pro.point 9029893 Le manuel du propriétaire
- Catégorie
- Coupe-bordures
- Taper
- Le manuel du propriétaire
V1.0 9029893
Please read and understand all instructions before use. Retain this manual for future reference.
EXTENDED
AIR DIE GRINDER.
9029893 1/4 in. Extended Air Die Grinder V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Air Inlet (in.) 1/4
Pressure Range (PSI)
90
Air Consumption @ 90 PSI (CFM) 4
Average CFM @ 15 Second Run Time (CFM) 4
CFM @ Full Load (CFM) 11
Speed Rating (RPM) 20,000
Collet Size (in.)
1/4
Arbor Size (in.)
Min. Hose Size (in.) 3/8
Overall Length (in.)
10.2
Material Steel/aluminum/plastic
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual.
A notice is an alert that there is a possibility of property damage, injury
or death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that
will result in severe personal injury or death if the proper
precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice
that could result in severe personal injury or death if the
proper precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that
may result in minor or moderate injury if proper practices are
not taken.
NOTICE! This notice indicates that a specific hazard or unsafe
practice will result in equipment or property damage, but
not personal injury.
V1.0 1/4 in. Extended Air Die Grinder 9029893
Visit www.princessauto.com for more information 3
INTRODUCTION
This extended air die grinder is ideal for cutting, porting, deburring and
grinding in hard-to-reach spaces. It features steel, aluminum and
plastic construction.
SAFETY
WARNING! Read and understand all instructions before using this
tool. The operator must follow basic precautions to reduce the
risk of personal injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or
inspection and maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean,
well-lit and free of distractions. Place lights so you are not working
in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away
from the work area.
3. Store tools properly in a safe and dry location. Keep tools out of
the reach of children.
4. Do not install or use in the presence of flammable gases, dust
or liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the
Canadian Standards Association (CSA) or American National
Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side
protection for the eyes. Eye protection equipment should comply
with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of
work performed.
2. Wear gloves that provide protection based on the work materials or
to reduce the effects of tool vibration.
3. Wear protective clothing designed for the work environment
and tool.
9029893 1/4 in. Extended Air Die Grinder V1.0
4 For technical questions call 1-800-665-8685
4. Non-skid footwear is recommended to maintain footing and
balance in the work environment.
5. Wear a NIOSH approved respirator when working on materials that
produce hazardous fumes, dust or particulate matter.
6. The tool may contain high pressure. Use safety glasses and gloves
for protection during operation. Keep hands clear of the exposed
rubber portions of the hose.
7. The air source used with this tool may cause hearing damage.
Wear hearing protection gear with an appropriate Noise Reduction
Rating to withstand the decibel levels.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to the tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with
the moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating the tool. Proper footing and
balance enables better control in unexpected situations.
4. Keep your fingers away from the trigger/switch while carrying the
tool, attaching an air hose or an accessory. Lock the trigger/switch
safety if available.
5. Never point the air stream or tool at any point of your body, other
people or animals. Debris and dust ejected at high speed can
cause an injury.
6. Serious injury or death may occur from inhaling compressed air.
The air stream may contain carbon monoxide, toxic vapors or solid
particles. Never inhale compressed air directly from the pump or
air tool.
AIR TOOL PRECAUTIONS
1. Use only clean and dry compressed air as a power source.
Contaminated or moist air will gradually damage the tool.
2. Install an in-line shutoff valve or regulator to allow immediate control
over the air supply in an emergency, even if a hose is ruptured.
V1.0 1/4 in. Extended Air Die Grinder 9029893
Visit www.princessauto.com for more information 5
3. Discontinue tool use if it does not work properly or air is leaking.
Tag or mark the tool as ‘defective’ or ‘out of service’ until repaired.
4. Check the manufacturer’s maximum pressure rating for air tools
and accessories. Compressor outlet pressure must be regulated to
never exceed the maximum pressure rating of the tool (see
Specifications). Exceeding the maximum PSI rating can create a
bursting hazard, causing injury and property damage.
5. Attach all accessories properly to the tool before connecting the air
supply. A loose accessory may detach or break during operation.
6. Never use oxygen, combustible gas or any other bottled gas as a
power source. Any power source other than an air compressor
could cause an explosion and serious personal injury.
7. Turn OFF the valve and discharge any remaining air pressure after
each use or before adjusting the tool.
8. Do not leave the air tool unattended with its compressed air supply
on. Turn off the compressed air supply and bleed the air tool of any
remaining compressed air before leaving the air tool unattended.
9. Serious injury may occur from loose debris being propelled at high
speeds from the compressed air stream. Always wear OSHA
approved safety glasses to protect the eyes during operation of the
air co mp res sor.
10. Always turn off the air compressor and drain tank pressure
completely before attempting maintenance or attaching air tools.
Release pressure slowly from the system.
AIR HOSE PRECAUTIONS
1. Inspect the tool's air hose for cracks, fraying or other faults before
each use. Discontinue use if the air hose is damaged or hissing is
heard from the air hose or couplers. Replace the defective air hose.
2. Do not allow people, mobile equipment or vehicles to pass over the
unprotected air hose. Position the air hose away from high traffic
areas, in a reinforced conduit or place planks on both sides of the
air hose to create a protective trench.
3. Prevent damage to the air hose by observing the following:
a. Never carry the tool by the air hose.
b. Keep the air hose behind the tool and out of the tool's work path.
9029893 1/4 in. Extended Air Die Grinder V1.0
6 For technical questions call 1-800-665-8685
c. Keep the air hose away from heat, oil, sharp edges or
moving parts.
d. Do not wrap the air hose around the tool as sharp edges may
pierce or crack the air hose. Gently coil the hose and either
hang on a hook or fasten with a device to keep hose together
when storing.
4. A damaged or disconnected air hose under pressure may whip
around and inflict personal injury or damage the work area. Secure
the compressor's air hose to a fixed or permanent structure with
clamps or cable ties.
COMPRESSOR/TANK PRECAUTIONS
DANGER! Do not use an air tank beyond its expiration date. A
tank rupture or explosion may kill or cause a serious injury to
yourself or a bystander. Disable and discard the air tank
according to the your municipality by-laws.
1. Never drill into, weld, patch or modify the air tank. Immediately
replace the tank or compressor if an air leak develops. The leak
may lead to a rupture.
2. Never make adjustments to the components that control tank
pressure. Serious injury or death may occur if modifications are
made to the pressure switch, safety relief valve or other
components that control the tank pressure.
3. Check operation of the pressure relief valve on a regular basis and
never operate without a factory approved pressure relief valve. Do
not make alterations to the factory operating pressure settings.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to the tool safety rules.
If you use this tool unsafely or incorrectly, you can suffer serious
personal injury.
WARNING! Some surfaces contain materials which can be toxic.
When working on materials that may contain lead, asbestos,
copper chromium arsenate or other toxic materials, extra care
should be taken to avoid inhalation and minimize skin contact.
V1.0 1/4 in. Extended Air Die Grinder 9029893
Visit www.princessauto.com for more information 7
1. Use the correct tool for the job. This tool was designed for a
specific function. Do not modify or alter this tool or use it for an
unintended purpose.
2. Do not use the tool if any parts are damaged, broken or misplaced.
Repair or replace the parts.
3. Do not use any power tool with a malfunctioning power switch or
control. A power tool that fails to respond to the controls is
dangerous and can cause an injury. A qualified technician must
repair and verify the power tool is operating correctly, before it can
be used.
4. Do not cover the air vents. Proper cooling is necessary prevent
damage to the tool’s motor.
5. Avoid unintentional starts. Ensure the switch is off when connecting
to the power source.
6. Disconnect the power source before installing or servicing the tool.
7. Remove adjusting keys and wrenches before using the tool. The
tool may eject an attached wrench or a key and cause an injury to
you or a bystander.
8. Never point the tool towards yourself. It could inflict an injury.
9. Never force the tool. Excessive pressure could break the tool,
resulting in damage to your workpiece or serious personal injury.
Excessive pressure is the cause if your tool runs smoothly under no
load, but roughly under load.
10. Keep hands and fingers away from the work area. Any part of the
body contacting the tool’s working parts could result in an injury.
11. Only use accessories that are specifically designed for use with the
tool. Ensure the accessory is tightly installed.
12. Never touch the tool accessory or workpiece during or immediately
after use. They may be hot and could inflict a burn injury.
13. Take work breaks to prevent the tool's motor from overheating
and/or overloading.
14. The tool can develop high pressure. Use safety glasses and gloves
for protection during operation. Keep hands clear of the exposed
rubber portions of the hose.
9029893 1/4 in. Extended Air Die Grinder V1.0
8 For technical questions call 1-800-665-8685
15. Do not exceed the maximum 90 PSI rating (see Specifications).
16. Only use a grinding attachment that is equal to or exceeds the
maximum RPM of the tool (see Specifications).
17. Only use a grinding attachment with the correct arbor size and
shape that matches the grinder’s spindle.
18. Ensure the grinding attachment does not have wear or chipping.
Replace if necessary.
19. Before using the tool on the workpiece, run the tool at the highest
speed, without a load, for at least 30 seconds in a safe position. Stop
immediately if there is any vibration or wobbling that could indicate
poor installation or a poorly balanced grinding attachment. Check the
tool to determine the cause.
20. Sparks may be created when working with the die grinder. Hold the
tool so that sparks fly away from you and other persons or
flammable materials. Keep up-to-date fire-prevention safety
instructions in the event of a fire.
21. Do not use a coolant or water with this die g rinder.
22. Do not use as a fixed grinder.
VIBRATION PRECAUTIONS
1. This tool vibrates during use. Repeated or long-term exposure to
vibration may cause temporary or permanent physical injury. Take
frequent breaks when using the tool.
2. If you feel any medical symptoms related to vibrations (such as
tingling, numbness, and white or blue fingers), seek medical
attention as soon as possible.
3. Wear suitable gloves to reduce the effects of vibration.
4. DO NOT use this tool before consulting a physician if one of the
following applies:
a. Pregnant
b. Impaired blood circulation
to the hands
c. Past hand injuries
d. Nervous system
disorders
e. Diabetes
f. Raynaud's Disease
V1.0 9029893
Please read and understand all instructions before use. Retain this manual for future reference.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace
the missing part before operating. Failure to do so could result in
a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect
for damage. Make sure that all items in the parts list are included.
ASSEMBLY & INSTALLATION
INSTALL AIR COUPLER PLUG
Prepare a standard 1/4 in. NPT coupler plug (sold separately) for use
with your tool.
1. Wrap the external threads of the coupler plug with sealant tape.
a. Wrap tape in a clockwise direction so it will not unravel.
b. Do not tape all the threads. Leave several leading threads
unwrapped for easier alignment.
2. Screw the coupler plug into the tool's air inlet and tighten with a
wrench until snug.
3. Run the compressor at a low volume and check the connection for
air leaks. Do not use the tool until all air leaks are repaired or the
faulty component is replaced.
IMPORTANT! Vibration may cause failure if a quick coupler is
connected directly to the air tool. To overcome this, connect a
leader hose to the tool. A quick coupler may then be used to
connect the leader hose to the air line hose.
INSTALL GRINDING ATTACHMENT
1. Select the appropriate grinding attachment for the task.
2. Push the spanner in the collet shaft.
3. Insert the mandrel into the collet chuck a minimum of 1/4 in. deep
to prevent the attachment from disengaging from the grinder while
in use.
4. Tighten the collet chuck securely with the spanner.
9029893 1/4 in. Extended Air Die Grinder V1.0
10 For technical questions call 1-800-665-8685
CAUTION! Always check the grinding attachment for tightness
before each use. A loose attachment can be thrown from the tool
with considerable force, causing injury.
OPERATION
1. Connect the tool to the air hose.
2. Place the grinding attachment over the work piece and turn on the
air die grinder.
IMPORTANT! Use grinding wheels when working with hard
materials and rotary files for milling soft materials such as
nonferrous metals (aluminum, brass, copper, etc.) Using grinding
wheels when working with soft materials will clog the wheel,
preventing it from cutting as it was designed.
NOTICE! Do not allow the tool to run with no load for an extended
period of time as this will shorten its life.
PRESSURE DROP
Apply the air consumption and pressure rate numbers to the tool’s air
inlet, not the compressor’s outlet. Calculate the pressure drop for your
air supply set-up and increase the compressor outlet pressure to
compensate. Make sure you do not exceed the maximum pressure for
any part of your air supply system.
Installing a pressure gauge at the tool inlet is the best way to measure
the air pressure and adjust the compressor’s output.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient,
easier to control and will have fewer problems.
2. Inspect the tool fittings, alignment, hoses and power supply cord
periodically. Have damaged or worn components repaired or replaced
by an authorized technician. Only use identical replacement parts
when servicing.
3. Follow instructions for lubricating and changing accessories.
4. Only use accessories intended for use with this tool.
5. Keep the tool clean, dry and free from oil/grease at all times.
V1.0 1/4 in. Extended Air Die Grinder 9029893
Visit www.princessauto.com for more information 11
6. Maintain the tool’s labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd. for
replacements.
WARNING! Only qualified service personnel should repair the
tool. An improperly repaired tool may present a hazard to the
user and/or others.
AIR TOOL LUBRICATION
NOTICE! Only use air tool oil to lubricate the tool. Other
lubricants are not suitable and will damage the tool or cause a
malfunction during use.
NOTICE! Never use a penetrating oil to lubricate an air tool.
Penetrating oil acts as a solvent that will dissolve the tool’s
grease packing and may damage the o-rings, causing the tool to
seize or malfunction.
1. All air tools have an internal coating of grease to prevent corrosion
during shipping and storage. Remove this grease by adding a
generous amount of air tool oil in the air inlet and then run the tool
under no load until the exhaust is clear.
2. Manually add a drop or two of air tool oil into the tool’s coupler
plug before each use and after every hour of continuous use. The
tool will not work properly without lubrication and parts will
wear prematurely.
3. Avoid adding too much air tool oil as this can cause premature
power loss and eventual tool failure. A qualified technician will need
to take the tool apart and clean out the excess oil.
4. Apply a generous amount of air tool oil to the tool before storing it
for an extended period of time (overnight, weekend, etc.). Run the
tool for approximately 30 seconds to ensure the oil is evenly
distributed throughout the tool. Store it in a clean and dry location.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
9029893 1/4 in. Extended Air Die Grinder V1.0
12 For technical questions call 1-800-665-8685
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not
function properly or parts are missing. If unable to do so, have a
qualified technician service the tool.
PROBLEM(S) POSSIBLE CAUSE(S) SUGGESTED SOLUTION(S)
Tool runs at
normal speed,
but loses power
under load.
Motor parts worn. 1. Have a qualified technician
service the tool.
2. Replace tool or parts.
Tool runs slowly.
Air flows slightly
from exhaust.
Motor parts jammed with
dirt particles.
OR
Airflow blocked by dirt.
1. Check air inlet filter for
blockage.
2. Pour air tool lubricating oil
into air inlet as per
lubrication instructions for
clearing shipping grease.
3. Operate tool in short bursts
to clear debris.
4. If tool still jammed, clean
tool and lubricate per
lubrication instructions.
Tool runs slowly.
Air flows slightly
from exhaust.
1. Air regulator in closed
position.
2. Damage or excessive
wearing of internal
parts.
1. Open the air regulator to
desired airflow.
2a. Have a qualified
technician service the
tool.
2b. Replace tool or parts.
Tools will not
run. Air flows
freely from
exhaust.
Damage or excessive
wearing of internal parts.
1. Have a qualified technician
service the tool.
2. Replace tool or parts.
Tool will not shut
off.
1. Throttle valve O-ring
dislodged from inlet
valve seat.
2. Trigger mechanism
jammed or dirty.
1. Replace throttle valve
O-rings.
2. Clean trigger mechanism
and lubricate.
Loss of power or
erratic
performance.
1. Excessive drain on the
air hose. Incorrect size
or type of hose
connectors.
1. Check the air hose and
confirm the hose fitting is
correct for the inlet bushing.
V1.0 1/4 in. Extended Air Die Grinder 9029893
Visit www.princessauto.com for more information 13
2. Moisture or restriction
in the air hose/tank
3. Air compressor has
insufficient flow.
2. Depressurize system and
drain tank and air hose of
water.
3. Ensure tool is connected to
a compressor with a rate
flow that matches the tool.
PARTS BREAKDOWN
PARTS LIST
# DESCRIPTION QTY PART ID
1 Collet Nut 1 214-001
2 Collet 1 214-002
3
Spindle
1
214-003
4 Spacer 1 214-004
5 Bearing 2 214-005
6
Washer
1
214-006
7 Shaft Coupling 1 214-007
8
Retaining Bar
1
214-008
9029893 1/4 in. Extended Air Die Grinder V1.0
14 For technical questions call 1-800-665-8685
9 Ball Bearing 1 214-009
10
Front End Plate
1
214-010
11 Spring Pin 3 214-011
12
Rotor
1
214-012
13 Rotor Blade 4 214-013
14 Cylinder 1 214-014
15
Rear End Plate
1
214-015
16 Bearing 1 214-016
17 Housing 1 214-017
18
Valve Screw
1
214-018
19 O-Ring 1 214-019
20
Valve Spring
1
214-020
21
Throttle Valve
1
214-021
22 O-Ring 1 214-022
23
Pin
1
214-023
24 Throttle Lever Assembly 1 214-024
25 Spring Pin 1 214-025
26
Spring Pin
1
214-026
27 Exhaust Sleeve 1 214-027
28 Inlet Bushing 1 214-028
29
#11 Spanner
1
214-029
30 #17 Spanner 1 214-030
V1,0 9029893
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce
manuel afin de pouvoir le consulter plus tard.
MEULE À RECTIFIER
LES MATRICES
PNEUMATIQUE.
DÉPLOYÉE
9029893 Meule à rectifier les m atrices pneumatique déployée, 1/4 po V1,0
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Entrée d’air (po) 1/4
Plage de pression (lb/po carré)
90
Consommation d’air à 90 lb/po carré (pi
cubes/min)
4
Débit moyen à un temps de fonctionnement
de 15 secondes (pi cubes/min)
4
Débit à pleine charge (pi cubes/min) 11
Vitesse nominale (tr/min)
20 000
Capacité de collet (po) 1/4
Taille d’arbre (po)
Diamètre min. de tuyau (po)
3/8
Longueur hors tout (po) 10,2
Matériau Acier/aluminium/plastique
DÉFINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans
ce manuel. Un avis est une alerte indiquant qu'il existe un risque de
dommage à la propriété, de blessure ou de décès si on ne respecte pas
certaines instructions.
DANGER ! Cet avis indique un risque immédiat et particulier qui
entraînera des blessures corporelles graves ou
même la mort si on omet de prendre les précautions
nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique
non sécuritaire qui pourrait entraîner des blessures
corporelles graves ou même la mort si on omet de
prendre les précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement
dangereuse qui peut entraîner des blessures
mineures ou modérées si on ne procède pas de la
façon recommandée.
V1,0 Meule à rectifier les matrices pneumatique déployée, 1/4 po 9029893
Visitez www.princessauto.com pour plus d'i nformations 3
AVIS ! Cet avis indique un risque particulier ou une pratique
non sécuritaire qui entraînera des dommages au
niveau de l'équipement ou des biens, mais non des
blessures corporelles.
INTRODUCTION
Cette meule à rectifier les matrices pneumatique rallongée est idéale
pour la coupe, le perçage, l’ébavurage et le meulage dans les espaces
difficiles d’accès. Se caractérise par une construction en acier, en
aluminium et en plastique.
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les
instructions avant d'utiliser cet outil. L'utilisateur doit respecter
les précautions de base lorsqu'il utilise cet outil afin de réduire
le risque de blessure ou de dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection
et d'entretien.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez
votre aire de travail propre, bien éclairée et exempte de toute
distraction. Placez les lampes de façon à ne pas travailler
dans l’ombre.
2. Assurez-vous que les personnes qui ne portent pas l'équipement de
sécurité approprié ne se trouvent pas à proximité de l'aire de travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec.
Gardez les outils hors de la portée des enfants.
4. N'installez pas et n'utilisez pas d'outils électriques en présence de
gaz, de poussière ou de liquides inflammables.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection personnelle
homologué par l'Association canadienne de normalisation (CSA) ou
l'American National Standards Institute (ANSI).
9029893 Meule à rectifier les m atrices pneumatique déployée, 1/4 po V1,0
4 En cas de questions techniques, appelez le 1-800-665-8685
ÉQUIPEMENT DE PROTECTION PERSONNELLE
1. Portez toujours des lunettes antiprojections qui offrent une
protection frontale et latérale pour les yeux. L'équipement de
protection des yeux devrait être conforme à la norme CSA Z94.3-
07 ou ANSI Z87.1 fonction du type de travail effectué.
2. Portez des gants qui protègent en fonction des matériaux de travail
et pour réduire les effets des vibrations de l'outil.
3. Portez des vêtements de protection conçus pour l'environnement
de travail et pour l'outil.
4. Les chaussures antidérapantes sont recommandées pour maintenir
la stabilité et l'équilibre au sein de l'environnement de travail.
5. Portez un appareil respiratoire approuvé par la NIOSH pour
travailler sur des matériaux qui produisent des émanations
dangereuses, de la poussière ou des particules.
6. L’outil peut être à haute pression. Portez des lunettes de sécurité et
des gants pour vous protéger au cours de l'opération. Gardez les
mains à l'écart des parties de caoutchouc exposées du tuyau.
7. L’outil peut être à haute pression. Portez un dispositif de protection
anti-bruit présentant une cote de réduction du bruit adéquate en
fonction du niveau de décibels.
PRÉCAUTIONS PERSONNELLES
Gardez le contrôle de l'outil, de vos mouvements et de l'environnement
de travail pour éviter les blessures ou le bris de l'outil.
1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,
d'alcool ou de médicaments.
2. Évitez de porter des vêtements ou des bijoux pouvant se prendre
dans les pièces mobiles d'un outil. Gardez les cheveux longs
recouverts ou attachés.
3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en
servir. Une stabilité et un équilibre appropriés sont nécessaires afin
d'avoir un meilleur contrôle en cas de situations inattendues.
4. Gardez vos doigts à bonne distance de la gâchette/commutateur
lors du transport de l’outil ou du branchement d’un tuyau à air ou
d’un accessoire. Engagez le verrou de gâchette/interrupteur, le
cas échéant.
V1,0 Meule à rectifier les matrices pneumatique déployée, 1/4 po 9029893
Visitez www.princessauto.com pour plus d'i nformations 5
5. Ne dirigez jamais le jet d’air ou les outils vers votre corps, d’autres
individus ou des animaux. Les débris et la poussière projetés à
grande vitesse peuvent causer des blessures.
6. Des blessures graves ou même la mort peuvent survenir en cas
d’inhalation de l’air comprimé. Le jet d’air peut contenir du
monoxyde de carbone, des vapeurs toxiques ou des particules
solides. N’inhalez jamais l’air comprimé provenant directement de
la pompe ou d’un outil pneumatique.
PRÉCAUTIONS RELATIVES AUX
OUTILS PNEUMATIQUES
1. Utilisez uniquement un air comprimé propre et sec comme source
d’énergie. L’air contaminé ou humide endommagera
progressivement l’outil.
2. Installez une soupape d'arrêt ou un régulateur sur la conduite afin
de permettre une commande immédiate de l'alimentation en air, en
cas d'urgence, même si un tuyau se fend.
3. Arrêtez d’utiliser l’outil s’il ne fonctionne pas correctement ou s’il
présente des fuites d’air. Attachez une étiquette sur l’outil indiquant
qu’il est « défectueux » ou qu’il est « hors service », jusqu’à ce qu’il
soit réparé.
4. Consultez la pression nominale maximale du fabricant en ce qui
concerne les outils pneumatiques et accessoires. La pression de
sortie du compresseur doit être réglée de façon à ne jamais
dépasser la pression nominale maximale de l'outil (consultez
Spécifications). Si on dépasse la pression nominale maximale, il
pourrait en résulter un risque d’explosion capable d’entraîner des
blessures et des dommages aux biens.
5. Avant de relier l’alimentation en air, fixez correctement tous les
accessoires sur l’outil. Un accessoire mal attaché pourrait se
détacher et se briser durant l’utilisation.
6. N'utilisez jamais d'oxygène, de gaz combustible ou tout autre gaz
embouteillé en tant que source d'énergie. Une source d'énergie
autre qu'un compresseur d'air pourrait causer une explosion
entraînant ainsi des blessures corporelles graves.
7. Fermez la soupape et évacuez toute la pression d’air restante
après chaque utilisation ou avant d’ajuster l’outil.
9029893 Meule à rectifier les m atrices pneumatique déployée, 1/4 po V1,0
6 En cas de questions techniques, appelez le 1-800-665-8685
8. Ne laissez pas l’outil d'air sans surveillance alors que la source
d'air comprimé est en fonction. Fermez la source d'air comprimé et
purgez l’outil d'air de tout air comprimé restant avant de laisser
celui-ci sans surveillance.
9. Des blessures graves peuvent se produire si des débris sont
propulsés à haute vitesse dans le jet d’air du compresseur. Portez
toujours des lunettes de sécurité approuvés OSHA afin de vous
protéger les yeux lorsque vous utilisez le compresseur d’air.
10. Arrêtez toujours le compresseur d’air et évacuez complètement la
pression du réservoir avant de tenter de procéder à l’entretien ou
de fixer des outils pneumatiques. Évacuez doucement la pression
du système.
PRÉCAUTIONS RELATIVES AUX TUYAUX À AIR
1. Inspectez le tuyau d’air de l'outil pour déceler des fissures, des
effilochures et tout autre défaut avant chaque utilisation. Arrêtez
l'utilisation si le tuyau d’air est endommagée ou si un sifflement se
fait entendre provenant du tuyau à air. Remplacez le tuyau d’air ou
le composant défectueux.
2. Veillez à ce que personne, ni aucun matériel mobile ou des
véhicules n'écrasent le tuyau d’air non protégée. Placez le tuyau
d’air à l'écart des zones de circulation intense, soit à l'intérieur d'un
conduit renforcé ou placez des planches des deux côtés de le
tuyau d’air afin de créer un couloir protecteur.
3. Pour éviter tout dommage au tuyau d'air, observez les
précautions suivantes :
a. Ne transportez jamais l'outil par le tuyau d'air.
b. Gardez le tuyau d’air derrière l'outil et hors du trajet de l'outil.
c. Gardez le tuyau d’air à l'écart des sources de chaleur, de
l'huile, des bords coupants ou des pièces mobiles.
d. N'enroulez pas le tuyau d’air autour de l'outil, car les arêtes
vives risquent de percer ou de fissurer le tuyau d'air. Enroulez
délicatement le tuyau et suspendez-le à un crochet ou
attachez-le sur un support pour qu’il reste enroulé pendant
son rangement.
4. Un conduite d'air endommagée ou débranchée sous pression peut
se comporter à la façon d'un fouet et infliger des blessures
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
pro.point 9029893 Le manuel du propriétaire
- Catégorie
- Coupe-bordures
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: pro.point 9029893 Owner's manual
Autres documents
-
PROPOINT 8844037 Le manuel du propriétaire
-
-
Power Fist 8844102 Le manuel du propriétaire
-
-
-
-