Whirlpool CHW9160GW Mode d'emploi
- Catégorie
- Machines à laver
- Taper
- Mode d'emploi
Ce manuel convient également à
INSTALLATION INSTRUCTIONS
COMMERCIAL FRONT-LOAD WASHER
INSTRUCTIONS D’INSTALLATION
LAVEUSE COMMERCIALE À CHARGEMENT FRONTAL
Table of Contents/Table des matières . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
W10918732B
www.whirlpoolcommerciallaundry.com
Coin Operated Model
Modèle payant
Non-Coin Operated Model
Modèle non payant
2
TABLE OF CONTENTS
WASHER SAFETY ................................................................................... 3
INSTALLATION REQUIREMENTS ..........................................................4
Tools and Parts .....................................................................................4
Accessories .......................................................................................... 4
Options .................................................................................................4
Location Requirements ........................................................................5
Drain System ........................................................................................ 5
Electrical Requirements........................................................................6
INSTALLATION INSTRUCTIONS ............................................................6
Remove Transport System ................................................................... 6
Connect the Inlet Hoses .......................................................................7
Connect the Drain Hose ....................................................................... 8
Secure the Drain Hose .........................................................................8
Level the Washer .................................................................................. 9
Complete Installation............................................................................9
USER & SET-UP INSTRUCTIONS ........................................................ 10
General User Information ...................................................................10
Control Set-Up Procedures ................................................................10
Start Operating Setup ........................................................................11
WASHER CARE .....................................................................................14
Cleaning Your Washer ........................................................................ 14
Water Inlet Hoses ............................................................................... 14
ASSISTANCE OR SERVICE .................................................................. 14
WARRANTY ........................................................................................... 15
TABLE DES MATIÈRES
SÉCURITÉ DE LA LAVEUSE ................................................................16
EXIGENCES D’INSTALLATION ............................................................17
Outillage et pièces ..............................................................................17
Accessoires ........................................................................................17
Options ...............................................................................................18
Exigences d’emplacement ................................................................. 18
Système de vidange ...........................................................................19
Spécifications électriques ..................................................................19
INSTRUCTIONS D’INSTALLATION ...................................................... 20
Dépose du système de transport ....................................................... 20
Raccordement des tuyaux d’alimentation..........................................21
Raccordement du tuyau de vidange ..................................................22
Immobilisation du tuyau de vidange ..................................................22
Réglage de l’aplomb de la laveuse ....................................................23
Achever l’installation ..........................................................................23
INSTRUCTIONS D’UTILISATION ET D’INSTALLATION .....................24
Informations générales ....................................................................... 24
Procédures de réglage des systèmes de commande ........................ 24
Paramétrage pour mise en marche .................................................... 25
ENTRETIEN DE LA LAVEUSE ..............................................................29
Nettoyage de la laveuse .................................................................... 29
Tuyaux d’arrivée d’eau .......................................................................30
ASSISTANCE OU SERVICE .................................................................. 30
GARANTIE ............................................................................................. 32
3
WASHER SAFETY
4
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free number
in “Accessories.”
If you have You will need to buy
Laundry tub or standpipe
taller than 96" (2.4 m)
Sump pump system (if not already
available)
Overhead sewer Standard 20 gal. (76 L), 30"
(762 mm) tall drain tub or utility sink
and sump pump (available from
local plumbing suppliers)
Floor drain Siphon break, Part Number 285834;
additional drain hose,
Part Number 8318155; and
connector kit, Part Number 285835
Drain hose too short 4 ft (1.2 m) drain hose extension kit,
Part Number 285863
Water faucets beyond
reach of fill hoses
2 longer water fill hoses:
6 ft (1.8 m), Part Number 76314
10 ft (3.0 m), Part Number 350008
Accessories
Enhance your washer with these premium accessories.
For more high-quality items or to order, call 1-866-698-2538,
or visit us at www.whirlpool.com/accessories. In Canada call:
1-800-688-2002 or visit us at www.whirlpoolparts.ca.
Part Number Accessory
8212526
Washer drip trays, fits under all
31682
All-purpose appliance cleaner
1903WH
Laundry supply storage cart
Options
Pedestal
You have the option of purchasing pedestals separately for this
washer. The pedestal will add to the total height of the washer.
Optional pedestal
Pedestal
Height
Approximate
Height with
Washer
Color
Part Number
2
7
⁄8" (73 mm)
47½" (1207 mm)*
White WHP0400VW
*Add 5/8" (16 mm) minimum for leveling feet.
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
The parts supplied are in the washer drum.
Tools needed for connecting the water inlet hoses:
■ Pliers (that open to
1
9
⁄16" [39.5 mm])
■ Flashlight (optional)
Tools needed for installation:
■ Open-end wrenches
1/2" and 9/16"
■ TORX
®
T20
®†
security
screwdriver
■ 1/4" nut driver
■ Level
■ Wood block
■ Ruler or measuring tape
A. U-shaped hose form
B. Water inlet hoses (2)
C. Inlet hose washers (4)
D. Transit bolt hole plug (4)
E. Beaded tie strap
A B
C
E
D
Parts supplied:
†®TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.
5
Washer Dimensions
A floor drain should be provided under the bulkhead. Prefabricated
bulkheads with electrical outlets, water inlet lines, and drain facilities
should be used only where local codes permit.
Drain System
The washer can be installed using the standpipe drain system
(floor or wall), the laundry tub drain system, or the floor drain
system. Select the drain hose installation method you need.
See “Tools and Parts.”
Standpipe drain system – wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe
of 2" (50 mm). The minimum carry-away capacity can be no
less than 12 gal. (45.5 L) per minute, per washer.
The top of the standpipe must be at least 30" (762 mm) high
and no higher than 96" (2.4 m) from the bottom of the washer.
30" min.
(762 mm)
A B
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter or in a
basement, laundry room, or recessed area. See “Drain System.”
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need:
■ A water heater set to deliver 120°F (49°C) water to the
washer.
■ A grounded electrical outlet located within 6 ft (1.8 m) of
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
■ Hot and cold water taps located within 4 ft (1.2 m) of the hot
and cold water fill valves, and water pressure of 20–100 psi
(137.9–689.6 kPa).
■ A level floor with a maximum slope of 1" (25 mm) under
entire washer. Installing the washer on soft floor surfaces,
such as carpets or surfaces with foam backing, is not
recommended.
■ A sturdy and solid floor to support the washer with a total
weight (water and load) of 400 lbs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage
in low temperatures.
Installation clearances
■ The location must be large enough to allow the washer
door to be fully opened.
■ Additional spacing should be considered for ease of
installation and servicing. The door opens more than
90° and is not reversible.
■ Additional clearances might be required for wall, door,
and floor moldings.
■ Additional spacing of 1" (25 mm) on all sides of the washer
is recommended to reduce noise transfer.
■ Companion appliance spacing should also be considered.
Recessed area installation
This washer may be installed in a recessed area. The installation
dimensions shown are the minimum spaces allowable. Additional
spacing should be considered for ease of installation and
servicing. See the chart below.
Installation clearances
(Use recommended clearance for easier installation.)
Recommended/Minimum
Back/Top Sides
Recessed/Undercounter 0"/0"
(0 mm)/(0 mm)
1"/0"
(25 mm)/(0 mm)
*Height without leveling feet installed
Door is not reversible
28
13
/16"
(732 mm)
44
5
/8"
(1134 mm)
27"
(686 mm)
50 ½"
(1282 mm)
37
13
/
16
"
(961 mm)
*
*
NOTE: The door is not reversible.
6
Shipping bolt with plastic spacer
INSTALLATION
INSTRUCTIONS
Remove Transport System
IMPORTANT: Position the washer so that the rear of the washer
is within approximately 3 ft (900 mm) of its final location.
There are 4 shipping bolts in the rear panel of the washer that
support the suspension system during transportation. These bolts
also retain the power cord inside the washer until the bolts are
removed.
1. Keep the washer in the upright position while removing the
shipping bolts.
Shipping bolt
Shipping bolt
Back view
Laundry tub drain system
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 30" (762 mm) above the floor.
Floor drain system
The floor drain system requires a siphon break that may be
purchased separately. See “Tools and Parts.”
The siphon break must be a minimum of 28" (710 mm) from
the bottom of the washer. Additional hoses might be needed.
Electrical Requirements
■ A 120-volt, 60 Hz., AC-only, 15- or 20-amp, fused electrical
supply is required. A time-delay fuse or circuit breaker is
recommended. It is recommended that a separate circuit
serving only this washer be provided.
■ This washer is equipped with a power supply cord having
a 3 prong grounding plug.
■ To minimize possible shock hazard, the cord must be
plugged into a mating, 3 prong, grounding-type outlet,
grounded in accordance with local codes and ordinances.
If a mating outlet is not available, it is the personal
responsibility and obligation of the customer to have the
properly grounded outlet installed by a qualified electrician.
■ If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that
the ground path is adequate.
■ Do not ground to a gas pipe.
■ Check with a qualified electrician if you are not sure
the washer is properly grounded.
■ Do not have a fuse in the neutral or ground circuit.
28" min.
(710 mm)
30" min.
(762 mm)
7
2. Using a ½" wrench, loosen each of the bolts.
3. Once the bolt is loose, move it to the center of the hole
and completely pull out the bolt, including the plastic
spacer covering the bolt.
4. Once all 4 bolts are removed, discard the bolts and spacers.
Push the power cord plug into the opening on the right side
of the rear panel and pull the power cord through the opening
on the left side of the rear panel; then close holes with the
attached cap. Do not pull plug end of power cord through
the right side hole.
5. Close the bolt holes with the 4 transport bolt hole plugs.
NOTE: If the washer is to be transported at a later date, call your
product distributor or installer. To avoid suspension and structural
damage, your washer must be properly set up for relocation
by a trained professional.
Connect the Inlet Hoses
Insert new flat washers (supplied) into each end of the inlet
hoses. Firmly seat the washers in the couplings.
A B
A. Coupling
B. Washer
Connect the inlet hoses to water faucets
Make sure the washer drum is empty.
1. Attach a hose to the hot water faucet. Screw on coupling
by hand until it is seated on the washer.
2. Attach a hose to the cold water faucet. Screw on coupling
by hand until it is seated on the washer.
3. Using pliers, tighten the couplings with an additional
two-thirds turn.
NOTE: Do not overtighten or use tape or sealants on the valve.
Damage to the valves can result.
Clear water lines
■ Run water through both faucets and inlet hoses, into
a laundry tub, drainpipe, or bucket, to get rid of particles
in the water lines that might clog the inlet valve screens.
■ Check the temperature of the water to make sure that the
hot water hose is connected to the hot water faucet and that
the cold water hose is connected to the cold water faucet.
Connect the inlet hoses to the washer
C. Cold water inlet
H. Hot water inlet
1. Attach the hot water hose to the check valve on washer’s
hot (H) water inlet valve. Screw on coupling by hand until
it is seated on the check valve.
2. Attach the cold water hose to the check valve on washer’s
cold (C) water inlet valve. Screw on coupling by hand until
it is seated on the check valve.
3. Using pliers, tighten the couplings with an additional
two-thirds turn.
NOTE: Do not overtighten. Damage to the coupling can result.
8
4. Turn on the water faucets completely and check for leaks
at water faucets and washer connections.
NOTE: Replace inlet hoses after 5 years of use to reduce the
risk of hose failure. Record hose installation or replacement
dates on the hoses for future reference.
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
Connect the Drain Hose
Remove drain hose from washer drum
1. Using locking pliers, squeeze hose clamp tabs together
and insert over the end of drain hose.
2. Slide drain hose onto washer connection.
3. Once drain hose is in place, release pliers.
Washer drain system can be installed using a floor drain,
wall standpipe, floor standpipe, or laundry tub.
Laundry tub drain or standpipe drain
Connect the drain hose form to the corrugated drain hose.
To keep drain water from going back into the washer:
■ Use the drain hose form and do not force excess drain hose
into standpipe. Hose should be secure but loose enough
to provide a gap for air.
■ Do not lay excess hose on the bottom of the laundry tub.
Floor drain
You may need additional parts. See “Floor drain” under
“Tools and Parts.”
Secure the Drain Hose
Drain hose must be secured to stop the hose from moving when
water is pumped out. If the drain hose moves, water may end up
on the floor.
1. Drape the power cord over the washer top.
2. Move the washer to its final location.
3. Place the drain hose in the laundry tub or standpipe as shown.
See illustrations A and B.
A B C
NOTES:
■ Do not force excess drain hose back into the rear of
the washer.
■ To avoid siphoning, do not seal or put more than 4½"
(114 mm) of the drain hose into drainpipe or standpipe.
■ If the washer faucets and the drain standpipe are recessed,
put the hooked end of the drain hose in the standpipe as
shown. See illustration C.
■ It is the responsibility of the installer to install and secure the
drain hose into the provided plumbing/drain in a manner that
will avoid the drain hose coming out of, or leaking from, the
plumbing/drain.
4
1
/2"
(114 mm)
4
1
/2"
(114 mm)
9
Level the Washer
Properly leveling your washer avoids excessive noise and
vibration.
1. Check the levelness of the washer by placing a level on the
top edge of the washer, first side to side, then front to back.
If the washer is against a wall, move the washer out slightly
before tipping back. If the washer is not level, first prop the
front with a wood block and adjust the feet as necessary; then
prop the back and adjust feet as necessary. Repeat this step
until washer is level.
2. Make sure all 4 feet are stable and resting on the floor.
Then check that the washer is perfectly level (use a level).
3. After the washer is level, use a 9/16" open-end wrench to turn
the nuts on the feet tightly against the washer cabinet.
IMPORTANT: All 4 feet must be tightened. If the nuts are
not tight against the washer cabinet, the washer may vibrate.
4. The washer should not move front to back, side to side,
or diagonally when pushed on its top edges.
5. Slide the washer to its final location.
6. Confirm the levelness of the washer.
Complete Installation
1. Check the electrical requirements. Be sure that you have the
correct electrical supply and the recommended grounding
method. See “Electrical Requirements.”
2. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
3. Check that you have all of your tools.
4. Dispose of/recycle all packaging materials.
5. Check that the water faucets are on.
6. Check for leaks around faucets and inlet hoses.
7. Plug into a grounded 3 prong outlet.
8. To test and clean your washer, measure ½ of the detergent
manufacturer’s recommended amount of High Efficiency (HE)
detergent for a medium-size load. Pour the detergent into
the detergent dispenser. Select any cycle and allow the
washer to complete one whole cycle.
Jam nut
Jam nut
Jam nut
Jam nut
10
NOTE: After the washer has been installed and plugged in,
the display may show ‘0 MINUTES’. Once the washer has been
plugged in and the washer door opened and closed, the display
will show the price. In washers set for free cycles, the display will
flash ‘SELECT CYCLE’.
1. Insert coins until ‘SELECT CYCLE’ flashes in display.
2. Door must be closed before cycle selection is made,
3. Press fabric setting button for the wash cycle desired. After
the cycle is started, the time will display and count down.
4. If a cycle is interrupted by opening the door, ‘RESELECT
CYCLE’ will flash in the display. To restart the washer, close
door and reselect desired cycle.
General User Information
SCROLLING ‘OUT OF ORDER’ SHOWING IN DISPLAY
This condition indicates the washer is inoperative.
‘0 MINUTES’ SHOWING IN DISPLAY
This indicates the cycle is complete and the washer cannot be
operated. Coins dropped or debit inputs during this condition will
be stored in escrow but cannot be used until normal operation is
restored by opening and closing the door. If a door switch fails,
it must be replaced before normal operation can be restored.
COLD START (Initial first use)
Washer is programmed at the factory as follows:
11-minute wash period
3 rinses (extra rinse not enabled)
$2.00 wash price (9150 model)
$0 wash price (9160 model)
WARM START (after power failure)
A few seconds after power is restored, if a cycle was in progress
at the time of the power failure, ‘RESELECT CYCLE’ will flash
in the display, indicating the need for a button press to restart
the washer.
DOOR LOCK
Prior to beginning a cycle, there is a door lock routine of lock/
unlock/relock; then the cycle begins. The door will remain locked
until the end of a cycle or approximately 2 minutes after a power
interruption.
PRICING
After the door is opened following the completion of a cycle,
the display indicates the cycle price (unless set for free operation).
As coins are dropped or debit inputs arrive, the display will change
to lead the user through the initiation of a cycle.
FREE CYCLES
This is established by setting the cycle price to zero. When this
happens, ‘SELECT CYCLE’ will appear rather than a cycle price.
DEBIT CARD READY
This washer is debit card ‘cable’ ready. It will accept a variety of
debit card systems but does NOT come with a debit card reader.
Refer to the debit card reader manufacturer for proper washer
setup. In models converted to a Generation 1 debit card system,
debit pulses represent the equivalent of one coin (coin 1).
Control Set-Up Procedures
IMPORTANT: Read all instructions before operating.
9150 Models: Insert access door key, turn, and lift to remove
access door.
9160 Models: Once the debit card reader is installed (according
to the reader manufacturer’s instructions), the set-up mode can
only be entered by inserting a set-up card (supplied by the reader
manufacturer) into the card slot. If a set-up card is not available,
diagnostic modes can be entered by removing connector AA1
on the circuit board or by using the Service Access Code (see
“Service Access Code” section, page 13) for 9160 models.
IMPORTANT: Unplug washer or disconnect power before opening
the console. To access connector AA1:
1. Unplug washer or disconnect power.
2. Open console, disconnect plug on AA1, and close console.
3. Plug in washer or reconnect power.
The washer is now in the set-up mode. The lower 3 buttons
and the digital display are used to set up the controls. The display
can contain 4 numbers and/or letters and a decimal point. These
are used to indicate the set-up codes and related code values
available for use in programming the washer.
Once the washer has been programmed with a Generation 2 card
reader installed, the washer will be in dAS mode permanently and
dAS will be displayed every time set-up mode is accessed.
The lower fabric setting buttons and the digital display are used
to set up the controls.
The display can contain 4 numbers and/or letters and a decimal
point. These are used to indicate the set-up codes and related
code values available for use in programming the washer.
HOW TO USE THE BUTTONS TO PROGRAM THE CONTROLS
1. The Hot button is used to adjust the values associated with
set-up codes. Pressing the button will change the value by
increments. Rapid adjustment is possible by holding down
the button.
2. The Warm button will advance through the set-up codes. Press-
ing the button will advance to the next available set-up code.
Holding the button down will automatically advance through the
set-up codes at a rate of 1 per second.
3. The Cold button is used to select or deselect options.
USER & SETUP INSTRUCTIONS
11
Start Operating Setup
Before proceeding, it is worth noting that, despite all of the
options available, an owner can simply choose to uncrate a
new commercial washer, hook it up, plug it in, and have a washer
that operates.
Washers are preset at the factory for an 11-minute wash period
and 3 rinses (no extra rinse).
SET-UP CODES
■ The
WARM
button will advance you from code to code.
■ The
HOT
button will change the code value.
■ The
COLD
button will select or deselect options.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two
or three right-hand characters.
NOTE: The first line of each code indicates the factory default
for 9150 models.
CODE EXPLANATION
6. 08
REGULAR CYCLE PRICE (Factory Default)
6.
08
When the d.xx is set to d.00, this 6.xx value
represents the number of coins needed to start the
washer; may adjust from 0–39. Change this value
by pressing the HOT button. 6.08 = 8 coins. 9160
models default to 6.00.
6. 01
g
When the d.xx is set to d. CS, this 6.xx value
represents the number of push-in actuations of the
coin slide to start the washer. 6.01 would equal one
coin slide activation.
Press the
WARM
button once to advance
to next code.
7. 11
WASH LENGTH
7. 11
g
This is the number of minutes for WASH. Washer
comes from the factory preset with 11 minutes.
Choose from 9–17 minutes by pressing the HOT
button.
Press the
WARM
button once to advance
to next code.
8.
00
ADDITIONAL RINSE OPTION
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’.
8.
8.
00
Ar
g
Not Selected ‘OFF’.
Selected ‘ON’.
Press the
COLD
button once for this selection.
Press the
WARM
button once to advance
to next code.
9.
00
CYCLE COUNTER OPTION
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’.
9.
9.
00
0C
g
Not Selected ‘OFF’.
Selected ‘ON’ and not able to be deselected.
Press the
COLD
button 3 consecutive times to select
‘ON’. Once selected ‘ON,’ it cannot be deselected.
Press the
WARM
button once to advance
to next code.
1.
00
MONEY COUNTER OPTION
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’.
CODE EXPLANATION
1.
1.
1.
00
0C
C0
g
Not Selected ‘OFF’.
Selected ‘ON’.
Press the
COLD
button three consecutive times
to select ‘ON’ and three consecutive times to remove
(Not Selected ‘OFF’). Counter resets by going
from ‘OFF’ to ‘ON’.
Selected ‘ON’ and not able to be deselected.
To select ‘ON’ and not able to be deselected,
first select ‘ON’, then within two seconds, press
the
COLD
button twice,
HOT
once, and exit
the set-up mode.
Press the
WARM
button
once to advance
to next code.
2. 00
SPECIAL PRICING OPTIONS
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’.
2. 00 Not Selected ‘OFF’.
2. SP
g
Selected ‘ON’. Press the COLD button once for this
selection.
If SPECIAL PRICING OPTION is selected, there
is access to codes ‘3.’ thru ‘9.’
Press the
WARM
button
once to advance
to next code.
OPTIONS TO USE IF SPECIAL PRICING
IS SELECTED:
3. 08
SPECIAL CYCLE PRICE
3. 08 Represents the number of quarters (coin 1) needed
to start the washer; may adjust from 0–39. (See b.xx
setup for VALUE OF COIN 1.) Advance from 0–39 by
pressing HOT. Factory default of 8 quarters = $2.00.
3. 00
g
Model 9160: Factory default of 0 quarters.
Press the
WARM
button
once to advance
to next code.
5. 00
TIME-OF-DAY CLOCK, MINUTES
5. 00
g
This is the TIME-OF-DAY CLOCK, minute setting;
select 0–59 minutes by pressing the HOT button.
Press the
WARM
button
once to advance
to next code.
6. 00
TIME-OF-DAY CLOCK, HOURS
NOTE: Uses military time – 24 hr. clock.
6. 00
g
This is the TIME-OF-DAY CLOCK, hour setting;
select 0–23 hours by pressing the HOT button.
Press the
WARM
button
once to advance
to next code.
7. 00
SPECIAL PRICE START HOUR
NOTE: Uses military time – 24 hr. clock.
7. 00
g
This is the start hour; select 0–23 hours. Select
START HOUR by pressing the HOT button.
Press the
WARM
button
once to advance
to next code.
8. 00
SPECIAL PRICE STOP HOUR
NOTE: Uses military time – 24 hr. clock.
8. 00
g
This is the stop hour; select 0–23 hours. Select STOP
HOUR by pressing the HOT button.
Press the
WARM
button
once to advance
to next code.
12
CODE EXPLANATION
9. 10
SPECIAL PRICE DAY
9. 10
g
This represents the day of the week and whether
special pricing is selected for that day. A number
followed by ‘0’ indicates no selection for that
particular day (9.10). A number followed by
an ‘S’ indicates selected for that day (9.1S).
Day of week (1–7) can be chosen by pressing the
HOT button. Press the COLD button once to select
special pricing for each day chosen.
When exiting set-up code ‘9.’, the display must show
current day of week:
DISPLAY DAY OF WEEK CODE (selected)
10 Day 1= Sunday 1S
20 Day 2 = Monday 2S
30 Day 3 = Tuesday 3S
40 Day 4 = Wednesday 4S
50 Day 5 = Thursday 5S
60 Day 6 = Friday 6S
70 Day 7 = Saturday 7S
Press the
WARM
button once to advance
to next code.
A. 00
VAULT VIEWING OPTION
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’.
A. 00 Not Selected ‘OFF’.
A. SC
g
Selected ‘ON’. Press the COLD button once for this
selection. When selected, the money and/or cycle
counts will be viewable (if counting is selected)
when the coin box is removed.
Press the
WARM
button once to advance
to next code.
b. 40
VALUE OF COIN 1
b. 05
g
This represents the value of coin 1 in number
of nickels: 05 = $0.25.
By pressing the
HOT
button, there is an option
of 1–199 nickels.
With coin slide activation, this represents the total
vend price in nickels. Example: b.40 is equal to
$2.00.
Press the
WARM
button once to advance
to next code.
C. 20
VALUE OF COIN 2
C.
C.
20
05
g
This represents the value of coin 2 in number
of nickels: 20 = $1.00.
By pressing the
HOT
button, there is the option
of 1–199 nickels.
Press the
WARM
button once to advance
to next code.
d.
00
COIN SLIDE OPTION
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’. Replacement of meter case
will be needed for coin slide mounting.
d. 00 Not Selected ‘OFF’.
CODE EXPLANATION
d. CS
g
Selected ‘ON’.
NOTE: This option needs to be set to ‘00’ unless the
meter case has been changed to accept a coin slide
device.
Press the COLD button 3 consecutive times for this
selection. When coin slide mode is selected, set ‘b.’
equal to value of vend price in nickels. Set ‘6 XX’
(REGULAR CYCLE PRICE) and ‘3.XX’ (SPECIAL
CYCLE PRICE) to number of slide operations.
NOTE: If the installer sets up ‘CS’ on a coin drop
model, the washer will not register coins inserted.
Press the
WARM
button once to advance
to next code.
E. 00
ADD COINS OPTION
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’. This option causes the customer
display to show the number of coins (coin 1) to enter,
rather than the dollars-and-cents amount.
E. 00 Not Selected ‘OFF’.
E. AC
g
Selected ‘ON’.
Press the COLD button 3 consecutive times for this
selection.
PR MODELS ONLY: In enhanced debit mode, this
option is not selectable.
Press the
WARM
button once to advance
to next code.
F. 00
ENHANCED PRICING OPTION
F.
F.
00
SU
g
Not Selected ‘OFF’.
Super Cycle pricing enabled. This option allows
customers to upgrade cycles by depositing extra
money. Set-up codes ‘H.’ and ‘h.’ will be displayed
only when this option is enabled. Press the COLD
button for this selection.
Press the WARM button once to advance to next
code.
H. 01
SUPER CYCLE UPGRADE PRICE
(Skipped unless Super Cycle pricing is enabled.)
H. 01
g
This represents the number of coin 1 required to
upgrade a base cycle to a Super Cycle. Advance
from 0–33 by pressing the HOT button.
Press the WARM button once to advance to next
code.
h. 01
SUPER CYCLE TYPE
(Skipped, unless Super Cycle pricing is enabled.)
h. 01
g
This represents the Super Cycle upgrade option.
Press the HOT button to step through upgrade
options 1 through 3 as follows:
01 – enhanced wash, extra 3 minutes of wash tumble
in addition to the programmed wash time.
02 – extra rinse for all cycles.
03 – both 01 and 02.
Press the WARM button once to advance to next
code.
13
CODE EXPLANATION
J. Cd
COIN/DEBIT OPTION
J.
J.
J.
J.
Cd
C_
_d
Ed
g
Both coin and debit selected. Press the
COLD
button
3 consecutive times for this selection (default for
9150 models).
Coins selected, debit disabled. Press the
COLD
button 3 consecutive times for this selection.
Debit card selected, coins disabled. Press the COLD
button 3 consecutive times for this selection (default
for 9160 models).
Enhanced Debit is self-selected when a Generation 2
card reader is installed in the washer. The Ed option
cannot be manually selected or deselected.
Press the
WARM
button once to advance
to next code.
L. 00
PRICE SUPPRESSION OPTION
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’. This option causes the customer
display to show ‘AVAILABLE’ or ‘ADD’ rather than
the amount of money to add (used mainly in debit
installations).
L. 00 Not Selected ‘OFF’.
L. PS
g
Selected ‘ON’. Press the COLD button once for this
selection.
Press the
WARM
button once to advance
to next code.
n. CE
CLEAR ESCROW OPTION
When selected, money held in escrow for
30 minutes without further escrow or cycle
activity will be cleared.
n.
n.
00
CE
g
Not Selected ‘OFF’.
Selected ‘ON’. Press the
COLD
button once for
this selection.
Press the
WARM
button once to advance to
next code.
U. 00
PENNY INCREMENT OFFSET
U. 00
g
This represents the penny increment price offset
used with Generation 2 (Enhanced Debit) card
readers. Choose from 0–4 pennies by pressing
the HOT button.
Press the
WARM
button once to advance
to next code.
A1.
00
PREWASH LENGTH
A1.
00
g
This is the number of minutes of PREWASH. Choose
0 to disable the prewash or select between 2 and 7
minutes by pressing the
HOT
button.
Press the
WARM
button once to advance
to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Represents the number
of cycles in HUNDREDS
1 02 = 200
2 00 Represents the number
of cycles in ONES
2 25 = 25
TOTAL CYCLES = 225
3 00 Number of dollars
in HUNDREDS
3 01 = $100.00
4 00 Number of dollars in ONES 4 68 = $ 68.00
5 00 Number of CENTS 5 75 = $ .75
TOTAL = $168.75
This is “VIEW ONLY” and cannot be cleared.
Press the
WARM
button once to advance to next code.
If money counter (1.0C or 1.C0) is selected, the following
is true:
END OF SET-UP PROCEDURES
EXIT FROM SET-UP MODE
CHW9150 Models:
Reinstall access door.
CHW9160 Models:
1. Unplug washer or disconnect power.
2. Open console, reinsert plug into AA1, and close console.
3. Plug in washer or reconnect power.
MODEL CHW9150 SET UP AS PN WITH PROGRAMMING
SWITCH:
Turn key clockwise and remove.
MODEL CHW9160 SET UP AS PN WITHOUT PROGRAMMING
SWITCH:
Set-up mode can be exited by using procedures from “Service
Access Code.”
SERVICE ACCESS CODE
This code can be entered to access service mode without
removing the console. It only functions on washers set up for 0
vend price without any Special Pricing setup, and the Coin/Debit
Option must be set to “J._d”. If the washer is not in failure mode,
the door must be opened to proceed. Service Access Code
contains 4 steps. Perform the following steps:
1. Press the upper left button.
2. Press the lower right button.
3. Press the upper right button.
4. Press the lower left button.
NOTE: If the Service Access Code procedure is not completed
properly, as noted above, there is a 15-second delay before it can
be attempted again.
There are 3 options to exit from the Service Mode:
1. From Set-up Code 8, press button #1 for 4 seconds.
2. Wait 2 minutes without touching any buttons (without
diagnostic modes running).
3. Power down the washer; then reapply power.
14
Cleaning Your Washer
Cleaning the Door Seal/Bellow
1. Open the washer door and remove any clothing or items from
the washer.
2. Inspect inner glass door. If debris is present, wipe off debris
using damp cloth.
3. Inspect the colored seal/bellow between the door opening
and the drum for stained areas. Pull back the seal/bellow
to inspect all areas under the seal/bellow and to check for
foreign objects.
A
A. Seal/Bellow
4. If stained areas are found, wipe down these areas of the seal/
bellow using the procedure that follows:
a) Mix a dilute solution, using 3/4 cup (177 mL) of liquid
chlorine bleach, and 1 gal. (3.8 L) of warm tap water.
b) Wipe the seal/bellow area with the dilute solution,
using a damp cloth.
c) Let stand 5 minutes.
d) Wipe down area thoroughly with a dry cloth and let
the washer interior air dry with door open.
IMPORTANT:
■ Wear rubber gloves when cleaning for prolonged periods.
■ Refer to the bleach manufacturer’s instructions for proper use.
Washer Maintenance Procedure
This washer has a special cycle that uses higher water volumes
in combination with liquid chlorine bleach to thoroughly clean
the inside of the washer.
NOTES:
■ Read these instructions completely before beginning the
cleaning process.
■ If necessary, the cleaning cycle may be interrupted by
pressing the
COLD
button twice. However, this will not
immediately stop the cycle. The washer will continue with
several rinse and drain steps to ensure that all remaining
bleach is rinsed from the washer.
Begin procedure
1. Open the washer door and remove any clothing or items from
the washer.
2. Use liquid chlorine bleach:
Open the dispenser drawer and immediately add 2/3 cup
(160 mL) of liquid chlorine bleach to the bleach compartment.
NOTE: Do not add any detergent to this cycle. Use of more
than 2/3 cup (160 mL) of bleach will cause product damage
over time.
3. Close the washer door and the dispenser drawer.
4. To start the Clean Washer cycle, first enter “Start Operating
Set-up.” Then press and hold
COLD
for 1 second. With
the entire display flashing, press
COLORS/DELICATES
.
NOTE: The drum will rotate, then the door will unlock,
lock again, and then the cycle will continue.
■ The washer will not fill, but the drum will rotate while
the washer runs a short sensing cycle. This will take
approximately 3 minutes.
5. The cycle will determine whether clothing or other items are
in the washer.
a) If no items are detected in the washer, it will proceed
to Step 7.
b) If any items are detected in the washer, “rL” or “F-34”
will be displayed. Then the door will unlock.
■ Press
COLD
to cancel the failure code. Then repeat steps
1, 3, and 4 to start the cycle again.
6. Once the cycle has begun, allow the cycle to complete.
7. After the cycle is complete, leave the door open slightly
to allow for better ventilation and drying of washer interior.
Always do the following to maintain washer freshness:
■ Use only “HE” High Efficiency detergent.
■ Leave the door slightly open after each cycle to allow
for better ventilation and drying of washer interior.
■ Clean the washer monthly using the Washer Maintenance
Procedure and 2/3
cup (160 mL)
of liquid chlorine bleach.
■ If the procedure does not sufficiently improve the washer
freshness, please evaluate your installation and usage
conditions for other causes.
Cleaning the exterior
Use a soft damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to keep it looking
new. Use mild soap and water. Do not use abrasive products.
Cleaning the dispenser drawer
The dispenser drawer is removable for easy cleaning.
1. Unlock the dispenser drawer by pressing the Release Lever.
Remove the drawer.
2. Remove the inserts (the siphon from the softener and bleach
compartments).
3. Wash the parts under running water.
NOTE: Do not wash components in the dishwasher.
4. Re-install the inserts and return the dispenser to the drawer.
Water Inlet Hoses
Replace water inlet hoses after 5 years of use to reduce
the risk of hose failure. Periodically inspect and replace water
inlet hoses if bulges, kinks, cuts, wear, or leaks are found.
When replacing your water inlet hoses, mark the date
of replacement on the label with a permanent marker.
ASSISTANCE OR SERVICE
If you need assistance:
Contact the distributor where the washer was purchased; locate
an authorized Whirlpool Commercial Laundry distributor or visit
www.whirlpoolcommerciallaundry.com.
When you call, have the washer model number and serial
number. Both numbers can be found on the serial/rating plate
located on your washer.
WASHER CARE
15
WHIRLPOOL
®
COMMERCIAL LAUNDRY
LIMITED WARRANTY
1. All other costs including labor, transportation, shipping, or custom duties for
covered parts.
2. Factory specified replacement parts if this commercial appliance is used for other
than normal, commercial use or when it is used in a manner that is inconsistent to
published user or operator instructions and/or installation instructions.
3. Service calls to correct the installation of your commercial appliance, to instruct
you on how to use your commercial appliance, to replace or repair house fuses,
or to correct external wiring or plumbing.
4. Service calls to repair or replace appliance light bulbs, air filters, or water filters.
Consumable parts are excluded from warranty coverage.
5. Damage resulting from improper handling of product during delivery, theft,
accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation,
installation not in accordance with local electrical or plumbing codes, or use of
products not approved by Whirlpool.
6. Pick up and delivery. This commercial appliance is designed to be repaired on
location.
7. Repairs to parts or systems resulting from unauthorized modifications made to
the commercial appliance.
8. The removal and reinstallation of your commercial appliance if it is installed in an
inaccessible location or is not installed in accordance with published installation
instructions.
9. Damage resulting from exposure to chemicals.
10. Changes to the building, room, or location needed in order to make the
commercial appliance operate correctly.
11. Factory specified replacement parts on commercial appliances with original
model/serial numbers that have been removed, altered, or cannot be easily
determined.
12. Discoloration, rust, or oxidation of stainless steel surfaces.
13. Factory specified replacement parts as a result of incorrect diagnosis or repair
by an “out of network” service company.
The cost of repair or replacement under these excluded circumstances shall
be borne by the customer.
90 DAY LIMITED WARRANTY
(PARTS AND LABOR)
For 90 days from the original date of purchase, when
this commercial appliance is installed, maintained, and
operated according to the instructions attached to
or furnished with the product, Whirlpool Corporation
(hereafter “Whirlpool”) will pay for factory specified
replacement parts and repair labor to correct defects
in materials or workmanship that existed when this
commercial appliance was purchased.
TWO YEAR LIMITED WARRANTY
(PARTS ONLY)
For the first two years from the original date of
purchase, when this commercial appliance is installed,
maintained, and operated according to the instructions
attached to or furnished with the product, Whirlpool will
pay for factory specified replacement parts to correct
defects in materials or workmanship that existed when
this commercial appliance was purchased.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS
LIMITED WARRANTY SHALL BE PRODUCT REPAIR
AS PROVIDED HEREIN. Whirlpool recommends that
you use an “in network” service provider to diagnose
and repair your Commercial Laundry product.
Whirlpool will not be responsible under this warranty
to provide additional replacement parts as a result of
incorrect diagnosis or repair by an “out of network”
service company. This limited warranty is valid in the
United States or Canada and applies only when the
commercial appliance is used in the country in which
it was purchased. This limited warranty is effective
from the date of the original consumer purchase. Proof
of original purchase date is required to obtain service
under this limited warranty.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO TWO YEARS OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do
not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty
gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the
exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty
gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the
representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes
with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.
08/16
IF YOU NEED SERVICE:
Contact your authorized Whirlpool
®
Commercial Laundry distributor. To locate your authorized Whirlpool
®
Commercial Laundry distributor, call:
1-800-662-3587, or for web inquiries, visit www.WhirlpoolCommercialLaundry.com.
For written correspondence:
Whirlpool
®
Commercial Laundry Service Department
2000 N M 63
Benton Harbor, Michigan 49022-2632 USA
90 DAY LIMITED WARRANTY
WHAT IS COVERED
WHAT IS NOT COVERED
16
SÉCURITÉ DE LA LAVEUSE
17
EXIGENCES D’INSTALLATION
Autres pièces
Il se peut que l’installation nécessite des pièces supplémentaires.
Pour acheter l’un des articles indiqués ici, composer le numéro
sans frais indiqué à “Accessoires”.
Si vous avez Vous devrez acheter
Évier de buanderie ou
tuyau rigide de rejet à
l’égout plus haut que
96" (2,4 m)
Système de pompe de puisard
(si non déjà disponible)
Égout surélevé Évier de vidange standard de
20 gal. (76 L) de 30" (762 mm) de
hauteur ou évier utilitaire et pompe
de puisard (disponibles chez votre
fournisseur local d’articles de
plomberie)
Égout au plancher Brise-siphon, pièce n° 285834;
tuyau de vidange additionnel,
pièce n° 8318155; et ensemble
de connexion, pièce n° 285835
Tuyau de vidange trop
court
Trousse de rallonge du tuyau de
vidange de 4 pi (1,2 m), pièce n°
285863
Robinets d’eau hors
d’atteinte des tuyaux
d’admission
2 tuyaux d’admission d’eau plus
longs :
6 pi (1,8 m), pièce n° 76314
10 pi (3,0 m), pièce n° 350008
Outillage et pièces
Rassembler les outils et pièces nécessaires avant de commencer
l’installation. Les pièces fournies se trouvent dans le tambour
de la laveuse.
Outils nécessaires au raccordement des tuyaux d’arrivée
d’eau :
■ Pince (ouverture jusqu’à
1
9
⁄16" [39,5 mm])
■ Lampe de poche
(facultative)
Outils nécessaires à l’installation :
■ Clés plates de 1/2"
et 9/16"
■ Tournevis de sécurité
TORX
®
T20
®†
■ Tourne-écrou de 1/4"
■ Niveau
■ Cale en bois
■ Règle ou mètre ruban
Pièces fournies :
Accessoires
Vous pouvez faciliter l’utilisation de votre laveuse avec
ces accessoires de première qualité.
Pour vous informer au sujet des autres articles de qualité
ou pour commander, composer le 1-866-698-2538
ou consulter le site www.whirlpool.com/accessories.
Au Canada, composer le 1-800-688-2002 ou consulter
le site Internet www.whirlpoolparts.ca.
Produit numéro Accessoire
8212526
Plateau d’égouttement de la laveuse,
convient à tous les modèles
31682
Produit de nettoyage polyvalent pour
appareils ménagers
1903WH
Casier de rangement de fournitures
de buanderie
A. Bride de retenue pour tuyau
de vidange (en forme de U)
B. Tuyaux d’arrivée d’eau (2)
C. Rondelles pour tuyau
d’arrivée d’eau (4)
†®TORX et T20 sont les marques déposée de Acument Intellectual Properties, LLC.
A B
C
E
D
D. Bouchons pour les trous
des boulons de transport (4)
E. Attache de fixation amovible
18
Exigences d’emplacement
Le choix d’un emplacement approprié pour la laveuse
en améliore le rendement et réduit au minimum le bruit
et le “déplacement” possible de la laveuse.
La laveuse peut être installé sous un comptoir personnalisé,
dans un sous-sol, une salle de buanderie ou un encastrement.
Voir “Système de vidange”.
Il faut aussi prendre en compte les exigences d’emplacement des
appareils voisins. C’est à l’utilisateur qu’incombe la responsabilité
de réaliser une installation correcte.
Il vous faudra :
■ Un chauffe-eau configuré pour fournir de l’eau à 120°F
(49°C) à la laveuse.
■ Une prise électrique reliée à la terre située à moins de
6 pi (1,8 m) du cordon d’alimentation électrique fixé à
l’arrière à la laveuse. Voir “Spécifications électriques”.
■ Des robinets d’eau chaude et d’eau froide situés à moins
de 4 pi (1,2 m) des robinets d’admission d’eau chaude
et d’eau froide et une pression d’eau de 20–100 lb/po²
(137,9–689,6 kPa).
■ Un plancher de niveau ayant une pente maximale de
1" (25 mm) sous l’ensemble de la laveuse. L’installation
de la laveuse sur des surfaces de sol molles, telles que
tapis ou surfaces avec sous-couche en mousse, n’est pas
recommandée.
■ Un plancher robuste et solide capable de soutenir le poids
total de la laveuse (eau et charge) de 400 lbs (180 kg).
Ne pas faire fonctionner la laveuse à des températures inférieures
à 32ºF (0ºC). Une quantité d’eau peut demeurer dans la laveuse
et causer des dommages à des températures basses.
Dégagements de séparation à respecter
■ L’emplacement doit être assez grand pour permettre d’ouvrir
complètement la porte de la laveuse.
■ Prévoir davantage d’espace pour faciliter l’installation
et l’entretien. La porte s’ouvre à plus de 90° et n’est pas
réversible.
■ Un espace supplémentaire peut être requis pour les
moulures de porte et de plancher et pour les plinthes.
Options
Piédestal
Vous avez la possibilité d’acheter des piédestaux séparément
pour cette laveuse. Le piédestal augmentera la hauteur totale
de la laveuse.
Piédestal facultatif
Hauteur du
piédestal
Hauteur
approximative
avec laveuse
Couleur
Numéro
de modèle
2
7
⁄8" (73 mm)
47½" (1207 mm)*
Blanc WHP0400VW
*Ajouter 5/8" (16 mm) minimum pour les pieds de nivellement.
■ Un espace supplémentaire de 1" (25 mm) de tous les côtés
de la laveuse est recommandé pour réduire le transfert
du bruit.
■ Il faut aussi prendre en compte l’espace requis entre
les appareils voisins.
Installation dans un encastrement
Cette laveuse peut être installée dans un encastrement.
Les dimensions d’installation indiquées correspondent à
l’espacement minimal permis. Prévoir davantage d’espace
pour faciliter l’installation et l’entretien. Consulter le tableau
ci-dessous.
Espaces requis pour installation
(Utiliser l’espace de dégagement recommandé
pour une installation plus facile.)
Recommendée/Minimum
Arrière/Dessus Côtes
En retrait/sous comptoir 0"/0"
(0 mm)/(0 mm)
1"/0"
(25 mm)/(0 mm)
*Dimensions de la laveuse
Door is not reversible
28
13
/16"
(732 mm)
44
5
/8"
(1134 mm)
27"
(686 mm)
50 ½"
(1282 mm)
37
13
/
16
"
(961 mm)
*Hauteur sans les pieds de nivellement installés.
REMARQUE : La porte n’est pas réversible.
*
*
19
Un système de vidange au plancher doit être installé sous la
cloison. Des cloisons pré-fabriquées avec prises de courant,
canalisations d’arrivée d’eau, et aménagements pour installation
de vidange ne doivent être installés que là où les codes locaux
l’autorisent.
Système de vidange
La laveuse peut être installé en utilisant le système de rejet à
l’égout (au plancher ou mural), le système de vidange de l’évier
de buanderie ou le système de vidange au plancher. Sélectionner
la méthode d’installation du tuyau de vidange selon les besoins.
Voir “Outillage et pièces”.
Système de vidange avec tuyau de rejet à l’égout – mural
ou au plancher (vues A et B)
Le système de rejet à l’égout nécessite un tuyau rigide
d’un diamètre minimum de 2" (50 mm). La capacité minimale
d’acheminement ne doit pas être inférieure à 12 gal. (45,5 L)
par minute et par laveuse.
Le sommet du tuyau rigide de rejet à l’égout doit être au moins
à 30" (762 mm) de hauteur et au maximum à 96" (2,4 m) de la
base de la laveuse.
Système de vidange avec évier de buanderie
L’évier de buanderie doit avoir une capacité minimale de
20 gal. (76 L). La partie supérieure de l’évier de buanderie
doit être à au moins 30" (762 mm) au-dessus du plancher.
Spécifications électriques
■ Une alimentation de 120 volts, 60 Hz, CA seulement,
de 15 ou 20 ampères, protégée par un fusible est requise.
On recommande d’utiliser un fusible ou un disjoncteur
temporisé. Il est recommandé de raccorder la laveuse
sur un circuit distinct exclusif à cette laveuse.
■ Cette laveuse comporte un cordon d’alimentation électrique
à trois broches pour liaison à la terre.
■ Pour minimiser les risques de choc électrique, on doit
brancher le cordon sur une prise de courant de configuration
correspondante, à 3 alvéoles, reliée à la terre et installée
conformément aux codes et règlements locaux. Si une
prise de courant de configuration correspondante n’est pas
disponible, le client a la responsabilité et l’obligation de
faire installer par un électricien qualifié une prise de courant
correctement reliée à la terre.
■ Si les codes le permettent et si on utilise un conducteur
distinct de liaison à la terre, il est recommandé qu’un
électricien qualifié vérifie la qualité de la liaison à la terre.
■ Ne pas utiliser une tuyauterie de gaz pour le raccordement
à la terre.
■ En cas de doute quant à la qualité de la liaison à la terre
de la laveuse, consulter un électricien qualifié.
■ Ne pas installer un fusible dans le conducteur neutre
ou le conducteur de liaison à la terre.
Système de vidange au plancher
Le système de vidange au plancher nécessite un brise-siphon
qui peut être acheté séparément. Voir “Outillage et pièces”.
Le brise-siphon doit être au moins à 28" (710 mm) de la base
de la laveuse. Des tuyaux supplémentaires peuvent être requis.
30" min.
(762 mm)
A
B
30" min.
(762 mm)
Vue arrière
28" min.
(710 mm)
20
Shipping bolt
2. Au moyen d’une clé de ½", desserrer chacun des boulons.
3. Une fois le boulon desserré, le déplacer au centre du
trou et retirer complètement le boulon, y compris la cale
d’espacement en plastique couvrant le boulon.
4. Une fois que les 4 boulons ont été retirés, jeter les boulons
et les cales d’espacement. Puis pousser la fiche du cordon
d’alimentation électrique à travers l’ouverture sur le côté droit
du panneau arrière, tirer le cordon d’alimentation électrique
à travers l’ouverture sur le côté gauche du panneau arrière
et obturer les trous avec le bouchon fourni. Ne pas tirer
l’extrémité du cordon d’alimentation à travers le trou de droit.
5. Obturer les trous des boulons avec les 4 bouchons
d’obturation des boulons de transport.
REMARQUE : Si la laveuse doit être transporté à une date
ultérieure, appeler le distributeur ou l’installateur du produit. Pour
éviter des dommages concernant la suspension et la structure,
votre laveuse doit être correctement monté pour réinstallation
ultérieure par un technicien certifié.
Boulon
d’expédition
INSTRUCTIONS
D’INSTALLATION
Dépose du système de transport
IMPORTANT : Positionner la laveuse de sorte que l’arrière de la
laveuse soit à environ 3 pi (900 mm) de son emplacement final.
On trouve sur le panneau arrière de la laveuse 4 boulons
d’expédition qui soutiennent le système de suspension durant le
transport. Ces boulons retiennent aussi le cordon d’alimentation
électrique à l’intérieur de la laveuse jusqu’à ce que les boulons
soient retirés.
Boulon d’expédition avec cale d’espacement en plastique
1. Laisser la laveuse en position verticale pendant que l’on ôte
les boulons d’expédition.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Whirlpool CHW9160GW Mode d'emploi
- Catégorie
- Machines à laver
- Taper
- Mode d'emploi
- Ce manuel convient également à