Quickstart Guide
Guide de démarrage rapide
Guía de inicio rápido
S3 Coding Module™
55527H0 - No power
55527HC - w/ USB power
Important
Before using this product:
• Read this manual
• Comply with all safety and operating instructions
• Ensure all parts and correct quantities are included
Important
Avant d’utiliser ce produit:
• Veillez à lire ce guide
• Respectez les consignes de sécurité et d’utilisation
• Vériez que vous disposez de toutes les pièces
nécessaires à l’installation
Importante
Antes de utilizar este producto:
• Lea este manual
• Cumpla con todas las instrucciones de prevención de
accidentes y operativas
• Revise que todas las partes y las cantidades correctas
estén incluidas
Any parts damaged during shipment must be reported within 5
days of receipt. To report information regarding missing parts or
damage, to purchase parts or accessories, or if you have any
questions, please contact us.
Thank you for purchasing Spectrum products!
Les pièces endommagées pendant le transport doivent faire
l’objet d’un rapport dans les 5 jours de leur réception. Veuillez
prendre contact avec nous si des pièces manquent ou sont
abîmées, si vous avez des questions, ou encore pour acheter
des pièces ou des accessoires.
Merci pour votre achat d’un produit Spectrum!
Si alguna parte se dañó durante el embarque, deberá reportarla
en un lapso de 5 días a partir de la recepción. Para reportar
cualquier información sobre partes faltantes o dañadas, para
adquirirlas o comprar accesorios, o bien, si tiene alguna duda,
póngase en contacto con nosotros.
¡Gracias por adquirir productos Spectrum!
??
Owner’s Manual
Le manuel du propriétaire
El manual del propietario
Video
Vidéo
Vídeo
Specs
Spécications
Especicaciones
800-235-1262
http://www.spectrumfurniture.com
0191559R1 Page 1 of 9
Owner’s Manual
Le manuel du propriétaire
El manual del propietario
Video
Vidéo
Vídeo
Specs
Spécications
Especicaciones
800-235-1262
55527HC w/ USB power includes:
(1) 0191567
Splitter
(2) 0191496
6-Port USB chargers
0191559R1 Page 2 of 9
(4) 0190174
#8 x 3/8”PHSM
(2) 042749
#8 x 1” PHSM
(2) 0147900
Slide bracket
Hardware
(2) 0191218
Shallow tray
(2) 0147973
Divider tabs
(2) 0147925
Universal panel
(1) 0147901
Tray
(2) 0145039
Bar support B-side
(with slots)
(4) 056284
8-32 Wing nut
(2) 0142528
Bar support
(with threaded weld studs)
Components
Left slotted
uprights
Right slotted
uprights
Front bar Assembly
Rear bar Assembly
0191559R1 Page 3 of 9
Assemble bar supports
1. The bars should be assembled with the tabs facing away from
each other as shown in Figure 1.
2. Loosen the (2) wingnuts slightly.
3. Repeat for the 2nd set of bars.
1
X 2
Bar support B-side
(with slots)
Bar support
(with threaded weld studs)
8-32 Wing nut
(2 per assembly)
Tab
Tab
Figure 1
1. Determine the approximate location (height) you would like the
module to be mounted. The rear bar is (1) slot higher than the front.
2. Insert one tab into a slot in the left slotted upright. Figure 2.
3. Insert the opposite tab into the corresponding right slotted upright
and fully extend the bar assembly into place.
4. Lock the extended position of the bars by securely tightening the (2)
wingnuts. Be sure both wingnuts are tight.
5. Repeat for the 2nd set of bars.
Note: When determining the location of the module, be sure the
module will clear any obstructions that may be inside the cabinet
and enough clearance (height) is provided for all module devices.
Figure 2
Install bars into cart
2
0191559R1 Page 4 of 9
1. Attach each slide bracket to the bottom of the tray with (2) #8 x
3/8”PHSM screws. Figure 3.
2. Install (2) #8 x 1” PHSM screws into the back of the module-this will
prevent the module from being removed.
Attach slide brackets to tray
3
Figure 3
Shallow Tray
Tray
(2) #8 x 3/8”PHSM
(2) #8 x 3/8”PHSM
Slide
bracket
(4) 0190174
#8 x 3/8”PHSM
(2) 042749
#8 x 1” PHSM
Slide
bracket
Bars
Bars
1. Carefully set the empty tray onto both sets of bars. Be sure the rear
channel “hooks” the rear set of bars fully. Figure 4.1.
2. Install (2) #8 x 1” PHSM screws into the back of the module-this will
prevent removal. Figure 4.2.
Bars
Bars
Tray
Figure 4.1
Install tray onto bars
4(2) 042749
#8 x 1” PHSM
(2) #8 x 1” PHSM
Cart
Figure 4.2
(2) #8 x 1” PHSM
0191559R1 Page 5 of 9
Figure 5.1
Dividers
5
X 10
2. Place dividers into universal tray slots where needed. Figure 5.2,
Figure 5.2
Figure 5.4
Bar assembly
Divider
Figure 5.5
5. Route each charge cord through a tray hole and around the divider.
Secure cord to divider using the slot. Figure 5.5.
4. To lock each divider into place, bend both tabs 90-degrees. Figure 5.4.
1. Pull dividers off bar assembly. Figure 5.1.
Figure 5.3
3. See p.6 for spacing / location suggestions. Figure 5.3.
Charge cord
Note: Dividers are designed for semi-permanent installation
and use on the universal tray. Dividers can be repositioned
by straightening the tabs, but excessive bending / re-bending
cycles can cause the tabs to break.
Divider
Robot
Sphero Minis
Cubelets
Dashes DotsDotsDots Spheros
Ozobots OzobotsSpheros
Dashes Dots
Ozobots
Dots Spheros Dashes Dots
Dash Bolt DotSphero
SPRK
CubeletOzobot
Evo
Sphero
Mini
Ozobot
Bit
0191559R1 Page 6 of 9
Robot combinations
with universal trays and divider tabs
USB charging - optional
6
Figure 6
Splitter
(2) 6-Port USB
chargers
USB
charging
cables
*Devices not included.
0191559R1 Page 7 of 9
Optional trays
(See p.8)
Sprk / Bolt /
Dot Tray
55528-UWD
Sphero Mini /
Ozobot Tray
55528-UWB
Cubelet Tray
55528-UWC
Sphero Mini /
Ozobot Tray
55528-UWB
*Devices not included.
Cubelet Tray
55528-UWC Dot robots shown here on
standard universal tray with
divider tabs installed
Universal Tray- 55528UWA
• Offers exibility-accommodates most robots
• Fits in bottom of blue plastic bin or shelf
• (2) trays included
• Divider tabs not included-see 55530 below
• 10.5”W [26.7 cm] x 7”D [17.8 cm] x .65375”H
[1.7 cm]
• Unit weight: .5 lb [.227 kg]
• Shipping weight: 1 lb (.454 kg)
Sphero Mini / Ozobot Tray - 55528UWB
• Holds 24 devices
• (2) trays included
• 10.5”W [26.7 cm] x 7”D [17.8 cm] x
.65375”H [1.7 cm]
• Unit weight: .5 lb [.227 kg]
• Shipping weight: 1 lb [.454 kg]
Cubelet Tray - 55528UWC
• Holds 24 devices
• (2) trays included
• 10.5”W [26.7 cm] x 7”D [17.8 cm] x
.65375”H [1.7 cm]
• Unit weight: .5 lb [.227 kg]
• Shipping weight: 1 lb (.454 kg)
Sprk / Bolt / Dot Tray - 55528UWD
• Holds 12 devices
• (2) trays included
• 10.5”W [26.7 cm] x 7”D [17.8 cm] x
.65375”H [1.7 cm]
• Unit weight: .5 lb [.227 kg]
• Shipping weight: 1 lb [.454 kg]
Dash Bolt DotSphero
SPRK
CubeletOzobot
Evo
Sphero
Mini
Ozobot
Bit
Cubelet
Bolt DotSphero
SPRK
Ozobot
Evo
Sphero
Mini
Ozobot
Bit
0191559R1 Page 8 of 9
Accessories
X 2
0191559R1 Page 9 of 9
© 2019 Spectrum Industries Inc., All rights reserved.
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
Device Module Bar Kit - 95011
• For mounting modules into select carts
• (2) bar assemblies included
• Shipping weight: 1 lb [.45 kg]
Divider Tabs - 55530LB
• For use with universal trays only
• Provides semi-permanent areas for robots on
the universal tray
• Provides charge cord management
• 20ga steel
• (20) divider tabs included in two bar assemblies
• Light blue powdercoat
• Unit weight: .8 oz [23g]
• Shipping weight: 16 oz [454g]
Splitter - 55531
• Allows two USB chargers to be powered from a single cord
• (1) C8 male to (2) C7 female
• Length: 12” [30 cm]
• Unit weight: 12.8 oz [362g]
• Shipping weight: 16 oz [454g]
USB charger 6-port - 55522
• For charging robots
• Mounts under tray or on shelf
• 6 USB ports (up to 2.4A per port)
• 60W, 12A max
• 5’ detachable power cord
• UL-certied
• 3.9” [99mm] x 2.8” [70mm] x 1” [26mm]
• Unit weight: 6.7 oz [190g]
• Shipping weight: 16 oz [454g]
USB charger 10-port - 55529
• For charging robots
• Mounts under tray or on shelf
• 10 USB ports (up to 2.4A per port)
• 60W, 12A max
• 5’ detachable power cord
• 4.4” [112mm] x 2.7” [68mm] x 1.1” [27mm]
• Unit weight: 7.7 oz [218g]
• Shipping weight: 16 oz [454g]
For charging only-no data
For charging only-no data
See spectrumfurniture.com for the latest
accessories and detailed warranty information.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Spectrum Industries S3 Coding Module 55527HC Guide de démarrage rapide
- Taper
- Guide de démarrage rapide
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Spectrum Industries 55526HC Guide de démarrage rapide
-
-
-
-
-
-
-