PROPOINT 8844243 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 8844243

Catégorie: Coupe-bordures

Taper: Le manuel du propriétaire

V1.0 8844243

Please read and understand all instructions before use. Retain this manual for future reference.

DIE GRINDER



LOW-NOISE AIR

8844243 Low-Noise Air Die Grinder V1.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Max. Pressure 90 PSI

Air Consumption @ 90 PSI 3.1 CFM

CFM @ Full Load 10 CFM

No Load Speed 22,000 RPM

Collet Size 1/4 in.

Air Inlet 1/4 in.

Min. Hose Size 3/8 in.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual.

A notice is an alert that there is a possibility of property damage, injury

or death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard

that will result in severe personal injury or death if the

proper precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe

practice that could result in severe personal injury or

death if the proper precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation

that may result in minor or moderate injury if proper

practices are not taken.

NOTICE! This notice indicates that a specific hazard or unsafe

practice will result in equipment or property damage,

but not personal injury.

V1.0 Low-Noise Air Die Grinder 8844243

Visit www.princessauto.com for more information 3

INTRODUCTION

The Low-Noise Air Die Grinder is ideal for a wide variety of cutting,

cylinder porting, weld breaking, deburring, polishing and grinding tasks.

SAFETY

WARNING! Read and understand all instructions before using this

tool. The operator must follow basic precautions to reduce the

risk of personal injury and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or

inspection and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean,

well-lit and free of distractions. Place lights so you are not working

in a shadow.

2. Keep anyone not wearing the appropriate safety equipment away

from the work area.

3. Store unused tools properly in a safe and dry location to prevent rust

or damage. Lock tools away and keep out of the reach of children.

4. Do not install or use in the presence of flammable gases, dust or

liquids.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the

Canadian Standards Association (CSA) or American National

Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side

protection for the eyes. Eye protection equipment should comply

with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of

work performed.

2. Wear the appropriate type of full-face shield in addition to safety

googles, as the work can create chips, abrasive or particulate matter.

3. Wear gloves that provide protection based on the work materials or

to reduce the effects of tool vibration.

8844243 Low-Noise Air Die Grinder V1.0

4 For technical questions call 1-800-665-8685

3.1 Do not wear gloves when operating a tool that can snag the

material and pull the hand into the tool.

4. Wear protective clothing designed for the work environment and tool.

5. Non-skid footwear is recommended to maintain footing and

balance in the work environment.

6. Wear steel toe footwear or steel toe caps to prevent a foot injury

from falling objects.

7. Wear the appropriate rated dust mask or respirator.

8. This tool can cause hearing damage. Wear hearing protection gear

with an appropriate Noise Reduction Rating to withstand the

decibel levels.

9. The tool may contain high pressure. Use safety glasses and gloves

for protection during operation. Keep hands clear of the exposed

rubber portions of the hose.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with

the moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and

balance enables better control in unexpected situations.

4. Support the workpiece or clamp it to a stable platform. Holding the

workpiece by hand or against your body may lead to personal injury.

5. Keep your fingers away from the trigger/switch while carrying the

tool, attaching an air hose or an accessory. Lock the trigger/switch

safety if available.

6. Avoid unintentional starts. Be sure that the regulator/throttle switch

is in the neutral or OFF position when not in use and before

connecting it to any air source.

7. Serious injury or death may occur from inhaling compressed air. The air

stream may contain carbon monoxide, toxic vapors or solid particles.

Never inhale compressed air directly from the pump or air tool.

V1.0 Low-Noise Air Die Grinder 8844243

Visit www.princessauto.com for more information 5

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to the tool safety

rules. If you use this tool unsafely or incorrectly, you can suffer

serious personal injury.

1. Use the correct tool for the job. This tool was designed for a

specific function. Do not modify or alter this tool or use it for an

unintended purpose.

2. Do not use the tool if any parts are damage broken or misplaced.

Repair or replace the parts.

3. This tool will not stop moving immediately. Do not lay the tool down

or leave it unattended until it has come to a complete stop. A part

that is moving could make the tool jump or grab a surface and pull

the tool out of your control.

4. Always make sure the work surface is free from nails and other

foreign objects.

5. After changing the accessories or making adjustments, make sure

the collet nut and any other adjustment devices are securely

tightened. Loose adjustment devices will be violently thrown.

6. Always check accessories for damage before each use. Damaged

accessories can break during use and cause serious injury.

7. If you are interrupted when operating the die grinder, complete the

process and switch off the tool before looking up.

8. Use metal and voltage detectors to locate hidden electric, water or

gas lines. Avoid touching live components or conductors.

9. Only use die grinder attachments with this tool. Do not use drill bits.

AIR TOOL PRECAUTIONS

1. Use only clean and dry compressed air as a power source.

Contaminated or moist air will gradually damage the tool.

2. Install an in-line shutoff valve or regulator to allow immediate control

over the air supply in an emergency, even if a hose is ruptured.

3. Discontinue tool use if it does not work properly or air is leaking.

Tag or mark the tool as ‘defective’ or ‘out of service’ until repaired.

8844243 Low-Noise Air Die Grinder V1.0

6 For technical questions call 1-800-665-8685

4. Check the manufacturer’s maximum pressure rating for air tools

and accessories. Compressor outlet pressure must be regulated to

never exceed the maximum pressure rating of the tool (see

Specifications). Exceeding the maximum PSI rating can create a

bursting hazard, causing injury and property damage.

5. Attach all accessories properly to the tool before connecting the air

supply. A loose accessory may detach or break during operation.

6. Never use oxygen, combustible gas or any other bottled gas as a

power source. Any power source other than an air compressor

could cause an explosion and serious personal injury.

7. Turn OFF the valve and discharge any remaining air pressure after

each use or before adjusting the tool.

8. Do not leave the air tool unattended with its compressed air supply

on. Turn off the compressed air supply and bleed the air tool of any

remaining compressed air before leaving the air tool unattended.

9. Serious injury may occur from loose debris being propelled at high

speeds from the compressed air stream. Always wear OSHA

approved safety glasses to protect the eyes during operation of the

air compressor.

10. Never point the air stream or tools at any point of your body, other

people or animals. Debris and dust may be ejected without

warning. Always turn off the air compressor and drain tank

pressure completely before attempting maintenance or attaching air

tools. Release pressure slowly from the system.

AIR HOSE PRECAUTIONS

1. Inspect the tool's air hose for cracks, fraying or other faults before

each use. Discontinue use if the air hose is damaged or hissing is

heard from the air hose or couplers. Replace the defective air hose.

2. Do not allow people, mobile equipment or vehicles to pass over the

unprotected air hose. Position the air hose away from high traffic

areas, in a reinforced conduit or place planks on both sides of the

air hose to create a protective trench.

3. Prevent damage to the air hose by observing the following:

3.1 Never carry the tool by the air hose.

3.2 Keep the air hose behind the tool and out of the tool's work path.

3.3 Keep the air hose away from heat, oil, sharp edges or moving parts.

V1.0 Low-Noise Air Die Grinder 8844243

Visit www.princessauto.com for more information 7

3.4 Do not wrap the air hose around the tool as sharp edges may pierce

or crack the air hose. Gently coil the hose and either hang on a

hook or fasten with a device to keep hose together when storing.

4. A damaged or disconnected air hose under pressure may whip

around and inflict personal injury or damage the work area. Secure

the compressor's air hose to a fixed or permanent structure with

clamps or cable ties.

COMPRESSOR/TANK PRECAUTIONS

DANGER! Do not use an air tank beyond its expiration date. A tank

rupture or explosion may kill or cause a serious injury to yourself

or a bystander. Disable and discard the air tank according to the

your municipality by-laws.

1. Never drill into, weld, patch or modify the air tank. Immediately

replace the tank or compressor if an air leak develops. The leak

may lead to a rupture.

2. Never make adjustments to the components that control tank

pressure. Serious injury or death may occur if modifications are

made to the pressure switch, safety relief valve or other

components that control the tank pressure.

3. Check operation of the pressure relief valve on a regular basis and

never operate without a factory approved pressure relief valve. Do

not make alterations to the factory operating pressure settings.

POWER TOOL PRECAUTIONS

Tool accessory is a general term that refers to drill bit, saw or cutting

blades, grinding wheel, etc. as appropriate for the tool.

1. Do not use any power tool with a malfunctioning power switch or

control. A power tool that fails to respond to the controls is dangerous

and can cause an injury. A qualified technician must repair and verify

the power tool is operating correctly, before it can be used.

2. Do not cover the air vents.

3. Disconnect the power source before installing or servicing the tool.

4. Never force the tool. Excessive pressure could break the tool,

resulting in damage to your workpiece or serious personal injury.

Excessive pressure is the cause if your tool runs smoothly under no

load, but roughly under load.

8844243 Low-Noise Air Die Grinder V1.0

8 For technical questions call 1-800-665-8685

5. Keep hands and fingers away from the work area. Any part of body

contacting the tool’s working parts could cause an injury.

6. Only use accessories that are specifically designed for use with the

tool. Ensure the accessory is tightly installed.

7. Never touch the tool accessory or workpiece during or immediately

after use. They may be hot and could inflict a burn injury.

8. Never use a tool with a cracked or worn tool accessory. Change

the tool accessory before using it.

GRINDING TOOL PRECAUTIONS

WARNING! Some surfaces contain materials which can be toxic.

When working on materials that may contain lead, asbestos,

copper chromium arsenate or other toxic materials, extra care

should be taken to avoid inhalation and minimize skin contact.

1. Only use a grinding die that exceeds the maximum RPM of the tool

(see Specifications).

2. Only use a grinding die with the correct shaft size and shape.

3. Ensure the grinding attachment does not have wear or chipping.

Replace if necessary.

4. Before using the tool on the workpiece, run the tool at the highest

speed, without a load, for at least 30 seconds in a safe position.

Stop immediately if there is any vibration or wobbling that could

indicate poor installation or a poorly balanced grinding attachment.

Check the tool to determine the cause.

5. Sparks may be created when working with the die grinder. Hold the

tool so that sparks fly away from you and other persons or flammable

materials. Keep up-to-date fire-prevention safety instructions in the

event of a fire.

6. Do not use a coolant or water with this die grinder.

7. Do not use as a fixed grinder.

KICKBACK PRECAUTIONS

Kickback is a sudden reaction to a pinched or snagged grinding

accessory. The tool kicks out and away from the workpiece while the

grinding accessory is still active. This can inflict a serious injury on the

user or a bystander. Kickback can also damage the tool or workpiece.

V1.0 Low-Noise Air Die Grinder 8844243

Visit www.princessauto.com for more information 9

Kickback can be avoided by taking proper precautions:

1. Maintain a firm grip on the tool and position your body and arms to

allow you to resist a kickback. Kickback will propel the tool in the

direction opposite to the grinding accessory’s direction of rotation. A

snagged grinding die may pull the tool out of the grasp of the user.

2. If kickback occurs, the accessory may:

2.1 pass over a body part, causing a seriously injury;

2.2 wrench the user’s arm causing muscle or joint injuries; and

2.3 strike bystanders.

3. Use clamps or a vice to hold down smaller workpieces.

4. Use special care when working on corners, sharp edges or flexible

material. These workpieces have a tendency to snag the grinding

accessory.

5. Only use grinding accessories designed for the tool.

6. Support large panels to minimize the risk of pinching the grinding

accessory. Large panels may sag under their own weight.

VIBRATION PRECAUTIONS

1. This tool vibrates during use. Repeated or long-term exposure to

vibration may cause temporary or permanent physical injury. Take

frequent breaks when using the tool.

2. If you feel any medical symptoms related to vibrations (such as

tingling, numbness, and white or blue fingers), seek medical

attention as soon as possible.

3. Wear suitable gloves to reduce the effects of vibration.

4. DO NOT use this tool before consulting a physician if one of the

following applies:

a. Pregnant

b. Impaired blood circulation

to the hands

c. Past hand injuries

d. Nervous system disorders

e. Diabetes

f. Raynaud's Disease

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace

the missing part before operating. Failure to do so could result in

a malfunction and personal injury.

8844243 Low-Noise Air Die Grinder V1.0

10 For technical questions call 1-800-665-8685

Remove the parts and accessories from the packaging and inspect for

damage. Make sure that all items in the contents are included.

Contents: • Air Die Grinder • 19 mm Wrench

• 14 mm Wrench • Male Plug

IDENTIFICATION KEY

A Collet

B Collet Nut

C Spindle

D Trigger Lever

E Trigger Lever Safety

F Air Regulator

G Air Inlet

ASSEMBLY & INSTALLATION

Numbered references in parenthesis (#1) refer to the included Parts List.

Letter references in parenthesis (A) refer to the included Identification Key

INSTALL AIR COUPLER

Prepare a standard 1/4 in. NPT male air coupler (sold separately) for

use with your tool.

1. Wrap the external threads of the male coupler with sealant tape.

1.1 Wrap tape in a clockwise direction so it will not unravel.

1.2 Do not tape all the threads. Leave several leading threads

unwrapped for easier alignment.

2. Screw the coupler into the tool's air inlet and tighten with a wrench

until snug.

3. Run the compressor at a low volume and check the connection for

air leaks. Do not use the tool until all air leaks are repaired or the

faulty component is replaced.

IMPORTANT! Vibration may cause failure if a quick coupler is

connected directly to the air tool. To overcome this, connect a

leader hose to the tool. A quick coupler may then be used to

connect the leader hose to the air line hose.

V1.0 Low-Noise Air Die Grinder 8844243

Visit www.princessauto.com for more information 11

INSTALL THE GRINDING DIE

1. Insert the 14 mm wrench (#25) onto the spindle (#22) flats to

prevent it from moving.

2. Insert the 19 mm wrench (#26) over the collet nut (#24) flats.

3. Turn the 19 mm wrench clockwise to loosen the collet nut while

holding the 14 mm spanner in place.

4. Loosen the collet nut, but do not remove. This allows the collet’s

arms to spread apart.

4.1 Remove the collet nut if replacing the collet (#23) as well.

5. Insert the grinder die shaft into the collet. Make sure it is fully seated.

6. Hand-tighten the collet nut, then finish tightening with the wrenches.

OPERATION

1. Clean the die grinder of packing grease before first use. Also grease

the spindle gears. See the Air Tool Lubrication section for instructions.

2. Install the grinding die (See Assembly & Installation). The type of

grinding die installed will depend on the material and task.

3. Connect the tool to the air source.

4. Set the compressor to the correct air pressure and flow (see

Specifications). Start the compressor.

5. Push the trigger lever safety (D) forward to free the trigger lever (E).

6. Rotate the air regulator (F) wheel to adjust the grinder’s speed.

7. Wait until the grinding die has reach full speed before applying it to

the material

8. Test the tool under no load to confirm the grinding die is installed

correctly.

9. Apply the grinding die against the material so the debris is moved

away from the work area. Do not press down too hard, as this can

cause the die to slow or gouge the workpiece.

10. Lift the die grinder from the material and slowly release the trigger

lever. The trigger lever safety will automatically snap back into place.

11. Wait for the grinding die to stop before placing the tool down.

12. Shut the compressor off once the task is completed. Squeeze the

trigger to release residual compressed air from the hose and tool.

Disconnect the tool.

8844243 Low-Noise Air Die Grinder V1.0

12 For technical questions call 1-800-665-8685

DIES AND ATTACHMENTS

Die grinder dies and attachments are designed to cut, polish and shape

surfaces. Some attachments can be used on any material while others

are designed specifically for wood, plastic or metal. Consult the

manufacturer’s information to determine the correct use of the die or

attachment.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient,

easier to control and will have fewer problems.

2. Inspect the tool fittings, alignment, hoses and power supply cord

periodically. Have damaged or worn components repaired or

replaced by an authorized technician. Only use identical

replacement parts when servicing.

3. Verify the die grinder’s speed with a tachometer to ensure it does

not exceed the maximum speed. Have the tool repaired if the max.

speed is higher than the no load speed in Specifications.

4. Follow instructions for lubricating and changing accessories.

5. Only use accessories intended for use with this tool.

6. Keep the tool handles clean, dry and free from oil/grease at all times.

7. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

8. Keep the vent passages clear of accumulated dirt, dust, and oil.

9. Clean the tool after each use.

WARNING! Only qualified service personnel should repair the

tool. An improperly repaired tool may present a hazard to the

user and/or others.

V1.0 Low-Noise Air Die Grinder 8844243

Visit www.princessauto.com for more information 13

AIR TOOL LUBRICATION

NOTICE! Only use air tool oil to lubricate the tool. Other lubricants

are not suitable and will damage the tool or cause a malfunction

during use.

NOTICE! Never use a penetrating oil to lubricate an air tool.

Penetrating oil acts as a solvent that will dissolve the tool’s

grease packing and may damage the o-rings, causing the tool to

seize or malfunction.

1. All air tools have an internal coating of grease to prevent corrosion

during shipping and storage. Remove this grease by adding a

generous amount of air tool oil in the air inlet and then run the tool

under no load until the exhaust is clear.

2. Manually add a drop or two of air tool oil into the tool’s male

coupler before each use and after every hour of continuous use.

The tool will not work properly without lubrication and parts will

wear prematurely.

3. Avoid adding too much air tool oil as this can cause premature

power loss and eventual tool failure. A qualified technician will need

to take the tool apart and clean out the excess oil.

4. Apply a generous amount of air tool oil to the tool before storing it

for an extended period of time (overnight, weekend, etc.). Run the

tool for approximately 30 seconds to ensure the oil is evenly

distributed throughout the tool. Store it in a clean and dry location.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws

for electronic devices, batteries, oil or other toxic liquids.

IMPORTANT! DO NOT pollute the environment by allowing

uncontrolled discharge of waste oil.

8844243 Low-Noise Air Die Grinder V1.0

14 For technical questions call 1-800-665-8685

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not

function properly or parts are missing. If unable to do so, have a

qualified technician service the tool.

PROBLEM(S) POSSIBLE CAUSE(S) SUGGESTED SOLUTION(S)

Tool runs at normal

speed, but loses

power under load.

Motor parts worn. 1. Have a qualified technician

service the tool.

2. Replace tool or parts.

Tool runs slowly. Air

flows slightly from

exhaust.

Motor parts jammed

with dirt particles.

Airflow blocked by dirt.

1. Check air inlet filter for

blockage.

2. Pour air tool lubricating oil

into air inlet as per lubrication

instructions for clearing

shipping grease.

3. Operate tool in short bursts to

clear debris.

4. If tool still jammed, clean tool

and lubricate per lubrication

instructions.

Tool runs slowly. Air

flows slightly from

exhaust.

Air regulator in closed

position.

Open the air regulator to desired

airflow.

Tools will not run. Air

flows freely from

exhaust.

Damage or excessive

wearing of internal

parts.

1. Have a qualified technician

service the tool.

2. Replace tool or parts.

Tool will not shut off.

1. Throttle valve o-ring

dislodged from seat

inlet valve.

2. Trigger mechanism

jammed or dirty.

1. Replace throttle valve

o-rings.

2. Clean trigger mechanism and

lubricate.

Loss of power or

erratic performance.

1. Excessive drain on

the air hose.

Incorrect size or type

of hose couplers.

2. Moisture or

restriction in the air

hose/tank

3. Air compressor has

insufficient flow.

1. Check the air hose and

confirm the hose fitting is

correct for the inlet bushing.

2. Depressurize system and

drain tank and air hose of

water.

3. Ensure tool is connected to a

compressor with a rate flow

that matches the tool.

V1.0 Low-Noise Air Die Grinder 8844243

Visit www.princessauto.com for more information 15

PARTS BREAKDOWN

PARTS LIST

# DESCRIPTION QTY

1 Regulator Set 1

2 Snap Ring 1

3 Valve Stem Set 1

4 Air Inlet 1

5 Exhaust Sleeve Set 1

6 Cone Muffler 1

Valve Set

8 Spring Pin 1

Lever

10 Protecting Rubber 1

11 Housing 1

12 Bearing (696Zz) 1

13 Rear Plate 1

14 Rotor Blade 4

15 Rotor 1

16 Cylinder Set 1

17 Bearing Spacer 1

18 Front Plate 1

Bearing (608Zz)

20 Washer 1

Clamp Nut

22 Spindle 1

23 Collet 1

24 Collet Nut 1

25 Wrench, 14 mm 1

26 Wrench, 19 mm 1

8844243 Low-Noise Air Die Grinder V1.0

16 For technical questions call 1-800-665-8685

V1,0 8844243

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce

manuel afin de pouvoir le consulter plus tard.



PEU BRUYANTE

8844243 Meule à rectifier les matrices pneumatique peu bruyante V1,0

2 En cas de questions techniques, appelez le 1-800-665-8685

SPÉCIFICATIONS

Pression max 90 lb/po carré

Consommation d'air à 90 lb/po carré 3,1 pi cubes/min

Débit à pleine charge 10 pi cubes/min

Vitesse à vide

22 000 tr/min

Taille de Pince de serrage 1/4 po

Vitesse nominale

1/4 po

Diamètre min. de tuyau 3/8 po

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont présentés

dans ce manuel. Un avis est une alerte indiquant qu'il existe un risque

de dommage à la propriété, de blessure ou de décès si on ne respecte

pas certaines instructions.

DANGER ! Cet avis indique un risque immédiat et particulier

qui entraînera des blessures corporelles

graves ou même la mort si on omet de prendre

les précautions nécessaires.

AVERTISSEMENT ! Cet avis indique un risque particulier ou une

pratique non sécuritaire qui pourrait entraîner

des blessures corporelles graves ou même la

mort si on omet de prendre les précautions

nécessaires.

ATTENTION ! Cet avis indique une situation possiblement

dangereuse qui peut entraîner des blessures

mineures ou modérées si on ne procède pas de

la façon recommandée.

AVIS ! Cet avis indique un risque particulier ou une

pratique non sécuritaire qui entraînera des

dommages au niveau de l'équipement ou des

biens, mais non des blessures corporelles.

V 1,0 Meule à rectifier les matrices pneumatique peu bruyante 8844243

Visitez www.princessauto.com pour plus d'informations 3

INTRODUCTION

La meule à rectifier les matrices pneumatique peu bruyante est idéale

pour une grande variété de travaux de découpage, de perçage de

cylindre, de rupture de joints de soudure, d’ébavurage et d’opérations

de polissage et de meulage.

SÉCURITÉ

AVERTISSEMENT ! Veuillez lire et comprendre toutes les

instructions avant d'utiliser cet outil. L'utilisateur doit respecter

les précautions de base lorsqu'il utilise cet outil afin de réduire

le risque de blessure ou de dommage à l'équipement.

Conservez ce manuel qui contient les avertissements de sécurité, les

précautions, les instructions de fonctionnement ou d'inspection et

d'entretien.

AIRE DE TRAVAIL

1. Travaillez dans un environnement de travail sécuritaire. Gardez votre

aire de travail propre, bien éclairée et exempte de toute distraction.

Placez les lampes de façon à ne pas travailler dans l’ombre.

2. Assurez-vous que les personnes qui ne portent pas l'équipement de

sécurité approprié ne se trouvent pas à proximité de l'aire de travail.

3. Rangez les outils correctement dans un lieu sécurisé et sec.

Gardez les outils hors de la portée des enfants.

4. N'installez pas et n'utilisez pas d'outils électriques en présence de

gaz, de poussière ou de liquides inflammables.

SÉCURITÉ PERSONNELLE

AVERTISSEMENT ! Portez de l'équipement de protection personnelle

homologué par l'Association canadienne de normalisation (CSA) ou

l'American National Standards Institute (ANSI).

ÉQUIPEMENT DE PROTECTION PERSONNELLE

1. Portez toujours des lunettes antiprojections qui offrent une

protection frontale et latérale pour les yeux. L'équipement de

protection des yeux devrait être conforme à la norme CSA Z94.3-

07 ou ANSI Z87.1 fonction du type de travail effectué.

8844243 Meule à rectifier les matrices pneumatique peu bruyante V1,0

4 En cas de questions techniques, appelez le 1-800-665-8685

2. Portez un écran facial panoramique de type approprié avec les

lunettes de sécurité puisque cette tâche peut créer des copeaux,

des matières abrasives ou des particules.

3. Portez des gants qui protègent en fonction des matériaux de travail

et pour réduire les effets des vibrations de l'outil.

3.1 Ne portez pas de gants lorsque vous utilisez un outil dans lequel

le tissu pourrait demeurer coincé, entraînant ainsi la main.

4. Portez des vêtements de protection conçus pour l'environnement

de travail et pour l'outil.

5. Les chaussures antidérapantes sont recommandées pour maintenir

la stabilité et l'équilibre au sein de l'environnement de travail.

6. Portez des chaussures à embout d'acier ou à coquilles d'acier pour

éviter les blessures aux pieds dues à la chute d'objets.

7. Portez un masque antipoussières ou un appareil respiratoire

nominal approprié.

8. Cet outil peut causer des dommages à l'ouïe. Portez un dispositif

de protection anti-bruit présentant une cote de réduction du bruit

adéquate en fonction du niveau de décibels.

9. L’outil peut être à haute pression. Portez des lunettes de sécurité et

des gants pour vous protéger au cours de l'opération. Gardez les

mains à l'écart des parties de caoutchouc exposées du tuyau.

PRÉCAUTIONS PERSONNELLES

Gardez le contrôle de l'outil, de vos mouvements et de l'environnement

de travail pour éviter les blessures ou le bris de l'outil.

1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,

d'alcool ou de médicaments.

2. Évitez de porter des vêtements ou des bijoux pouvant se prendre

dans les pièces mobiles d'un outil. Gardez les cheveux longs

recouverts ou attachés.

3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en

servir. Une stabilité et un équilibre appropriés sont nécessaires afin

d'avoir un meilleur contrôle en cas de situations inattendues.

4. Soutenez la pièce à travailler ou fixez-la sur une plate-forme stable.

Une pièce à travailler tenue dans les mains ou appuyée contre

La page charge ...

PROPOINT 8844243 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 8844243

Catégorie: Coupe-bordures

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: PROPOINT 8844243 Owner's manual

PROPOINT 8844243 Le manuel du propriétaire

PROPOINT 8844243 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents