Sony XAV-AX5550D Le manuel du propriétaire

XAV-AX5550D

5-010-462-41(1)

AV RECEIVER

Operating Instructions

GB

Mode d’emploi

FR

Bedienungsanleitung

DE

Manual de instrucciones

ES

Gebruiksaanwijzing

NL

Bruksanvisning

SE

To cancel the demonstration (Demo) display, see page 6.

For the connection/installation, see page 10.

Pour annuler la démonstration (Démo), reportez-vous à la

page 6.

Pour le raccordement/l’installation, reportez-vous à la page 10.

Zum Deaktivieren der Demo-Anzeige (Demo) schlagen Sie bitte

auf Seite 6 nach.

Informationen zum Anschluss und zur Installation finden Sie auf

Seite 11.

Para cancelar la pantalla de demostración (Demostración),

consulte la página 6.

Para la conexión/instalación, consulte la página 10.

Om de demonstratie (Demo) te annuleren, zie pagina 7.

Raadpleeg pagina 10 voor meer informatie over de aansluiting/

installatie.

Se sidan 6 för att avbryta demonstrationsvisningen (Demo).

Se sidan 10 för anslutning/installation.

2GB

Warning

Made in Thailand

The nameplate indicating operating voltage, etc., is

located on the bottom of the chassis.

The validity of the CE marking is restricted to only

those countries where it is legally enforced, mainly

in the countries EEA (European Economic Area) and

Switzerland.

WARNING

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified personnel

only.

Hereby, Sony Corporation declares that this

equipment is in compliance with Directive 2014/53/

EU.

The full text of the EU declaration of conformity is

available at the following internet address:

http://www.compliance.sony.de/

Notice for customers: the following

information is only applicable to equipment

sold in countries applying EU Directives

This product has been manufactured by or on

behalf of Sony Corporation.

EU Importer: Sony Europe B.V.

Inquiries to the EU Importer or related to product

compliance in Europe should be sent to the

manufacturer’s authorized representative, Sony

Belgium, bijkantoor van Sony Europe B.V., Da

Vincilaan 7-D1, 1930 Zaventem, Belgium.

Disposal of waste batteries and

electrical and electronic equipment

(applicable in the European Union

and other countries with separate

collection systems)

This symbol on the product, the battery or on the

packaging indicates that the product and the

battery shall not be treated as household waste.

On certain batteries this symbol might be used in

combination with a chemical symbol. The chemical

symbol for lead (Pb) is added if the battery contains

more than 0.004% lead.

By ensuring that these products and batteries are

disposed of correctly, you will help to prevent

potentially negative consequences for the

environment and human health which could be

caused by inappropriate waste handling. The

recycling of the materials will help to conserve

natural resources.

In case of products that for safety, performance or

data integrity reasons require a permanent

connection with an incorporated battery, this

battery should be replaced by qualified service staff

only.

To ensure that the battery and the electrical and

electronic equipment will be treated properly, hand

over these products at end-of-life to the

appropriate collection point for the recycling of

electrical and electronic equipment.

For all other batteries, please view the section on

how to remove the battery from the product safely.

Hand the battery over to the appropriate collection

point for the recycling of waste batteries.

For more detailed information about recycling of

this product or battery, please contact your local

Civic Office, your household waste disposal service

or the shop where you purchased the product or

battery.

Disclaimer regarding services offered by third

parties

Services offered by third parties may be changed,

suspended, or terminated without prior notice.

Sony does not bear any responsibility in these sorts

of situations.

For safety, be sure to install this unit in the

dashboard of the car as the rear side of the unit

becomes hot during use.

For details, see “Connection/Installation”

(page 10).

Warning if your car’s ignition has no ACC

position

Do not install this unit in a car that has no ACC

position. The display of the unit does not turn off

even after turning the ignition off, and this

causes battery drain.

3GB

Caution

IN NO EVENT SHALL SONY BE LIABLE FOR ANY

INCIDENTAL, INDIRECT OR CONSEQUENTIAL

DAMAGES OR OTHER DAMAGES INCLUDING,

WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF

REVENUE, LOSS OF DATA, LOSS OF USE OF THE

PRODUCT OR ANY ASSOCIATED EQUIPMENT,

DOWNTIME, AND PURCHASER’S TIME RELATED TO

OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS

HARDWARE AND/OR ITS SOFTWARE.

Dear customer, this product includes a radio

transmitter.

According to UNECE Regulation no. 10, a vehicle

manufacturers may impose specific conditions for

installation of radio transmitters into vehicles.

Please check your vehicle operation manual or

contact the manufacturer of your vehicle or your

vehicle dealer, before you install this product into

your vehicle.

Emergency calls

This BLUETOOTH car handsfree and the electronic

device connected to the handsfree operate using

radio signals, cellular, and landline networks as well

as user-programmed function, which cannot

guarantee connection under all conditions.

Therefore do not rely solely upon any electronic

device for essential communications (such as

medical emergencies).

On BLUETOOTH communication

• Microwaves emitting from a BLUETOOTH device

may affect the operation of electronic medical

devices. Turn off this unit and other BLUETOOTH

devices in the following locations, as it may cause

an accident.

– where inflammable gas is present, in a hospital,

train, airplane, or petrol station

– near automatic doors or a fire alarm

• This unit supports security capabilities that

comply with the BLUETOOTH standard to provide

a secure connection when the BLUETOOTH

wireless technology is used, but security may not

be enough depending on the setting. Be careful

when communicating using BLUETOOTH wireless

technology.

• We do not take any responsibility for the leakage

of information during BLUETOOTH

communication.

If you have any questions or problems concerning

your unit that are not covered in this manual,

consult your nearest Sony dealer.

Important notice

4GB

Main Unit

The VOL (volume) + button has a tactile dot.

 Display/touch screen

 HOME

Displays the HOME screen (page 5).

ATT (attenuate)

Press and hold for 1 second to attenuate the

sound.

To cancel, press and hold again, or press VOL +.

 VOL (volume) +/–

 Receptor for the remote commander

/ (previous/next)

Functions differently depending on the selected

source:

– Radio/DAB+: select a preset station.

– USB/BT Audio: move to the previous/next file.

Press and hold to:

– Radio: tune into a station automatically

(SEEK+/SEEK–).

– DAB+: select a station (when [Seek By] is set to

[A-Z])/search for a station (when [Seek By] is

set to [Station Gp]).

– USB/BT Audio: fast-reverse/fast-forward.

 OPTION

Displays the OPTION screen (page 5).

VOICE

Press and hold to activate the voice command

function for Apple CarPlay and Android Auto™.

Guide to Parts and Controls

5GB

Screen displays

Playback screen:

HOME screen:

OPTION screen:

 Status indication

 (source option)

Opens the source option menu. The available

items differ depending on the source.

 Application specific area

Displays playback controls/indications or show

the unit’s status. Displayed items differ

depending on the source.

 Clock

Displays the time which are set on the date/time

setting.

 (return to the playback screen)

Switches from the HOME screen to the playback

screen.

 Sources and Settings select keys

Changes the source or make various settings.

Flick to select the setting icon and other icons.

Touch the source icon you want to select.

Lights up when the sound is attenuated.

Lights up when AF (Alternative

Frequencies) is available.

Lights up when the current traffic

information (TA: Traffic Announcement)

is available.

Lights up when a DAB announcement is

available.

Indicates the signal strength status of

the DAB radio.

Lights up when the Bluetooth® signal is

on. Flashes when the connection is in

progress.

Lights up when the audio device is

playable by enabling the A2DP

(Advanced Audio Distribution Profile).

Lights up when handsfree calling is

available by enabling the HFP (Handsfree

Profile).

Indicates the signal strength status of

the connected mobile phone.

Indicates the remaining battery status of

the connected mobile phone.

Android

Auto

Apple

CarPlay

Radio

DAB+ BT Audio Phone

USB port 1 WebLink USB port 2

Rear

Camera

Settings

6GB

 Sound select keys

Changes the sound.

 (standby)

Turns the unit in standby mode (USB charging is

still available). To resume, press any buttons.

 (monitor off)

Turns off the monitor. When the monitor is

turned off, touch any part of the display to turn it

back on.

 (EXTRA BASS)

Changes the EXTRA BASS setting.

 (EQ10/subwoofer)

Changes the EQ10/subwoofer setting.

Pairing with a BLUETOOTH Device

When connecting a BLUETOOTH device for the first

time, mutual registration (called “pairing”) is

required. Pairing enables this unit and other devices

to recognize each other.

1 Press HOME, then touch [Settings] 

[Bluetooth]  [Bluetooth Connection]  [ON]

 [Pairing].

flashes while the unit is in pairing standby

mode.

2 Perform pairing on the BLUETOOTH device

so it detects this unit.

3 Select your model name shown on the

display of the BLUETOOTH device*.

When pairing is made, stays lit.

* If passkey input is required on the BLUETOOTH device,

input [0000].

Connecting Rear View Camera

By connecting the optional rear view camera to the

CAMERA IN terminal, you can display the picture

from the rear view camera. For details, see

“Connection/Installation” (page 10).

To display the picture from the rear view

camera

Press HOME, then touch [Rear Camera].

Canceling the Demonstration

Mode

1 Press HOME, then touch [Settings].

2 Touch [General], then touch [Demo] to set to

[OFF].

3 To exit the setup menu, touch (back)

twice.

Updating the Firmware

To update the firmware, visit the support site on the

back cover, then follow the online instructions.

Note

During the update, do not remove the USB device.

Basic Operations

7GB

Precautions

•Power antenna (aerial) extends automatically.

•When you transfer ownership or dispose of your

car with the unit installed, initialize all the settings

to the factory settings by performing the factory

reset.

• Do not splash liquid onto the unit.

Notes on safety

•Comply with your local traffic rules, laws, and

regulations.

•While driving

– Do not watch or operate the unit, as it may lead

to distraction and cause an accident. Park your

car in a safe place to watch or operate the unit.

– Do not use the setup feature or any other

function which could divert your attention from

the road.

– When backing up your car, be sure to look back

and watch the surroundings carefully for your

safety even if the rear view camera is connected.

Do not depend on the rear view camera

exclusively.

•While operating

– Do not insert your hands, fingers, or foreign

objects into the unit as it may cause injury or

damage to the unit.

– Keep small articles out of the reach of children.

– Be sure to fasten seatbelts to avoid injury in the

event of sudden movement of the car.

Notes on LCD panel

• Do not get the LCD

panel wet or expose it

to liquids. This may

cause a malfunction.

•Do not press down

hard on the LCD panel

as doing so can distort

the picture or cause a

malfunction (i.e., the

picture may become

unclear or the LCD

panel may be damaged).

• Do not touch the panel with objects other than

with your finger as it may damage or break the

LCD panel.

• Clean the LCD panel with a dry soft cloth. Do not

use solvents such as benzine, thinner,

commercially available cleaners, or antistatic

spray.

• Do not use the unit outside the temperature range

0 ºC to 40 ºC (32 ºF to 104 ºF).

• If your car was parked in a cold or hot place, the

picture may not be clear. However, the monitor is

not damaged and the picture will become clear

after the temperature in your car becomes normal.

• Some stationary blue, red, or green dots may

appear on the monitor. These are called “bright

spots” and can happen with any LCD. The LCD

panel is precision-manufactured with more than

99.99% of its segments functional. However, it is

possible that a small percentage (typically 0.01%)

of the segments may not light up properly. This

will not, however, interfere with your viewing.

Notes on the touch screen

• This unit uses a capacitive touch screen. Touch the

screen directly with your fingertip.

• Multi-touch operation is not supported on this

unit.

• Do not touch the screen with sharp objects such

as a needle, pen, or fingernail. Operation with a

stylus is not supported on this unit.

• Touching the screen with a gloved finger may

cause the unit to operate incorrectly or not

respond.

• Do not let any objects contact the touch screen. If

the screen is touched by an object other than your

fingertip, the unit may not respond correctly.

• Since glass material is used for the screen, do not

subject the unit to strong shock. If cracking or

chipping occurs on the screen, do not touch the

damaged part as it may cause injury.

• Keep other electrical devices away from the touch

screen. They may cause the touch screen to

malfunction.

• If there are water droplets on the touch screen, or

if you touch the screen with wet fingertips, the

touch screen may not react correctly.

Additional Information

Preventing an accident

Pictures appear only after you park the car and

set the parking brake.

If the car starts moving during video playback,

the following caution is displayed and you

cannot watch the video.

[Video blocked for your safety.]

Do not operate the unit or watch the monitor

while driving.

8GB

•Compatible iPhone models:

iPhone XS Max, iPhone XS, iPhone XR, iPhone X,

iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone 7,

iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6

Plus, iPhone 6, iPhone 5s

•Use of the Made for Apple badge means that an

accessory has been designed to connect

specifically to the Apple product(s) identified in

the badge, and has been certified by the

developer to meet Apple performance standards.

Apple is not responsible for the operation of this

device or its compliance with safety and

regulatory standards.

Please note that the use of this accessory with an

Apple product may affect wireless performance.

This product contains software that Sony uses

under a licensing agreement with the owner of its

copyright. We are obligated to announce the

contents of the agreement to customers under

requirement by the owner of copyright for the

software.

For details on software licenses, select [Settings] 

[General]  [Open Source Licenses].

Notice on GNU GPL/LGPL applied software

This product contains software that is subject to the

following GNU General Public License (hereinafter

referred to as “GPL”) or GNU Lesser General Public

License (hereinafter referred to as “LGPL”). These

establish that customers have the right to acquire,

modify, and redistribute the source code of said

software in accordance with the terms of the GPL or

LGPL displayed on this unit.

The source code for the above-listed software is

available on the Web.

To download, please access the following URL then

select the model name “XAV-AX5550D.”

URL: http://www.sony.net/Products/Linux/

Please note that Sony cannot answer or respond to

any inquiries regarding the content of the source

code.

If you have any questions or problems concerning

your unit that are not covered in this Operating

Instructions, consult your nearest Sony dealer.

Specifications

Monitor section

Display type: Wide LCD color monitor

Dimensions: 6.95 in/176 mm

System: TFT active matrix

Number of pixels:

1,152,000 pixels (800 × 3 (RGB) × 480)

Color system:

PAL/NTSC automatic select for CAMERA IN

terminal

Radio section

DAB/DAB+

Tuning range: 174.928 MHz – 239.200 MHz

Antenna (aerial) terminal:

External antenna (aerial) connector

FM

Tuning range: 87.5 MHz – 108.0 MHz

Usable sensitivity: 7 dBf

Signal-to-noise ratio: 70 dB (mono)

Separation at 1 kHz: 45 dB

AM

Tuning range: 531 kHz – 1,602 kHz

Sensitivity: 32 µV

USB player section

Interface:

USB port 1 (Hi-speed)

USB port 2 (Full-speed)

Maximum current:

USB port 1: 1.5 A

USB port 2: 500 mA

Wireless communication

Communication System:

BLUETOOTH Standard version 3.0

Output:

BLUETOOTH Standard Power Class 2

(Max. Conducted +1 dBm)

Maximum communication range*

1

:

Line of sight approx. 10 m (33 ft)

Frequency band:

2.4 GHz band (2.4000 GHz – 2.4835 GHz)

Modulation method: FHSS

Compatible BLUETOOTH Profiles*

2

:

A2DP (Advanced Audio Distribution Profile) 1.3

AVRCP (Audio Video Remote Control Profile) 1.3

HFP (Handsfree Profile) 1.6

PBAP (Phone Book Access Profile) 1.1

Corresponding codec: SBC, AAC

About iPhone

Notice on license

9GB

*1 The actual range will vary depending on factors such as

obstacles between devices, magnetic fields around a

microwave oven, static electricity, reception sensitivity,

antenna (aerial)’s performance, operating system,

software application, etc.

*2 BLUETOOTH standard profiles indicate the purpose of

BLUETOOTH communication between devices.

Power amplifier section

Outputs: Speaker outputs

Speaker impedance: 4  – 8 

Maximum power output: 55 W × 4 (at 4 )

General

Power requirements: 12 V DC car battery

(negative ground (earth))

Rated current consumption: 10 A

Dimensions:

Approx. 178 mm × 100 mm × 139 mm

(7

1

/8 in × 4 in × 5

1

/2 in) (w/h/d)

Mounting dimensions:

Approx. 182 mm × 111 mm × 120 mm

(7

1

/4 in × 4

3

/8 in × 4

3

/4 in) (w/h/d)

Mass: Approx. 1.0 kg (2 lb 4 oz)

Package contents:

Main unit (1)

Parts for installation and connections (1 set)

Ask the dealer for detailed information.

Design and specifications are subject to change

without notice.

The Bluetooth® word mark and logos are registered

trademarks owned by the Bluetooth SIG, Inc. and

any use of such marks by Sony Corporation is under

license. Other trademarks and trade names are

those of their respective owners.

Windows Media is either a registered trademark or

trademark of Microsoft Corporation in the United

States and/or other countries.

This product is protected by certain intellectual

property rights of Microsoft Corporation. Use or

distribution of such technology outside of this

product is prohibited without a license from

Microsoft or an authorized Microsoft subsidiary.

Apple and iPhone are trademarks of Apple Inc.,

registered in the U.S. and other countries.

Apple CarPlay is a trademark of Apple Inc.

Android Auto is a trademark of Google LLC.

WebLink is a registered trademark of Abalta

Technologies, Inc. in the U.S. and a trademark in the

other countries.

All other trademarks are trademarks of their

respective owners.

Copyrights

10GB

Cautions

•Do not install this unit in a car that has no ACC

position. The display of the unit does not turn off

even after turning the ignition off, and this causes

battery drain.

• Run all ground (earth) leads to a common

ground (earth) point.

•Do not get the leads trapped under a screw or

caught in moving parts (e.g., seat railing).

•Before making connections, turn the car ignition

off to avoid short circuits.

• Connect the power supply leads  to the unit and

speakers before connecting it to the auxiliary

power connector.

•Be sure to insulate any loose unconnected leads

with electrical tape for safety.

•Choose the installation location carefully so that

the unit will not interfere with normal driving

operations.

•Avoid installing the unit in areas subject to dust,

dirt, excessive vibration, or high temperature, such

as in direct sunlight or near heater ducts.

•Use only the supplied mounting hardware for a

safe and secure installation.

Note on the power supply lead (yellow)

When connecting this unit in combination with other stereo

components, the amperage rating of the car circuit to which

the unit is connected must be higher than the sum of each

component’s fuse amperage rating.

Note on installing in cars with a start-stop system

The unit may restart when starting the engine from start-

stop. In this case, turn off the start-stop system of your car.

Note on installing in cars with electric parking brake

system

For cars with electric parking brakes, some related functions

(such as video blocking function) may not work properly.

Mounting angle adjustment

Adjust the mounting angle to less than 30°.

Parts List for Installation

•This parts list does not include all the package

contents.

•The mounting sleeve  is attached to the unit

before shipping. Before mounting the unit, use

the release keys  to remove the mounting

sleeve  from the unit. For details, see “Removing

the mounting sleeve” (page 14).

•Keep the release keys  for future use as they are

also necessary if you remove the unit from your

car.

Connection/Installation

 Power supply leads (1)  Mounting screws

(5 × max. 9 mm

(

7

/32 × max.

3

/8 in)) (4)

 Microphone (1)  Flat-mount base (1)

 Double-sided tape (1)  USB extension cables (2)

 Cable ties (2)  Mounting sleeve (1)

 Trim ring (1)  Release keys (2)

11GB

Connection

FUSE 10A

*

3

*

3

*

3

Subwoofer*

1

Power amplifier*

1

from a wired remote control (not

supplied)

*4

*

6

*

7

from a car antenna (aerial)*

5

Rear view

camera*

1



*

3

Light green

Purple/white striped

For details, see “Making

connections” (page 12).

See “Power connection diagram”

(page 13) for details.

*

2



*

8

USB device (for audio

playback only)*

1

from DAB antenna (aerial)

(not supplied)*

9

*

8



Smartphone, USB device

(for audio/video

playback)*

1

12GB

*1 Not supplied

*2 Speaker impedance: 4  to 8  × 4

*3 RCA pin cord (not supplied)

*4 Depending on the type of car, use an adaptor for a wired

remote control (not supplied).

For details on using the wired remote control, see “Using

the wired remote control” (page 13).

*5 Depending on the type of car, use an adaptor (not

supplied) if the antenna (aerial) connector does not fit.

*6 Whether in use or not, route the microphone input cord

so it does not interfere with driving operations. Secure

the cord with a clamp, etc., if it is installed around your

feet.

*7 For details on installing the microphone, see “Installing

the microphone” (page 13).

*8

*9 Set [Antenna Power] to [ON] (default) or [OFF] depending

on the type of DAB antenna (aerial) (not supplied).

Max. supply current 0.1 A

If you have a power antenna (aerial) without a relay

box, connecting this unit with the power supply

leads  may damage the antenna (aerial).

 To the car’s speaker connector

 To the car’s power connector

 To the parking brake switch lead

The mounting position of the parking brake

switch lead depends on your car.

Be sure to connect the parking brake lead (light

green) of the power supply leads  to the

parking brake switch lead.

 To the +12 V power terminal of the car’s rear

lamp lead (only when connecting the rear

view camera)

Memory hold connection

When the yellow power supply lead is connected,

power will always be supplied to the memory

circuit even when the ignition switch is turned off.

Speaker connection

•Before connecting the speakers, turn the unit off.

• Use speakers with an impedance of 4  to 8  and

with adequate power handling capacities to avoid

damage.

Making connections

1

Rear speaker

(right)

 Purple

2



Purple/black

striped

3

Front speaker

(right)

 Gray

4

 Gray/black striped

5

Front speaker

(left)

 White

6 

White/black

striped

7

Rear speaker

(left)

 Green

8 

Green/black

striped



12

continuous power

supply

Yellow

13

power antenna (aerial) /

power amplifier control

(REM OUT)

Blue/white striped

14

switched illumination

power supply

Orange/white

striped

15 switched power supply Red

16 ground (earth) Black

Parking brake switch lead

Hand brake type Foot brake type

13GB

Check your car’s auxiliary power connector and

match the connections of leads correctly

depending on the car.

Common connection

When the positions of the red and yellow

leads are inverted

For cars without ACC position

After matching the connections and switching

power supply leads correctly, connect the unit to

the car’s power supply. If you have any questions

and problems connecting your unit that are not

covered in this manual, consult the car dealer.

To capture your voice during handsfree calling, you

need to install the microphone .

Cautions

• It is extremely dangerous if the cord becomes

wound around the steering column or gearstick.

Be sure to keep it and other parts from interfering

with your driving operations.

• If airbags or any other shock-absorbing

equipment are in your car, contact the store where

you purchased this unit or the car dealer before

installation.

Notes

• When mounting on the dashboard, remove the visor clip

carefully from the microphone , then attach the flat-

mount base  to the microphone .

• Before attaching the double-sided tape , clean the

surface of the dashboard with a dry cloth.

1 To enable the wired remote control, set

[Steering Control] in [General] to [Preset].

Installation of the rear view camera (not supplied) is

required before use.

The picture from a rear view camera connected to

the CAMERA IN terminal is displayed when:

– the back lamp of your car lights up (or the shift

lever is set to the R (reverse) position).

– you press HOME, then touch [Rear Camera].

Power connection diagram

12

continuous power

supply

Yellow

15 switched power supply Red

12 switched power supply Yellow

15

continuous power

supply

Red

Auxiliary power connector

Red Red

Yellow Yellow

Red Red

Yellow Yellow

Red

Ye l l ow

Yellow

Installing the microphone

Using the wired remote control

Using the rear view camera





Clip (not supplied)





14GB

Installation

Before installing the unit, remove the mounting

sleeve  from the unit.

1 Insert both release keys  until they click,

and pull down the mounting sleeve , then

pull up the unit to separate.

•Before installing, make sure the catches on both

sides of the mounting sleeve  are bent inwards

3.5 mm (

5

/32 in).

•For Japanese cars, see “Mounting the unit in a

Japanese car” (page 14).

1 Position the mounting sleeve  inside the

dashboard, then bend the claws outward

for a tight fit.

2 Mount the unit onto the mounting sleeve

.

Notes

• If the catches are straight or bent outwards, the unit will

not be installed securely and may spring out.

• Make sure the 4 catches on the trim ring  are properly

engaged in the slots of the mounting sleeve .

Mounting the unit in a Japanese car

You may not be able to install this unit in some

Japanese cars. In such a case, consult your Sony

dealer.

When mounting this unit to the preinstalled

brackets of your car, use the mounting screws  in

the appropriate screw holes based on your car:

T for TOYOTA and N for NISSAN.

Note

To prevent a malfunction, install only with the mounting

screws .

Removing the mounting sleeve

Mounting the unit in the dashboard



Face the hook inwards.



Catch



Larger than

182 mm (7

1

/4 in)

Larger than

111 mm (4

3

/8 in)







To the dashboard/center console

Parts supplied with

your car



Bracket

15GB

When replacing the fuse, be sure to

use one matching the amperage

rating stated on the original fuse.

If the fuse blows, check the power

connection and replace the fuse.

If the fuse blows again after

replacement, there may be an

internal malfunction. In such a case, consult your

nearest Sony dealer.

Fuse replacement

Fuse (10 A)

2FR

Avertissement

Fabriqué en Thaïlande

La plaque signalétique reprenant la tension

d’alimentation, etc. se trouve sur le dessous du

châssis.

La validité du libellé CE se limite uniquement aux

pays où la loi l’impose, principalement les pays de

l’EEE (Espace économique européen) et la Suisse.

AVERTISSEMENT

Pour éviter les risques d’incendie et de choc,

n’exposez pas l’appareil à la pluie ou à

l’humidité.

Pour éviter les chocs électriques, n’ouvrez pas

le boîtier. Confiez les réparations à du

personnel qualifié uniquement.

Le soussigné, Sony Corporation, déclare que cet

équipement est conforme à la Directive 2014/53/

UE.

Le texte complet de la déclaration UE de conformité

est disponible à l’adresse internet suivante :

http://www.compliance.sony.de/

Avis à l’attention des clients : les informations

suivantes s’appliquent uniquement aux

appareils vendus dans des pays qui

appliquent les directives de l’Union

Européenne

Ce produit a été fabriqué par ou pour le compte de

Sony Corporation.

Importateur dans l’UE : Sony Europe B.V.

Les questions basées sur la législation européenne

pour l’importateur ou relatives à la conformité des

produits doivent être adressées au mandataire :

Sony Belgium, bijkantoor van Sony Europe B.V., Da

Vincilaan 7-D1, 1930 Zaventem, Belgique.

Elimination des piles et

accumulateurs et des équipements

électriques et électroniques

usagés (applicable dans les pays

de l’Union Européenne et dans les

autres pays disposant de systèmes de

collecte sélective)

Ce symbole apposé sur le produit, la pile ou

l’accumulateur, ou sur l’emballage, indique que le

produit et les piles et accumulateurs fournis avec ce

produit ne doivent pas être traités comme de

simples déchets ménagers. Sur certains types de

piles, ce symbole apparaît parfois combiné avec un

symbole chimique. Le symbole pour le plomb (Pb)

est rajouté lorsque ces piles contiennent plus de

0,004 % de plomb. En vous assurant que les

produits, piles et accumulateurs sont mis au rebut

de façon appropriée, vous participez activement à

la prévention des conséquences négatives que leur

mauvais traitement pourrait provoquer sur

l’environnement et sur la santé humaine. Le

recyclage des matériaux contribue par ailleurs à la

préservation des ressources naturelles. Pour les

produits qui, pour des raisons de sécurité, de

performance ou d’intégrité des données,

nécessitent une connexion permanente à une pile

ou à un accumulateur intégré(e), il conviendra de

vous rapprocher d’un Service Technique qualifié

pour effectuer son remplacement. En rapportant

votre appareil électrique, les piles et accumulateurs

en fin de vie à un point de collecte approprié vous

vous assurez que le produit, la pile ou

l’accumulateur intégré sera traité correctement.

Pour tous les autres cas de figure et afin d’enlever

les piles ou accumulateurs en toute sécurité de

votre appareil, reportez-vous au manuel

d’utilisation. Rapportez les piles et accumulateurs,

et les équipements électriques et électroniques

usagés au point de collecte approprié pour le

recyclage. Pour toute information complémentaire

au sujet du recyclage de ce produit ou des piles et

accumulateurs, vous pouvez contacter votre

municipalité, votre déchetterie locale ou le point de

vente où vous avez acheté ce produit.

Avis d’exclusion de responsabilité relatif aux

services proposés par des tiers

Les services proposés par des tiers peuvent être

modifiés, suspendus ou clôturés sans avis

préalable. Sony n’assume aucune responsabilité

dans ce genre de situation.

Pour votre sécurité, veuillez installer cet appareil

dans le tableau de bord de la voiture en tenant

compte du fait que l’arrière de l’appareil chauffe

en cours d’utilisation.

Pour de plus amples détails, reportez-vous à la

section « Raccordement/Installation » (page 10).

Avertissement si l’allumage de votre

véhicule ne possède pas de position ACC

N’installez pas cet appareil dans un véhicule qui

ne possède pas de position ACC. L’affichage de

l’appareil ne s’éteint pas même si le contact est

coupé, ce qui décharge la batterie.

3FR

Attention

SONY NE PEUT ÊTRE, EN AUCUN CAS, TENU POUR

RESPONSABLE D’UN QUELCONQUE DOMMAGE

ACCIDENTEL, INDIRECT OU ACCESSOIRE, OU DE

TOUT AUTRE DOMMAGE, Y COMPRIS, MAIS SANS

S’Y LIMITER, LA PERTE DE BÉNÉFICES, DE REVENUS,

DE DONNÉES, DE JOUISSANCE DU PRODUIT OU DE

TOUT ÉQUIPEMENT ASSOCIÉ, SON INDISPONIBILITÉ,

ET LE TEMPS PERDU PAR L’ACHETEUR, LIÉ À OU

RÉSULTANT DE L’UTILISATION DE CE PRODUIT, DE

SES COMPOSANTS MATÉRIELS ET/OU LOGICIELS.

Cher client, ce produit contient un émetteur radio.

Conformément au règlement UNECE n° 10, un

fabricant automobile peut imposer certaines

conditions particulières pour l’installation

d’émetteurs radio dans ses véhicules.

Veuillez vérifier le manuel d’utilisation de votre

véhicule ou contactez le constructeur de votre

véhicule ou votre concessionnaire, avant d’installer

ce produit dans votre véhicule.

Appels d’urgence

Le système BLUETOOTH mains libres embarqué et

le dispositif électronique qui y est connecté

fonctionnent grâce aux signaux radio, aux réseaux

cellulaires et aux lignes terrestres, tout comme la

fonction de programmation par l’utilisateur. La

connexion n’est donc pas garantie en toutes

circonstances.

Par conséquent, ne vous reposez pas uniquement

sur un dispositif électronique pour vos

communications importantes (tels que les appels

médicaux d’urgence).

Communication par BLUETOOTH

• Les micro-ondes émises par un dispositif

BLUETOOTH peuvent perturber le fonctionnement

des dispositifs médicaux électroniques. Dans les

circonstances qui suivent, mettez cet appareil,

ainsi que les autres dispositifs BLUETOOTH

présents, hors tension, car ils peuvent provoquer

un accident.

– En présence d’un gaz inflammable, dans un

hôpital, un train, un avion ou une station-service

– À proximité de portes automatiques ou d’un

système de détection d’incendie

• Cet appareil prend en charge les fonctionnalités

conformes à la norme BLUETOOTH afin de fournir

une connexion sécurisée lorsque la technologie

sans fil BLUETOOTH est utilisée. Mais, en fonction

de l’environnement, la sécurité peut ne pas être

suffisante. Soyez donc prudent lorsque vous

communiquez en utilisant la technologie sans fil

BLUETOOTH.

• Nous n’assumons aucune responsabilité en cas de

fuite d’informations au cours d’une

communication BLUETOOTH.

Si vous avez des questions concernant cet appareil

ou si vous rencontrez des problèmes qui ne sont

pas abordés dans ce mode d’emploi, contactez

votre revendeur Sony le plus proche.

Remarque importante

4FR

Appareil principal

La touche VOL (volume) + possède un point tactile.

 Affichage/écran tactile

 HOME

Affiche l’écran HOME (page 5).

ATT (atténuer)

Maintenez enfoncé pendant 1 seconde pour

atténuer le son.

Pour annuler, maintenez enfoncé à nouveau ou

appuyez sur VOL +.

 VOL (volume) +/–

 Récepteur de la télécommande

/ (précédent/suivant)

Fonctionne différemment selon la source

sélectionnée :

– Radio/DAB+ : permet de sélectionner une

présélection.

– USB/Audio BT : permet d’accéder au fichier

précédent/suivant.

Appuyez et maintenez enfoncé pour :

– Radio : rechercher une station

automatiquement (SEEK+/SEEK–).

– DAB+ : sélectionner une station (lorsque [Seek

Par] est réglé sur [A-Z])/rechercher une station

(lorsque [Seek Par] est réglé sur [Station Gp]).

– USB/Audio BT : reculer rapidement/avancer

rapidement.

 OPTION

Affiche l’écran OPTION (page 5).

VOICE

Appuyez et maintenez enfoncé pour activer la

fonction de commande vocale pour Apple

CarPlay et Android Auto™.

Emplacement des commandes

5FR

Affichages à l’écran

Écran de lecture :

Écran HOME :

Écran OPTION :

 Indications d’état

 (option de source)

Ouvre le menu d’option de source. Les éléments

disponibles varient selon la source.

 Zone spécifique à l’application

Affiche des commandes de lecture/indications

ou bien l’état de l’appareil. Les éléments affichés

varient selon la source.

 Horloge

Affiche l’heure selon le réglage défini sous Date/

Heure.

 (retour à l’écran de lecture)

Bascule entre l’écran HOME et l’écran de lecture.

 Touches de sélection des sources et réglages

Permettent de changer de source ou d’effectuer

divers réglages.

Tapez et glissez pour sélectionner l’icône de

réglage et d’autres icônes.

Touchez l’icône de la source que vous souhaitez

sélectionner.

S’allume quand le son est atténué.

S’allume quand AF (fréquences

alternatives) est disponible.

S’allume quand les informations de trafic

actuel (TA : annonces routières) sont

disponibles.

S’allume quand une annonce DAB est

disponible.

Indique l’état d’intensité du signal de la

radio DAB.

S’allume quand le signal Bluetooth® est

activé. Clignote quand la connexion est

en cours d’établissement.

S’allume lorsque le périphérique audio

est lisible en activant le profil A2DP

(Advanced Audio Distribution Profile,

profil de distribution audio avancée).

S’allume lorsqu’il est possible d’appeler

en mains libres en activant le profil HFP

(Handsfree Profile, profil mains libres).

Indique l’état d’intensité du signal du

téléphone mobile connecté.

Indique l’état de charge restant de la

batterie du téléphone mobile connecté.

Android

Auto

Apple

CarPlay

Radio

DAB+ Audio BT Téléphone

USB port 1 WebLink USB port 2

Cam. recul Réglages

6FR

 Touches de sélection du son

Modifie le son.

 (veille)

Bascule l’appareil en mode veille (la charge USB

reste disponible). Pour reprendre, appuyez sur

n’importe quelle touche.

 (Monitor off)

Éteint le moniteur. Lorsque le moniteur est

éteint, touchez une partie quelconque de

l’affichage pour le rallumer.

 (EXTRA BASS)

Permet de modifier le réglage EXTRA BASS.

 (EQ10/Caiss. bas.)

Permet de modifier le réglage EQ10/Caiss. bass.

Pairage avec un périphérique

BLUETOOTH

Lorsque vous connectez l’appareil à un

périphérique BLUETOOTH pour la première fois, il

est nécessaire qu’ils se reconnaissent

mutuellement (c’est ce que l’on appelle le

« pairage »). Le pairage permet à l’appareil et à

d’autres périphériques de se reconnaître

mutuellement.

1 Appuyez sur HOME, puis touchez [Réglages]

 [Bluetooth]  [Connexion Bluetooth] 

[ACTIVÉ]  [Pairage].

clignote lorsque l’appareil est en mode de

veille de pairage.

2 Procédez au pairage sur le périphérique

BLUETOOTH afin qu’il détecte cet appareil.

3 Sélectionnez le nom de votre modèle sur

l’affichage du périphérique BLUETOOTH*.

Une fois le pairage effectué, reste allumé.

* Si la saisie d’une clé d’authentification est requise sur

le périphérique BLUETOOTH, saisissez [0000].

Raccordement d’une caméra de

recul

En raccordant la caméra de recul en option à la

borne CAMERA IN, vous pouvez afficher l’image de

la caméra de recul. Pour plus d’informations,

reportez-vous à la section « Raccordement/

Installation » (page 10).

Pour afficher l’image de la caméra de recul

Appuyez sur HOME, puis touchez [Cam. recul].

Désactivation du mode de

démonstration

1 Appuyez sur HOME, puis touchez

[Réglages].

2 Touchez [Général], puis [Démo] pour le

régler sur [DÉSACTIVÉ].

3 Pour quitter le menu de configuration,

touchez deux fois (retour).

Opérations de base

La page est en cours de chargement...

Sony XAV-AX5550D Le manuel du propriétaire

Sony XAV-AX5550D Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents