GEAppliances.com
SmartDispense Detergent Dispenser
Water Hardness Calibration
Prior to the first use, the dishwasher needs
to be calibrated for water hardness. Pleasefollow
the directions below to calibrate the dishwasher
to the hardness of gour tap water.
Determine the Hardness of Your Tap Water
In the bag that contained these instructions, gou
should find a water hardness test strip package.
Readthe instructions on the package, remove the
test strip and follow the instructions to determine
the hardness level of gour tap water. You will use
this information to calibrate gour dishwasher to
dispense the optimal amount of detergent.
Water hardness test strip indication. Valueto Enter
into Dishwasher
SO FT
OREDII I I I I I I I 1
1 RED _ 2
2 RED _ 3
3 RED _ 4
HARD 4 RED _ 5
1-31Pressthe "Up" A arrow pad to raisethe value
or the "Down" v arrow pad to lower the value.
Setthe water hardnessvalue to the number
determined with the test strip and table at the left.
1-4-IOncethe water hardness isset, pressthe
START/RESETpad to save the setting and return
the dishwasher to normal operation.
Calibration of Models Without a 3-Digit Display
Front controls
[]
Calibration of 12-Button Front-Control _1
Models With 3-Digit Displag
Pressatthesametime. Display
I--A'I
m Closeand latch the door (lightson,dishwasher Ibl
i-,-i
not running).
_] Pressthe SANIWASH/ANTI-BACTERIALandDELAY
HOURSpadsat the sametime for 3 seconds. Top
Thedisplagwill show a numberfrom I.to 5.This FI
isthe water hardnessvalue currentlg set.
E] PresstheSANI WASH/ANTI-BACTERIALpad to 141
raisethe value or the NORMALpad to lower
the value. Setthe water hardnessvalue to the
number determined with the test strip and table
above.
@
@
Oncethe water hardness isset, pressthe
START/RESETpad to savethe setting and return
the dishwasherto normal operation.
Calibration of 7-Button Top-Control Models _1
With 3-Digit Displag
Closeand latch the door (lightson,dishwasher
not running).
PresstheSANIWASH/ANTI-BACTERIALand DELAY
HOURSpads atthe sametime for 3seconds.All
lights will light up and gou will hear I to 5 beeps.
Thenumber of beeps indicatesthe current
hardness value.
............ P_¢ .................... -- m m m j,,,-,,_,_....
TT
Display Pressatthesametime.
FI"] Open the door and touch a pad (otherthan
STAR#to turn lights on.
_] Pressthe "Up" A arrow pad and DELAYHOURS
pad at the same time for 3 seconds.The display
will show a number from 1 to 5.Thisisthe water
hardnessvalue currently set.
Tochange the setting,press the DELAYHOURS
pad the number of times that correspondsto the
water hardnessvalue determined at the left. The
control will beep each time you pressthe pad.
Oncefinished pressingthe pad,gou will hear a
confirmation with beepsfor the number of times
gou pressedthe pad.
Ifthe number of beepsisnot what gou desire,
start pressingthe DELAYHOURSpad again to
reenter a new water hardness level.
Oncethe water hardness isset, pressthe
START/RESETpad to save the setting and return
the dishwasher to normal operation.
controls
Open the door and touch a pad to turn lights on.
Pressthe "Up" A arrow pad and DELAYHOURS
pad at the same time for 5 seconds.All lights
will light up and gou will hear I to 5 beeps.The
number of beeps indicatesthe current hardness
value.
Tochange the setting,press the DELAYHOURS
pad the number of times that correspondsto the
water hardnessvalue determined at the left. The
control will beep each time you pressthe pad.
Oncefinished pressingthe pad,gou will hear a
confirmation with beepsfor the number of times
gou pressedthe pad.
r_lf the number of beepsisnot what you desire,
start pressingthe DELAYHOURSpad again to
reenter a new water hardness level.
FI Oncethe water hardness isset, pressthe
START/RESETpad to save the setting and return
the dishwasher to normal operation.
NOTE:Youshould recalibrate the dishwasher control
if water conditions change;for example, ifa water
softener sgstem isadded or removed from gour
home. 13