Moog Videolarm Liberty PB26LG Installation And Operation Instructions Manual

Marque: Moog Videolarm

Modèle: Liberty PB26LG

Taper: Installation And Operation Instructions Manual

Ce manuel convient également à

Liberty SERIES

www.moogvideolarm.com

L I B E RT Y ™ S e r i e s

City-Wide Surveillance

Installation and Operation Instructions for the following models:

PB26LG Liberty Series wireless power box that includes a cellular router and

power supply. 110/220VAC input. Designed to work with Moog

Videolarm’s IP Ready Series of IP camera housings.

Before attempting to connect or operate this product, please read these instructions completely.

81-IN5459

10-23-2012

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. The installation should be made by a qualified installer.

b. The installation should be in compliance with local codes.

c. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the

unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including amplifiers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specified by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the

integrity of the installation is intact. Failure to comply with the foregoing could result in the

unit separating from the support structure and falling, with resultant damages or injury to

anyone or anything struck by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make

future shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us

at the following number:

The lightning flash with an arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the presence

of non-insulated “dangerous voltage”

within the product’s enclosure that may be

of sufficient magnitude to constitute a risk

to persons.

Este símbolo se piensa para alertar al usuario a la

presencia del “voltaje peligroso no-aisIado” dentro del

recinto de los productos que puede ser un riesgo de

choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la

presence “de la tension dangereuse” non-isolée dans la

clôture de produits qui peut être un risque de choc

électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença

“di tensão perigosa non-isolada” dentro do cerco dos

produtos que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla

presenza “di tensione pericolosa” non-isolata all’interno

della recinzione dei prodotti che può essere un rischio di

scossa elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones

importantes en la literatura que acompaña la

aplicación.

Ce symbole de point d’exclamation est prévu pour

alerter l’utilisateur à la presence des instructions

importantes dans la littérature accompagnant

l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der

Literatur alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido

alertar o usuário à presença de instruções importantes

na literatura que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti

nella letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING TO

QUALIFIED SERVICE PERSONNEL.

Limited Warranty for Moog Videolarm Products

Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:

PRODUCT CATEGORY PARTS \ LABOR

All Enclosures and Electronics* Five (5) Years

Poles/PolEvators™/CamEvator Three (3) Years

Warrior Series™/Q-View™/IR Illuminators Five (5) Years

SView Series™ Five (5) Years **6 months if used in auto scan/tour operation

Controllers Five (5) Years

Power Supplies Five (5) Years

EcoKit Three (3) Years

Accessory Brackets Five (5) Years

Liberty Dome Three (3) Years

*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™ Three (3) Years **6 months if used in auto scan/tour operation

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm

Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with

a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support

Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to

provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or

parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions.

TERMS AND CONDITIONS

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an

explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.

If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of

investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period

of the entire Product. The speci c warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that

part or the remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any

Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the

warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,

earthquakes), modi cation, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance

procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the

Product. Furthermore, Moog Videolarm shall have no liability where a schedule is speci ed for regular replacement or maintenance or cleaning of certain parts

(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-quali ed personnel; operation of the Product outside of the

published environmental and electrical parameters, or if such Product’s original identi cation (trademark, serial number) markings have been defaced, altered,

or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not

been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”

(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any

cost associated with removal of defective product and installation of replacement product is not included in this warranty.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR

ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL

CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT

THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS

PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND

WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL

PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER

FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,

REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

PB26LG

Energía De Entrada: 110 Consumo De Energía de VAC/220VAC 1A/.5A:

1Amp (120 vatios) en 120 VAC de salida de energía: VA 96 en 24 VAC

52 vatios de Heater/Blower 32 vatios de energía de la cámara

fotográca

Todo el interruptor principal del poste con un contacto de por lo

menos 3m m en cada poste será incorporado en la instalación

eléctrica del edicio.

Herramientas Requeridas: destornillador de cabeza llana del 150"7/16

llave de la llave o del zócalo 9/16 o zócalo

Puissance D'entrée : 110 Puissance D'Énergie de VAC/220VAC 1A/.5A :

1Amp (120 watts) à 120 VCA de rendement de puissance: VA 96 à 24

VCA 52 watts de Heater/Blower 32 watts de puissance d'appareil-

photo

Un tout le commutateur principal de poteau avec un contact au moins

de 3mm dans chaque poteau sera incorporé dans l'installation

électrique du bâtiment.

Outils Requis: tournevis à tête plate de 150"7/16 clé de clé ou de douille

9/16 ou douille

Zugeführte Energie: 110 VAC/220VAC 1A/.5A

Leistungsaufnahme: 1Amp (120 Watt) bei 120 VAC

Abgabeleistung: VA 96 bei 24 VAC 52 Watt

Heater/Blower 32 Watt Kamera-Energie

Ein aller Pfostenhauptschalter mit einem Kontakt von 3mm mindestens

in jedem Pfosten wird in der elektrischen Installation des Gebäudes

enthalten.

Werkzeuge Erforderten: 150"Flachkopfschraubenzieher 7/16 Schlüssel-

oder Einfaßung 9/16 Schlüssel oder Einfaßung

Poder De Entrada: 110 Consumo De Potência de VAC/220VAC 1A/.5A:

1Amp (120 watts) em 120 VAC de saída de poder: VA 96 em 24 VAC

52 watts de Heater/Blower 32 watts de poder da câmera

Todo o interruptor principal do pólo com um contato ao menos de

3mm em cada pólo será incorporado na instalação elétrica do edifício.

As Ferramentas Requereram: chave de fenda athead do 150"7/16 de

chave da chave ou do soquete 9/16 ou soquete

Alimentazione in ingresso Di Entrata: 110 Assorbimento di corrente Di

energia di VAC/220VAC 1A/.5A: 1Amp (120 watt) a 120 VCA di uscita

di alimentazione: VA 96 a 24 VCA 52 watt di Heater/Blower 32 watt di

alimentazione della macchina fotograca

Tutto l'interruttore principale del palo con un contatto almeno di 3mm

in ogni palo sarà compreso nell'installazione elettrica della costruzione.

Attrezzi Richiesti: cacciavite a testa piatta del 150"7/16 di chiave dallo

zoccolo o dalla chiave 9/16 o zoccolo

Input Power: 110 VAC/220VAC 1A/.5A

Power Consumption: 1Amp (120 Watts) at 120 VAC

Power Output: 96 VA at 24 VAC 52 Watts

Heater/Blower 32 Watts Camera Power

An all pole main switch with a contact of at least 3mm in each

pole shall be incorporated in the electrical installation of the

building.

Tools Required: .150” Flathead Screwdriver 7/16 Wrench or Socket

9/16 Wrench or Socke

Electrical Specications

Français

Deutsch

Italiano

Portuguese

Español

English

Contents of Box

Power Feed Locations:

Pendant

mount location

Liquid tight strain

relief for main

power

Liquid tight

plug for optional

power / antenna

Liquid tight

modem cover

3G - 4G units

Liquid tight

security latch

WALL MOUNTING

POLE MOUNTING

Attach unit securely with (4) ⅜” bolts.

• Ate la unidad con seguridad con (4) pernos del ⅜ los”.

• Attachez l'unité solidement avec (4) boulons

de ⅜ des ».

• Bringen Sie Maßeinheit sicher mit (4) ⅜“

Schraubbolzen an.

• Una a unidade firmemente com (4) parafusos do ⅜”.

• Attacchi saldamente l'unità con (4) bulloni del ⅜„.

Step One: Attach the pole clips to the mounting

tabs as shown. Use hardware provided.

• Paso uno: Ate los clips del poste a las lengüetas del montaje

como se muestra. Utilice el hardware proporcionado.

• Étape une : Attachez les agrafes de poteau aux étiquettes de

support comme montrées. Utilisez le matériel fourni.

• Schritt einer: Bringen Sie die Pfostenclips zu den

Montagevorsprüngen wie gezeigt an. Benutzen Sie die

bereitgestellte Hardware.

• Etapa uma: Una os grampos do pólo às abas da montagem

como mostradas. Use a ferragem fornecida.

• Punto uno: Attacchi le clip del palo alle linguette del

montaggio come indicate. Utilizzi i fissaggi forniti.

Step Two: PB26LG is ready to mount. Use slots

to attach steel straps.

• Paso dos: PB26LG está listo para montar. Utilice las

ranuras para atar las correas de acero.

• Étape deux : PB26LG est prêt à monter. Employez les

fentes pour attacher les courroies en acier.

• Schritt zwei: PB26LG ist bereit anzubringen. Benutzen Sie

Schlitze, um Stahlbügel anzubringen.

• Etapa dois: PB26LG está pronto para montar. Use

entalhes para unir as cintas de aço.

• Punto due: PB26LG è pronto a montare. Usi le

scanalature per attaccare le cinghie d'acciaio.

Step Three: Use steel straps to mount the

unit to a pole.

• Paso tres: Utilice las correas de acero para montar la

unidad a un poste.

• Étape trois : Employez les courroies en acier pour

monter l'unité à un poteau.

• Schritt drei: Benutzen Sie Stahlbügel, um die Maßeinheit

zu einem Pfosten anzubringen.

• Etapa três: Use as cintas de aço para montar a

unidade a um pólo.

• Punto tre: Usi le cinghie d'acciaio per montare l'unità

ad un palo.

Inside view of the unit.

• Dentro de la vista de la unidad.

• Dessus à l'intérieur de la vue de l'unité.

• Innerhalb der Ansicht der Maßeinheit.

• Dentro da ideia da unidade.

• All'interno della vista dell'unità.

The wall mount bracket must be attached

using the gasket as shown.

• El soporte del montaje de la pared se debe atar usando la

junta como se muestra.

• La parenthèse de bâti de mur doit être attachée utilisant la

garniture comme montrée.

• Der Wandeinfassungshaltewinkel muss unter Verwendung

der Dichtung wie gezeigt angebracht werden.

• O suporte da montagem da parede deve ser unido usando

a gaxeta como mostrado.

• La staffa del supporto della parete deve essere attaccata

per mezzo della guarnizione come indicata.

Wall Mount

Gasket

This is the assembled unit with the housing

and conduit.

• Ésta es la unidad montada con la cubierta

y el conducto.

• C'est l'unité assemblée avec le logement

et le conduit.

• Dieses ist die zusammengebaute Maßeinheit mit dem

Gehäuse und dem Rohr.

• Esta é a unidade montada com a carcaça

e a canalização.

• Ciò è l'unità montata con l'alloggiamento

ed il condotto.

Conduit Fittings

PENDANT MOUNTING

Remove

barrier

cover

Remove barrier cover.

• Quite la cubierta de la barrera.

• Enlevez la couverture de barrière.

• Entfernen Sie Sperrenabdeckung.

• Remova a tampa da barreira.

• Rimuova la copertura della barriera.

o della vista dell'unità.

ON/OFF switch

(will not turn off

wireless circuit)

115/240VAC

selector switch

120/240VAC

input

12VDC output

24VAC

Aux. output

120/240VAC

Aux. output

1. Move the 115//240VAC selector switch (3) to the

desired position

2. Insure that the ON/OFF switch (2) is in the off position

3. Attach the in coming “main” power to the 120/240 VAC input

4. Move the ON/OFF switch (2) to the ON position.

• 1. Mueva el interruptor de selector 115//240VAC (3) a

la posición deseada

2. Asegure que el interruptor CON./DESC. (2) está en la

posición de reposo

3. Ate en energía “principal” que viene a la entrada de 120/240

VAC 4. Mueva el interruptor CON./DESC. (2) a la posición de trabajo.

• 1. Déplacez le sélecteur 115//240VAC (3) à la position désirée

2. Assurez-vous que le commutateur "MARCHE/ARRÊT" (2) est dans la

position de repos

3. Attachez dans la prochaine puissance « principale » à l'entrée de

120/240 VCA

4. Déplacez le commutateur "MARCHE/ARRÊT" (2) à la

position de fonctionnement.

• 1. Verschieben Sie den Schalter des Wähl 115//240VAC (3) auf die

gewünschte Position

2. Versichern Sie, dass der Ein/Aus-Schalter (2) in der Ausschaltstellung ist

3. Bringen Sie in kommender „Haupt“ Energie zum 120/240 VAC-

Eingang an

4. Verschieben Sie den Ein/Aus-Schalter (2) auf die Arbeitsstellung.

• 1. Mova o interruptor de seletor 115//240VAC (3) para a

posição desejada

2. Segure que o interruptor DE LIGAR/DESLIGAR (2) está no

posição de repouso

3. Una no poder “principal” de vinda à entrada de 120/240 de VAC

4. Mova o interruptor DE LIGAR/DESLIGAR (2) para o

posição de functionamento.

• 1. Sposti l'interruttore di selettore 115//240VAC (3) alla posizione voluta

2. Assicuri che l'interruttore acceso/spento (2) è nella posizione di riposo

3. Attacchi nel potere “principale„ venente all'input da 120/240 di VCA

4. Sposti l'interruttore acceso/spento (2) alla posizione di funzionamento.

Assign your camera the static TCP/IP address of

192.168.1.50 with a subnet mask of 255.255.255.0 and a

gateway of 192.168.1.1.

• Asigne a su cámara la dirección estática del TCP/IP de 192.168.1.50 con

un subnet mask de 255.255.255.0 y una entrada de 192.168.1.1.

• Assignez à votre appareil-photo l'adresse statique de TCP/IP de

192.168.1.50 avec un subnet mask de 255.255.255.0 et un passage de

192.168.1.1.

• Weisen Sie Ihrer Kamera die statische IP-Adresse von 192.168.1.50 mit

einem subnet mask von 255.255.255.0 und einem Zugang von

192.168.1.1 zu.

• Atribua a sua câmera o endereço de estática do TCP/IP de 192.168.1.50

com um subnet mask de 255.255.255.0 e uma passagem de 192.168.1.1.

• Assegni alla vostra macchina fotografica l'indirizzo statico del TCP/IP di

192.168.1.50 con un subnet mask di 255.255.255.0 e un ingresso di

192.168.1.1.

3G/4G Camera Prep

Connect to your camera with a laptop or pc

• Conecte con su cámara con un ordenador portátil o

una PC.

• Reliez à votre appareil-photo à un ordinateur portable

ou à un PC.

• Schließen Sie an Ihre Kamera an einen Laptop oder an

einen PC an.

• Conecte a sua câmera com um portátil ou um PC.

• Colleghi alla vostra macchina fotografica con un

computer portatile o un pc.

Change to HTTP port from the default port 80 to

the port 12345.

• Cambie al puerto del HTTP del puerto 80 del defecto al puerto 12345.

• Changez en le port de HTTP du port 80 de défaut en port 12345.

• Ändern Sie zum HTTP-Hafen vom Rückstellungshafen 80 zum Hafen

12345.

• Mude ao porto do HTTP do porto 80 do defeito ao porto 12345.

• Cambi all'orificio del HTTP dall'orificio 80 di difetto all'orificio 12345.

USB 3G/4G Card Prep

When ordering your service with your provider, have

them add a static ip address to the service <extra

charge may be involved>

• Al pedir su servicio con su abastecedor, haga que agreguen un IP

address estático al servicio (el recargo puede estar implicado).

• En commandant votre service avec votre fournisseur, faites-ajouter les

un IP address statique au service (le supplément peut être impliqué).

• Wenn Sie Ihren Service mit Ihrem Versorger bestellen, lassen Sie sie ein

statisches IP address dem Service hinzufügen (Extragebühr kann

beteiligt sein) .

• Ao requisitar seu serviço com seu fornecedor, mande-os adicionar um

IP address de estática ao serviço (a sobretaxa pode ser involvida.

• Nell'ordinare il vostro servizio con il vostro fornitore, facciali aggiungere

un IP address statico al servizio (la carica supplementare può essere

implicata).

Some users may require WiFi access to the unit as well. Connect to the WiFi

network by selecting the SSID that contains the word Videolarm and a

combination of three letters and numbers. An example is Videolarm2A0 as

shown above. The encryption key for the network is password.

• Algunos usuarios pueden requerir el acceso de WiFi a la unidad también. Conecte con la red de

WiFi seleccionando el SSID que contiene la palabra Videolarm y una combinación de tres letras y

números. Un ejemplo es Videolarm2A0 como se muestra arriba. La llave de encripción para la red

es contraseña.

• Quelques utilisateurs peuvent avoir besoin de l'accès de WiFi à l'unité aussi bien. Reliez au réseau de

WiFi en choisissant le SSID qui contient le mot Videolarm et une combinaison de trois lettres et

nombres. Un exemple est Videolarm2A0 comme montré ci-dessus. La clef de chiffrage pour le

réseau est mot de passe.

• Einige Benutzer können WiFi Zugang zur Maßeinheit außerdem fordern. Schließen Sie an das WiFi

Netz an, indem Sie das SSID vorwählen, das das Wort Videolarm und eine Kombination von drei

Buchstaben und von Zahlen enthält. Ein Beispiel ist Videolarm2A0 wie gezeigt oben. Der

Verschlüsselungschlüssel für das Netz ist Kennwort.

• Alguns usuários podem exigir o acesso de WiFi à unidade também. Conecte à rede de WiFi

selecionando o SSID que contem a palavra Videolarm e uma combinação de três letras e

números. Um exemplo é Videolarm2A0 como mostrado acima. A chave de cifragem para a rede

é senha.

• Alcuni utenti possono richiedere l'accesso di WiFi all'unità pure. Colleghi alla rete di WiFi

selezionando lo SSID che contiene la parola Videolarm e una combinazione di tre lettere e numeri.

Un esempio è Videolarm2A0 come indicato sopra. La chiave di crittografia per la rete è parola

d'accesso.

Connecting to the WiFI network allows a connection to the admin interface

on the address http://192.168.1.1 as well as local access to the camera on

address http://192.168.1.50:12345. The username for the admin interace is

root with a password of admin.

• La conexión con la red de WiFI permite una conexión al interfaz del admin en la

dirección http://192.168.1.1 así como el acceso local a la cámara en la dirección

http://192.168.1.50:12345.

El username para el interace del admin es raíz con una contraseña del admin.

• Se relier au réseau de WiFI permet un raccordement à l'interface d'admin sur

l'adresse http://192.168.1.1 aussi bien que l'accès local à l'appareil-photo sur

l'adresse http://192.168.1.50:12345. L'username pour l'interace d'admin est racine

avec un mot de passe d'admin.

• Die Verbindung an das WiFI Netz erlaubt einen Anschluss zur admin-Schnittstelle auf

der Adresse http://192.168.1.1 sowie lokalen Zugang zur Kamera auf Adresse

http://192.168.1.50:12345. Das username für das admin interace ist Wurzel mit

einem Kennwort von admin.

• Conectar à rede de WiFI permite uma conexão à relação do admin no endereço

http://192.168.1.1 assim como o acesso local à câmera no endereço

http://192.168.1.50:12345. O username para o interace do admin é raiz com uma

senha do admin.

• Collegandosi alla rete di WiFI permette un collegamento all'interfaccia di admin

sull'indirizzo http://192.168.1.1 così come accesso locale alla macchina fotografica

sull'indirizzo http://192.168.1.50:12345. Il username per il interace di admin è radice

con una parola d'accesso del admin.

Advanced configuration options for changing the WiFI settings, etc. are

available through the admin interface.

• Las opciones de configuración avanzadas para cambiar los ajustes de WiFI, el etc.

están disponibles a través del interfaz del admin.

• Les options de configuration avancées pour changer les arrangements de WiFI,

etc. sont disponibles par l'interface d'admin.

• Vorgerückte Konfigurationswahlen für das Ändern der WiFI Einstellungen, des etc.

sind durch die admin-Schnittstelle vorhanden.

• As opções de configuração avançadas para mudar os ajustes de WiFI, etc. estão

disponíveis através da relação do admin.

• Le opzioni di configurazione avanzate per il cambiamento le regolazioni di WiFI,

ecc. sono disponibili attraverso l'interfaccia di admin.

Use the provided velcro to mount and secure the USB modem.

• Utilice el Velcro proporcionado para montar y para asegurar el módem del USB.

• Employez le Velcro fourni pour monter et fixer le modem d'USB.

• Benutzen Sie den zur Verfügung gestellten Flausch, um das USB-Modem anzubringen und zu sichern.

• Use o Velcro fornecido para montar e fixar o modem do USB.

• Usi il Velcro fornito per montare e fissare il modem del USB.

Assemble the modem cover as shown.

• Utilice el Velcro proporcionado para montar y para asegurar el módem del USB.

• Employez le Velcro fourni pour monter et fixer le modem d'USB.

• Benutzen Sie den zur Verfügung gestellten Flausch, um das USB-Modem anzubringen und zu sichern.

• Use o Velcro fornecido para montar e fixar o modem do USB.

• Usi il Velcro fornito per montare e fissare il modem del USB.

SCREW

SPLIT WASHER

FLAT WASHER

CLAMP RING

CARD COVER

GASKET

FLAT WASHER

HEX NUT

MODEM - INSTALL

LID - INSTALL (3G - 4G)

SUPPORT FOR 3G/4G CARDS:

The PB26LG can support cards up to 5.25” x 1.45” x .5” ( L x W x D ) in size. Some cards may have intermittent service operating

at temperatures above (122°F).

INPUT FOR CAMERA

24VAC POWER FOR

CAAMERA AND HOUSING

ALARM INPUT FOR IP RESET

120VAC INPUT

Attach 120VAC main power to connector.

• Ate la alimentación principal 120VAC

al conectador.

• Attachez l'alimentation secteur 120VAC

au connecteur.

• Bringen Sie Netzspannung 120VAC zum

Verbindungsstück an.

• Una o poder 120VAC principal ao conector.

• Attacchi la alimentazione di rete

120VAC al connettore.

Connect down and camera power to this connector green wire and yellow

wire are for housing heater and blower. Red/black and orange/black are

for camera power. Because it is 24VAC. It is not polarity sensative.

• Conecte abajo y la energía de la cámara a este alambre del verde del

conectador y al alambre amarillo está para el calentador y el soplador de la

cubierta. Rojo/negro y naranja/negro esté para la energía de la cámara. Porque

es 24VAC. No es polaridad sensative.

• Reliez vers le bas et la puissance d'appareil-photo à ce fil de vert de connecteur

et à fil jaune sont pour le réchauffeur et le ventilateur de logement. Rouge/noir et

orange/noir soyez pour la puissance d'appareil-photo. Puisque c'est 24VAC. Ce

n'est pas polarité sensative.

• Schließen Sie unten an und Kameraenergie zu diesem Verbindungsstückgrün-

draht und zum gelben Draht sind für Gehäuseheizung und -gebläse.

Rot/Schwarzes und Orange/Schwarzes seien Sie für Kameraenergie. Weil es

24VAC ist. Es ist nicht die sensative Polarität.

• Conecte para baixo e o poder da câmera a este fio do verde do conector e ao

fio amarelo é para o calefator e o ventilador da carcaça. Vermelho/preto e

laranja/preto seja para o poder da câmera. Porque é 24VAC.

Não é polaridade sensative.

• Colleghi giù ed il potere della macchina fotografica a questo legare di verde del

connettore ed a legare giallo è per il riscaldatore ed il ventilatore

dell'alloggiamento. Rosso/nero ed arancio/nero sia per potere della macchina

fotografica. Poiché è 24VAC. Non è polarità sensative.

Connect network camera to network cable.

• Conecte la cámara de red con el cable

de la red.

• Reliez l'appareil-photo de réseau au câble

de réseau.

• Schließen Sie Netzkamera an Netzkabel an.

• Conecte a câmera de rede ao cabo da

rede.

• Colleghi la macchina fotografica di rete al

cavo della rete.

WAN INPUT

LAN INPUT

Connect appropriate alarm output of the camera to

the IP Reset alarm input wires. Please consult your

cameras operating instruction to insure proper

installation. Color codes for the ip reset are located

on device cover

IP RESET ALARM WIRES

IP RESET DEVICE

Replacement Parts

Liberty Series

PB26LG

DESCRIPTION

1 RP30VL3744 PB26LG POWER BOX

RP30VL2742 POLE MOUNT CLIPS

3 RP30VL3740 ELECTRONICS MOUNTING PLATE

4 RP70TRANS12 TRANSFORMER, 96 VA

5 RP30VL3737 SURGE BRACKET

6 RP70LF3VR3 120/240V 50-60 Hz LINE FILTER

7 RPSPPA405 15A PARALLEL SURGE PROTECTOR

RP110IPR01 IP RESET

9 RP76VL2007 4G POWER AND CONNECTION BOARD ASSEMBLY

10 RP70VL3727 BOARD SHIELD, LIBERTY SERIES

11 RP76RCNEX1 MOBILE ROUTER

PART #

RP71BLEH220 BLOWER, 115VAC 60mm

RP30VL3736 BLOWER BRACKET

RP96GK3745 MODEM LID GASKET

RP30VL3742 MODEM LID

RP94FSSR04 CABLE STRAIN RELIEF

RPPBLOCK TAMPER PROOF, LOCK, PB26

RPPB26PLUG ½” PLUG, 94-FSUP09, 94-FSRT03, 96-REORG19

Product Registration/Warranty

Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest

quality products available and superior customer service.

Should a problem arise, rest assured that Moog Videolarm stands behind its products by offering impressive 3 Year and 5 Year warranties, depending on the product

purchased. See full warranty details at www.moogvideolarm.com/technical-support/warranty-plan/

Please take a few moments to register your purchase via the Online Product Registration Form at:

www.moogvideolarm.com/technical-support/product-registration

• Simple and Trouble-Free RMA process

• Receive product updates, and special promotion

• Eliminate the need to archive original purchase documents:

Receipts, Purchase Orders, etc…