTO

Colour System

BG

Sound System

1

Programme

40 MHz

Search

?

Store

C

--

Channel

Auto Store

Manual Store

Full Guide

Mini Guide

Default Guide : Mini Guide

Channel List

Channel Mode : Added Channels

Child Lock : On

Fine Tune

Channel

Digital Channel

Analogue Channel

English - 16

Viewing the EPG (Electronic Programme Guide) Information

The EPG (Electronic Programme Guide) information is provided by the broadcasters. Programme

entries may appear blank or out of date as a result of the information broadcast on a given

channel. The display will dynamically update as soon as new information becomes available.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

3 Press the ▲ or ▼ button to select Full Guide, Mini Guide or

Default Guide then press the ENTER button.

 Full Guide

For the six channels indicated in the left-hand column, displays

the Current programme and the Next programme information.

¯

One hours of programme information is displayed

which may be scrolled forwards or backwards in time.

 Mini Guide

The information of each program is displayed by each line

on the current channel Mini Guide screen from the current

program onwards according to the program starting time order.

▲/▼/◄/►,

(ENTER)

Select a programme by pressing the

▲/▼/◄/► button.

If the next progrmme is selected,

it is scheduled with the clock icon

displayed. If the

ENTER button is

pressed again, press the ▲/▼/◄/►

button to select

Cancel Schedules,

the scheduling is canceled with the

clock icon gone.

For details about scheduling

programmes, refer to the section.

RED

Toggle between the

Mini Guide or

Full Guide.

GREEN

Full Guide: Scroll backwards quickly

(24 hours).

Mini Guide: Display next page quickly.

YELLOW

Full Guide: Scroll forwards quickly

(24 hours).

Mini Guide: Display previous page

quickly.

BLUE Exit the guide.

INFO

INFO button for the detailed

information. Channel Number,

Running Time, Status Bar, Parental

Level, Video Quality Information

(HD/SD), Sound Modes, Subtitle or

Teletext, languages of Subtitle or

Teletext and brief summary of the

highlighted programme are included

on the detailed information. “…” will

be appeared if the summary is long.

 Default Guide: Mini Guide/Full Guide

Press the ▲ or ▼ button to select Mini Guide or Full

Guide. Press the ENTER button. The selected guide menu

is displayed.

¯

You can also display the guide menu simply by

pressing the

GUIDE button.

Channel

Auto Store

Manual Store

Full Guide

Mini Guide

Default Guide : Mini Guide

Channel List

Channel Mode : Added Channels

Child Lock : On

Fine Tune

Signal Information

Channel

Manual Store

Full Guide

Mini Guide

Default Guide : Mini Guide

Channel List

Channel Mode : Added Channels

Child Lock : On

Fine Tune

Signal Information

LNA : On

Full Guide

Mini Guide

Watch

Exit

DTV 805 BBCi

BBCi

18:00~0:00

BBCi-featuring news, sport, weather and TV..

18:08 Fri 5 Aug

Today 12:00 - 13:00 13:00 - 14:00

▲

801 BBC NEWS 24 BBC Ne.. BBC News

802 BBC ONE BBC Ne.. Departure Lounge

803 BBC THREE

This is BBC THREE

The 7 O’..

804 BBC THREE

This Weakest L..

Tsunami..

805 BBCi

BBCi

▼

806 Canal 7

No Information

INFO

information

+24 Hours

Full Guide Exit

Mini Guide DTV 801 BBC NEWS 24

18:00 BBC News

18:30 Sportsday

19:00 BBC News

Watch

INFO

information

Mini Guide

Default Guide

: Mini GuideMini Guide

Channel List

Channel Mode : Added Channels

Child Lock : On

Fine Tune

Signal Information

LNA : On

Channel

Mini Guide

Full Guide

English - 17

Viewing All Channels

Show all currently available channels. To use the Channel List

function, first run Auto Program.

1 Press the MENU button.

Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

Press the ▲ or ▼ button to select Channel List, then press

the ENTER button.

2 Press the ◄ button to select Added Channels.

3 Press the ▲ or ▼ button to select All Channels, then press

the ENTER button. Shows all currently available channels.

4 Press the ▲ or ▼ button to select a channel to view, then

press the ENTER button.

Press the CH LIST button on the remote control to bring up

the channel lists.

Using the Color buttons on the Remote with the Channel List

• Red (Channel Type): Toggle between your “TV”, “Radio”,

“Data/Other” and “All”.

• Green (Zoom): Enlarges or shrinks a channel number.

• Yellow (Select): Selects multiple channel lists.

•

(Option): Displays the “Delete”(or “Add”), “Add to

Favourite”(or “Delete from Favourite”), “Lock”,

“Timer Viewing”, “Edit Channel Name”, “Sort”,

“Edit Channel Number”, “Select All”, “Deselect

All” or “Auto Store” menu. (The Options menus

may differ depending on the situation.)

¯

A gray-colored channel indicates the channel has been deleted. The Add menu only appears for

deleted channels.

¯

A channel marked with ♥ mark means the channel has been set as a Favourite.

The Delete from Favourite menu only appears for channels with the ♥ mark.

Added Channels All Channels

Channel

Mini Guide

Default Guide :Mini Guide

Channel List

Channel Mode : Added Channels

Child Lock : On

Fine Tune

Signal Information

LNA : Off

824 UKTV Gold

825 UKTV style

1 C --

2 C --

3 C --

4 C --

5 C --

6 C --

7 C --

8 C --

824 UKTV Gold

825 UKTV style

1 C --

2 C --

3 C --

4 C --

5 C --

6 C --

7 C --

8 C --

All

Channel Type

Zoom

Select Option

All

Channel Type

Zoom

Select Option

English - 18

Erasing and Adding Channels

You can delete or add a channel to display the channels

you want.

1 Press the MENU button.

Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

Press the ▲ or ▼ button to select Channel List, then

press the ENTER button.

2 Press the ◄ button to select Added Channels.

3 Press the ▲ or ▼ button to select All Channels.

Shows all currently available channels. Press the ENTER

button.

4 Press the ▲ or ▼ button to select a channel to delete, then

press the TOOLS button.

5 Press the ENTER button to select Delete.

All deleted channels will be shown on All Channels menu.

6 Press the EXIT button to exit.

¯

You can also add a channel to the All Channels menu

in the same manner.

¯

A channel must be deleted before it can be added

back to the Added Channels list.

¯

To Add (Restore) a channel back to the Added

Channel List, follow steps 1-3 above, press the ▲ or

▼ button to select a channel to add, the press the

TOOLS button. Press the ENTER button to select Add.

¯

Press the CH LIST button on the remote control to

bring up the channel lists.

Channel

Mini Guide

Default Guide : Mini Guide

Channel List

Channel Mode : Added Channels

Child Lock :On

Fine Tune

Signal Information

LNA : Off

824 UKTV Gold

825 UKTV style

1 C --

2 C --

3 C --

4 C --

5 C --

6 C --

7 C --

8 C --

Added Channels

824 UKTV Gold

825 UKTV style

1 C --

2 C --

3 C --

4 C --

5 C --

6 C --

7 C --

8 C --

All Channels

824 UKTV Gold

825 UKTV style

1 C --

2 C --

3 C --

4 C --

5 C --

6 C --

7 C --

8 C --

Added Channels

Delete

Add to Favourite

Timer Viewing

Edit Channel Name

Sort

Select All

▼

All

Channel Type

Zoom

Select Option

All

Channel Type

Zoom

Select Option

All

Channel Type

Zoom

Select Option

English - 19

Setting Your Favourite Channels

You can set channels you watch frequently as Favourite.

1 Press the MENU button.

Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

Press the ▲ or ▼ button to select Channel List, then

press the ENTER button.

2 Press the ◄ button to select Added Channels.

3 Press the ▲ or ▼ button to select All Channels, then

press the ENTER button.

¯

Shows all currently available channels.

4 Press the ▲ or ▼ button to select a channel as a favourite

channel.

¯

Adding multiple channels to Favourite.

Press the ▲ or ▼ button to select the desired channel

in the channel list. Then press the yellow button.

Repeat the above operation to select multiple

channels. The  mark appears to the left of the

selected channels.

5 Press the TOOLS button.

6 Press the ▲ or ▼ button to select Add to Favourite, then

press the ENTER button.

The “♥” symbol will be displayed and the channel will be set

as a favourite.

7 To cancel your favourite channel selection, press the

TOOLS button when a favourite channel is selected. Press

the ▲ or ▼ button to select Delete from Favourite, then

press the ENTER button. The channel is deleted from

Favourites and the “♥” mark disappears.

Press the EXIT button to exit.

¯

You can also Add or Delete a channel from Favourite in the Added Channels menu in the same

manner.

¯

All favourite channels will be shown on Favourite menu.

¯

Press the CH LIST button on the remote control to bring up the channel lists.

824 UKTV Gold

825 UKTV style

1 C --

2 C --

3 C --

4 C --

5 C --

6 C --

7 C --

8 C --

All Channels

Delete

Add to Favourite

Timer Viewing

Edit Channel Name

Sort

Select All

▼

Channel

Mini Guide

Default Guide : Mini Guide

Channel List

Channel Mode : Added Channels

Child Lock : On

Fine Tune

Signal Information

LNA : Off

All

Channel Type

Zoom

Select Option

English - 20

Reserving a Program (Time Viewing)

If you reserve a program you want to watch, the channel is

automatically switched to the reserved channel in the Channel

List; even when you are watching another channel.

To reserve a program, set the current time ﬁ rst. See pages 35.

Reserved chanels can only be set if they are in the Channel List

(See page 17).

1 Press the MENU button.

Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

Press the ▲ or ▼ button to select Channel List, then

press the ENTER button.

2 Press the ▲ or ▼ button to select a channel, then press

the TOOLS button.

3 Press the ▲ or ▼ button to select Timer Viewing, then

press the ENTER button.

The Reserve a Program (Timer Viewing) screen appears.

4 Press the ▲/▼/◄/► buttons to reserve a program and

then press the ENTER button.

Reserving a program has been completed.

Press the EXIT button to exit.

¯

You can also reserve a program in the All Channels or

Favourites menus using the same procedures.

¯

For information on how to confirm a viewing

reservation, refer to page 21. Only memorized

channels can be reserved.

¯

You can set the channel, month, day, year, hour and

minute directly by pressing the number buttons on the

remote control.

Press the CH LIST button on the remote control to bring

up the channel lists.

Digital Program Guide and Viewing Reservation

When a digital channel is selected, and you press the ► button,

the Program Guide for the channel appears. You can reserve a

program according to the procedures described above.

: A program currently being broadcast.

: A reserved program.

Continued...

Channel

Mini Guide

Default Guide :Mini Guide

Channel List

Channel Mode : Added Channels

Child Lock : On

Fine Tune

Signal Information

LNA : Off

Timer Viewing

Antenna Channel Repeat

DTV

1 Once

Date

01-01-2008

Start Time

10:09

Enter ReturnMove Adjust

824 UKTV Gold

825 UKTV style

1 C --

2 C --

3 C --

4 C --

5 C --

6 C --

7 C --

8 C --

Added Channels

Air

Channel Type

Zoom

Select Option

Delete

Delete from Favourite

Timer Viewing

Edit Channel Name

Sort

Select All

▼

824 UKTV Gold

825 UKTV style

1 C --

2 C --

3 C --

4 C --

5 C --

6 C --

7 C --

8 C --

Added Channels

Air

Zoom

Option

Watch

1/22/2008

12:47 2.0

3:54 HD 1 99

6:44 HD 1 100

7:49 HD

8:59 +

10:08

10:37

La page charge ...

Samsung PS50A566 Manuel utilisateur

Samsung PS50A566 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents