SUNDRAX SPDD-1-2D4D Manuel utilisateur

SPDD-1-2D4D
Marque
SUNDRAX
Modèle
SPDD-1-2D4D
Catégorie
Stroboscopes
Taper
Manuel utilisateur
User
Manual
Version 1.04
March 11, 2020
SPDD-1-2D4D
Splitter DIN DUO
Contents
Specifications
Safe operation
General information
Advantages
Connection types
LED indication
Connection scheme
Technical maintenance
Notes
3
3
3
3
4
4
5
6
6
2Splitter DIN DUO Double input DMX splitter / repeater
3
Double input DMX splitter / repeater Splitter DIN DUO
Specifications
Supported protocols
DMX input ports
DMX output ports
DMX connectors
Mounting
Setup
Power supply
Operating Temperature:
IP Rating
Dimensions, mm
DMX512, RDM, Modbus
1 or 2 isolated
4 or 5 isolated
15EDGVC terminal blocks
DIN rail in the power cabinet
DIP switcher
~90-250 VAC, 50/60 Hz or 9-36VDC
-40°С... +70°С
IP 20
142 x 105 x 75
General information
Splitter DIN DUO is special DIN rail mount device with 6 DMX input/output ports that operates
as a regular splitter with 1 input and 5 outputs as well as two separated 1-to-2 splitters.
All input and output channels have full galvanic isolation from each other. Remote Device
Management (RDM) compatible.
The device is suitable for indoor use. Splitter is powered by 100-250 V industrial AC mains, power
consumption is less than 5 watts.
Advantages
Supports bidirectional communication (DMX512 and RDM)
Single or dual input modes
Full galvanic isolation on all ports
Safe operation
In installation, operation, preventive maintenance and
repairs of the device, the requirements of the safety rules
must be followed.
To ensure safe and reliable operation of the devices, please
observe the following requirements:
Use the device only for its intended purpose
Do not use devices that shows signs of malfunctioning
Avoid strong physical impacts on the device
Protect devices and cables from contact with corrosive liquids
Whenever a fault is detected in the device, please contact the manufacturer.
Warning!
The device uses hazardous
voltage AC 90-250V
4Splitter DIN DUO Double input DMX splitter / repeater
Connection types
Before mounting and power up, it is necessary to verify protective earthing and cable connectors.
1. Ensure the device has no damage due to transportation
2. Attach the device to the DIN rail
3. Set position of DIP-switcher 1 in accordance with needed device configuration (single-channel
or dual-channel mode)
4. All input and output channels have 120 Ohm terminators, managed by special DIP-switches
TIN, T(1)–T(5). To connect the terminator to the line is necessary to set proper switcher in ON
position, to disconnect- in OFF position
5. Connect the power, input and output DMX lines to the corresponding device ports
6. When device properly connected, the LED indicator on the device is lit. Its color indicates
the presence of a valid DMX input signal: Green - present, Red - missing
7. The device is ready for use
LED indication
SW1
SW2
SW3
SW4
ON
RDM enabled
Dual splitter mode
Full transparent mode
Bus indication mode
OFF
RDM disabled
Single splitter mode
Dedicated input(s) mode
DMX512 indication mode
Green
Red
Off
DMX512 mode
Valid DMX signal
No DMX signal
Device/Section doesn’t work
Bus mode
Bus is idle
Bus is busy
Device/Section doesn’t work
5
Double input DMX splitter / repeater Splitter DIN DUO
Connection scheme
SPLITTER DIN
ON
1
ON
1
ON
1
ON
1
ON
1
ON
1
IN DMX A
IN DMX B (D mode)
OUT 3 DMX À (S mode)
OUT 2 DMX B (D mode)
OUT 5 DMX À (S mode)
OUT 1 DMX A
OUT 2 DMX A OUT 1 DMX B (D mode)
OUT 4 DMX À (S mode)
ON
1 2 3 4
6Splitter DIN DUO Double input DMX splitter / repeater
Technical maintenance
Maintenance the device, search and troubleshooting should be performed
by service personnel. The device should be free from dirt, dents, connecting
cables and wires must be intact and securely fastened.
Notes
Please send all your warranty-related questions to [email protected]
All Sundrax products are covered by a 36 months warranty.
7
Double input DMX splitter / repeater Splitter DIN DUO
Sundrax Electronics
6008, First Central 200
2 Lakeside Drive, Park Royal, London
NW10 7FQ United Kingdom
+ 44 (0) 208 991 33 19
[email protected]
www.sundrax.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

SUNDRAX SPDD-1-2D4D Manuel utilisateur

SPDD-1-2D4D
Marque
SUNDRAX
Modèle
SPDD-1-2D4D
Catégorie
Stroboscopes
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents