OWNER’S MANUAL
© 2018 MILLER Electric Mfg. LLC
OM-1076 146332C
2018−12
Turntable (146236) For 10, 20, 22A, 24A, 30, 50, S-60, S-70, D-60, D-70 And R115 Series Feeders
1. Safety Symbol Definitions
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
DANGER ! - Indique une situation dangereuse qui, si elle
n’est pas évitée, entraînera la mort ou des blessures
graves. Les éventuels risques sont représentés par les
symboles joints ou expliqués dans le texte.
Fsafe1 2013-10
Beware of electric shock from wiring. Disconnect input
power before installing this kit. Reinstall all panels and
covers.
Attention aux décharges électriques au contact des
câbles. Couper l’alimentation électrique avant d’installer
ce kit. Réinstaller tous les panneaux et couvercles.
Fsafe7 2013-10
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Indique une situation dangereuse qui, si elle n’est pas
évitée, entraînera la mort ou des blessures graves. Les
éventuels risques sont représentés par les symboles
joints ou expliqués dans le texte.
Fsafe2 2013-10
Wear safety glasses with side shields.
Porter des lunettes de sécurité avec écrans latéraux.
Fsafe8 2013-10
NOTICE
Indicates statements not related to personal injury.
Signale des consignes non associées aux dommages
corporels.
Indicates special instructions.
Fournit des instructions spéciales.
Fsafe3 2013-10
Tools and filings can damage parts inside unit. Cover and
protect parts before starting installation. Clean unit and
remove covers before operating unit.
Les outils et la limaille peuvent endommager des pièces
de l’appareil. Recouvrir et protéger les pièces avant
de commencer l’installation. Découvrir et nettoyer
l’appareil avant le travail.
Fsafe14 2013-10
CALIFORNIA PROPOSITION 65 WARNINGS
WARNING: Cancer and Reproductive Harm − www.P65Warnings.ca.gov
PROPOSITION CALIFORIENNE 65 AVERTISSEMENTS
AVERTISSEMENT : cancer et troubles de la reproduction − www.P65Warnings.ca.gov.
Fsafe26 2018-01
OM-1076 Page 2
ST-147347-A / ST-146963 / ST-800285
Part
No.
Item
No.
1 602101 Screw, 10-24 x 5/8 (8)
2 602203 Washer, No. 10 lock (12)
3 146296 Stand-Off, No. 10-24 x 1-9/16 (4)
4 604247 Screw, 10-24 x 3/8 (12)
5 146294 Cover (1)
6 146295 Turntable (2)
7 146297 Stand-Off, No. 10-24 x 11/16 (4)
8 146293 Tray (1)
9 146298 Base (1)
602111 Screw, 10-24 x 1 (4)
Base Mounting Hardware
602111 Screw, 10-24 x 1 (4)
602101 Screw, 10-24 x 5/8 (8)
602203 Washer, No. 10 lock (8)
146296 Stand-Off, No 10-24 X 1-9/16 (4)
! Remove cover from welder before drilling
holes.
Be sure to provide Model when ordering replace-
ment parts.
Description (Total Qty)
5
5/16 in.
Tools Needed:
CA AC
B
CA AC
B
B
4
2
6
7
8
6
2
4
9
4
3
2
1
Top View
. For S−60, S−70 and 20 Series feeders, install stand−offs (3) onto
turntable tray (8) in holes labeled A with four 10−24 x 5/8 in. screws
(1) and washers (2). Then secure feeder base to stand−offs (3) with
four 10−24 x 5/8 in. screws (1) and washers (2).
For D−60 and D−70 Series feeders, install stand−offs (3) onto
turntable tray (8) in holes labeled C with four 10−24 x 5/8 in. screws
(1) and washers (2). Then secure feeder base onto stand−offs (3)
with four 10−24 x 5/8 in. screws (1) and washers (2).
For 50 series feeders, install stand−offs (3) onto turntable tray (8) in
holes labeled A with four 10−24 x 5/8 in. screws (1) and washers (2).
Then secure feeder base onto stand−offs (3) with four 10−24 x 1 in.
screws (10) and washers (2)
For 22A, 24A and R115 feeders, install stand−offs (3) onto turntable
tray (8) in holes labeled B with three 10−24 x 5/8 in screws (1) and
washers (2). Remove two rear feet from feeder base. Then secure
feeder base onto stand−offs with three 10−24 x 5/8 in. screws (1)
and washers (2).
For 10 and 30 series feeders, mark and drill four 7/32 in (6 mm) holes
in feeder base matching turntable tray (8) holes labeled A. Install
stand−offs (3) onto turntable tray (8) in drilled holes. Then secure
feeder base onto stand−offs (3) with four 10−24 x 1 in. screws (10)
and washers (2).
-
1
-
2
Miller TURNTABLE (146236) Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
Documents connexes
-
Miller PROHEAT SERIES ADAPTOR (195 437) Le manuel du propriétaire
-
-
-
-
-
-
-