Ebode HDSWITCH31 Manuel utilisateur

Catégorie
Séparateurs vidéo
Taper
Manuel utilisateur

Ce manuel convient également à

www.ebodeelectronics.eu
HD Mini Switchers
HDSWITCH31 HDSWITCH51
HDSWITCH31 User guide 2
HDSWITCH31 Bedienungsanleitung 6
HDSWITCH31 Gebruikershandleiding 10
HDSWITCH31 Guide utilisateur 14
HDSWITCH51 User guide 18
HDSWITCH51 Bedienungsanleitung 22
HDSWITCH51 Gebruikershandleiding 26
HDSWITCH51 Guide utilisateur 30
Before using our product, please read this document carefully.
24-5-2013 2 ebode HD Mini Switchers
User guide
Contents
1. CONFORMITY OF USE
2. INTRODUCTION
3. SPECIFICATIONS
4. SET CONTENTS
5. ADVANTAGES
6. PRODUCT OVERVIEW
7. APPLICATION
8. WARNING
1. Conformity of Use
For carefree and safe use of this product, please read this manual and safety information
carefully and follow the instructions. The unit is registered as a device that does not
cause or suffer from radio-frequency interference. It is CE approved and it conforms with
the Low Voltage Directory. The safety and installation instructions must be observed.
Technical manipulation of the product, or any changes to the product, are forbidden, due
to security and approval issues. Please take care to set up the device correctly - consult
your user guide. Young children should use the device only under adult supervision. No
guarantee or liability will be accepted for any damage caused due to incorrect use of the
equipment supplied, other than indicated in this owner’s manual.
Safety Warnings
To prevent short circuits, this product (except if specified for outdoor usage) should
only be used inside and only in dry spaces. Do not expose the components to rain or
humidity.
Only connect the power cord to the mains after checking whether the mains voltage
is the same as the values on the rating labels. Never connect a power cord when it is
damaged. In that case, contact your supplier. If there is any danger of a thunderstorm,
it is a good precaution to unplug the power supply from the mains network in order to
protect it from lightning. The same applies if the system is to be out of action for any
length of time.
Avoid strong mechanical tear and wear, extreme ambient temperatures, strong
vibrations and atmospheric humidity.
Do not disassemble any part of the product: the device contains live parts and no
user-serviceable parts are inside. The product should only be repaired or serviced by
qualified and authorized service personnel. Defected pieces must be replaced by original
(spare) parts.
In case of improper usage or if you have opened, altered and repaired the product
yourself, all guarantees expire. The supplier does not accept responsibility in the case of
improper usage of the product or when the product is used for purposes other than
specified. The supplier does not accept responsibility for additional damage other than
covered by the legal product responsibility.
24-5-2013 3 ebode HD Mini Switchers
2. Introduction
Thank you for purchasing the ebode HDSWITCH31. The HDMI switch, HDSWITCH31 has
a compact size and includes 3 x HDMI female inputs, 1x HDMI female receiver device
output (e.g. HDTV or home cinema set) and is HDCP 1.2 compliant. The HDSWITCH31
offers high speed Full HD 1080p, 3D support, Blu-ray 24fs/ xv-YCC support, deep colour
36bit and signal retiming. You can go up to 20m with an AWG24 HDMI input cable and
20m with an AWG24 HDMI output cable. Dolby-AC3/DTS7.1/DSD/DTS-HD/true-
HD/LPCM7.1 audio formats are supported. Select one of the three HDMI signal input
sources manually or with the included remote control. When switching your devices on
and off, it will automatically jump to the next available source. The source indicator on
the HDSWITCH31 shows the status of the in and output. Optional: HDIK30 IR over
HDMI accessories to remotely control A/V sources such as a DVD player.
3. Specifications
HDMI version: High speed with 3D / Ethernet
HDCP version: HDCP1.2
Support HDMI resolution: 1080p24fs/1080P/1080i/720P/576P/576i/480P/480i
Support video color bit: xv-YCC/deep color 24bit/36bit
Support audio format: Dolby-AC3/DTS7.1/DSD/DTS-HD/true-HD/LPCM7.1
Input video signal: 5.0Volts P-P
Output cable distance: ≤20m 24AWG Cable lenght
Input cable distance: ≤20m 24AWG Cable lenght
Data transfer speed: 6.75Gbps
Operating Humidity range: 5 to 90% RH (No Condensation)
Operating Temperature range: -15 to +55C˚
Power adapter format: Input AC (50Hz.60Hz) 100-240V, output 5v DC
Max working current: -300mA
Dimensions (LxWxH): 112x77.4x23.5mm
Weight: 219g
4. Set Contents
When unpacking your HDMI Splitter please check if the following items are included:
HDMI Switch
5V DC Power Supply
Remote control
User Manual
5. Advantages
3x HDMI input and 1x HDMI receiver device output
Switching control via remote or manually
Full-HD 1080P; 3D support, HDMI 1.4a
Compact size, smart and fast switching
Optional: HDMI IR control system, HDIK30
6. Operation
1. Connect your signal source such as DVD, PS3, STB to any available Input (figure 1.2).
2. Connect your display such as LCD, Plasma to the Output of the switch (figure 1.2).
3. Power the switch with the included power supply.
4. Connect the IR adapter kit, HDIK30 (not included) to the switch (figure 1.2).
24-5-2013 4 ebode HD Mini Switchers
7. Product overview
Figure 1.1
Figure 1.2
Note: Ebode HDIK30 - Receiver, Blaster and Adapter are optional items for this product
24-5-2013 5 ebode HD Mini Switchers
8. Warning
To reduce the risk of fire, electric shock or product damage:
1. Do not expose this apparatus to rain, moisture, dripping or splashing and make sure
that no objects filled with liquids, such as vases, are placed on the apparatus.
2. Do not install or place this unit in a bookcase, built-in cabinet or in another confined
space. Ensure the unit is well ventilated.
3. To prevent risk of electric shock or fire hazard due to overheating, do not obstruct the
unit’s ventilation openings with newspapers, tablecloths, curtains and similar items.
4. Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus.
5. Do not place sources of naked flames, such as lighted candles on the unit.
6. Clean this apparatus only with dry cloth.
7. Unplug this apparatus during lighting storms or when unused for long time.
8. Protect the power cord from being walked on or pinched, particularly at plugs.
9. Only use attachments/accessories specified by the manufacture.
10. Refer all servicing to qualified service personnel.
24-5-2013 6 ebode HD Mini Switchers
Bedienungsanleitung
Inhalt
1. KONFORMITÄTSBESTIMMUNGEN
2. EINLEITUNG
3. TECHNISCHE DATEN
4. LIEFERUMFANG
5. VORTEILE
6. INBETRIEBNAHME
7. PRODUKTÜBERSICHT
8. WARNUNG
1. Konformitätsbestimmungen
Für unbeschwerte und sichere Verwendung dieses Produktes lesen Sie bitte diese
Bedienungsanleitung und Sicherheitshinweise sorgfältig durch und folgen Sie den
Anweisungen. Das Gerät ist als ein Gerät registriert, das keine hochfrequente Störungen
aussendet und nicht von solchen beeinflusst wird. Es ist CE-geprüft und entspricht der
Niederspannungsrichtlinie. Die Sicherheits-und Installationsanweisungen sind zu beachten.
Technische Manipulationen des Produkts, oder Änderungen an dem Produkt sind aufgrund
von Sicherheits- und Zulassungsbestimmungen verboten. Bitte achten Sie darauf, das
Gerät korrekt einzurichten - konsultieren Sie die Bedienungsanleitung. Kleine Kinder sollten
das Gerät nur unter Aufsicht von Erwachsenen verwenden. Es wird keine Garantie oder
Haftung für Schäden übernommen, die durch falsche Verwendung des Gerätes entgegen
dieser Bedienungsanleitung entstanden sind.
Sicherheitshinweise
Um Kurzschlüsse zu vermeiden, sollte dieses Produkt (außer wenn es ausdrücklich für
den Außeneinsatz konzipiert ist) nur innerhalb und nur in trockenen Räumen verwendet
werden. Setzen Sie die Komponenten nicht Regen oder Feuchtigkeit aus.
Schließen Sie das Netzkabel erst dann an das Stromnetz an, wenn Sie überprüft haben,
ob die Netzspannung den gleichen Wert aufweist, wie auf dem Typenschild vermerkt.
Verbinden Sie niemals ein Netzkabel, wenn es beschädigt ist. In diesem Fall kontaktieren
Sie Ihren Lieferanten. Wenn ein Gewitter heranzieht, ist es eine gute Vorsichtsmaßnahme,
die Stromversorgung aus dem Netz ziehen, um das Gerät vor Blitzschlag zu schützen. Das
gleiche gilt, wenn Sie das System für längere Zeit außer Betrieb nehmen.
• Vermeiden Sie starke mechanische Abnutzung, extreme Umgebungstemperaturen, starke
Vibrationen und Luftfeuchtigkeit.
Zerlegen Sie nie irgendeinen Teil des Produkts: Das Gerät enthält stromführende Teile
und keine vom Anwender zu wartenden Teile im Inneren. Das Produkt sollte nur repariert
oder gewartet werden von qualifiziertem und autorisiertem Service-Personal. Defekte Teile
müssen durch Original-(Ersatz-) Teile ersetzt werden.
Bei unsachgemäßer Nutzung oder wenn Sie das Produkt geöffnet haben, verändert oder
das Produkt selber repariert haben, erlöschen sämtliche Garantieansprüche. Der Lieferant
übernimmt keine Verantwortung im Falle einer falschen Verwendung des Produkts oder
wenn das Produkt für andere Zwecke als angegeben verwendet wird. Der Lieferant
übernimmt keine Verantwortung für Folgeschäden als für die, die durch die gesetzliche
Produkthaftung gedeckt werden.
24-5-2013 7 ebode HD Mini Switchers
2. Einleitung
Vielen Dank, dass Sie sich für den ebode HDSWITCH31 entschieden haben. Der HDMI
Schalter HDSWITCH31 ist ideal für Fernsehgeräte, die nur über einen HDMI-Eingang
verfügen, jedoch mit mehreren Quellgeräten verbunden werden soll. Er besticht durch
seine kompakte Größe und ist HDCP 1.2 kompatibel. Der HDSWITCH31 beinhaltet drei
HDMI Eingangsbuchsen und einen HDMI Receiver für das Zielgerät (z.B. HDTV oder eine
Heimkinoanlage). Der HDSWITCH31 unterstützt High Speed Full HD Auflösungen bis
1080p, 3D-Wiedergabe, Blu-ray 24fs/ xv-YCC Wiedergabe, eine Farbtiefe von 36bit und
Signal-Retiming. Sie können ein 24AWG HDMI Kabel (Eingang) mit einer Länge von bis
zu 20m und ein 24AWG HDMI Kabel (Ausgang) mit Länge 20m verwenden. Unterstützte
Audioformate: Dolby-AC3/DTS7.1/DSD/DTS-HD/true-HD/LPCM7.1. Wählen Sie eine der
drei HDMI Eingangssignale entweder manuell oder mit der im Lieferumfang enthaltenen
Fernbedienung aus. Beim Ein- und/oder Ausschalten Ihrer Geräte wird automatisch die
nächste verfügbare Quelle gesucht. Eine Anzeige gibt Aufschluss über den Status der
Ein- und Ausgänge. Optionales: HDIK30 - IR über HDMI Zubehör vor Bedienung von A/V
Endgeräten (z.B. DVD-Playern).
3. Technische Daten
HDMI Version: High Speed mit 3D / Ethernet
HDCP Version: HDCP1.2
Unterstütze HDMI Auflösung: 1080p24fs/1080P/1080i/720P/576P/576i/480P/480i
Unterstützte Farbtiefe: xv-YCC/ 24bit/36bit-Farbtiefe
Unterstützte Audioformate: Dolby-AC3/DTS7.1/DSD/DTS-HD/true-HD/LPCM7.1
Input Video: 5,0Volts P-P
Kabellänge (Ausgang): ≤20m 24AWG
Kabellänge (Eingang): ≤20m 24AWG
Datenübertragungsrate: 6.75Gbps
Zulässige Luftfeuchtigkeit: 5 bis 90% RH (nicht kondensierend)
Betriebstemperaturbereich: -15 bis +55C˚
Netzteil: Eingang AC (50Hz.60Hz) 100-240V, Ausgang 5v DC
Strom-Aufnahme: -300mA
Abmessungen (LxBxH): 112x77.4x23.5mm
Gewicht: 219g
4. Lieferumfang
Folgende Produkte sind im Lieferumfang enthalten:
HDMI Schalter
5V DC Netzteil
Fernbedienung
Bedienungsanleitung
5. Vorteile
3x HDMI Input und 1x HDMI Receiver Output
Umschalten der Kanäle über eine Fernbedienung oder manuell am Gerät
Full-HD 1080P; 3D Wiedergabe, HDMI 1.4a
Kompakte Größe, schnelles und intelligentes Umschalten
Optional: HDMI IR Adapter Kit, HDIK30
6. Inbetriebnahme
1. Verbinden Sie Ihr Quellgerät (DVD-Player, PS3) mit der freien Buchse (Darstellung 1.2)
2. Verbinden Sie Ihren Bildschirm mit dem Ausgang des Schalters (Darstellung 1.2)
3. Verbinden Sie den Schalter mit dem mitgelieferten Netzteil
4. Verbinden Sie das IR Adapter Kit, HDIK30 (nicht im Lieferumfang) mit dem
HDSWITCH31. (Darstellung 1.2)
24-5-2013 8 ebode HD Mini Switchers
7. Produktübersicht
Darstellung 1.1
Darstellung 1.2
Anmerkung: Ebode HDIK30 - Receiver, Lautsprecher und Adapter sind optionales
Zubehör
24-5-2013 9 ebode HD Mini Switchers
8. Warnung
Um das Risiko von Feuer, elektrischem Stromschlag oder Produktschäden zu verringern,
beachten Sie bitte Folgendes:
1. Setzen Sie das Produkt weder Regen, Feuchtigkeit noch Nässe aus. Gehen Sie sicher,
dass keine mit Flüssigkeit gefüllten Gegenstände (wie Blumenvasen) in der Nähe von
dem Produkt stehen.
2. Wenn das Produkt auf einem Bücherregal platziert oder in einem Einbauschrank
eingebaut wird, stellen Sie sicher, dass es gut belüftet wird.
3. Um das Risiko von Stromschlägen oder Feuer durch Überhitzung zu verhindern, sorgen
Sie dafür, dass die Belüftungen nicht durch Zeitungen, Tischdecken oder ähnlichen
Materialien abgedeckt sind.
4. Installieren Sie das Produkt nicht in der Nähe von Wärmequellen wie Heizungen, Öfen
oder ähnlichen Apparaturen.
5. Stellen Sie keine brennenden Kerzen oder ähnliches auf das Gerät oder in die Nähe des
Geräts.
6. Reinigen Sie das Gerät nur mit trockenen Tüchern!
7. Trennen Sie das Gerät während eines Gewitters oder bei längerer Nichtbenutzung vom
Stromnetz.
8. Achten Sie darauf, dass das Stromkabel geschützt und nicht geknickt wird (besonders
am Stecker).
9. Verwenden Sie nur Zubehör, das auch vom Hersteller empfohlen wird.
10. Überlassen Sie jegliche Wartung qualifiziertem Personal.
24-5-2013 10 ebode HD Mini Switchers
Gebruikershandeiding
Inhoud
1. GEBRUIKSVOORSCHRIFT
2. INTRODUCTIE
3. SPECIFICATIES
4. INHOUD
5. VOORDELEN
6. WERKING
7. PRODUCTOVERZICHT
8. WAARSCHUWING
1. Gebruiksvoorschrift
Voor een zorgeloos en veilig gebruik van dit product, dient u deze handleiding en
veiligheidsinformatie zorgvuldig te lezen en de instructies op te volgen. Het apparaat is
geregistreerd als een apparaat dat geen verstoring door radiofrequentie veroorzaakt of hier
hinder van ondervindt. Het is CE goedgekeurd en voldoet aan de laagspanningsrichtlijn. De
veiligheid en installatie-instructies dienen in acht te worden genomen. Technische
veranderingen van het product, dan wel wijzigingen aan het product, zijn verboden, om
redenen van veiligheid en keuringen. Let er op bij gebruik van het apparaat dat u de
gebruikershandleiding correct raadpleegt. Jonge kinderen mogen het apparaat alleen onder
toezicht van volwassenen gebruiken. Garantie of aansprakelijkheid zullen niet worden
aanvaard voor schade veroorzaakt door verkeerd gebruik van de geleverde apparatuur,
anders dan vermeld in deze handleiding.
Veiligheidswaarschuwingen
Om kortsluiting te voorkomen, dient dit product (tenzij anders aangegeven voor gebruik
buitenshuis) alleen binnen en alleen te worden gebruikt in droge ruimten. Stel de
componenten niet bloot aan regen of vocht.
Sluit de stroomkabel aan op het stopcontact nadat u hebt gecontroleerd of de
netspanning gelijk is aan de waarde die op de typeplaatjes is aangegeven. Sluit nooit een
stroomkabel aan wanneer deze beschadigd is. In dat geval kunt u contact opnemen met
uw leverancier. Als er gevaar dreigt van onweer, is het een goede voorzorgsmaatregel om
de voeding los te koppelen van het elektriciteitsnet, om het te beschermen tegen bliksem.
Hetzelfde geldt als het systeem voor enige tijd buiten werking gesteld is.
Vermijd sterke mechanische slijtage, extreme temperaturen, sterke trillingen en
luchtvochtigheid.
Demonteer geen delen van het product: de apparatuur bevat onder spanning staande
delen en bevat geen, door de gebruiker te repareren, onderdelen. Het product mag alleen
worden gerepareerd of onderhouden door gekwalificeerd en bevoegd personeel. Defecte
onderdelen moeten worden vervangen door originele (reserve) onderdelen.
In het geval van onjuist gebruik of wanneer u het product zelf hebt geopend, gewijzigd of
reparaties hebt aangebracht, komen alle garantiebepalingen te vervallen. De leverancier
aanvaardt geen enkele aansprakelijkheid in het geval van onjuist gebruik van het product
of wanneer het product wordt gebruik voor andere doeleinden dan aangegeven. De
leverancier aanvaardt geen enkele aansprakelijkheid voor schade anders dan de wettelijke
aansprakelijkheid.
24-5-2013 11 ebode HD Mini Switchers
2. Introductie
Bedankt voor de aankoop van de ebode HDSWITCH31. De HDSWITCH31 heeft een
compact formaat en bevat 3x HDMI female ingang, 1x HDMI female ontvanger uitgang
(bijv. HDTV of home cinema set) en is HDCP verenigbaar. De HDSWITCH31 biedt u super
snel Full HD 1080p, 3D ondersteuning, Blu-ray 24fs / xv-YCC ondersteuning, deep colour
36 bit en signaal retiming. U heeft een bereik van tot 20m met zowel de AWG24 ingang
kabel als met de AWG24 HDMI uitgang kabel. Dolby-AC3/DTS7.1/DSD/DTS-HD/true-
HD/LPCM7.1 audio formaten worden ondersteund. Selecteer een van de drie HDMI-signaal
ingang bronnen handmatig of met de meegeleverde afstandsbediening. Bij het in- en
uitschakelen van uw apparaat, zal het de HDSWITCH31 automatisch naar de volgende
beschikbare bron schakelen. De bronindicator op de HDSWITCH31 toont de status van de
in- en uitgang. Optioneel: HDIK30 - IR over HDMI accessoires om externe A/V bronnen te
bedienen, zoals een DVD speler.
3. Specificaties
HDMI versie: High speed met 3D / ethernet
HDCP versie: HDCP1.2
Ondersteuning HDMI resolutie: 1080p24fs/1080P/1080i/720P/576P/576i/480P/480i
Ondersteuning video bit kleur: xv-YCC/deep colour 24bit/36bit
Ondersteuning audio formaat: Dolby-AC3/DTS7.1/DSD/DTS-HD/true-
HD/LPCM7.1Ingang video signaal: 5.0Volts P-P
Uitgang kabelafstand: ≤20m 24AWG kabel
Ingang kabelafstand: ≤20m 24AWG kabel
Data transfer snelheid: 6.75Gbps
Actief luchtvochtigheidsbereik: 5 to 90% RH (Geen condensatie)
Actief temperatuurbereik: -15 to +55C˚
Formaat voedingsadapter: Ingang AC (50Hz.60Hz) 100-240V, uitgang 5v DC
Max. lopende werking: -300mA
Afmetingen (LxBxH): 112x77.4x23.5mm
Gewicht: 219g
4. Inhoud
Controleert u bij het uitpakken van uw HDSWITCH31 of de volgende items zijn
meegeleverd:
HDMI Switch
5V DC Voeding
Afstandsbediening
Gebruikershandleiding
5. Voordelen
3x HDMI ingang en 1x HDMI ontvanger uitgang
Bediening via afstandsbediening of handmatig
Full-HD 1080P; 3D ondersteuning, HDMI 1.4a
Compacte afmeting, slim en snel schakelen
Optioneel: HDMI IR controle system, HDIK30
6. Werking
1. Sluit uw signaalbron (DVD, PS3, STB) aan op een beschikbare ingang (figuur 1.2).
2. Verbind het beeldscherm (LCD, Plasma) met de uitgang van de schakelaar (figuur 1.2).
3. Verbind de switch met de bijgeleverde voeding.
4. Sluit de IR adapter kit, HDIK30 (niet inclusief) aan op de switch (figuur 1.2).
24-5-2013 12 ebode HD Mini Switchers
7. Productoverzicht
Figuur 1.1
Figuur 1.2
Opmerking: Ebode HDIK30 - Ontvanger, blaster en adapter zijn optionele items voor dit
product.
24-5-2013 13 ebode HD Mini Switchers
8. Waarschuwing
Om het risico van brand, elektrische schokken of schade aan het product te beperken:
1. Stel het apparaat niet bloot aan regen, vocht, druppels of spatten en zorg er voor dat
er geen met vloeistof gevulde voorwerpen, zoals vazen op het apparaat worden
geplaatst.
2. Indien geïnstalleerd of geplaatst in een boekenkast, inbouwkast of een andere
afgesloten ruimte, zorg er voor dat het apparaat goed geventileerd is.
3. Om het risico van elektrische schokken of brandgevaar door oververhitting te
voorkomen, zorg er voor dat de ventilatieopeningen niet bedekt zijn met kranten,
tafelkleden, gordijnen en dergelijke.
4. Plaats het apparaat niet in de buurt van warmtebronnen zoals radiatoren, warmte
uitlaten, kachels of andere apparaten.
5. Plaats geen open vuur bronnen, zoals brandende kaarsen op het apparaat.
6. Reinig het apparaat uitsluitend met een droge doek.
7. Koppel het apparaat los bij onweer en bliksem of wanneer het apparaat voor langere
tijd niet wordt gebruikt.
8. Bescherm het netsnoer zodat er niet overheen gelopen kan worden, vooral bij stekkers.
9. Gebruik uitsluitend hulpstukken/accessoires die door de fabrikant worden
gespecificeerd.
10. Laat al het onderhoud over aan gespecificeerd personeel.
24-5-2013 14 ebode HD Mini Switchers
Guide utilisateur
Contents
1. CONFORMITÉ D’UTILISATION
2. INTRODUCTION
3. CARACTERISTIQUES
4. CONTENU
5. AVANTAGES
6. FONCTIONNEMENT
7. APERÇU PRODUIT
8. ATTENTION
1. Conformité d’utilisation
Pour une utilisation correcte et sans danger de ce produit, veuillez lire attentivement ce
manuel et suivre ses instructions. Ce produit est conforme aux normes en vigueur et au
marquage CE. Toute manipulation technique du produit ou tout changement du produit
sont interdits en raison des normes de sécurité et de conformité. Veuillez installer
correctement le produit - pour ce faire, consultez le guide d’utilisation. Ne pas laisser les
enfants utiliser ce produit sans la surveillance d’un adulte. Aucune garantie ou
responsabilité ne sera accepen cas d'usage incorrect de l'équipement ou différent de
celui expliqué dans ce guide utilisateur.
Preacautions de securite
Pour éviter tous risques de court circuit, ce produit doit être utilisé à l'intérieur
uniquement. Evitez de l'utiliser dans des locaux très humides. N'exposez pas les produits
à la pluie ou à l'humidité.
Branchez le cordon d'alimentation sur le secteur uniquement après avoir vérifié que
la tension du réseau correspond à la valeur indiquée sur les étiquettes de notation. Ne
jamais brancher le cordon d'alimentation s'il est endommagé. Dans ce cas, contactez
votre fournisseur. S'il y a danger d'orage, il est conseillé de débrancher l'alimentation
électrique afin de le protéger de la foudre. Ceci s'applique également si le système est
inutilisé pendant une longue période.
Evitez les contraintes mécaniques, les températures extrêmes, les chocs, les
vibrations ainsi que les atmosphères humides.
Ne démontez aucun élément du kit de transmission. Aucun composant du kit ne peut
faire l’objet d’une réparation par l’utilisateur. Si vous versez du liquide sur le récepteur,
débranchez-le du secteur, afin d’éviter tout risque d’électrocution ou d’incendie, et
consultez un technicien qualifié. Les pièces défectueuses doivent être remplacées par
des pièces d’origine.
Dans le cas d'un usage impropre ou si vous avez ouvert, modifié et réparé le produit
vous-même annule la garantie. Le fournisseur n'assume aucune responsabilité en cas
d'utilisation impropre du produit ou si le produit est utilisé à des fins autres que celles
spécifiées. Le fournisseur n'assume aucune responsabilité pour dommage conséquent,
autre que la responsabilité civile du fait des produits.
24-5-2013 15 ebode HD Mini Switchers
2. Introduction
Nous vous remercions d’avoir acheté le HDSWITCH31 de Ebode. Le commutateur HDMI,
HDSWITCH31 a une taille compacte et comprend 3 entrées femelle HDMI et 1 sortie
HDMI (pour TV HD ou home cinéma par exemple) et est compatible HDCP 1.2. Le
HDSWITCH31 offre un haut débit Full HD 1080p, supporte la 3D, Blu-ray 24FS/xv YCC-,
les couleurs profondes 36bits et la resynchronisation du signal. Vous pouvez atteindre
20m avec un câble d’entrée HDMI AWG24 et 20m avec un câble de sortie HDMI AWG24.
Formats audio supportées: Dolby-AC3/DTS7.1/DSD/DTS-HD/true-HD/LPCM7.1. Vous
pouvez sélectionner l'une des trois sources d'entrée de signal HDMI manuellement ou
avec la télécommande fournie. Lorsque vous allumez et éteignez un appareil, la
prochaine source disponible est automatiquement selectionnée. L'indicateur de source
du HDSWITCH31 montre l'état des entrées et sorties. En option: HDIK30 - Accessoire IR
vers HDMI, pour contrôler les sources distantes A/V comme un lecteur DVD.
3. Caractéristiques
Version HDMI: Haute vitesse avec 3D / ethernet
Version HDCP: HDCP1.2
Résolution HDMI Supportée: 1080p24fs/1080P/1080i/720P
/576P/576i/480P/480i
Couleur supportée: xv-YCC/deep color 24bit/36bit
Format audio supporté: Dolby-AC3/DTS7.1/DSD/DTS-HD/true-HD/LPCM7.1
Signal d’ente vidéo: 5.0Volts P-P
Distance cable sortie: ≤20m 24AWG Longueur Câble
Distance cable entrée: ≤20m 24AWG Longueur Câble
Vitesse transfert de données: 6.75Gbps
Plage d’humidité: 5 to 90% RH (Sans Condensation)
Plage de température: -15 to +55C˚
Alimentation: Entré AC (50Hz.60Hz) 100-240V, sortie 5v DC
Courant Max supporté: -300mA
Dimensions (LxWxH): 112x77.4x23.5mm
Poid: 219g
4. Contenu
Lorsque vous ouvrez le paquet, merci de vérifier que tous ces éléments sont inclus:
Commutateur HDMI
Alimentation 5V DC
Télécommande
Manuel utilisateur
5. Avantages
3x entrées HDMI et 1x sortie HDMI
Contrôle manuel ou via la télécommande
Full-HD 1080P; support de la 3D, HDMI 1.4a
Taille compacte, fin et changement de source rapide
Option: Système de contrôle HDMI IR, HDIK30
6. Fonctionnement
1. Connectez votre source DVD, PS3, STB à une entrée disponible (figure 1.2).
2. Connectez votre écran LCD, Plasma à la sortie du commutateur (figure 1.2).
3. Alimentez le commutateur avec l’alimentation fournie.
4. Connectez le module IR, HDIK30 (non inclus) au commutateur (figure 1.2).
24-5-2013 16 ebode HD Mini Switchers
7. Aperçu produit
Image 1.1
Image 1.2
Note: Ebode HDIK30 - Récepteur et adaptateur sont vendus séparément pour ce produit.
24-5-2013 17 ebode HD Mini Switchers
8. Attention
Pour réduire les risques d’incendie, de choc électrique ou dommages sur le produit:
1. Ne pas exposer le produit à la pluie, moisissures, éclaboussures et assurez-vous
qu’auncun objet contenant du liquide, comme un vase, ne se trouve sur l’appareil.
2. Si installé ou placé dans une bibliothèque, un meuble encastré ou n’importe quel
environnement confiné, soyez sûr que le produit est bien ventilé.
3. Pour prévenir des dangers électriques ou incendiaires dus à un sur échauffement, ne
pas boucher la sortie de ventilation du produit avec des journaux, une nappe, des
rideaux ou tout objet de ce genre.
4. Ne pas installer près d’une source de chaleur comme un radiateur, une cheminée, un
poêle ou tout objet de ce genre.
5. Ne pas placer de flamme nue, comme des bougies, sur l’appareil.
6. Nettoyez cet appareil avec un chiffon sec.
7. Débranchez l’appareil pendant un orage ou pour une longue période de non-utilisation.
8. Protégez le cordon afin d’éviter qu’il ne soit piétiné ou pincé, en particulier au niveau
des fiches.
9. N’utiliser que des fixations/accessoires spécifiés par le fabricant.
10. Confiez toutes les réparations à un personnel qualifié.
24-5-2013 18 ebode HD Mini Switchers
User guide
Contents
1. CONFORMITY OF USE
2. INTRODUCTION
3. SPECIFICATIONS
4. SET CONTENTS
5. ADVANTAGES
6. OPERATION
7. APPLICATION
8. WARNING
1. Conformity of Use
For carefree and safe use of this product, please read this manual and safety information
carefully and follow the instructions. The unit is registered as a device that does not
cause or suffer from radio-frequency interference. It is CE approved and it conforms with
the Low Voltage Directory. The safety and installation instructions must be observed.
Technical manipulation of the product, or any changes to the product, are forbidden, due
to security and approval issues. Please take care to set up the device correctly - consult
your user guide. Young children should use the device only under adult supervision. No
guarantee or liability will be accepted for any damage caused due to incorrect use of the
equipment supplied, other than indicated in this owner’s manual.
Safety Warnings
To prevent short circuits, this product (except if specified for outdoor usage) should
only be used inside and only in dry spaces. Do not expose the components to rain or
humidity.
Only connect the power cord to the mains after checking whether the mains voltage
is the same as the values on the rating labels. Never connect a power cord when it is
damaged. In that case, contact your supplier. If there is any danger of a thunderstorm,
it is a good precaution to unplug the power supply from the mains network in order to
protect it from lightning. The same applies if the system is to be out of action for any
length of time.
Avoid strong mechanical tear and wear, extreme ambient temperatures, strong
vibrations and atmospheric humidity.
Do not disassemble any part of the product: the device contains live parts and no
user-serviceable parts are inside. The product should only be repaired or serviced by
qualified and authorized service personnel. Defected pieces must be replaced by original
(spare) parts.
In case of improper usage or if you have opened, altered and repaired the product
yourself, all guarantees expire. The supplier does not accept responsibility in the case of
improper usage of the product or when the product is used for purposes other than
specified. The supplier does not accept responsibility for additional damage other than
covered by the legal product responsibility.
24-5-2013 19 ebode HD Mini Switchers
2. Introduction
Thank you for purchasing the ebode HDSWITCH51. The HDMI switch, HDSWITCH51 has
a compact size with 5 x HDMI female inputs, 1x HDMI female output to HDMI receiver
device (like HDTV) and is HDCP 1.2 compliant. With the HDSWITCH51 you can connect 5
HDMI devices to your TV or home cinema set. The HDSWITCH51 offers high speed Full
HD 1080p, 3D support, Blu-ray 24fs/ xv-YCC support, deep colour 36bit and signal
retiming. You can go up to 20m with an AWG24 HDMI input cable and 20m with an
AWG24 HDMI output cable. Dolby-AC3/DTS7.1/DSD/DTS-HD/true-HD/LPCM7.1 audio
formats are supported. Select one of the five HDMI signal input sources, manually or
with the included remote control. When switching your devices on and off, it will
automatically jump to the next available source. The source indicator on the
HDSWITCH51 shows the status of the in and output. Optional: HDIK30 IR over HDMI
accessories to remotely control A/V sources such as a DVD player.
3. Specifications
HDMI version: High speed with 3D / Ethernet 1.4a
HDCP version: HDCP1.2
Support HDMI resolution: 1080p24fs/1080P/1080i/720P/576P/576i/480P/480i
Support video colour bit: xv-YCC/deep colour 24bit/36bit
Support audio format: Dolby-AC3/DTS7.1/DSD/DTS-HD/true-HD/LPCM7.1
Input video signal: 5.0Volts P-P
Output cable distance: ≤20m 24AWG Cable length
Input cable distance: ≤20m 24AWG Cable length
Data transfer speed: 6.75Gbps
Operating Humidity range: 5 to 90% RH (No Condensation)
Operating Temperature range: -15 to +55C˚
Power adapter format: Input AC (50Hz.60Hz) 100-240V, output 5v DC
Max working current: -300mA
Dimensions (LxWxH): 112x77.4x23.5mm
Weight: 219g
4. Set Contents
When unpacking your HDMI Splitter please check to see if the following items are included:
HDMI Switch
5V DC 1.2 A Power Supply
Remote control
User Manual
5. Advantages
5x different HDMI input and 1x HDMI display sink
Switching control via remote or manually
Full-HD 1080P;3D support, HDMI 1.4a
Compact size, smart and fast switching
Optional IR control system, HDIK30
6. Operation
1. Connect your signal source such as DVD, PS3, STB to any available Input (figure 1.2).
2. Connect your display such as LCD, Plasma to the Output of the switch (figure 1.2).
3. Power the switch with the included power supply.
4. Connect the IR adapter kit, HDIK30 (not included) to the switch (figure 1.2).
24-5-2013 20 ebode HD Mini Switchers
7. Application
Figure 1.1
Figure 1.2
Note: Ebode HDIK30 - Receiver, Blaster and Adapter are optional items for this product
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Ebode HDSWITCH31 Manuel utilisateur

Catégorie
Séparateurs vidéo
Taper
Manuel utilisateur
Ce manuel convient également à