GE AEE08ASL1 Le manuel du propriétaire

Marque: GE

Modèle: AEE08ASL1

Taper: Le manuel du propriétaire

ge.com

Safety Instructions . .......... 2, 3

Operating Instructions ......... 4, .5

Care and Cleaning

Air Fiher ...................... 5

Grille and Case ................. 5

Outdoor Coils .................. 5

Installation Instructions

Through-the-Wall

Installation--Optional .......... 12

Window Installation .......... 7-11

Troubleshooting Tips ....... 14, 15

Consumer Support

Consumer Support ..... Back Cover

Ownership Registration for

Customers in Canada only .... 15, 16

Warranty fbr Customers

in Canada .................... 17

Warranty for Customers

in the U.S.A ................... 18

AEE 0 8

AEE12

Climatiseur

La section fran(aise commence ?zla page 19

Acondicionador

de aire

La seccidn en espa_,ol empieza en la pdgina 35

Writethemodelandserial numbershere:

Model #

Serial #

Find these numbers on a label on the

side of the air condifione_.

In Canada, contact us at:

xs_s_u.GEAppliances.ca

49-7611 12-08Jfl

IMPORTANTSAFETYINFORMATION.

READALLINSTRUCTIONSBEFOREUSING.

WARNING!

Foryour safety, the information in this manual must be followed to minimize the risk of fire, electric shock

or personal injun/

SAFETYPRECAUTIONS

iiiil}i

iii}i}}li_

Use this appliance only fbr its intended

purpose as described in this Owner's

Manual.

This air conditioner must be properly

installed in accordance Mth the Installation

Instructions before it is used.

Never unplug your air conditioner by pulling

on the power cord. Always grip plug firmly

and pull straight out fiom the receptacle.

Replace immediately all electric service

cords that have become fiayed or otherwise

damaged. A damaged power supply cord

must be replaced with a new power supply

cord obtained fiom the manufacturer and

not repaired. Do not use a cord that shows

cracks or abrasion damage along its len_h

or at either the plug or connector end.

}} If the receptacle does not match the plug,

the receptacle must be changed out by a

qualified electrician.

}} Turn the unit OFFand unplug your air

conditioner before making any repairs

or cleaning.

NOTE: Westronglyrecommendthatanyservicing

be performedbya qualified individual.

_:_For your safety...do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the x,icinity

of this or any other appliance.

_:_All air conditioners contain refiigerants,

which under federal law must be removed

prior to product disposal. Ifyou are getting

rid of an old product with refrigerants,

check with the company handling disposal

about what to do.

HOWTOCONNECTELECTRICITY

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord. For

personal safety, this appliance must be properly

grounded.

DO NOT usean adapter plug with this appliance.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall

outlet to minimize the possibility of electric

shock hazard from this appliance.

Power cord includes a current intermpmr

dex,ice. A test and reset button is prox,ided on

the plug case. The dex,ice should be tested on a

periodic basis by first pressing the TESTbutton

and then the RESETbutton. If the TESTbutton

does not trip or if the RESETbutton will not

stay engaged, discontinue use of the air

conditioner and contact a qualified ser\,ice

mchnician.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly _ounded.

Where a 2-prong wall outlet is encounmred,

it is your personal responsibility and obligation

to have it replaced with a properly grounded

3-prong wall outlet.

The air conditioner should always be

plugged into its own individual electrical

outlet which has a voltage rating that matches

the rating plate.

This prox,ides the best performance and also

prevents overloading house xdring circuits

which could cause a fire hazard from

overheated Mres.

See the Installation Instructions, Electrical

Requirements section for specific electrical

connection requirements.

ge.com

WARNING!

CORDS--115-Volt modelsonl

Because of potential safety hazards under certain

conditions, we strongly recommend against the

use of an extension cord.

However; if you must use an extension cord,

it is absolutely necessa U that it be a UL-listed,

14 gauge, 3_wiregrounding type appliance

exmnsion cord ha\,ing a grounding type plug

and outlet and that the electrical rating of the

cord be 15 amperes (minimum) and 125 volts.

CAUTION:

DONOT usean extension cord with anyof the

230/208 volt models.

READANDFOLLOWTHISSAFETYINFORMAtiONCAREFULLY

SAVETHESEINSTRUCTIONS

Aboutthe controlsontheair conditioner.

Features and appearance will vary.

5 6

K ,,go

Warmer Cooler

TEMPCONTROL

off

Hi h _ % Hi

Low\\ I I J/Low

Heat __J Cool

Fan

Only

MODECONTROL

Controls

TempControl

The temp control is used to maintain the

room temperature. The compressor will

cycle oi1 and off to keep the rooln at the

same level of comfort. Turn the knob

clockwise to Cooler (blue) and the indoor

air will become cooler. Turn the knob

counterclockwise to Warmer(red) and

the indoor air will become warmeL

Mode Control

Hi Cooland Low Coolprovide cooling with

different fan speeds.

Hi Heatand Low Heatprovide heating with

dift>rent fan speeds.

FanOnlysetting provides air circulation

and filtering without cooling or heating.

NOTE:If youmovethemodecontrolfroma

coolsettingtoOff,a fansettingora heat

setting,wait atleast3 minutesbeforeswitching

backtoa coolsetting.

Cooling Descriptions

ForNormal Cooling--Select Hi Cool

or Low Coolwith the temp control at

midpoint.

For Maximum Cooling-Select Hi Cool with

the temp control turned clockwise as far

as possible.

For Quieter and Nighttime Cooling--Select

Low Coolwith the temp control at

midpoint.

Heating Descriptions

For Normal Heating--Select Hi Heat

or Low Heatwith the temp control at

midpoint.

ForMaximumHeating--Select Hi Heatwith

the temp control turned counterclockwise

as far as possible.

ForQuieter& Nighttime Heating--Select Low

Heatwith the temp control at midpoint.

Additional important information.

Air Direction

Use the lever to adjust the air direction left and

right onl):

Fingertip pressure on the horizontal louvers

adjusts the air direction up or down.

ge.com

Careand cleaningoftheair conditioner.

Grille and Case

Turn the air conditioner off and remove the plug To clean, use water and a miM detergent.

flom the wall outlet before cleaning. Do not use bleach or abrasives.

Air Filter

The air filter behind the front grille should be

checked and cleaned at least eve_y 30 dws or

more often if necessary.

Toremove:

Push on one side of the filter edge and pull it out

the other side.

Glean the filter with warm, soapy wateL Rinse and

let the filter dry before replacing it. Do not clean

the filter in a dishwasheL

^,.CAUTION:DoNoToperatetheairconditioner

withoutafilterbecausedirtandlintwillclog

it andreduceperformance.

Outdoor Coils

The coils on the outdoor side of the air conditioner

should be checked regularly. If they are clogged

with dirt or soot, they may be professionally cleaned.

ilnsta,,at,onnstruct,onsl'irC°ndit'°nerl

IF_ Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: ge.com I

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer- Be sure to leave these

instructions with the Consumer.

• Note to Consumer- Keep these

instructions for future reference.

• Skill level -Installation of this appliance

requires basic mechanical skills.

• Completion time- Approximately 1 hour

• We recommend that two people install

this product.

• Proper installation is the responsibility

of the installer.

Product failure due to improper installation

is not covered under the Warranty.

You MUST use all supplied parts and use

proper installation procedures as described

in these instructions, and any separate kit

instructions, when installing this air

conditioner.

O ELECTRICAL REQUIREMENTS

(_ Some models require a 115/120-volt a.c.,

60 Hz grounded outlet protected with a

15-amp time delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the

possibility of electric shock hazard. If the wall

outlet you plan to use is only a 2-prong outlet,

it is your responsibility to have it replaced with

a properly grounded 3-prong wall outlet.

Some models require 230/208-volt a.c.,

protected with a time delay fuse or circuit

breaker.These models should be installed

on their own single branch circuit for

best performance and to prevent

overloading house or apartment wiring

circuits, which could cause a possible fire

hazard from overheating wires.

-&CAUTION:

Do not, under any circumstances, cut or

remove the third (ground) prong from the

power cord.

Do not change the plug on the power cord

of this air conditioner.

Aluminum house wiring may present special

problems--consult a qualified electrician.

If the sill support bolts do not contact the

window sill, or if you have a window

without a sill, you must order accessory kit

RAK87 to properly install this air conditioner.

Call 800.626.2002 or visit ge.com.

TOOLS YOU WILL NEED

Phillips-head screwdriver

Adjustable wrench

Pencil

Level

Flat-blade screwdriver

Ruler or tape measure

Scissors or knife

Power cord includes a current interrupter

device. A test and reset button is provided on

the plug case.The device should be tested on a

periodic basis by first pressing the TEST button

and then the RESET button. If the TEST button

does not trip or if the RESET button will not stay

engaged, discontinue use of the air conditioner

and contact a qualified service technician.

Window Installation Instructions

PARTS INCLUDED

(appearance may vary)

Foam top

window gasket

Left

accordion.

panel

Sill support (2)

Nut (2)

Bolt (2)

Top mounting rail

Case bottom seal

(thin, adhesive-backed)

Right

accordion

panel

Type A (6) Type B (7) Type C (6)

Type D (3)

Window locking

bracket (2)

Window Installation Instructions

ITI WINDOW REQUIREMENTS

• These instructions are for a standard

double-hung window.You will need to

modify them for other types of windows.

CAUTION: If the sill support

bolts do not contact the window sill or

if you have a window without a sill, you

must order accessory kit RAK87 to

properly install this air conditioner.

Call 800.626.2002 or visit ge.com.

All supporting parts must be secured

to firm wood, masonry or metal.

The electrical outlet must be within

reach of the power cord.

17" min.

27" to 36"

(With accordion panels)

i i

[] STORM WINDOW REQUIREMENTS

A storm window frame will not allow the

air conditioner to tilt toward the outside,

and will keep it from draining properly.

To adjust for this, attach a piece of wood

to the stool.

WOOD PIECES-

WIDTH: 2"

LENGTH: Long enough to fit inside the

window frame.

THICKNESS: To determine the thickness,

place a piece of wood on the stool to

make it 1/2" higher than the top of the

storm window frame or the vinyl frame.

Attach securely with nails or screws

provided by the installer.

1/2" higher

than vinyl frame

L (on some windows)

1/2"higher _______ _Wood

than storm

window !1

frame _St°°l FT _

Storm window

frame - r_ Vinyl frame ] ]

[] REMOVE THE AIR CONDITIONER

FROM THE CASE

IA] Remove and save the 2 screws from the

lower sides of the front grille.

FRONT

[] Remove the two control knobs.

FRONT

Grasp the lower corners of the grille while

pressing in on the case sides with your

finger tips. Pull out to release and lift it up.

NOTE: Do not pull the bottom edge

toward you more than 3" or you may

damage the tabs of the grille.

t t

FRONT

r_ Remove the screw from each side of the

case. Keep them in a safe location.

FRONT

Window Installation Instructions

13] REMOVE THE AIR CONDITIONER

FROM THE CASE (CONT.)

[] Remove and save the ground wire screw.

[i.

GroundL_

wire _

Ground

screw

Illl++ll

IUl#{I

IllllJll

IIl_ltll

iiIlm+

IIMII+

II_llll+

_Jllll+

_ FRONT

r_ Slide the air conditioner from the case by

gripping the base pan handle and pulling

forward while bracing the case. Do not

pull or lift on the styrofoam discharge area.

Do not

pull or

lift in

this

area-

damage

to the

unit may

result

FRONT

_] INSTALLTHE BOTTOM

CASE SEAL

• Peel the backing from the bottom

case seal and attach it along the

bottom of the case in front of the

bottom mounting rail.

Bottom

mounting

Bottom case seal

I-5]INSTALL THE TOP MOUNTING

RAIL ONTO THE CASE

Attach the top mounting rail onto the top

of the case with 3Type B screws.

Press firmly to drive the screws into the

gasket and through the top mounting rail.

3e B

screws

[] INSTALL THE

SIDE ACCORDION PANELS

IA1 Slide the left and right accordion panels

into the top and bottom mounting rails.

r_ Attach the accordion panels to the case

using 3Type A screws on each side.

Top mounting rail

Accordion

panel

Type A

screws

BACK

Bottom mounting rail

Window Installation Instructions

1711NSTALLTHE CASE IN THE

WINDOW

[_] Open the window and mark the centerline of

the window stool.

['_ Carefully place the case on the window stool

and align the center mark on the bottom front

with the centerline of the stool.

['_ Pull the window down behind the top

mounting rail.

NOTE: Do not shut the window so tightly that

movement of the accordion panels is

restricted.

['_ Select the position that will place the sill

supports near the outermost point on the sill.

Place the short side of the sill supports, on the

case bottom, toward the window. Attach the

sill supports to the case track hole in relation

to the selected position using 2Type B screws

in each support.

-&CAUTION: Do not install this air

conditioner in a window if the bolts do not

contact the window sill.

I I

Long side

of sill

supports

OUTSIDE

['_ Adjust the bolt and the nut in

each support so that the case is installed with

a slight tilt to the outside. Use a level; no more

than 1/2 bubble will be the correct case slant

to the outside.

-& CAUTION: Ifthesillsupport bolts

do not contact the window sill or ifyou have a

window without a sill you must order accessory

kit RAK87 to properly install this air conditioner.

Call 800.626.2002 or visit ge.com.

[] INSTALLTHE CASE INTHE

WINDOW (CONT.)

['_ Secure the case to

the window stool

by using

3Type D screws. Sill _ ]_

support

Pull the accordion

i1.-i

panels to each

window sash track.

Attach them on each

side to the window

sash and the window

stool using

4Type C screws.

1-81SECURE THE CASE IN THE

WINDOW AND INSTALL THE

FOAM TOP WINDOW GASKET

IA].&CAUTION:

To prevent broken glass

or damage to windows,

on vinyl or other

similarly constructed

windows, attach the

support bracket to the

window side jam.

Vinyl

Attach the window

locking brackets

(one on each side)

with Type C screws.

Wood

[]

Cut the foam top window gasket to the

window width.

Stuff the foam

between the glass

and the window to

prevent air and

insects from

getting into the

room.

NOTE: If the gasket supplied does not fit your

window, obtain appropriate material locally to

provide a proper installation seal.

Window Installation Instructions

_-I INSTALL THE AIR CONDITIONER

IN THE CASE

Slide the air conditioner into the case by

the base pan. Do not push on the controls,

styrofoam air discharge housing or the finned

coils. Make sure the air conditioner is firmly

seated.

Do not press on

these areas-

damage to the

unit may result

BasePan

r_ Replace the 2 screws removed earlier, one

on each side of the case.

r_ Reattach the ground wire to the unit using

the ground wire screw.

Ground

screw

_-I INSTALL THE AIR CONDITIONER

IN THE CASE (CONT.)

FD] Attach the front grille to the case by inserting

the tabs on the grille into the slots on the

front top of the case. Push the grille in.

Secure the front grille to the case by

replacing the 2 screws removed earlier.

Press on the top of the grille to help with

side screw installation.

r_ Replace the two control knobs.

rG-] Connect power.

Through-the-Wall Installation Instructions--Optional

The case may be installed through-the-wall

in both existing and new construction.

Read completely, then follow step-by-step.

NOTE: Obtain all materials locally for

mounting the air conditioner through-

the-wall.

m IMPORTANT (cont.)

[] Secure with 14 wood screws anchored at

least an inch into the wall support structure.

NOTE: Drill pilot holes, if necessary, for

proper installation. If the frame is oversized,

use shims to prevent case distortion.

ITI IMPORTANT

Through-the-wall installation is not

appropriate if any of the side or top louvers

in the case will be obstructed by the wall.

All side and top louvers in the case must

project on the outdoor side of the wall.

The room side of the case must project

into the room far enough to maximize the

balance of the unit.

The case must be installed level from side-

to-side and with a slight tilt from front to

rear. Use a level; no more than a 1/2 bubble

will be the correct case slant to the outside.

Lintel angle is required to support bricks or

blocks above opening.

Flashing is required and should extend the

length of the opening to ensure no inside

cavity leakage occurs.

[] Remove the air conditioner from the case.

For specific instruction, refer to the Window

Installation Instructions.

[] Make certain that a wall receptacle is

available close to the hole location or make

arrangements to install a receptacle.

! ,

Place the case in the wall opening and

place wood support strips between the case

bottom and the flashing on both sides of the

bottom rail.They should be the same height

as the bottom rail and the same length as

the wall opening.

[] FINISH THE WALL OPENING

[] Caulk all four sides on the outdoor side of

the case to prevent moisture from getting

through to the interior wall. Use of flashing

(drip rail) will further prevent water from

dripping inside the wall and down the

outside of the building.

Plaster line

Trim molding

(if desired)

INSIDE

Bottom rail

Wood filler and

caulking (above

and below the

flashing)

Flashing

(Drip rail)

Bottom

rail

Flashing

(Drip rail)

Wood support strips

_] Place the air conditioner into the case.

For specific instruction, refer to the Window

Installation Instructions.

Beforeyoucall forservice...

Troubleshooting tips

Save time and money! Review the chart below first

and you may not need to call for service.

ge.com

Possible Causes What ToDo

Air conditioner The air conditioner * Make sure the air conditioner plug is pushed completely

does not start is unplugged into the outlet.

The fuse is blown/circuit • Gheck the house flise/circuit breaker box and replace

breaker is tripped the flise or reset the breakeL

Power failure * The unit will automatically re-start in the settings last

used after file power is restored.

• There is a protective time delay (approximately

3 minutes) to prevent tripping of the compressor

overload. For this reason, the unit may not start

normal cooling or heating for 3 minutes after it

is unned back on.

The current interrupter

device is tripped

*Press the RESETbutton located on the power cord plug.

*If the RESETbutmnwill not stay engaged, discontinue

use of the air conditioner and contact a qualified selMce

mclmician.

Air conditioner Ice blocks the air flow * Set the mode conuol at Fan Onlyor Hi Coolwifll file

freezing up and stops the air conditioner temp control at a wamler setting.

from cooling the room

Air conditioner does not Airflow is restricted * Make sure there are no curtains, blinds or flnnimre

cool as it should blocking file flont of file air condifioneL

The temp control may * Turn file temperature knob clockwise as far _tspossible.

not be set correctly

The air filter is dirty * Glean the filter at least eve_y 30 days. See the Operating

Instructions section.

The room may have been hot *When file air conditioner is fi]st unned on you need

to allow time for file room to cool down.

Cold air is escaping * (;heck for open flnnace floor regfiste_s and

cold air reuirns.

• Set the air conditioner's vent m the closed position.

Cooling coils have iced up * See "Air conditioner freezing up"above.

Air conditioner does not Airflow is restricted • Make sure fllere are no curtains, blinds or furniune

warm as #should blocking file flont of file air condifioneL

The temp control may * Turn the knob counterclockwise as far as possible.

not be set low enough The lowest setting provides maxinauln warming.

The air filter is dirty * (_lean the filter at least eve_y 30 days. See the Operating

Instructions section.

The room may have been cold *When file air conditioner is fi_st turned on, you need to

allow time for file room to warm lip.

Warm air is escaping * Check for open finnace floor reg,iste_s and

cold air reuirns.

Beforeyoucall forservice...

Troubleshooting tips

Waterdripsoutside

Possible Causes

Excessively hot and

humid weather

What ToDo

• This is normal.

Water drips indoors The air conditioner is not • For proper water disposal, make sure the air conditioner

tilted to the outside slants slightly flom the case flont to the real

Watercollectsin

basepan

Moisture is removed from

indoor air and drains into

rear of a cabinet where a fan

blows it against the outdoor

condenser coil

• This is normal for a short period in areas with

little humidity; normal for a longer period in very

humid areas.

Please place in envelope and mail to:

Veuillez mettre dans une enveloppe et envoyez _ :

OWHERSHJPREGJSTRATJOH

P.O. BOX1780

MISSISSAUGA,OHTARIO

L4Y4G1

(FORCAHADJAHCOHSUMERSOHLY)

I,i,I

For Canadian

Customers

Pour les

Consommateurs

Canadiens

ec"

e¢"

£3

Pleaseregisteryourproducttoenabbustocontactyou

intheremoteeventasafetynoticeisissuedforthisproduct

and to allow for efficient communication under the terms

of your warranty, should the need arise.

REGISTERON-UNE: www.geappliances.ca

ENREGISTREMENTSUR INTERNETA: wvvw.electromenagersge.ca

[] MP_/M [] MRS./MME. FIRSTNAME/PRI'NOM[] MISS/MLLE.[] MS.

STREETNO/N° RUE STREETNAME/ RUE

CITY/VILLE

AREACODE/ IND.RING.JTELEPHONE _E-MAIL

DIDYOUPURCHASEASERVICECONTRACTFORTHISAPPLIANCE?

AVEZ-VOUSACHETEUNCONTRATDESERVICEPOURCETAPPAREIL?

Veuillezenregi_ervo_eproduitafindenousperrne_ede

communiqueravecvoussijamaisunavisdes6curft6concemant

ceproduit6tait6misetdecommuniquerfacibmentavecvousen

ve_ devotregarage,silebesoins'enfaitserdr.

P.O.BOX1780,MISSISSAUGA

ONTARIO,L4Y461

MAILTO:

POSTER,_:

LASTNAME/NOM

AP%NO/APR/RR#

PROVINCE POSTALCODE/ POSTAL

YES/OUI [] IFYES/ SIOUl:EXPIRATION

Y/A M D/J

NO/NON []

NAME OFSELLINGDEALER/NOMDU MARCHAND MODEL / MODt_LE

INSTALLA'I1ONDATE/DATED'INSTALLA]ION

Y/A M D/J CORRESPONDENCE [] ENGLISH

CORRESPONDANCE [] FRAN?AIS SERIAL/St_RE

[] Ido notwishtoreceiveanypromotionaloffersregardingthisproduct.

[] Je ned_sirepasrecevoird'offrespromotionnellesconcernantceproduit

GEAir Conditioner--One- YearLimited Warranty.(For customers in the U.S.A.)

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care_ technician. Toschedule service,

visit us on-line at ge.com, or call 800.GE.CARES(800.432.2737).

Have serial number and model number available when calling

for service.

Staple your receipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

Fromthedateof the

originalpurchase

GE Will Replace:

Anypartof file ah conditioner which fails due to a defect in mmerials or workmanship.

During this limited one-year warranty, GE will also provide, free of charge, all labor and related

se_Mce to replace the defective part.

Service trips to your home to teach you how to

use the product.

Replacement of house fuses or resetting of circuit

breakers.

Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner

is of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible

for providing adequate electrical connecting facilities.

Failure of the product resulting from modifications to

the product or due to unreasonable use including failure

to provide reasonable and necessary maintenance.

Failure due to corrosion on models not corrosion-

protected.

Damage to the product caused by improper power supply

voltage, accident, fire, floods or acts of God.

Incidental or consequential damage caused by possible

defects with this air conditioner.

Damage caused after delivery.

In commercial locations, labor necessary to move the

unit to a location where it is accessible for service

by an individual technician.

EXCLUSION OFIMPLIED WARRANTIES--Your sole and exclusive remedy is product repair as provided in this

Limited Warranty.Any implied warranties, including the implied warranties of merchantability or fitness for a

particular purpose, are limited to one year or the shortest period allowed by law.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home

use within the USA. If the product is located in an area where service by a GEAuthorized Servicer is not available,

you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service

location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. Toknow what your

legal rights are, consult your local or state consumer affairs office or your state's Attorney General

Warrantor: General Electric Company.Louisville, KY40225

GEAir Conditioner--One- YearLimitedWarranty. ForcustomersintheCanada

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care_ technician. For service, call

1.800.561.3344.Please have serial number and model number

available when calling for service.

Staple yourreceipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

Fromthedate Ofthe

originalpurchase

Mabe Will Replace:

Anypartof file air conditioner which fails due to a defect in materials or workmanship.

During this limitedone-yearwarranty,Mabe will also provide, free of charge, all labor and

related service to replace the defective part.

Service trips to your home to teach you how to

use the product.

Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner

is of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible

for providing adequate electrical connecting facilities.

Failure of the product resulting from modifications to

the product or due to unreasonable use including failure

to provide reasonable and necessary maintenance.

In commercial locations, labor necessary to move the

unit to a location where it is accessible for service

by an individual technician.

Replacement of house fuses or resetting of circuit

breakers.

Failure due to corrosion on models not corrosion-

protected.

Damage to the product caused by improper power supply

voltage, accident, fire, floods or acts of God.

Incidental or consequential damage caused by possible

defects with this air conditioner.

Damage caused after delivery.

EXCLUSION OFIMPLIED WARRANTIES--Your sole and exclusive remedy is product repair as provided in this

Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a

particular purpose, are limited to one year or the shortestperiod allowed by law.

This warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada

for home use within Canada. In-home warranty service will be provided in areas where it is available and deemed

reasonable by Mabe toprovide.

Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion

may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from

province toprovince. Toknow what your legal rights are in your province, consult your local or provincial consumer

affairs office.

Warrantor: Mabe Canada Inc.,

Burlington, Ontario

Consignes de s&_rit_ ............ 20, 21

Consignes d'utilisation ............. 22, 23

Entretien et nettoyage

Filtre _ air .......................... 23

Retrait du cadre de la grille ........... 23

Serpentins ext4rieurs ................. 23

Instructions de montage

Instructkms de montage pour une

installation a travers un mur--En option ...30

Instructions de montage

darts une fenOtre ................. 25-29

Conseils de d@annage .............. 33

Service & la clientOle

Service _ la clientele .................. 36

Garantie ............................ 35

Enregistrement du titre

de propri_t_ ..................... 31, 32

Inscrivezici les humerusdemodeleetde s&ie :

Numem demodele:

Numem deSerie :

Vous trouverez ces num&os sur l'_tiquette

appos_e sur le c6t_ du climadseur

Au Canada, visitez-nous au •

www.electromenagersge.ca

F F

/MPORTANTESCONS/GNESBESECUR/TE.

VEU/UEZt/RE TOUTESLESCONS/GNESAVANTUT/USAT/ON.

Pour votre s#curit#, les informafions contenues dans ce manuel doivent #tre suivies afin de minimiser

les risques d'incendie, de chocs filectriques ou de blessures corporefles.

CONSIGNESDESE-CUfllTE

}}N'utilisez cet appareil qu'aux fins pr&_ms }}

d_crites dans le mamml d'udlisadon.

iii}i}i

iii}i}}li_

Ce climatiseur dolt _tre correctement

install_ corffbrm_ment aux Instructions

d'Installadon infant toute udlisadon.

Ne d_branchezjamais votre climadseur en

drant sur le cordon d'a|imentadon. Prenez

toqjours refinement la fiche en main et drez

pour la sordr de la prise.

Remplacez imm&liamment tout cordon

_lectrique us_ ou endommag_. Un cordon

d'alimentadon endommag_ dolt atre

remplac_ par un nouveau cordon

d'alimentation obmnu &l fhbricant. Ne

r@arez pas le cordon endommagd. N'udlisez

pas un cordon fissur4 ou pr4sentant des

dommages &_saux ffottements soit sur

sa longueur ou aux extr_mit_s &l c6t_

de la fiche ou &l raccord.

iii}i}i

iii}i}}li_

Si la prise de courant est d'un tbrmat

dirt>rent de la fiche, cette prise dolt _tre

chang_e par un _lectricien qualifi_.

Eteignez votre climatiseur et d_branchez-le

m,'ant d'effecmer des r@aradons ou de

le nettoyer.

REMARQUE: Nousvousrecommandonsde faire

effectuer la maintenancepar un technicienqualifi_.

Pour votre sdcuritd, ne stockez pas et

n'udlisez pas de matdriaux combustibles,

d'essence ou d'autres vapeurs et liquides

inflammables dans les parages de cet

appareil ou de rout autre appareil.

Tousles climadseurs contiennent des fluides

fligorigbnes qui, corfformdment, itla

l_slation t_d&ale doivent Otre redr_s avant

la mise au rebut de l'appareil. Si vous mettez

au rebus un ancien appareil contenant des

fluides frigorigbnes, v&ifiez la procd&lre it

suivre aupras de la compagnie responsable

de l'41iminadon.

BRANCHEMENTSELECT.RIOUES

Ne coupez pas ou n'enlevez pas, sous aucun

pr#texte, la troisi#me broche de mise _ la terre

du cordon d'alimentafion. Pour des raisons

de s#curit#, cet appareil dolt gtre correctement

mis _ la terre.

N'utilisez PASd'adaptateur avec cet appareil.

Le cordon d'alimentadon de cet appareil

est _quip_ d'une fiche it trois broches (pour

une mise it la terre) qui s'adapm a la prise

de courant standard it 3 broches (pour une

mise itla terre) pour minimiser les risques

de chocs _lectriques par cet appareil.

Le cordon d'alimentadon est _quip_ d'un

dispositif d'intermpdon du courant. Un

bouton d'essai et de r_enclenchement est

fi)urni sur le boider de la prise. Vous devez

roster le mdcanisme rdguli_rement en

appuyant d'abord sur le bouton rest(Ess.i)

puis sur le bouton RESET(R_enclenchement)

lorsque l'appareil est branch,. Si le bouton

TEST(Ess.i)ne bascule pas ou si le bouton

RESET(Rdenclenchement) ne reste pas

enclenchd, cessez d'utiliser votre dimadseur

et appelez un technicien de ser_,ice qualifid.

Faites vdrifier la prise murale et le circuit

dlectrique par un dlectricien qualifid pour

s'assurer que le systbme est correctement

mis it la terre.

Dans le cas d'une prise biphasde,

l'installateur a la responsabilitd et l'obligadon

de la remplacer par une prise triphasde

correctement mise it la terre.

Le climatiseur dolt toujours _tre branchd

it sa propre prise dlectrique d'une mnsion

nominale correspondant it celle indiqude

sur sa plaque signalddque.

Ceci permet d'obtenir un meilleur rendement

du climafiseur et &ite de surcharger les circuits

dlectriques du domicile qui risque

d'occasionner un incendie en surchmNant.

Consultez les Consignes d'lnstallations, dans

la secdon Exigences Electriques pour les

exigences de branchements dlectriques

pardculiers.

La page charge ...

GE AEE08ASL1 Le manuel du propriétaire

Marque: GE

Modèle: AEE08ASL1

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: GE AEE08ASL1 Owner's manual
español: GE AEE08ASL1 El manual del propietario

GE AEE08ASL1 Le manuel du propriétaire

GE AEE08ASL1 Le manuel du propriétaire

dans d''autres langues

Documents connexes