Spectrum Industries 55526HC Guide de démarrage rapide

Taper
Guide de démarrage rapide

Ce manuel convient également à

Quickstart Guide
Guide de démarrage rapide
Guía de inicio rápido
S2 Coding Module
55526H0 - No power
55526HC - w/ USB power
Important
Before using this product:
Read this manual
Comply with all safety and operating instructions
Ensure all parts and correct quantities are included
Important
Avant d’utiliser ce produit:
Veillez à lire ce guide
Respectez les consignes de sécurité et d’utilisation
Vériez que vous disposez de toutes les pièces
nécessaires à l’installation
Importante
Antes de utilizar este producto:
Lea este manual
Cumpla con todas las instrucciones de prevención de
accidentes y operativas
Revise que todas las partes y las cantidades correctas
estén incluidas
Any parts damaged during shipment must be reported within 5
days of receipt. To report information regarding missing parts or
damage, to purchase parts or accessories, or if you have any
questions, please contact us.
Thank you for purchasing Spectrum products!
Les pièces endommagées pendant le transport doivent faire
l’objet d’un rapport dans les 5 jours de leur réception. Veuillez
prendre contact avec nous si des pièces manquent ou sont
abîmées, si vous avez des questions, ou encore pour acheter
des pièces ou des accessoires.
Merci pour votre achat d’un produit Spectrum!
Si alguna parte se dañó durante el embarque, deberá reportarla
en un lapso de 5 días a partir de la recepción. Para reportar
cualquier información sobre partes faltantes o dañadas, para
adquirirlas o comprar accesorios, o bien, si tiene alguna duda,
póngase en contacto con nosotros.
¡Gracias por adquirir productos Spectrum!
??
Owner’s Manual
Le manuel du propriétaire
El manual del propietario
Video
Vidéo
Vídeo
Specs
Spécications
Especicaciones
800-235-1262
http://www.spectrumfurniture.com
0191556R1 Page 1 of 8
Owner’s Manual
Le manuel du propriétaire
El manual del propietario
Video
Vidéo
Vídeo
Specs
Spécications
Especicaciones
800-235-1262
0191556R1 Page 2 of 8
(2) 042749
#8 x 1” PHSM
Hardware
(2) 0147973
Divider tabs
(2) 0147925
Universal panel
(1) 0147901
Tray
55526HC w/ USB power includes:
(2) 0145039
Bar support B-side
(with slots)
(4) 056284
8-32 Wing nut
(2) 0142528
Bar support
(with threaded
weld studs)
(1) 0191567
Splitter
(2) 0191496
6-Port USB chargers
Assemble bar supports
1. The bars should be assembled with the tabs facing away from
each other as shown in Figure 1.
2. Loosen the (2) wingnuts slightly.
3. Repeat for the 2nd set of bars.
1
X 2
Bar support B-side
(with slots)
Bar support
(with threaded weld studs)
8-32 Wing nut
(2 per assembly)
Tab
Tab
Figure 1
Components
Left slotted
uprights
Right slotted
uprights
Front bar Assembly
Rear bar Assembly
1. Carefully set the empty tray onto both sets of bars. Be sure the rear
channel “hooks” the rear set of bars fully. Figure 3.1.
2. Install (2) #8 x 1” PHSM screws into the back of the module-this will
prevent removal. Figure 3.2.
Bars
Bars
Tray
Figure 3.1
Install tray onto bars
3(2) 042749
#8 x 1” PHSM
(2) #8 x 1” PHSM
Cart
Figure 3.2
(2) #8 x 1” PHSM
0191556R1 Page 3 of 8
1. Determine the approximate location (height) you would like the
module to be mounted. The rear bar is (1) slot higher than the front.
2. Insert one tab into a slot in the left slotted upright. Figure 2.
3. Insert the opposite tab into the corresponding right slotted upright
and fully extend the bar assembly into place.
4. Lock the extended position of the bars by securely tightening the (2)
wingnuts. Be sure both wingnuts are tight.
5. Repeat for the 2nd set of bars.
Note: When determining the location of the module, be sure the
module will clear any obstructions that may be inside the cabinet
and enough clearance (height) is provided for all module devices.
Figure 2
Install bars into cart
2
0191556R1 Page 4 of 8
Figure 4.1
Dividers
4
X 10
2. Place dividers into universal tray slots where needed. Figure 4.2,
Figure 4.2
Figure 4.4
Bar assembly
Divider
Figure 4.5
5. Route each charge cord through a tray hole and around the divider.
Secure cord to divider using the slot. Figure 4.5.
4. To lock each divider into place, bend both tabs 90-degrees. Figure 4.4.
1. Pull dividers off bar assembly. Figure 4.1.
Figure 4.3
3. See p.6 for spacing / location suggestions. Figure 4.3.
Charge cord
Note: Dividers are designed for semi-permanent installation
and use on the universal tray. Dividers can be repositioned
by straightening the tabs, but excessive bending / re-bending
cycles can cause the tabs to break.
Divider
Robot
Dash Bolt DotSphero
SPRK
CubeletOzobot
Evo
Sphero
Mini
Ozobot
Bit
0191556R1 Page 5 of 8
Robot combinations
with universal trays and divider tabs
*Devices not included.
Dashes DotsDotsDots Spheros Dashes Dots
Ozobots
Sphero Minis
Cubelets
Ozobots OzobotsSpheros
Dots Spheros Dashes Dots
0191556R1 Page 6 of 8
Optional trays
(See p.7)
Sprk / Bolt /
Dot Tray
55528-UWD
Cubelet Tray
55528-UWC
Sphero Mini /
Ozobot Tray
55528-UWB
*Devices not included.
USB charging - optional
5
Figure 5
Splitter
(2) 6-Port USB
chargers
USB
charging
cables
S2 tray
Universal Tray- 55528UWA
Offers exibility-accommodates most robots
Fits in bottom of blue plastic bin or shelf
(2) trays included
Divider tabs not included-see 55530 below
10.5”W [26.7 cm] x 7”D [17.8 cm] x .65375”H
[1.7 cm]
Unit weight: .5 lb [.227 kg]
Shipping weight: 1 lb (.454 kg)
Sphero Mini / Ozobot Tray - 55528UWB
Holds 24 devices
(2) trays included
10.5”W [26.7 cm] x 7”D [17.8 cm] x
.65375”H [1.7 cm]
Unit weight: .5 lb [.227 kg]
Shipping weight: 1 lb [.454 kg]
Cubelet Tray - 55528UWC
Holds 24 devices
(2) trays included
10.5”W [26.7 cm] x 7”D [17.8 cm] x
.65375”H [1.7 cm]
Unit weight: .5 lb [.227 kg]
Shipping weight: 1 lb (.454 kg)
Sprk / Bolt / Dot Tray - 55528UWD
Holds 12 devices
(2) trays included
10.5”W [26.7 cm] x 7”D [17.8 cm] x
.65375”H [1.7 cm]
Unit weight: .5 lb [.227 kg]
Shipping weight: 1 lb [.454 kg]
Dash Bolt DotSphero
SPRK
CubeletOzobot
Evo
Sphero
Mini
Ozobot
Bit
Cubelet
Bolt DotSphero
SPRK
Ozobot
Evo
Sphero
Mini
Ozobot
Bit
0191556R1 Page 7 of 8
Accessories
X 2
0191556R1 Page 8 of 8
© 2019 Spectrum Industries Inc., All rights reserved.
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
Device Module Bar Kit - 95011
For mounting modules into select carts
(2) bar assemblies included
Shipping weight: 1 lb [.45 kg]
Divider Tabs - 55530LB
For use with universal trays only
Provides semi-permanent areas for robots on
the universal tray
Provides charge cord management
20ga steel
(20) divider tabs included in two bar assemblies
Light blue powdercoat
Unit weight: .8 oz [23g]
Shipping weight: 16 oz [454g]
Splitter - 55531
Allows two USB chargers to be powered from a single cord
(1) C8 male to (2) C7 female
Length: 12” [30 cm]
Unit weight: 12.8 oz [362g]
Shipping weight: 16 oz [454g]
USB charger 6-port - 55522
For charging robots
Mounts under tray or on shelf
6 USB ports (up to 2.4A per port)
60W, 12A max
5’ detachable power cord
UL-certied
3.9” [99mm] x 2.8” [70mm] x 1” [26mm]
Unit weight: 6.7 oz [190g]
Shipping weight: 16 oz [454g]
USB charger 10-port - 55529
For charging robots
Mounts under tray or on shelf
10 USB ports (up to 2.4A per port)
60W, 12A max
5’ detachable power cord
4.4” [112mm] x 2.7” [68mm] x 1.1” [27mm]
Unit weight: 7.7 oz [218g]
Shipping weight: 16 oz [454g]
For charging only-no data
For charging only-no data
See spectrumfurniture.com for the latest
accessories and detailed warranty information.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Spectrum Industries 55526HC Guide de démarrage rapide

Taper
Guide de démarrage rapide
Ce manuel convient également à

dans d''autres langues