GE AJCM08AWH Le manuel du propriétaire

Taper
Le manuel du propriétaire
Write the model and serial
numbers here:
Model # _________________
Serial # _________________
You can find the this information
on a label attached to the right
side of the chassis.
GE is a trademark of the General Electric Company. Manufactured under trademark license.
AIR CONDITIONER
26” Built-In Wi-Fi
49-5000492 Rev. 4 02-21 GEA
ESPAÑOL
For a Spanish version of this
manual, visit our Website at
GEAppliances.com.
Para consultar una version
en español de este manual
de instrucciones, visite nuestro
sitio de internet
GEAppliances.com.
FRANÇAIS
For a French version of this
manual, visit our Website at
GEAppliances.ca.
Pour un version français de
ce manuel d’utilisation, veuillez
visiter notre site web à l’adresse
GEAppliances.ca.
SAFETY INFORMATION .........3
USING THE AIR
CONDITIONER ..............4
WI-FI SETUP ......................7
CARE AND CLEANING ...........9
INSTALLATION
INSTRUCTIONS ..............10
TROUBLESHOOTING TIPS ......12
CONSUMER SUPPORT
Warranty ............................15
Consumer Support ....................16
OWNER’S MANUAL &
INSTALLATION
INSTRUCTIONS
Cool Only Models
AJCQ06LWH
AJCQ08AWH
AJCQ10AWH
AJCQ10DWH
AJCQ12AWH
AJCQ12DWH
AJCQ14DWH
Cool Only High Mount Models
AJCM08AWH
AJCM10AWH
AJCM10DWH
AJCM12DWH
Heat/Cool Models
AJEQ08AWH
AJEQ10DWH
AJEQ12DWH
AJEQ14DWH
Heat/Cool High Mount Models
AJEM12DWH
Heatpump Models
AJHQ08AWH
AJHQ12DWH
2 49-5000492 Rev. 4
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances
product, and we think you will too. Among other things, registration of your appliance ensures that we
can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the
Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration
card included in the packing material.
49-5000492 Rev. 4 3
SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
For your safety, the information in this manual must be followed to minimize the risk of
fire, electric shock or personal injury.
Ŷ8VHWKLVDSSOLDQFHRQO\IRULWVLQWHQGHGSXUSRVHDV
described in this Owner’s Manual.
ŶThis air conditioner must be properly installed in accordance
with the Installation Instructions before it is used.
ŶNever unplug your air conditioner by pulling on the
power cord. Always grip plug firmly and pull straight
out from the receptacle.
ŶReplace immediately all electric service cords that
have become frayed or otherwise damaged. A
damaged power supply cord must be replaced with a
new power supply cord obtained from the manufacturer
and not repaired. Do not use a cord that shows cracks
or abrasion damage along its length or at either the
plug or connector end.
ŶTurn the unit OFF and unplug your air conditioner
before cleaning.
ŶFor your safety…do not store or use combustible
materials, gasoline or other flammable vapors or
liquids in the vicinity of this or any other appliance.
ŶIf the receptacle does not match the plug, the receptacle
must be changed out by a qualified electrician.
USE OF EXTENSION CORDS
RISK OF FIRE. Could cause serious injury or death.
Ŷ'2127XVHDQH[WHQVLRQFRUGZLWKWKLVair
conditioner.
Ŷ'2127XVHVXUJHSURWHFWRUVRUPXOWLRXWOHW
adaptors with this air conditioner.
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third
(ground) prong from the power cord. For personal safety,
this appliance must be properly grounded.
DO NOT use an adapter plug with this appliance.
The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall outlet to minimize the possibility
of electric shock hazard from this appliance.
Power cord includes a current interrupter device. A test
and reset button is provided on the plug case. The device
should be tested on a periodic basis by first pressing the
TEST button and then the RESET button while plugged
into the outlet. If the TEST button does not trip or if the
RESET button will not stay engaged, discontinue use of the
air conditioner and contact a qualified service technician.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Where a 2-prong wall outlet is encountered, it is your
personal responsibility and obligation to have it replaced
with a properly grounded 3-prong wall outlet.
The air conditioner should always be plugged into its
own individual electrical outlet which has a voltage rating
that matches the rating plate.
This provides the best performance and also prevents
overloading house wiring circuits which could cause a
fire hazard from overheated wires.
See the Installation Instructions, Electrical
Requirements section for specific electrical connection
requirements.
WARNING
READ AND SAVE THESE INSTRUCTIONS
For appliance recycling information please visit GEAppliances.com/recycling.
WARNING
4 49-5000492 Rev. 4
Air Conditioner Controls
Appearance may vary.
ŶTo ensure proper operation, aim the remote control at
the signal receiver on the air conditioner.
ŶThe remote control signal has a range up to 21 feet.
ŶThe remote control will control the unit even if
connected to the Wi-Fi.
ŶMake sure nothing is between the air conditioner and
the remote control that could block the signal.
ŶMake sure the battery is fresh and installed correctly—
see the Care and Cleaning section.
Remote Control
Lights below the touch pads on the control panel indicate
the selected settings
Using the Air Conditioner - Controls
USING THE AIR CONDITIONER
1. POWER
Turns air conditioner on and off.
2. DISPLAY
Displays the temperature setting.
3. MODE
8VHWRVHWHEAT (on some models), COOL, FAN, ECO,
or DRY modes. Indicator lights on the controls will show
the mode selected.
4. TEMP INCREASE (+) / DECREASE (–) PADS
8VHWRVHWWHPSHUDWXUHZKHQLQ+($7RQVRPHPRGHOV
COOL, ECO, or DRY modes.
5. FAN SPEED
8VHWRVHWWKHIDQVSHHGDWAUTO, LOW, MEDIUM, or
HIGH. Indicator lights will show the speed selected.
6. FILTER
Monitors accumulated fan run time as a reminder to clean
the filter.
7. WI-FI
This unit is GE Appliances Wi-Fi Connect Enabled.
8. SLEEP
Allows room temperature to increase in Cool mode or
decrease in Heat mode during sleeping hours.
49-5000492 Rev. 4 5
Using the Air Conditioner - Features
USING THE AIR CONDITIONER
To Adjust Fan Speeds
Press the FAN SPEED button to select the FAN SPEED
in four steps - AUTO, LOW, MED, or HIGH. Each time
the button is pressed, the fan speed mode is shifted.
For some models, the fan speed can not be adjusted
under HEAT mode. In DRY mode, the fan speed is
controlled at low automatically.
In AUTO, the fan speed will automatically operate at the
speed needed to provide optimum comfort. If the room
needs faster cooling to meet the set temperature, the
fan will automatically increase. If the room needs less
cooling, the fan will automatically decrease.
SLEEP
SLEEP set the unit to gradually change setting over an 8
hour period to allow for increased energy savings during
sleeping hours. The SLEEP mode is available only in
COOL and FAN only settings.
Press the SLEEP mode pad and its light will illuminate.
The FAN indicator will stay at the same setting but the air
conditioner will automatically change the FAN speed to
low in either the COOL or FAN only mode.
In FAN only mode, the fan will stay in the LOW speed
setting for 8 hours. After 8 hours, the air conditioner will
resume the settings that were in place before the SLEEP
mode pad was pressed.
In COOL and HEAT modes, the fan will stay in LOW
speed setting for 8 hours from the time the SLEEP mode
pad was pressed. The air conditioner will raise the set
point 2ºF(1ºC) in cooling (lower the set point in heating)
in 30 minutes and 2ºF(1ºC) more in another 30 minutes
where it will remain for another 7 hours. After this 8-hour
period, the unit will resume the settings that were in place
before the SLEEP mode pad was pressed.
While the unit is in SLEEP mode, pressing any pad will
return it to the settings that were in place before the
SLEEP mode was pressed.
Check Filter
Press the FILTER button to initiate this feature. This
feature is a reminder to clean the air filter for more
efficient operation.
The LED (light) will illuminate after 250 hours of
operation. To reset after cleaning the filter, press the
FILTER button and the light will go off.
Control Panel Lights
This unit has a control panel lights ON/OFF feature that
turns them off when there is no activity for more than
1 minute. To wake up the lights, press any pad on the
controls and the lights will come on to show the previous
settings. To turn this feature off, press and hold the
SLEEP pad for 3 seconds. The unit will beep to signal a
successful toggle off of this feature.
Pressing the DISPLAY on the wireless remote will turn
the control panel lights off immediately.
To Select the Operating Mode
To choose operating mode, press the MODE button.
Each time you press the button, a mode is selected in
a sequence that goes from HEAT (on some models),
COOL, FAN, ECO, and DRY only. The indicator light will
be illuminated and remain on once the mode is selected.
Models AJHQ08AWH and AJHQ12DWH are Heatpumps
and the heating function will automatically switch
between electric heat mode and heatpump mode to
maintain room set temperature and to reduce operating
costs. At outdoor temperatures below 40ºF(4.4ºC),
the unit will operate in electric heat mode only. The
AJHQ08AWH is not intended to be the sole source of
heat.
To operate in FAN only Mode:
Ŷ8VHWKLVIXQFWLRQRQO\ZKHQFRROLQJRUKHDWLQJRQVRPH
models) is not desired. You can choose any fan speed
you prefer.
ŶDuring this function, the display will show the actual
room temperature, not the set temperature in the
cooling or heating (on some models) mode.
ŶIn FAN only mode, the temperature is not adjustable.
To operate in ECO Mode:
Ŷ
With this feature, the unit will operate in COOL mode
only. The fan will operate with the compressor to
cool the space. The fan will continue to run for 3
minutes after the compressor stops and the room
set temperature has been met. The fan then cycles
on for 2 minutes at 10 minute intervals until the room
temperature is above the set point, at which time the
compressor turns on and cooling starts.
To operate in DRY Mode:
Ŷ
In this mode, the air conditioner will generally operate in
the form of a dehumidifer. Since the conditioned space
is a closed or sealed area, some degree of cooling
will occur. In DRY mode, the fan operates in LOW fan
speed only.
Fahrenheit vs. Celsius
To change the temperature display from Fahrenheit to Celsius, press and + together and hold for 3 seconds.
6 49-5000492 Rev. 4
Using the Air Conditioner - Features
USING THE AIR CONDITIONER
Additional Features
The “Cool” circuit has an automatic 3 minute delayed
start if the unit is turned off and on quickly. This prevents
overheating of the compressor and possible circuit breaker
tripping. The fan will continue to run during this time.
There is a 2 second delay for the compressor to stop when
selecting fan or heat. This is to cover the possibility of
having to roll through to select another mode.
The control will maintain the set temperature within 1°F
between 62°F and 86°F in cool or heat mode (on some
models).
After a power outage, the unit will remember last setting
and return the unit to that setting when power is restore.
Air Direction
Adjustable louvers control air flow direction.
The louvers will allow you to direct the air flow up or down
and left or right throughout the room as needed until the
desired left/right direction is obtained. Pivot horizontal
louvers until the desired up/down direction is obtained.
Remote Wall Thermostat (Heat/Cool models only)
All heat/cool models are capable of being controlled by a
24 VAC remote wall thermostat. The thermostat control
connection board is located behind a metal cover on the
right side of the metal chassis cover. To open the cover,
remove the Phillips head screw and lift from the slots at the
bottom. To properly connect the wiring from a remote wall
thermostat, follow these steps:
1. Order the 8-pin connector from GE Appliances Service.
Call 1-800-626-2002 and order WP26X24981. A
connector is required for each unit being controlled by
a wall thermostat
2. Install the remote thermostat according to the
directions included with it.
8VLQJZLUHQXWVLQFOXGHGZLWKWKHSLQFRQQHFWRU
connect the wiring from the wall thermostat per the
following; (Proper connection of the wiring is critical.
Improper hookups could result in damage to the air
conditioner components and may not be covered by
the product warranty) After properly making the wire
nut connections, wrap the 7 connectors together with
electrical tape and push them into the lower right
FRUQHURIWKHFRQWUROER[RSHQLQJWRNHHSWKHPRXWRI
the way. Route the thermostat wiring out the bottom of
the opening at the notch and replace the metal cover.
Ventilation
To open the ventilation port, remove the adjustable air discharge louvers by gently pulling forward the right end until
it is released from the pivot point. Shift the louvers to the right to release the left end from its pivot point. To open the
ventilation port, pull the lever forward. The lever will lock in place. To replace the air discharge louvers, reverse the
above procedure
NOTE: When the thermostat is installed and power
is applied, the control display will not illuminate
and the unit is automatically controlled by the wall
thermostat.
NOTE: When using Wi-Fi, a remote wall thermostat
will not function. If a thermostat is installed, Wi-Fi
has operation priority.
Do Not Operate the unit in COOL mode when outdoor
temperatures are below 64ºF(18ºC).
Vent Door Open Vent Door Closed
Connector Wire Color Codes Thermostat Connections
Black Common
White Electric Heater
Yellow Compressor
Blue B terminal (heatpump models only)
Green Fan High
Tan Fan Low
Red 24 VAC
49-5000492 Rev. 4 7
WIFI SETUP
WiFi Setup
GE Appliances SmartHQ (for customers in the United States)
GE Appliances SmartHQ Enabled. If your Air Conditioner (AC) has a Connected Appliance Information label
located on the outside as shown below, your AC is GE Appliances SmartHQ Enabled. A WiFi
communication
card is built into the product allowing it to communicate with your smart phone for remote monitoring, control and
notifications. Please visit GEAppliances.com/connect to learn more about connected appliance features, and to learn
what connected appliance apps will work with your smart phone.
Network:
GE_MODULE_XXXX
MAC:
XXXXXXXXXXXX
FCC ID: ZKJ-WCATA006
IC: 10229A- WCATA006
Password:
XXXXXXXX
Network:
GE_MODULE_XXXX
MAC:
XXXXXXXXXXXX
FCC ID: ZKJ-WCATA006
IC: 10229A- WCATA006
Password:
XXXXXXXX
WiFi Connectivity: For assistance with the appliance or the ConnectPlus network connectivity (for models that are WiFi
enabled or WiFi optional), please call 1-800-220-6899.
8 49-5000492 Rev. 4
WIFI SETUP
WiFi Setup
How it Works
Download the GE Appliances App
8VHWKHDSSWRFRQQHFW\RXUURRPDLU
conditioner to WiFi
Once connected, use the app to turn
down your air conditioner as you
leave work.
CHANGE TEMP
TO 65
Getting Started
To connect your room air conditioner, you’ll need the GE
Appliances SmartHQ App. The app will walk you through
the connection process. Download the app from iTunes
or Google Play.
All connected appliance data is held in strict accordance
with the GE Appliances Connected Data Privacy Policy.
Visit geappliances.com/privacy/privacy_policy_
connected to view this policy.
Questions about SmartHQ
Get answers you need about setting up WiFi appliances
and connecting to your home network in our support
articles.
Visit products.geappliances.com/appliance/gea-
support-search-content to view wifi connect room air
conditioner support articles.
REGULATORY INFORMATION
FCC/IC Compliance Statement:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
&RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLRWHOHYLVLRQ
technician for help.
Labelling: Changes or modifications to this unit not
H[SUHVVO\DSSURYHGE\WKHPDQXIDFWXUHUFRXOGYRLGWKH
users authority to operate the equipment.
This product has Wi-Fi capability and requires
Internet connectivity and a wireless router to enable
interconnection with an Energy Management System,
DQGRUZLWKRWKHUH[WHUQDOGHYLFHVV\VWHPVRU
applications.
49-5000492 Rev. 4 9
CARE AND CLEANING
Care and Cleaning
How to Insert the Batteries in the Remote Control
1. Remove the battery cover by rotating it to the unlock
position.
2. Insert a new battery, making sure that the (+) and (-) of
the battery are installed correctly, (+) side up.
3. Reattach the cover by rotating it back into the lock
position.
NOTES:
8VH&59'&EDWWHU\'RQRWXVHUHFKDUJHDEOH
batteries.
Remove the battery from the remote control if the
V\VWHPLVQRWJRLQJWREHXVHGIRUDQH[WHQGHGSHULRG
of time.
Outdoor Coils
The coils on the outdoor side of the air conditioner
should be checked regularly.
If they are clogged with dirt or soot, they may need to
be professionally cleaned, a service available through
GE Appliances service or other service companies.
Front Grille Removal
The front grille can be removed for a more thorough
cleaning.
To remove:
1. Grasp the front grille louvers on both sides at the
recess and pull forward
2. Remove the filter by pulling forward and out.
3. Grasp the bottom of the grille and carefully pull
forward about 1” or until the security brackets limit the
travel forward.
4. Remove the two Phillips head screws located in the
upper corners of the grille louver opening.
5. Grasp the left and right rear edges of the grille about
6” from the top and pull outward to release the tabs
on the inside of the grille from the slots in each side of
the metal chassis cover. When released pull out both
bottom corners of the grill while carefully lifting up to
release the 4 tabs on the inside top of the grille from
the slots in the metal chassis cover
6. To release the multi-pin low-voltage electrical
connector from the user interface, press the rear of
the tab and gently pull apart.
Front Grille Re-installation:
1. Reconnect the multi-pin low voltage connector.
2. Before engaging the 4 tabs on the inside top of the
grille, align the ventilation lever on the chassis into
the mating slot on the inside of the discharge opening
in the grille. After ensuring proper alignment of the
ventilation lever, push the grille toward the chassis
and the tabs should snap into the slots on the metal
chassis cover.
Air filter
To access the filter, grasp the front grille louvers on both
sides at the recess and pull forward. Remove the filter by
lifting up and out. Note the filter direction when
re-installing.
Wash the filter using liquid dishwashing detergent and
warm water. Rinse the filter thoroughly. Gently shake
H[FHVVZDWHUIURPWKHILOWHU
Be sure the filter is thoroughly dry before replacing. Or,
instead of washing, you may vacuum the filter until clean.
NOTE: Never use hot water over 104°F (40°C) to clean
the air filter. Never attempt to operate the unit without the
air filter.
Energy Saving Note
,QRUGHUWRUHDFKPD[LPXPHQHUJ\VDYLQJDQGFRPIRUWLW
is recommended to use a cover to insulate the unit when
the unit is not in use. The recommended cover size for
WKHXQLWLV´[´[´:[+['
NOTE:8QSOXJWKHXQLWEHIRUHLQVWDOOLQJDFRYHU
Cabinet
Be sure to unplug the air conditioner to prevent shock or
fire hazard. The cabinet and front may be dusted with an
oil-free cloth or washed with a cloth dampened in a solution
of warm water and mild liquid dishwashing detergent.
Rinse thoroughly with a damp cloth and wipe dry.
1HYHUXVHKDUVKFOHDQHUVZD[RUSROLVKRQWKHFDELQHWIURQW
%HVXUHWRZULQJH[FHVVZDWHUIURPWKHFORWKEHIRUH
ZLSLQJDURXQGWKHFRQWUROV([FHVVZDWHULQRUDURXQG
the controls may cause damage to the air conditioner.
Plug in the air conditioner.
10 49-5000492 Rev. 4
INSTALLATION INSTRUCTIONS
Installation Instructions
For more help, visit GEAppliances.com
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT – Save these
instructions for local inspector’s use.
IMPORTANT – Observe all
governing codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the consumer.
Note to Consumer – Keep these instructions for
future reference.
Skill level – Installation of this appliance requires
basic mechanical skills.
• Completion time ±$SSUR[LPDWHO\KRXU
We recommend that two people install this
product.
Proper installation is the responsibility of the
installer.
Product failure due to improper installation is not
covered under the Warranty.
 <RX0867XVHSURSHULQVWDOODWLRQSURFHGXUHVDV
described in these instructions when installing this
air conditioner.
Power cord includes a current interrupter device. A
TEST and RESET button are provided on the plug
case. The device should be tested on a periodic
basis by first pressing the TEST button and then the
RESET button while plugged into the outlet. If the
TEST button does not trip or if the RESET button
will not stay engaged, discontinue use of the air
conditioner and contact a qualified service technician.
ELECTRICAL REQUIREMENTS
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
Do not change the plug on the power cord of this
air conditioner.
Aluminum house wiring may present special
problems—consult a qualified electrician.
For Existing Wall Sleeves
)RU([LVWLQJ:DOO6OHHYHV
Note that the air conditioner dimensions are:
Width-26”
Height-15 ¾”
Depth-18 ¼” (without front grille)
Depth-16” (rear of chassis to rear edge of front grille)
Install air conditioner according to these instructions
to achieve the best performance. Installing this air
FRQGLWLRQHULQH[LVWLQJVOHHYHVWKDWGRQRWDOORZIRU
proper fit or have proper outdoor grilles may affect
performance and could void the manufacturer’s
warranty.
Parts Included
• Security bracket and screws for a 26” wall sleeve (2)
• Remote Control (1)
IMPORTANT NOTE
For optimal energy efficiency and performance, we
recommend using the RAB26 or the RAB46B wall
sleeves with the RAG13A rear grille.
CAUTION
49-5000492 Rev. 4 11
INSTALLATION INSTRUCTIONS
Installation Instructions
Weather Seal Strips Installation
Ŷ7RLPSURYHVHDOLQJRQQRQ*(:DOO6OHHYHVRU
older wall sleeves that have damaged or missing
gaskets, we have provided two foam pads with
adhesive that can be installed on the sides of the
chassis per the below instructions.
Note: These gaskets may not be necessary with a
new RAB26A sleeve install.
1. Remove all packaging and packing material from
the unit.
2. Put the chassis on a table or install it
DSSUR[LPDWHO\ôRIWKHZD\LQWRWKHVOHHYH
3. Locate the “bump” or raised area in the metal on
each side of the unit right behind the front cover.
The foam strip should be located right behind the
raised area.
4. Wipe each side with a cloth to make sure the area
is clean.
5. Peel the backing off one piece of foam and starting
at the top corner of side, adhere it from top to
bottom just behind the bump on the flat surface.
6. Repeat on right side ensuring you do not put the
foam strip over the removable cover on the right
side.
7. When sliding the unit into the sleeve gently
compress the pads to help it move behind the
flange of the sleeve.
8. Be cautious of the foam pads when removing the
unit from the sleeve as well.
Security Brackets Installation
(It is important to install these brackets
to prevent the chassis from being
pushed into the room from the outside.)
Ŷ
The brackets must be installed so the flanges are
hooked behind the inside flanges of the wall sleeve.
8VLQJWKHVFUHZVSURYLGHGDWWDFKWKHEUDFNHWVRQ
the sides of the chassis.
To install the security bracket without fully removing
the front grille:
1. Grasp the front grille louvers on both sides at the
recess and pull forward.
2. Remove the filter by pulling forward and out.
3. Remove the two Phillips head screws located in
the upper corners of the grille louver opening. Do
not discard screws.
4. Grasp the left and right rear edges of the front
grille about 6” from the top and pull outward to
release the tabs on the inside of the grille from
the slots in each side of the metal chassis cover.
When released pull out both bottom corners of the
IURQWJULOOHDERXW´WRH[SRVHWKHWZRVFUHZKROHV
on the lower area of the metal chassis cover.
5. Locate the 2 metal brackets stamped 26” that were
included with the air conditioner. Hook the short
flange of the bracket behind the sleeve inside edge
and rotate it so the long side can be pressed flat
against the metal chassis cover. Adjust so the
bracket can be secured to the metal chassis cover
by 2 screws included with the bracket. Only one
bracket will be needed and can be installed on
either side of the chassis.
6. To reinstall the front grille, push the lower corners
to toward the sleeve until the side tabs click into
the mating slots. Reinstall the two screws removed
earlier and replace the filter and louvers.
For 26” sleeves, hook the short flange of the 26”
bracket behind the sleeve inside edge and secure
to the unit with the two screws provided. Repeat
on the opposite side.
Hook inside
sleeve edge
and secure
to unit
Hook inside
sleeve edge
and secure
to unit
Raised
Area
Locate foam
pad here
Removable
cover
Left Side
Right Side
12 49-5000492 Rev. 4
Troubleshooting Tips... Before you call for service
TROUBLESHOOTING TIPS
Problem Solution
Air conditioner does
not start
Wall plug disconnected. Push plug firmly into wall outlet.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type
or reset circuit breaker.
Plug current device tripped. Press the RESET button.
Power is OFF. Turn power ON.
Air from the unit does
not feel cold enough
Room temperature below 62°F (17°C). Cooling may not occur until room
temperature rises above 62°F (17°C).
Temperature sensor behind air filter may be touching cold coil. Keep it from the
cold coil.
Set to a lower temperature.
Compressor stopped when changing modes. Wait for 3 minutes after set to the
COOL mode.
Air conditioner cooling,
but room is too warm.
Ice is forming on
cooling coil behind
decorative front.
Outdoor temperature below 64°F (18°C). To defrost the coil, set FAN ONLY mode.
Air filter may be dirty. Clean the filter. Refer to Care and Cleaning section. To
defrost, set to FAN ONLY mode.
Thermostat set to cold for night-time cooling. To defrost the coil, set to FAN
ONLY mode. Then, set temperature to a higher setting.
Dirty air filter, or the air is restricted. Clean the air filter. Refer to Care and
Cleaning section.
Temperature is set too high. Set the temperature to a lower setting.
Air directional louvers positioned improperly. Position louvers for better air
distribution.
Front of unit is blocked by drapes, blinds, furniture, etc, which restricts air
distribution. Clear blockage in front of unit.
Doors, windows, registers, etc, may be open. Close doors, windows, registers.
Unit recently turned on in hot room. Allow additional time to remove “stored
heat” from walls, ceiling, floor, and furniture.
Air conditioner turns on
and off rapidly
Dirty air filter, the air is restricted. Clean air filter.
Outside temperature extremely hot. Set FAN speed to a higher setting to cool
outdoor cooling coil.
Noise when unit is
cooling
Air movement sound. This is normal. If too loud, set to a slower FAN setting.
Improper installation. Refer to installation instructions or check with installer.
Water dripping INSIDE
when unit is cooling
Improper installation. Tilt air conditioner slightly to the outside to allow water
drainage. Refer to installation instructions, and check with installer.
Water dripping
OUTSIDE when unit is
cooling
Unit removing large quantity of moisture from humid room. This is normal
during excessively humid days.
Room too cold Set temperature to low. Increase set temperature.
Error code “AS” in the
display
Room temperature sensor error. Unplug the unit and plug it back in. If error
repeats, call for service. NOTE: In Fan only mode, it will display “LO” or “HI”.
Error code “HS” in the
display
Electric heating sensor error. Unplug the unit and plug it back in. If error
repeats, call for service.
Error code “
” in the
display
Evaporator temperature sensor error. Unplug the unit and plug it back in. If
error repeats, call for service.
49-5000492 Rev. 4 13
Notes
14 49-5000492 Rev. 4
Notes
49-5000492 Rev. 4 15
GE Appliances Air Conditioner Limited Warranty
Staple your receipt here. Proof of the original purchase date
is needed to obtain service under the warranty.
LIMITED WARRANTY
ŶService trips to your home to teach you how to use
the product.
ŶImproper installation, delivery or maintenance. If you
have an installation problem, or if the air conditioner
is of improper cooling capacity for the intended use,
contact your dealer or installer. You are responsible
for providing adequate electrical connecting facilities.
ŶFailure of the product resulting from modifications
to the product or due to unreasonable use including
failure to provide reasonable and necessary
maintenance.
ŶIn commercial locations, labor necessary to move the
unit to a location where it is accessible for service by
an individual technician.
ŶReplacement of house fuses or resetting of circuit
breakers.
ŶFailure due to corrosion on models not corrosion-
protected.
ŶDamage to the product caused by improper power
supply voltage, accident, fire, floods or acts of God.
ŶIncidental or consequential damage caused by
possible defects with this air conditioner.
ŶDamage caused after delivery.
What GE Appliances Will Not Cover:
7KLVOLPLWHGZDUUDQW\LVH[WHQGHGWRWKHRULJLQDOSXUFKDVHUDQGDQ\VXFFHHGLQJRZQHUIRUSURGXFWVSXUFKDVHG
IRUKRPHXVHZLWKLQWKH86$,IWKHSURGXFWLVORFDWHGLQDQDUHDZKHUHVHUYLFHE\D*($SSOLDQFHV$XWKRUL]HG
Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an
$XWKRUL]HG*(6HUYLFHORFDWLRQIRUVHUYLFH,Q$ODVNDWKHOLPLWHGZDUUDQW\H[FOXGHVWKHFRVWRIVKLSSLQJRUVHUYLFH
calls to your home.
6RPHVWDWHVGRQRWDOORZWKHH[FOXVLRQRUOLPLWDWLRQRILQFLGHQWDORUFRQVHTXHQWLDOGDPDJHV7KLVOLPLWHGZDUUDQW\
gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: GE Appliances, a Haier company
Louisville, KY 40225
All warranty service must be provided by our Factory Service Centers, or an authorized Customer Care
®
technician.
To schedule service, visit us on-line at GEAppliances.com/service, or call 800.GE.CARES (800.432.2737). Have
serial number and model number available when calling for service. In Canada, contact your distributor.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this
Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a
particular purpose, are limited to two years or the shortest period allowed by law.
For The Period Of: GE Appliances Will Replace:
Two Years
From the date of the
original purchase
GE Appliances Will Replace: Any part of the air conditioner which fails due to a defect in
materials or workmanship. During this limited two-year warranty, GE Appliances will also
provide, free of charge, all labor and related service to replace the defective part.
Five Years
From the date of the
original purchase
GE Appliances Will Replace: Any part of the sealed refrigerating system (the compressor,
condenser, evaporator, reversing valve, and all connecting tubing) which fails due to a defect
in materials or workmanship. During this three-year additional warranty, GE Appliances will
also provide, free of charge, all labor and related service to replace the defective part.
16 49-5000492 Rev. 4
Printed in China
Consumer Support
GE Appliances Website
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day
of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support
VHUYLFHVGHVLJQHGIRU\RXUFRQYHQLHQFH,QWKH86GEAppliances.com In Canada, contact your distributor.
Register Your Appliance
Register your new appliance on-line at your convenience! Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise. You may also mail in
WKHSUHSULQWHGUHJLVWUDWLRQFDUGLQFOXGHGLQWKHSDFNLQJPDWHULDO,QWKH86GEAppliances.com/register
Schedule Service
([SHUW*($SSOLDQFHVUHSDLUVHUYLFHLVRQO\RQHVWHSDZD\IURP\RXUGRRU*HWRQOLQHDQGVFKHGXOH\RXUVHUYLFHDW
\RXUFRQYHQLHQFHDQ\GD\RIWKH\HDU,QWKH86GEAppliances.com/service or call 800.432.2737 during normal
business hours.
For Canadian customers, call your distributor for service and/or replacement parts.
Extended Warranties
3XUFKDVHD*($SSOLDQFHVH[WHQGHGZDUUDQW\DQGOHDUQDERXWVSHFLDOGLVFRXQWVWKDWDUHDYDLODEOHZKLOH\RXU
warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your
ZDUUDQW\H[SLUHV,QWKH86GEAppliances.com/extended-warranty or call 800.626.2224 during normal
business hours.
For Canadian customers, contact your distributor.
CONSUMER SUPPORT
Parts and Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.
,QWKH86GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing
generally should be referred to qualified service personnel. Caution must be exercised, since improper
servicing may cause unsafe operation.
For Canadian customers, contact your distributor.
Contact Us
If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the
details including your phone number, or write to:
,QWKH86*HQHUDO0DQDJHU&XVWRPHU5HODWLRQV_*($SSOLDQFHV$SSOLDQFH3DUN_/RXLVYLOOH.<
GEAppliances.com/contact
For Canadian customers, contact your distributor.
Transcrivez les numéros de modèle
et de série ici :
# de modèle _____________
# de série _______________
Vous trouverez l’étiquette
signalétique sur le côté du
climatiseur.
GE est une marque déposée de General Electric Company. Fabriqué sous licence de marque.
Le climatiseur
Climatiseur 26 po avec Wi-Fi intégré
49-5000492 Rev. 4 02-21 GEA
INFORMATION DE SÉCURITÉ ...3
UTILISANT LE CLIMATISEUR ..4
CONFIGURATION
DU WI-FI ...........................7
ENTRETIEN ET NETTOYAGE ....9
INSTRUCTIONS
D’INSTALLATION
.............. 10
CONSEILS DE DÉPANNAGE ....12
SOUTIEN AU CONSOMMATEUR
Garantie limitée ......................13
Soutien au consommateur .............14
MANUEL D’UTILISATION
ET INSTRUCTIONS
D’INSTALLATION
Modèles Cool uniquement
AJCQ06LWH
AJCQ08AWH
AJCQ10AWH
AJCQ10DWH
AJCQ12AWH
AJCQ12DWH
AJCQ14DWH
Modèles à montage surélevé
uniquement cool
AJCM08AWH
AJCM10AWH
AJCM10DWH
AJCM12DWH
Modèles chaud / froid
AJEQ08AWH
AJEQ10DWH
AJEQ12DWH
AJEQ14DWH
Modèles à montage haut chaud /
froid
AJEM12DWH
Modèles de pompes à chaleur
AJHQ08AWH
AJHQ12DWH
2 49-5000492 Rev. 4
NOUS VOUS REMERCIONS D’ACCUEILLIR GE APPLIANCES CHEZ VOUS
Que vous ayez grandi avec GE Appliances ou qu’il s’agisse de votre première acquisition, nous
sommes heureux de vous accueillir dans notre famille.
Nous sommes fiers du savoir-faire, de l’innovation et de l’esthétique qui composent chaque appareil
GE Appliances, et nous pensons que vous le serez aussi. Dans cette optique, nous vous rappelons
que l’enregistrement de votre électroménager vous assure la communication de renseignements
importants sur le produit et la garantie lorsque vous en avez besoin.
Enregistrez votre électroménager GE en ligne dès maintenant. Des sites Web et des numéros de
téléphone utiles figurent dans la section Soutien au consommateur de ce manuel d’utilisation.
49-5000492 Rev. 4 3
Pour votre sécurité, vous devez suivre les instructions de ce manuel pour
réduire les risques d’incendie, d’explosion, de choc électrique, de dommage à
la propriété, de blessure ou de décès.
Ŷ1¶XWLOLVH]FHWDSSDUHLOTXHSRXUVRQXVDJHSUpYXWHO
que décrit dans le Manuel de l’utilisateur.
Ŷ9RXVGHYH]ELHQPRQWHUFHFRQGLWLRQQHXU
conformément aux Instructions de montage, avant de
l’utiliser.
Ŷ1HGpEUDQFKH]MDPDLVYRWUHFRQGLWLRQQHXUHQWLUDQW
sur le cordon d’alimentation. Saisissez fermement la
fiche et sortez-la droit de sa prise.
Ŷ5HPSODFH]LPPpGLDWHPHQWWRXWFRUGRQG¶DOLPHQWDWLRQ
abîmé ou endommagé. Un cordon d’alimentation
électrique endommagé ne doit pas être réparé mais
plutôt remplacé par un autre cordon d’alimentation
obtenu du fabricant. N’utilisez pas un cordon
d’alimentation qui montre des fissures ou des signes
d’abrasion sur sa longueur ou encore près de la prise
ou du connecteur.
ŶeWHLJQH]HWGpEUDQFKH]YRWUHFOLPDWLVHXUDYDQWGH
procéder à une réparation ou un nettoyage.
Ŷ3RXUYRWUHVpFXULWp«QHUDQJH]MDPDLVRXQ¶XWLOLVH]
MDPDLVGHVPDWpULDX[FRPEXVWLEOHVGHO¶HVVHQFH
ou d’autres vapeurs ou liquides inflammables à
proximité de cet appareil ou de tout autre appareil
électroménager.
Ŷ6LODSULVHpOHFWULTXHQ¶HVWSDVFRPSDWLEOHDYHFOD
fiche du cordon électrique, il faut faire remplacer la
prise par un électricien agréé.
UTILISATION DE RALLONGES
RISQUE D’INCENDIE. Peut occasionner des
blessures graves ou la mort.
Ŷ1(3$6XWLOLVHUGHUDOORQJHDYHFFHFRQGLWLRQQHXU
d’air.
Ŷ1(3$6XWLOLVHUGHSDUDVXUWHQVHXURXG¶DGDSWDWHXUj
prises multiples avec ce conditionneur d’air.
COMMENT BRANCHER L’ÉLECTRICITÉ
1HFRXSH]RXQ¶HQOHYH]MDPDLVODEURFKHGHPLVHj
la terre (la troisième broche de la fiche) du cordon
G¶DOLPHQWDWLRQ3RXUYRWUHVpFXULWpSHUVRQQHOOHFHW
appareil doit être bien mis à la terre.
N’utilisez PAS une fiche d’adaptation avec cet
électroménager.
Le cordon d’alimentation de cet appareil est muni d’une
fiche triphasée (mise à la terre) qui correspond à une
prise murale normale triphasée, pour réduire le danger
de secousse électrique.
Le cordon d’alimentation peut comprendre un
mécanisme d’interruption de courant. Un bouton d’essai
et de remise en marche est fourni sur le boîtier de la
SULVH9RXVGHYH]HVVD\HUOHPpFDQLVPHSpULRGLTXHPHQW
en appuyant d’abord sur le bouton TEST (essai) puis
sur le bouton RESET (remise en marche). Si le bouton
TEST ne bascule pas ou si le bouton RESET ne reste
pas enfoncé, cessez d’utiliser votre conditionneur d’air et
appelez un technicien de service qualifié.
Faites vérifier la prise murale et le circuit électrique par
un électricien qualifié pour vous assurer que la prise est
bien à la terre.
Si vous avez une prise biphasée, vous êtes
personnellement responsable et obligé de la faire
remplacer par une prise murale triphasée bien mise à la
terre.
9RXVGHYH]WRXMRXUVEUDQFKHUOHFRQGLWLRQQHXUGDQVVD
propre prise électrique, d’un voltage qui correspond à la
plaque signalétique.
Cela vous permettra d’obtenir le meilleur rendement et
empêchera la surcharge des circuits électriques de la
maison, qui risque d’occasionner un danger d’incendie.
Consultez les Instructions de montage, section des
Exigences électriques, pour les exigences de
branchements électriques particuliers.
INFORMATION DE SÉCURITÉ
INFORMATION DE SÉCURITÉ IMPORTANTES
LISEZ TOUTES LES DIRECTIVES AVANT D'UTILISER L'APPAREIL
LIRE ET CONSERVER CES INSTRUCTIONS
AVERTISSEMENT
AVERTISSEMENT
4 49-5000492 Rev. 4
Commandes du climatiseur
L’aspect peut varier.
Ŷ3RXUVRQERQIRQFWLRQQHPHQWGLULJH]ODWpOpFRPPDQGHYHUV
le récepteur de signal sur le climatiseur.
Ŷ/HVLJQDOGHODWpOpFRPPDQGHDXQHSRUWpHGHMXVTX¶j
pieds.
Ŷ/DWpOpFRPPDQGHFRQWU{OHO¶DSSDUHLOPrPHVLFHOXLFLHVW
connecté au Wi-Fi.
Ŷ$VVXUH]YRXVTX¶DXFXQREMHWQHEORTXHOHVLJQDOHQWUHOH
climatiseur et la télécommandel.
Ŷ$VVXUH]YRXVTXHODFKDUJHGHODSLOHHVWVXIILVDQWHHWTXH
FHWWHGHUQLqUHHVWFRUUHFWHPHQWLQVWDOOpH²9R\H]ODVHFWLRQ
Entretien et nettoyage.
Télécommande
Les témoins lumineux au-dessus des touches sur le panneau de
commande du climatiseur indiquent les réglages choisis.
Utilisant le climatiseur - Commandes
UTILISANT LE CLIMATISEUR
1. POWER (Mise sous/Hors tension)
Allume ou éteint le climatiseur.
2. DISPLAY (Afficher)
Affiche le réglage de température.
3. MODE
Utilisez cette option pour accéder aux modes HEAT (certains
PRGqOHV&22/)$1(&2RX'5</HVWpPRLQVOXPLQHX[
des commandes indiqueront le mode sélectionné.
4.
TOUCHES D’AUGMENTATION (+) / DIMINUTION (-) DE LA
TEMPÉRATURE
Utilisez cette option pour accéder aux modes HEAT (certains
PRGqOHV&22(&2RX'5</HVWpPRLQVOXPLQHX[GHV
commandes indiqueront le mode sélectionné.
5. FAN SPEED (Vitesse du ventilateur)
Cette option permet de régler la vitesse du ventilateur à AUTO,
LOW, MEDIUM ou HIGH. Les témoins lumineux indiqueront la
vitesse sélectionnée.
6. FILTER (Filtre)
Enregistre le temps de fonctionnement cumulé du ventilateur
pour rappeler de nettoyer le filtre.
7. WI-FI
Cet électroménager est compatible avec la connectivité Wi-Fi
de GE Appliances.
8. SLEEP (Veille)
Cette option permet à la température ambiante d’augmenter (en
mode Cool) ou de diminuer (en mode Heat) pendant les heures
de sommeil.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

GE AJCM08AWH Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues