Heaven Fresh HF 380 Manuel utilisateur

HF 380 AIR PURIFIER

INSTRUCTION MANUAL

HEAVEN FRESH

AC 110~120V/50~60Hz. (North America)

AC 220~240V/50~60Hz. (Europe and Asia)

Over voltage may cause fire hazard or

electric shock.

This instruction booklet describes the safety precautions to be observed during operation to

prevent injuries to yourself, other persons and damage to the device. The content not only is

suitable for this product but also suitable for electrical appliances in general.

Ensure that all safety precautions are followed when using electrical appliances for the proper

operation of the device.

power

an anthorized

personnel

shocks and fire hazards.

To prevent fire or electric shock hazard,do not

place the unit in wet places where water may

enter the device.

Do not use fabrics or other materials to cover this

device. Obstructed air inlets and outlets will

result in abnormal operation of this device that

may lead to fire or other accidents.

To prevent interference and distortion, the device

should be placed at least 1 meter away from the

computer, television or radio.

For safety reasons and to prevent fire or electric

shock, unplug the power cord from the electric

outlet socket under the following conditions:

When you do not use the device for a

long period.

When cleaning, servicing the machine or

during replacement of filter materials.

When you move the device.

casing

electric

To prevent electric shock,do not dismantle,

repair or modify this product freely.

Maintenance and cleaning shall be

processed as exactly as what instructed

in this manual.In case of malfunction,please

contact the authorized maintenance center.

ambient 104 ˚F (40° C))

SPECIAL ATTENTION

[ ]

2

COMPONENTS

Front View

[ ]

Control Panel

Odour Sensor

Receiver port

Air Outlet

Air Inlets

Dust Sensor

Bottom Stand

CLEAN METAL GRID

REPLACE FILTER

RESET

CLEAN METAL GRID

REPLACE FILTER

RESET

Heaven Fresh HF 3802

Thank you for purchasing the efcient Heaven Fresh HF 380 Air Purier. We wish you many

years of healthy indoor air with this innovative product.

[ ]

2

COMPONENTS

Front View

[ ]

Control Panel

Odour Sensor

Receiver port

Air Outlet

Air Inlets

Dust Sensor

Bottom Stand

CLEAN METAL GRID

REPLACE FILTER

RESET

CLEAN METAL GRID

REPLACE FILTER

RESET

Heaven Fresh HF 3803

Plasma Dust Collector (Metal grid)

[ Back View ]

[ Interior View ]

COMPONENTS

BEFORE USING

odour

of the sensor

But the

Follow these steps to optimize accuracy of clean air sensors:

Heaven Fresh HF 3804

Plasma Dust Collector (Metal grid)

[ Back View ]

[ Interior View ]

COMPONENTS

BEFORE USING

odour

of the sensor

But the

Follow these steps to optimize accuracy of clean air sensors:

BEFORE USING

odour

of the sensor

But the

Follow these steps to optimize accuracy of clean air sensors:

1. Run the unit for a couple hours or more.

2. During this time, also increase ventilation in the room as much as possible,

even opening a window if the air outside is at least fairly clean.

3. Unplug the HF 380, then immediately plug it in, turn it on, and resume

operation.

Unplugging the HF 380, then plugging it in again resets the clean air sensor’s

memory. By rst ensuring the air is as clean as possible, and then immediately

resetting, the sensor will be more accurate once you resume normal operation.

Heaven Fresh HF 3805

Odour

odour odour odour

odour,

EXPLANATION OF INDICATORS

OPERATING INSTRUCTIONS

(1 ft) from

Timer

duration

to turn off

Heaven Fresh HF 3806

Odour

odour odour odour

odour,

EXPLANATION OF INDICATORS

OPERATING INSTRUCTIONS

(1 ft) from

Timer

duration

to turn off

Heaven Fresh HF 3807

CLEANING AND MAINTENANCE

During cleaning and maintenance, please turn off and disconnect the plug from the power outlet.

is

Assemble the

Removing

Removing Removing

please ensure that the filter is installed

correctly with the

Push the plasama dust collector towards the base of the device.

Use your foot or knee if needed to hold the base in place.

Push the two tabs inward and lift up the dust collector.Hold the top of the

unit (where the control panel is) down to help pull out the collector grid.

Place

Disassembling the device

from

R

Remove UV lamp before cleaning

Use a slightly damp cloth to wipe & clean

& avoid scratching the coating

on the cover.

8

11

with running

Plasma Dust Collector

CLEANING AND MAINTENANCE

Heaven Fresh HF 3808

CLEANING AND MAINTENANCE

During cleaning and maintenance, please turn off and disconnect the plug from the power outlet.

is

Assemble the

Removing

Removing Removing

please ensure that the filter is installed

correctly with the

Push the plasama dust collector towards the base of the device.

Use your foot or knee if needed to hold the base in place.

Push the two tabs inward and lift up the dust collector.Hold the top of the

unit (where the control panel is) down to help pull out the collector grid.

Place

Disassembling the device

from

R

Remove UV lamp before cleaning

Use a slightly damp cloth to wipe & clean

& avoid scratching the coating

on the cover.

8

11

with running

Plasma Dust Collector

CLEANING AND MAINTENANCE

Heaven Fresh HF 3809

C

making sound

Remove

2. Lift up the tab at the top of the plastic

housing for the metal dust collector gird.

Once this tab is open,remove the dust

collector. Please wear protective gloves

to avoid any cuts on your fingers.

CLEAN METAL GRID

REPLACE FILTER

RESET

CLEANING AND MAINTENANCE

8

If the dirt is hard to remove, pre-soak in diluted detergent and

then use a toothbrush to clean.

removed or discarded

this would result in

cause rusting

ensure that the unit is completely dry

if you want to purchase

use warm water

Please beware not to damage any wiring while cleaning the dust collector.

CLEANING AND MAINTENANCE

CAUTION

Please keep in mind that electrical wires of the Plasma Dust Collector Plate are

fragile and special care is required while cleaning.

Heaven Fresh HF 38010

C

making sound

Remove

2. Lift up the tab at the top of the plastic

housing for the metal dust collector gird.

Once this tab is open,remove the dust

collector. Please wear protective gloves

to avoid any cuts on your fingers.

CLEAN METAL GRID

REPLACE FILTER

RESET

CLEANING AND MAINTENANCE

8

If the dirt is hard to remove, pre-soak in diluted detergent and

then use a toothbrush to clean.

removed or discarded

this would result in

cause rusting

ensure that the unit is completely dry

if you want to purchase

use warm water

Please beware not to damage any wiring while cleaning the dust collector.

CLEANING AND MAINTENANCE

Heaven Fresh HF 38011

Remove

the the not functioning,

Carefully replace with

Resetting

1.CLEAN METAL GRID Indicator

2.REPLACE FILTER Indicator

CLEAN METAL GRID indicator

REPLACE FILTER Indicator

8

10

After cleaning and replacing filters, reset the CLEAN METAL GRID and REPLACE FILTER indicators.

Otherwise the two indicators would remaining glowing after turning on the unit.

While resetting, the unit should remain plugged into the socket, but the uint itself should be turned off.

The RESET button is inside the unit (cannot be reached with finger).

Please use a toothpick or other sharp object to push the RESET button.

Replacing the UV lamp

CLEAN METAL GRID

REPLACE FILTER

RESET

CLEAN METAL GRID

REPLACE FILTER

RESET

CLEAN METAL GRID

REPLACE FILTER

RESET

CLEANING AND MAINTENANCE

Take out

Put back the sensor correctly after cleaning,

make sure that the cord is reconnected in the

correct direction.

CLEANING AND MAINTENANCE

Heaven Fresh HF 38012

Take out

Put back the sensor correctly after cleaning,

make sure that the cord is reconnected in the

correct direction.

CLEANING AND MAINTENANCE

Heaven Fresh HF 38013

Clean Air Monitor

Q. Why does only one LED light glow under "Clean Air Monitor"?

A. First, the air may have been clean the whole time. Or, the air purifier may be positioned

where the sensor is too far away from the airborne pollutants and irritants. If this is the

case, relocate the unit where it is close to the source of indoor air pollution. To test the

sensor, stir dust or increase pollution near the sensor. If the level of pollution goes up

when this is done, then the sensor is operating properly.

Q. Why is there always two LED lights glowing under "Clean Air Monitor"?

A. There are multiple possibilities for this. One possibility is that polluted air from outside

the room is being circulated into the room with the unit. Another possibility is that a

constant amount of pollution is being created within the room, such as from smoking. It

is also important to note that it can take some time to clean the room to the point where

only one LED light is on, indicating the air around the unit is purified.

Q. Why does the "Clean Air Monitor" function keep switching back and forth?

A. The Irritant Sensor can be affected by a cell phone or other wireless equipment. Keep

cell phones and other wireless equipment away from the unit.

Q. Why does the Dust and Irritant Sensor keep blinking?

A. The top of the sensor has accumulated too much dust, and needs to be cleaned. Please

refer to page 13 of this manual for instructions on cleaning the sensor.

Q. Why doesn't the Odour Sensor work?

A. The sensor memory needs to be reset. Refer to page 5 under Before Using. When first

purchased or when the unit has been unplugged for over a week, the sensor will not be

as sensitive. After 1 to 2 days of operation, the sensor will regain its sensitivity.

Odour Sensor

Filter

is

Q. Why is the filter not getting rid of dust and odour effectively?

Have the front and back of the filter been mistakenly reversed?

FREQUENTLY ASKED QUESTIONS

Heaven Fresh HF 38014