Simplicity 2185020 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur
Not for
Reproduction
80024087USCN
A
Not for
Reproduction
Manual Contents:
Operator Safety.....................................................................2
Features and Controls..........................................................7
Operation...............................................................................8
Maintenance.........................................................................14
Troubleshooting..................................................................26
Warranties............................................................................27
Slope Guide.........................................................................30
Specifications......................................................................31
The images in this document are representative, and are meant
to complement the instructional copy they accompany. Your
unit may vary from the images displayed.
LEFT
and
RIGHT
are
as seen from the operator's position.
Thank you for purchasing this quality-built Snapper Walkbehind
Mower. We’re pleased that you’ve placed your confidence in
the Snapper brand. When operated and maintained according
to the manuals, your Snapper product will provide many years
of dependable service.
The manuals contain safety information to make you aware of
the hazards and risks associated with the unit and how to avoid
them. This Walkbehind Mower was designed to be used as
described in operator's manual and is not intended for any other
purpose. It is important that you read and understand the
instructions thoroughly before attempting to start or operate this
equipment. Save these original instructions for future reference.
This product requires final assembly before use. Refer to the
setup guide for instructions on final assembly procedures. Follow
the instructions completely.
Operator Safety
Safety Definitions
For your safety, the safety of others, and to protect the
performance of equipment, follow the precautions listed
throughout the manual before operation, during operation, and
during maintenance procedures.
indicates a potential personal injury hazard.
DANGER
indicates a hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING
indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
NOTICE
indicates a situation which can cause damage to the equipment,
personal property and/or the environment, or cause the
equipment to operate improperly.
Safety Symbol Definitions
The following safety symbols may be found on the unit.
Read the operator’s manual before attempting to operate the
mower.
Mow across slopes, not up or down.
To avoid injury to others, do not mow when others, especially
children, are around.
To reduce the potential for fire, wait at least 2 minutes before
refueling.
To avoid serious injury or death, keep hands and feet away from
the mower deck at all times during operation.
To avoid injury from thrown objects, do not operate the mower
unless all mulching, discharge, or bagging components are in their
proper place.
California Spark Arrester Warning
WARNING
It is a violation of California Public Resource Code, Section
4442, to use or operate the engine on any forest-covered,
brush-covered, or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in Section
4442, maintained in effective working order. Other states or
federal jurisdictions may have similar laws. Contact the original
equipment manufacturer, retailer, or dealer to obtain a spark
arrester designed for the exhaust system installed on this
engine.
WARNING
Battery posts, terminals, and related accessories contain
lead and lead compounds, chemicals known to the State
of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
2 www.snapper.com
Not for
Reproduction
WARNING
U.S.A. Models: The engine exhaust from this product
contains chemicals known to the State of California to
cause cancer, birth defects, or other reproductive harm.
Operating Safety
Power equipment is only as safe as the operator. If it is misused,
or not properly maintained, it can be dangerous! Remember,
you are responsible for your safety and that of those around
you.
Use common sense, and think through what you are doing. If
you are not sure that the task you are about to perform can be
safely done with the equipment you have chosen, ask a
professional: contact your local authorized dealer.
Read the Manual
The operator’s manual contains important safety information
you need to be aware of BEFORE you operate your unit as well
as DURING operation.
Safe operating techniques, an explanation of the product’s
features and controls, and maintenance information is included
to help you get the most out of your equipment investment.
Be sure to completely read the Safety Rules and Information
found on the following pages. Also completely read the
Operation section.
Children
Tragic accidents can occur with children. Do not allow them
anywhere near the area of operation. Children are often attracted
to the unit and mowing activity. Never assume that children will
remain where you last saw them. If there is a risk that children
may enter the area where you are mowing, have another
responsible adult watch them.
Slope Operation
3.5 ft
(1,5 m)
20.0 ft
(6,0 m)
You could be seriously injured or even killed if you use this unit
on too steep an incline. Using the unit on a slope that is too
steep or where you don’t have adequate footing or traction can
cause you to lose control or slip and fall.
You should not operate on inclines with a slope greater than 10
degrees, which is a 3.5 ft (1,5 m) rise over 20.0 ft (6,0 m).
Always mow across slopes, never up and down.
Also note that the surface you are mowing can greatly impact
control. Wet grass or leaves can seriously affect your footing
and traction on a slope.
If you feel about operating the unit on an incline, don’t do it. It’s
not worth the risk.
Moving Parts
This equipment has moving parts that can injure you or someone
else. However, if you stand behind the handle properly and
follow all the rules in this book, the unit is safe to operate.
The mower has a spinning mower blade that can amputate
hands and feet. Do not allow anyone near the equipment while
it is running!
3
Not for
Reproduction
To help you, the operator, use this equipment safely, it is
equipped with an operator present safety system. Do NOT
attempt to alter or bypass the system. See your dealer
immediately if the system does not pass all the safety interlock
system tests found in this manual.
Thrown Objects
This unit has a spinning mower blade. This blade can pick up
and throw debris that could seriously injure a bystander. Be
sure to clean up the area to be mowed BEFORE you start
mowing.
Do not operate this unit without the entire grass catcher or
discharge guard (deflector) in place.
Also, do not allow anyone in the area while the unit is running!
If someone does enter the area, turn the unit off immediately
until they leave.
Debris Accumulation
Accumulation of grass and debris can result in a fire. Be sure
to clean any accumulation of grass and debris with a brush or
compressed air, before and after operation.
Fuel and Maintenance
Gasoline is extremely flammable. Its vapors are also extremely
flammable and can travel to distant ignition sources. Gasoline
must only be used as a fuel, not as a solvent or cleaner. It should
never be stored any place where its vapors can build up or travel
to an ignition source like a pilot light. Fuel belongs in an
approved, plastic, sealed gas can, or in the tractor fuel tank with
the cap securely closed. Spilled fuel needs to be cleaned up
immediately.
Proper maintenance is critical to the safety and performance of
your unit. Be sure to perform the maintenance procedures listed
in this manual, especially periodically testing the safety system.
General Safety Messages
WARNING
This powerful cutting machine is capable of amputating hands
and feet and can throw objects that can cause injury and
damage! Failure to comply with the following SAFETY
instructions could result in serious injury or death to the
operator or other persons. The owner of the machine must
understand these instructions and must allow only persons
who understand these instructions to operate machine. Each
person operating the machine must be of sound mind and
body and must not be under the influence of any substance,
which might impair vision, dexterity or judgment.
WARNING
Poisonous Gas Hazard
Engine exhaust contains carbon monoxide, a poisonous gas
that could kill you in minutes. You CANNOT see it, smell it,
or taste it. Even if you do not smell exhaust fumes, you could
still be exposed to carbon monoxide gas. If you start to feel
sick, dizzy, or weak while using this product, shut it off and
get to fresh air RIGHT AWAY. See a doctor. You may have
carbon monoxide poisoning.
Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
Install battery-operated carbon monoxide alarms or plug-in
carbon monoxide alarms with battery back-up according
to the manufacturer’s instructions. Smoke alarms cannot
detect carbon monoxide gas.
DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other
partially-enclosed spaces even if using fans or opening
doors and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut off.
ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
Protection For Children
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the machine
and the mowing activity. Never assume that children will remain
where you last saw them.
1. KEEP children out of the mowing area and under the
watchful care of a responsible adult other than the operator.
2. DO NOT allow children in yard when machine is operated
and turn machine OFF if anyone enters the area.
3. DO NOT allow pre-teenage children to operate machine.
4 www.snapper.com
Not for
Reproduction
4. ALLOW only responsible adults & teenagers with mature
judgment under close adult supervision to operate machine.
5. DO NOT pull mower backwards unless absolutely
necessary. LOOK and SEE behind and down for children,
pets and hazards before and while backing.
6. USE EXTRA CARE when approaching blind corners,
shrubs, trees, or other objects that may obscure vision.
Slope Operation
1. Slopes are a major factor related to slip and fall accidents,
which can result in severe injury. All slopes require extra
caution. If you feel uneasy on a slope, DO NOT mow it.
2. Mow across slopes, never up-and-down. Exercise extreme
CAUTION when changing directions on slopes. DO NOT
mow steep slopes or other areas where stability or traction
is in doubt. Refer to the Slope Guide at the back of this
manual.
3. Use extra care with grass catchers or other attachments;
these affect the handling and the stability of the machine.
Preparation
1. Read, understand, and follow instructions and warnings in
this manual and on the mower, engine and attachments.
Know the controls and the proper use of the mower before
starting.
2. Only mature, responsible persons shall operate the machine
and only after proper instruction.
3. Data indicates that operators age 60 and above, are
involved in a large percentage of mower-related injuries.
These operators should evaluate their ability to operate the
mower safely enough to protect themselves and others from
serious injury.
4. Handle fuel with extra care. Fuels are flammable and vapors
are explosive. Use only an approved fuel container. DO
NOT remove fuel cap or add fuel with engine running. Add
fuel outdoors only with engine stopped and cool. Clean
spilled fuel and oil from machine. DO NOT smoke.
5. Check the area to be mowed and remove all objects such
as toys, wire, rocks, limbs and other objects that could cause
injury if thrown by blade or interfere with mowing. Also note
the location of holes, stumps, and other possible hazards.
6. Keep people and pets out of the mowing area. Immediately,
STOP Blade, Stop engine and Stop mower if anyone enters
the area.
7. Check shields, deflectors, switches, blade controls and
other safety devices frequently for proper operation and
location.
8. Make sure all safety decals are clearly legible. Replace if
damaged.
9. Protect yourself when mowing and wear safety glasses,
long pants and substantial footwear. DO NOT mow
barefooted or with sandals.
10. Know how to STOP blade and engine quickly in preparation
for emergencies.
11. Use extra care when loading or unloading the machine into
a trailer or truck.
12. Check grass catcher components frequently for signs of
wear or deterioration and replace as needed to prevent
injury from thrown objects going through weak or torn spots.
Safe Handling Of Gasoline
To avoid personal injury or property damage, use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive.
1. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
2. Use only an approved fuel container.
3. DO NOT remove fuel cap or add fuel with the engine
running. Allow the engine to cool before refueling.
4. DO NOT refuel the machine indoors.
5. DO NOT store the machine or fuel container inside where
there is an open flame, spark or pilot light such as on a
water heater or other appliances.
6. DO NOT fill fuel containers inside a vehicle or on a truck or
trailer bed with a plastic liner. Always place the containers
on the ground away from the vehicle before filling.
7. Remove gas-powered equipment from the vehicle or trailer
and refuel it on the ground. If this is not possible, then refuel
equipment using a portable container, rather than a gasoline
dispenser nozzle.
8. DO NOT start gas powered equipment in enclosed vehicles
or trailers.
9. Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete. DO
NOT use a nozzle lock-open device.
10. If fuel is spilled on clothing, change clothing immediately.
11. DO NOT overfill a fuel tank. Replace fuel cap and tighten
securely.
Operation
1. DO NOT put hands or feet near or under rotating parts.
Keep clear of discharge area while engine is running.
2. STOP engine when crossing gravel drives, walks, or roads,
and under any conditions where thrown objects might be a
hazard.
3. Mow only in daylight or good artificial light.
4. DO NOT operate mower while under the influence of alcohol
or drugs.
5. After striking a foreign object or if mower vibrates
abnormally, STOP the engine, disconnect and secure spark
plug wire. Inspect the mower for any damage and repair
the damage before starting.
6. DO NOT mow near drop offs, ditches or embankments.
Operator could lose footing or balance.
5
Not for
Reproduction
7. STAY ALERT for holes and other hidden hazards. Tall grass
can hide obstacles. Keep away from ditches, washouts,
culverts, fences and protruding objects.
8. DO NOT mow on wet grass. Always be sure of your footing.
Keep a firm hold on the handle and walk, never run. Slipping
could cause injury.
9. ALWAYS stay behind handle when engine (motor) is
running.
10. DO NOT leave the machine with the engine running. STOP
BLADE and STOP ENGINE before leaving the operators
position for any reason.
11. Before cleaning, repairing or inspecting make certain engine,
blade and all moving parts have STOPPED. Disconnect
and secure spark plug wire away from plug to prevent
accidental starting.
12. STOP engine and wait until the blade comes to complete
STOP before removing grass bag and/or clearing grass.
13. DO NOT operate mower without the entire grass catcher,
rear guard, or other safety devices in place and working.
DO NOT point discharge at people, passing cars, windows
or doors.
14. DO NOT discharge material against a wall or obstruction.
Material may ricochet back towards the operator.
15. Slow down before turning.
16. Watch out for traffic when near or crossing roadways.
17. DO NOT operate engine in enclosed areas. Engine exhaust
gases contain carbon monoxide, a deadly poison.
18. Only use accessories approved by the manufacturer. See
manufacturer’s instructions for proper operation and
installation of accessories.
Maintenance And Storage
1. DO NOT store mower or fuel container inside where fumes
may reach an open flame, spark or pilot light such as in a
water heater, furnace, clothes dryer or other gas appliance.
Allow engine to cool before storing machine in an enclosure.
Store fuel container out of reach of children in a well
ventilated, unoccupied building.
2. Keep mower and engine free of grass, leaves or excess
grease to reduce fire hazard and engine overheating.
3. When draining fuel tank, drain fuel into an approved
container outdoors and away from open flame.
4. Keep all bolts, especially blade bolts, nuts and screws
properly tight. Check that all cotter pins are in proper
position.
5. Always provide adequate ventilation when running engine.
Engine exhaust gases contain carbon monoxide, a deadly
poison.
6. Service engine and make adjustments only when engine
is stopped. Removed spark plug wire from spark plug and
secure wire away from spark plug to prevent accidental
starting.
7. DO NOT change engine governor speed settings or
overspeed engine.
8. Check grass bag assembly frequently for wear or
deterioration to avoid thrown objects and exposure to
moving parts. Replace with new bag if loose seams or tears
are evident. Replace slider or bag adapter if broken or
cracked.
9. Mower blades are sharp and can cut. Wrap the blades or
wear heavy leather gloves and use CAUTION when
handling them.
10. DO NOT test for spark by grounding spark plug next to
spark plug hole; spark plug could ignite gas exiting engine.
11. Have machine serviced by an authorized dealer at least
once a year and have the dealer install any new safety
devices.
12. Use only factory authorized replacement parts or like parts
when making repairs.
Safety and Operation Decals
Reading this manual and the safety instructions it contains will
provide the basic knowledge necessary to operate this mower
safely and effectively. However, several safety and operation
decals have also been placed on the mower as a reminder of
this important information during operation.
The decals noted below are located on the mower. The safety
warnings and operation instructions they contain should be
carefully read, understood, and followed. Not following these
important warnings and instructions can result in serious bodily
injury or death.
If any of these decals are lost or damaged, replace them
immediately. Contact your dealer for replacement decals.
Compare Figure 1 with the table following.
6 www.snapper.com
Not for
Reproduction
1
Drive Control
Squeeze drive
control against
handle to
engage wheel
drive.
A
OPC (Blade Control)
Squeeze blade
control to start
and run engine
and blade.
Release blade
control to stop
engine and
blade.
B
Ground Speed
Control
Move ground
speed control
toward Fast
(Rabbit) to
increase ground
speed.
Move ground
speed control
toward Slow
(Turtle) to
decrease ground
speed.
C
WARNING: Spark
Arrestor may be
required.
D
WARNING: Avoid
Serious Injury or
Death
E
DANGER: Keep
Hands and Feet
Away.
F
DANGER: Amputation
and Thrown Object
Hazard.
G
DANGER: Amputation
and Thrown Object
Hazard.
G
Engine Speed Control
Move engine
speed control in
direction
indicated to
increase or
decrease engine
speed.
H
Features and Controls
Note:
The figures and illustrations in this manual are provided
for reference only and may differ from your specific model.
Contact your dealer if you have questions.
Compare Figure 2 with the table following.
7
Not for
Reproduction
2
Mulching CoverA
Rear Height Adjustment Latch (2)B
Oil Fill Cap and DipstickC
Rope Start HandleD
Engine Speed ControlE
Drive ControlF
Blade ControlG
Ground Speed ControlH
Fuel Filler CapI
Front Height Adjustment Latch (2)J
Operation
Before Starting
1. Check the guards, deflectors, grass bag, and covers to
make sure all are in place and securely tightened.
2. Check the blade control (A, Figure 3), drive control (B), and
ground speed control (C) to insure they work freely.
3
3. Check the cutting height. Adjust to the desired height. See
Cutting Height Adjustment
.
4. Check the engine oil:
Make sure the mower is on a level surface.
Clean the oil fill area of any debris.
Remove the dipstick (A, Figure 4) and wipe with a clean
cloth.
Insert and tighten the dipstick.
Remove the dipstick and check the oil level. It should
be at the top of the full indicator (B) on the dipstick.
If low, add oil slowly into the engine oil fill. See
Oil
Recommendations
. Do not overfill. After adding oil,
wait one minute and recheck the oil level.
Replace and tighten the dipstick.
4
5. Add fuel to the tank:
Make sure the mower is outside, where fumes can
safely dissipate.
Remove the fuel fill cap (C, Figure 4).
8 www.snapper.com
Not for
Reproduction
Fill the tank with fuel. See
Fuel Recommendations
.
To allow for expansion of the fuel, do not fill above the
bottom of the filler neck (D).
Reinstall the fuel fill cap.
6. Clean the exterior surfaces of the cutting deck and engine
of any accumulation of spilled fuel, dirt, grass, oil, etc. Keep
the engine air intake screen and cooling fins clear at all
times.
7. Charge the battery. See
Charging the Battery
.
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty Certified
oils for best performance. Other high-quality detergent oils are
acceptable if classified for service SF, SG, SH, SJ or higher.
Do not use special additives.
Outdoor temperatures determine the proper oil viscosity for the
engine. Use the chart to select the best viscosity for the outdoor
temperature range expected.
SAE 30 - Below 40°F (4°C) the use of SAE 30 will result in hard
starting.
A.
10W-30 - Above 80°F (27°C) the use of 10W-30 may cause
increased oil consumption. Check oil level more frequently.
B.
Synthetic 5W-30C.
5W-30D.
Fuel Recommendations
Fuel must meet these requirements:
Clean, fresh, unleaded gasoline.
A minimum of 87 octane / 87 AKI (91 RON). For high altitude
use, see below.
Gasoline with up to 10% ethanol (gasohol) is acceptable.
NOTICE
Do not use unapproved gasolines, such as E15
and E85. Do not mix oil in gasoline or modify the engine to
run on alternate fuels. Use of unapproved fuels will cause
damage to engine components, which will not be covered
under warranty.
To protect the fuel system from gum formation, mix a fuel
stabilizer into the fuel. See Storage. All fuel is not the same. If
starting or performance problems occur, change fuel providers
or change brands. This engine is certified to operate on gasoline.
The emissions control system for this engine is EM (Engine
Modifications).
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum 85
octane/85 AKI (89 RON) gasoline is acceptable.
For carbureted engines, high altitude adjustment is required to
maintain performance. Operation without this adjustment will
cause decreased performance, increased fuel consumption,
and increased emissions. Contact a Briggs & Stratton Authorized
Service Dealer for high altitude adjustment information.
Operation of the engine at altitudes below 2,500 feet (762
meters) with the high altitude adjustment is not recommended.
For Electronic Fuel Injection (EFI) engines, no high altitude
adjustment is necessary.
Starting the Mower
WARNING
Poisonous Gas Hazard
Engine exhaust contains carbon monoxide, a poisonous gas
that could kill you in minutes. You CANNOT see it, smell it,
or taste it. Even if you do not smell exhaust fumes, you could
still be exposed to carbon monoxide gas. If you start to feel
sick, dizzy, or weak while using this product, shut it off and
get to fresh air RIGHT AWAY. See a doctor. You may have
carbon monoxide poisoning.
Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
Install battery-operated carbon monoxide alarms or plug-in
carbon monoxide alarms with battery back-up according
to the manufacturer’s instructions. Smoke alarms cannot
detect carbon monoxide gas.
DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other
partially-enclosed spaces even if using fans or opening
doors and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut off.
ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
The engine on your mower is equipped with the Briggs &
Stratton Ready Start™ System. This features a
temperature-controlled automatic choke. No additional steps
are required to start a cold engine.
1. Move the engine speed control (A, Figure 5, if equipped)
to the fast (‘Rabbit’) position.
2. Squeeze the blade control (B) against the handle.
3. Start the mower:
Manual Start Models: Pull the rope start handle (C) to
crank the engine.
Electric Start Models: Insert the key (D) into the electric
start switch. Turn the key to crank the engine. Use short
9
Not for
Reproduction
starting cycles, five seconds maximum, and wait 1
minute between starting cycles.
4. To stop the engine (and blade), release the blade control.
5. After the engine starts, allow a brief warm-up until the engine
runs smooth before beginning mower operation.
5
Propelling the Mower
1. Start the mower.
2. Move the ground speed control (A, Figure 6) to the desired
speed position.
3. Squeeze the wheel drive control (B) against the handle to
engage the wheel drive and propel the mower forward.
Forward speed can be adjusted while the mower is moving
by changing the position of the ground speed control.
6
Stopping the Mower
1. Stop forward motion of the mower by releasing the wheel
drive control.
2. Stop the engine and blade by releasing the blade control.
3. Electric Start Models: Remove the key from the electric start
switch.
Handle Height Adjustment
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
The height of the mower handle can be adjusted as follows:
1. Loosen the lower nuts (A, Figure 7) on each lower handle.
2. Move the handle assembly (B) up or down until the desired
position is achieved.
3. Tighten the lower nuts on each lower handle to maintain
the desired position.
7
10 www.snapper.com
Not for
Reproduction
Cutting Height Adjustment
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
1. Pull the height adjusting latch (A, Figure 8) outward and
move to the desired cutting height.
8
2. Set all wheels at the same cutting height. The highest cutting
position is Notch 7 (Figure 9). The lowest cutting position
is Notch 1.
9
Mulching Operation
For best mulching results, cut up to a maximum of 1/3 of grass
blade length and recycle ONLY when grass is dry.
1. Set all wheels in the highest cutting position (Notch 7). See
Cutting Height Adjustment
.
2. Move the engine speed control to the fast (Rabbit) position.
3. Move the ground speed control to the slowest speed setting.
4. Proceed mowing slowly. If the grass is very dense, lower
each rear wheel latch one notch lower than the front wheel
latches to improve mulching performance.
Note:
The mulching cover should remain on the machine at all
times, unless alternate discharge operations are desired, such
as side discharging or bagging.
Removing the Mulching Cover
(Optional Accessory on Some Models)
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
1. Remove the knob nuts (A, Figure 10) and internal/ external
tooth lock washers (B) securing the mulching cover (C) to
the mower deck.
2. Remove the cover.
10
11
Not for
Reproduction
Installing the Discharge Deflector
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
1. Remove the mulching cover. See
Mulching Operation
.
2. Install the deflector (A, Figure 11) to the deck in place of
the mulching cover, making sure that:
The front hole (B) on the outside front of the deflector
fits over the stud where the front of the mulching cover
was originally secured;
The slot (C) on top of the deflector slips under the
restraining nut on top of the deck (under the right front
corner of the engine);
The slot (D) on the inside rear of the deflector slips onto
the stud behind the rear of the discharge opening,
where the rear of the mulching cover was originally
secured.
3. Install the internal/external tooth lock washers and knob
nuts onto the studs and tighten securely.
11
WARNING
Thrown Objects Hazard
DO NOT operate without entire Grass Catcher or guard in
place. Grass Catcher components are subject to deterioration
during normal use. Inspect frequently and replace worn or
damaged components immediately.
Installing the Grass Bag Adapter
(Optional Accessory on Some Models)
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
1. Remove the mulching cover. See
Removing the Mulching
Cover
.
2. Install the adapter (A, Figure 12) to the deck in place of the
mulching cover, making sure that:
The front hole (B) on the outside front of the adapter
fits over the stud where the front of the mulching cover
was originally secured;
The slot (C) on top of the adapter slips under the
restraining nut on top of the deck (under the right front
corner of the engine);
The slot (D) on the rear of the adapter slips onto the
stud behind the rear of the discharge opening, where
the rear of the mulching cover was originally secured.
3. Install the internal/external tooth lock washers and knob
nuts onto the studs and tighten securely.
4. Route the recoil rope around the outside of the rope guide
pulley (E).
Note:
The recoil rope may need to be slackened. See
Starting
the Mower
.
12 www.snapper.com
Not for
Reproduction
12
Installing the Mulching Plug
(Optional Accessory on Some Models)
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
1. Install the mulching plug (A, Figure 13) if mulching is desired
after the bag adapter is installed. Install the mulching plug
completely and securely into the bag adapter (B).
2. Install the grass bag as a safeguard and to further secure
the mulching plug.
WARNING
Thrown Objects Hazard
Install the grass bag when using the mulching plug. Failure
to do so may result in personal injury or death.
3. See
Mulching Operation
.
13
Installing the Grass Bag
(Optional Accessory on Some Models)
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
1. Install the grass bag adapter. See
Installing the Grass
Bag Adapter
.
2. Install the grass bag by sliding the connector (A, Figure 14)
over the adapter flange.
3. Attach the grass bag hooks (B) over the middle handle cross
bar.
13
Not for
Reproduction
14
WARNING
Unsafe Operation Hazard
Grass Catcher bags are made of woven fabric, and are subject
to deterioration and wear during normal usage. Check
condition of bag before each use. Immediately replace worn
or damaged catcher bags with only genuine replacement
bags. The grass catcher is optional equipment on some
models.
Charging the Battery
(Optional Accessory on Some Models)
The battery provided with your mower is sealed and
maintenance-free. It requires no special care other than keeping
it properly charged. Use only the charger provided with your
mower when charging the battery.
Charge the battery after each use, and if the battery has been
stored for longer than 30 days. The time required to charge the
battery varies, but typically 16 to 24 hours will be sufficient to
bring the battery to a fully charged condition.
1. Remove the dust cap from the charger jack (A, Figure 15).
2. Plug the battery charger (B) into the charger jack.
3. Plug the charger into a 120-volt wall outlet.
4. Charge the battery for a period of 16 to 24 hours. (Longer
periods will not damage the battery.)
5. Unplug the charger from the wall outlet.
6. Unplug the charger from the charger jack.
7. Replace the dust cap onto the charger jack.
15
WARNING
Explosion Hazard
Avoid Serious Injury and Property Damage.
DO NOT attempt to charge this battery with automotive
or ‘Boost’ chargers.
DO NOT attempt to jump start a mower that has a dead
battery.
Always use the charger supplied with this mower to charge
this battery.
Maintenance
Emissions Control Service
Maintenance, replacement, or repair of the emissions
control devices and systems may be performed by any
off-road engine repair establishment or individual. However,
to obtain "no charge" emissions control service, the work must
be performed by a factory authorized dealer. See the Emissions
Control Statements.
14 www.snapper.com
Not for
Reproduction
Maintenance Chart
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
Laceration Hazard
Wear heavy leather gloves when handling or working
around cutting blades.
Blades are extremely sharp and can cause severe injury.
MOWER
Every 8 Hours or Daily
Check safety interlock system
Clean debris off mower
Every 25 Hours or Annually *
Check mower for loose hardware
See Dealer Annually to
Lubricate mower
Check mower blade **
Check mower blade stopping time
Check drive belt
Clean battery and cables
* Whichever comes first
** Check blade more often in regions with sandy soils or high
dust conditions
ENGINE
First 5 Hours
Change engine oil
Every 8 Hours or Daily
Check engine oil level
Every 25 Hours or Annually *
Clean engine air filter and pre-cleaner (if equipped) **
Every 50 Hours or Annually *
Change engine oil
Replace oil filter (if equipped)
Annually
Replace air filter
Replace pre-cleaner (if equipped)
See Dealer Annually to
Inspect muffler and spark arrester (if equipped)
Replace spark plug
ENGINE
Replace fuel filter (if equipped)
Clean engine air cooling system
* Whichever comes first
** Clean more often in dusty conditions or when airborne debris
is present
Change Engine Oil
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
Laceration Hazard
Wear heavy leather gloves when handling or working
around cutting blades.
Blades are extremely sharp and can cause severe injury.
1. Drain the fuel tank completely.
2. Remove the dipstick (A, Figure 16), then turn the mower
on its side. Allow the oil to drain from the oil fill tube into an
appropriate container. Dispose of used oil properly.
3. Place the mower upright, then fill the engine with engine oil
to the ‘full’ mark on the dipstick. Refer to the section entitled
‘Oil Recommendations’. Do not overfill.
16
15
Not for
Reproduction
NOTICE
Drain the fuel tank before tipping the machine. DO NOT tip
the machine with the carburetor or spark plug down. Oil from
the crankcase will saturate the air filter and cause the engine
to be hard to start or not start at all. If contamination does
occur, the air filter will have to be replaced.
Change Oil Filter
(If Equipped)
1. Drain the oil from the engine. See
Change Engine Oil
.
2. Remove the oil filter (B, Figure 16) and dispose of properly.
3. Before you install the new oil filter, lightly lubricate the oil
filter gasket with fresh, clean oil.
4. Install the oil filter by hand until the gasket contacts the oil
filter adapter, then tighten the oil filter 1/2 to 3/4 turns.
5. Add oil. See
Change Engine Oil
.
6. Start and run the engine. As the engine warms up, check
for oil leaks.
7. Stop the engine and check the oil level. It should be at the
top of the full indicator on the dipstick.
Service Air Filter
WARNING
Fire Hazard
Never start or run the engine with the air cleaner assembly (if
equipped) or the air filter (if equipped) removed.
NOTICE
Do not use pressurized air or solvents to clean the filter.
Pressurized air can damage the filter and solvents will dissolve
the filter.
1. Remove the fastener (A, Figure 17) and the air filter cover
(B).
2. Remove the pre-cleaner (C) and the filter (D).
3. To loosen debris, gently tap the filter on a hard surface. If
the filter is excessively dirty, replace with a new filter.
4. Wash the pre-cleaner in liquid detergent and water. Then
allow it to thoroughly air dry. Do not oil the pre-cleaner.
5. Assemble the dry pre-cleaner to the filter.
6. Install the filter and pre-cleaner into the base (E). Make sure
filter fits securely in the base.
7. Install air filter cover and secure with fastener. Make sure
the fastener is tight.
17
Check Safety Interlock System
1. Start the mower.
2. Release the blade control. The engine must stop within 3
seconds.
WARNING
Unsafe Operation Hazard
If the engine does not stop within 3 seconds, do not use the
mower. Bring the mower to an authorized dealer for service.
Clean Debris Off Mower
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
Laceration Hazard
Wear heavy leather gloves when handling or working
around cutting blades.
Blades are extremely sharp and can cause severe injury.
16 www.snapper.com
Not for
Reproduction
1. Clean dirt and debris from the top of the mower deck.
2. Clean any debris buildup on or around the engine, etc.
While cleaning, check components for wear or damage. Replace
worn or damaged components immediately.
Storage Procedure
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
Laceration Hazard
Wear heavy leather gloves when handling or working
around cutting blades.
Blades are extremely sharp and can cause severe injury.
Prepare the mower for end-of-season storage as follows:
1. Disconnect the spark plug wire and secure away from the
spark plug.
2. Drain the fuel tank and let the engine run until all fuel is out
of the carburetor.
Note:
If using a fuel stabilizer, there is no need to drain the fuel
tank. See
Fuel System
.
3. Use a brush or compressed air to remove loose debris, then
use a damp cloth to wipe down the unit.
4. Tilt the mower up on its rear wheels and inspect the
underside of the deck. (Do not tilt the mower with the spark
plug or carburetor down.) Scrape away stubborn
accumulation of grass with a putty knife and/or wire brush.
5. Lubricate all exposed metal with a light coating of oil to
prevent corrosion.
6. Carefully fold the handles, flexing the control cables to
prevent cable damage.
7. Store the mower in a shed or other dry area, protected from
weather.
Fuel System
Fuel can become stale when stored over 30 days. Stale fuel
causes acid and gum deposits to form in the fuel system or on
essential carburetor parts. To keep fuel fresh, use Briggs &
Stratton Advanced Formula Fuel Treatment & Stabilizer,
available wherever Briggs & Stratton genuine service parts are
sold.
There is no need to drain gasoline from the engine if a fuel
stabilizer is added according to instructions. Run the engine for
two (2) minutes to circulate the stabilizer throughout the fuel
system before storage.
If gasoline in the engine has not been treated with a fuel
stabilizer, it must be drained into an approved container. Run
the engine until it stops from lack of fuel. The use of a fuel
stabilizer in the storage container is recommended to maintain
freshness.
Service
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
Laceration Hazard
Wear heavy leather gloves when handling or working
around cutting blades.
Blades are extremely sharp and can cause severe injury.
Check Grease Level in Transmission
1. Remove the transmission fill plug (A, Figure 18). Roll the
machine forward or backward while looking down into the
plug hole.
2. If liquid grease is not visible on the input gear (the small
gear below the plug hole), add an amount, to cover the
gear, of Snapper “00” grease.
Note:
Snapper “00” grease (Part No. 7029443) is available at
your dealer.
Note:
Do not spill grease or oil onto the surface of the drive disc
(A, Figure 19).
3. Reinstall the transmission plug.
4. Check the grease level after each 25 hours of operation.
17
Not for
Reproduction
18
19
Check Mower Blade
1. Disconnect the spark plug wire and secure the end away
from the plug.
2. Tilt the mower up on its rear wheels for access to the blade
cap screw (A, Figure 20). Do not tilt the mower with the
spark plug or carburetor down.
NOTICE
Drain the fuel tank before tipping the mower. DO NOT tip the
machine with the carburetor or spark plug down. Oil from the
crankcase will saturate the air filter and cause the engine to
be hard to start or not start at all. If contamination does occur,
the air filter will have to be replaced.
3. Check the torque of the blade cap screw. Recommended
torque: 40 lb-ft (54 Nm).
4. Check the blade for sharpness, wear and damage. See
Blade Wear Limits
.
20
Check Engine Drive Belt
Visually check the engine drive belt for cracking, fraying,
severed or exposed belt strands. If worn or damaged,
replace the belt before operating the mower.
Check Transmission Drive Belt
Visually check the poly-v belt for cracking, fraying, severed
or exposed belt strands. If worn or damaged, replace the
belt before operating the mower.
Mower Blade Replacement
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
Laceration Hazard
Wear heavy leather gloves when handling or working
around cutting blades.
Blades are extremely sharp and can cause severe injury.
WARNING
Unsafe Operation Hazard
18 www.snapper.com
Not for
Reproduction
DO NOT use a cutting blade that shows signs of excessive wear
or damage.
Standard Blade Wear Limit
1. Inspect the blade (Figure 21) frequently for signs of
excessive wear or damage:
(A) New blade
(B) Wear limit (notch starts)
(C) Dangerous condition! Do not use on the mower!
Replace with a new blade.
21
Ninja Blade Wear Limit
1. Inspect the blade (Figure 22) frequently for signs of
excessive wear or damage:
(A) New blade
(B) Wear limit (cracks or notches begin to appear on
tip)
(C) Dangerous condition! Do not use on the mower!
Replace with a new blade.
22
Blade Sharpening
1. Disconnect the spark plug wire and secure the end away
from the plug.
2. Tilt the mower up on its rear wheels. Do not tilt the mower
with the spark plug or carburetor down.
NOTICE
Drain the fuel tank before tipping the mower. DO NOT tip the
machine with the carburetor or spark plug down. Oil from the
crankcase will saturate the air filter and cause the engine to
be hard to start or not start at all. If contamination does occur,
the air filter will have to be replaced.
3. Remove the blade (B, Figure 23).
4. Sharpen the blade on a grinding wheel at an angle of 22 to
28 degrees (B, Figure 24). DO NOT sharpen the blade
beyond the original cutting edge (A).
5. Check blade for balance. If necessary, correct balance by
grinding heavy end of blade.
6. Reinstall blade (B, Figure 23). Note the correct assembly
order:
(A) Blade hub
(B) Blade
(C) Blade flange (facing up)
(D) Cone washer (concave side up)
(E) Capscrew
7. Check torque of blade retaining cap screw. Recommended
torque: 40 lb-ft (54 Nm).
19
Not for
Reproduction
23
24
Wheel Drive Control Adjustment
WARNING
Amputation Hazard
DO NOT attempt any maintenance, adjustments or service
with engine and blade running.
STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug.
Burn Hazard
Engine and components are HOT.
Avoid serious burns, allow sufficient time for all
components to cool.
1. The wheel drive control is properly adjusted when there is
1/16” to 1/8” (1.6 - 3.2 mm) clearance (G, Figure 25)
between the inside of the spring hook (E) and the inside of
the clutch cable eye (C) with the wheel drive control
released.
2. To adjust, unhook the upper spring (D) from the cable eye
and rotate the spring in the direction required to extend or
shorten the spring length.
3. Rehook the upper spring to the cable eye and check
clearance. Repeat the procedure if required.
Note:
The vinyl spring cover (B) should be kept over the spring
at all times except for adjustments.
4. If the wheel drive control fails to return quickly to the OFF
position when released, check for binding at the cable
holdings located on the side of the right handle. The upper
clip should be located 2” (5 cm) below the upper knob; the
lower clip should be 4” (10 cm) above the lower knob. The
cable should slide freely with the clips installed at these
locations.
25
20 www.snapper.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100

Simplicity 2185020 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur

dans d''autres langues