PROPOINT 9082694 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 9082694

Taper: Le manuel du propriétaire

V1.0 9082694

Please read and understand all instructions before use. Retain this manual for future reference.



9082694 8 in. Belt Grinder Attachment V1.0

2 For technical questions call 1-800-665-8685

Horsepower

Adaptive motor: 1/2 or 3/4 HP

Belt Size

48 x 2 in.

Wheel/Pad Size

7 in.

No Load Speed

Belt: 862 RPM

Disc: 3,600 RPM

Arbor Size

5/8 in.

Overall Size

22-3/8L x 4-5/8W x 7-3/4H in.

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or

death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may

result in minor or moderate injury if proper practices are not

taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice

will result in equipment or property damage, but not

personal injury.

V1.0 8 in. Belt Grinder Attachment 9082694

Visit www.princessauto.com for more information 3

This attachment fits most popular brands of grinders that have screw-on

wheel guards. It’s easy to install with no special adapter required, includes

1 sanding belt and 1 sanding disc, and it has the capability to remove

material up to 5 times faster than with an equivalent grit grinding wheel.

WARNING! Read and understand all instructions

before using this tool. The operator must follow

basic precautions to reduce the risk of personal

injury and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection

and maintenance instructions.

1. Operate in a safe work environment. Keep your work area clean, well-

lit and free of distractions. Place lights so you are not working in a

shadow.

2. Keep anyone not wearing the appropriate safety equipment away

from the work area.

3. Store tools properly in a safe and dry location. Keep tools out of the

reach of children.

4. Do not install or use in the presence of flammable gases, dust or

liquids.

WARNING! Wear personal protective equipment

approved by the Canadian Standards Association

(CSA) or American National Standards Institute

(ANSI).

1. Always wear impact safety goggles that provide front and side

protection for the eyes. Eye protection equipment should comply

with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of work

performed.

9082694 8 in. Belt Grinder Attachment V1.0

4 For technical questions call 1-800-665-8685

2. Wear the appropriate type of full-face shield in addition to safety

googles, as the work can create chips, abrasive or particulate matter.

3. Wear gloves that provide protection based on the work materials or

to reduce the effects of tool vibration.

3.1 Do not wear gloves when operating a tool that can snag the

material and pull the hand into the tool.

4. Wear protective clothing designed for the work environment and

tool.

5. Non-skid footwear is recommended to maintain footing and balance

in the work environment.

6. Wear steel toe footwear or steel toe caps to prevent a foot injury

from falling objects.

7. Wear the appropriate rated dust mask or respirator.

8. This tool can cause hearing damage. Wear hearing protection gear

with appropriate Noise Reduction Rating to withstand decibel levels.

Control the tool, personal movement and the work environment to avoid

personal injury or damage to the tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating the tool. Proper footing and balance

enables better control in unexpected situations.

4. Support the workpiece or clamp it to a stable platform. Holding the

workpiece by hand or against your body may lead to personal injury.

5. Securely hold this tool using both hands. Using a tool with only one

hand can result in loss of control.

WARNING! DO NOT let comfort or familiarity with

product (gained from repeated use) replace strict

adherence to the tool safety rules. If you use this

tool unsafely or incorrectly, you can suffer serious

personal injury.

V1.0 8 in. Belt Grinder Attachment 9082694

Visit www.princessauto.com for more information 5

1. Use the correct tool for the job. This tool was designed for a specific

function. Do not modify or alter this tool or use it for an unintended

purpose.

2. Do not use the tool if any parts are damaged, broken or misplaced.

Repair or replace the parts.

3. Maintain a firm grip on the material and position your body and arms

to allow you to resist a kickback. Kickback can propel the material in

the direction of the cutting accessory’s rotation.

3.1 Use a clamp to hold the material if the tool includes a clamping

system.

4. Never use a tool with a cracked or worn grinding wheel. Change the

grinding wheel before using. Use only flanges supplied with the

grinder.

5. Before using the tool on a workpiece, test the tool by running it at the

highest no-load speed for at least 60 seconds in a safe position. Stop

immediately if there is any abnormal vibration or wobbling that could

indicate poor installation of the grinding wheel. Check the tool to

determine the cause.

6. Do not start the tool when the grinding wheel is touching the

workpiece.

7. Clean dust and debris from beneath the grinding wheels frequently.

8. Do not grind magnesium or aluminum, as a fire may result.

9. Make sure the bench grinder is on a firm, level surface and properly

secured to avoid injury from unexpected movement. Firmly clamp or

bolt the bench grinder to a support surface to prevent slipping or sliding

during the operation.

10. Do not use a grinding wheel that vibrates when used. If dressing the

wheel does not solve the vibration, replace it. Also inspect the

machine for other causes of vibration such as worn bearings or a bent

shaft. Repair or replace broken components immediately before

reusing the machine.

11. Ensure the grinding wheel has a clean edge. Check the grinding wheel

for wear or chipping and replace if necessary.

9082694 8 in. Belt Grinder Attachment V1.0

6 For technical questions call 1-800-665-8685

12. Hold the tool so that sparks fly away from you, bystanders or

flammable materials. Have a fully charged fire extinguisher present in

the event of a fire.

13. Do not subject the grinding wheel to any lateral pressure as it may

damage the tool or cause it to kickback.

1. Do not use any power tool with a malfunctioning power switch or

control. A power tool that fails to respond to the controls is

dangerous and can cause an injury. A qualified technician must repair

and verify the power tool is operating correctly, before it can be used.

2. Ensure the power supply matches the tool’s motor voltage (see

Specifications).

3. Do not cover the air vents. Proper cooling is necessary prevent

damage to the tool’s motor.

4. Avoid unintentional starts. Ensure the switch is off when connecting

to the power source.

5. Disconnect the power source before installing or servicing the tool.

6. Remove adjusting keys and wrenches before using the tool. The tool

may eject an attached wrench or a key and cause an injury to you or a

bystander.

7. Never point the tool towards yourself. It could inflict an injury.

8. Never force the tool. Excessive pressure could break the tool,

resulting in damage to your workpiece or serious personal injury.

Excessive pressure is the cause if your tool runs smoothly under no

load, but roughly under load.

9. Keep hands and fingers away from the work area. Any part of the body

contacting the tool’s working parts could result in an injury.

10. Take work breaks to prevent the tool's motor from overheating

and/or overloading.

WARNING! Do not operate the tool if any part is

missing. Replace the missing part before

operating. Failure to do so could result in a

malfunction and personal injury.

V1.0 8 in. Belt Grinder Attachment 9082694

Visit www.princessauto.com for more information 7

Remove the parts and accessories from the packaging and inspect for

damage.

Make sure that all items in the parts list are included.

Numbered references in parenthesis (#1) refer

to the included Parts List.

Dashed numbers in parenthesis (Fig. 1-1) refer

to a specific point in an illustration or image.

1. Assemble the protective shield (#19)

using the hex nuts (#20), flat washers

(#13) and pan-head screws (#12). Make

sure the screws are properly tightened (Fig. 1). 2

2. Once completed, it should resemble Fig. 2.

1. Remove the grinding wheel and shield, keeping the

nut (#5) and wheel flange (#6) in a safe location for

future applications (Fig. 3).

2. Put the locating sleeve jig (#44) on the

motor shaft against the motor end cap

(Fig. 3).

3. Install the sanding belt frame onto the

motor shaft using the flat washers (#9)

and screws (#8). Ensure they are

properly tightened (Fig. 3).

4. Take the locating sleeve out and keep

for future applications.

5. Once completed, it should resemble Fig. 4.

Fig. 1

Fig. 2

Fig. 3

Fig. 4

9082694 8 in. Belt Grinder Attachment V1.0

8 For technical questions call 1-800-665-8685

1. Install the driving wheel (#7) into the

wheel shaft of the grinder (Fig. 5).

2. Install the grinding wheel flange (#6)

and tighten the nut (#5) (Fig. 5).

3. Once completed, it should resemble

Fig. 6.

1. Loosen the bolt (#36) (Fig. 7).

2. Press the front driven wheel to drop the

tension lock board and fix the driven wheel

support (#38).

2. Install the sanding belt (#1) (Fig. 8).

3. Lift the tension lock board up to tighten the

nut.

4. Turn the sanding belt by hand to check the

running track (Fig. 9-1).

5. Turn on the power to check alignment.

6. If necessary, turn off the power and adjust

the eccentric plate (#25) slightly until the

position is ideal (Fig. 7).

7. Once completed, it should resemble Fig. 10.

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

V1.0 8 in. Belt Grinder Attachment 9082694

Visit www.princessauto.com for more information 9

1. Install the sanding disc (#4) and tighten

the screws (#3) (Fig. 11).

2. Paste the sanding paper (#2) to the disc

evenly and smoothly (Fig. 11).

3. Once completed, it should resemble Fig.

12.

1. Connect the tool to its power source.

2. Allow the disc to achieve max. speed.

3. Gently contact workpiece to the sanding

paper.

4. Separate workpiece from the sanding paper.

4.1 If results are as desired, disconnect tool

form the power source.

4.2 If results are not as desired, continue operation.

1. Loosen the nut (#18) (Fig. 13).

2. Adjust the frame up and down to the

desired angle (Fig. 13).

3. Once in the ideal position, tighten

the nut.

1. Loosen the bolt (#36) (Fig. 14).

2. Press the front driven wheel to drop the

tension lock board and fix the driven

wheel support.

3. Remove the old belt.

4. Install the new belt.

5. Lift the tension lock board up to tighten

the nut.

Fig. 11

Fig. 12

Fig. 13

Fig. 14

9082694 8 in. Belt Grinder Attachment V1.0

10 For technical questions call 1-800-665-8685

1. Tear the old sanding paper off of the wheel.

2. Clean the wheel.

3. Paste the new sanding paper to the disc evenly and smoothly.

1. Maintain the tool with care. A tool in good condition is efficient,

easier to control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace damaged

or worn components. Only use identical replacement parts when

servicing.

3. Follow instructions for lubricating and changing accessories.

4. Ensure guards and other safety features are in good working

condition before each operation.

5. Keep the tool clean, dry and free from oil/grease at all times.

6. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

WARNING! Only qualified service personnel should

repair the tool. An improperly repaired tool may

present a hazard to the user and/or others.

Clean dust or other debris from the tool after each use.

Inspect and lubricate the tool when required. Only use light oil to lubricate

the tool. Other lubricants may not be suitable and could damage the tool

or cause a malfunction during use.

When not in use for an extended period, apply a thin coat of lubricant to

the steel parts to avoid rust. Remove the lubricant before using the tool

again.

NOTICE! NEVER use a penetrating oil to lubricate

the tool. Penetrating oil may act as a solvent

that will break down the grease and cause the tool

to seize up.

V1.0 8 in. Belt Grinder Attachment 9082694

Visit www.princessauto.com for more information 11

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

Visit a Princess Auto Ltd. location for a solution if the tool does not

function properly or parts are missing. If unable to do so, have a qualified

technician service the tool.

9082694 8 in. Belt Grinder Attachment V1.0

12 For technical questions call 1-800-665-8685

V1.0 8 in. Belt Grinder Attachment 9082694

Visit www.princessauto.com for more information 13

DESCRIPTION

QTY

Abrasive sanding belt

Sanding paper

Philips Screw M4x8

Sanding board

Nut

Grinding wheel flange

Driving wheel

Screw M5*20

Flat washer M5

Carriage bolts M6*12

Mounting flange

Philips pan-head screw M5*16

Flat washer M5

Hex bolt M12*20

Hex bolt M8*16

Flat washer M5

Flat washer M6

Hex nut M6

Shield

Hex nut M5

Fixing frame

Fixing oboard

Protection plate

Philips pan-head screw M6*8

Eccentric plate

Belt support board

Rivet

Clamp plate

Hex nut M6

Self-locking nut M6

Hex bolt M6*16

9082694 8 in. Belt Grinder Attachment V1.0

14 For technical questions call 1-800-665-8685

Spring housing

Spring

O-sealing ring 1.8*2

Tension lock board

Hex bolt M6*20

Hex fine-thread nut M10*1

Driven wheel support

Spacer

Driven wheel shaft

Bearing

Driven wheel

Clip ring for shaft M12

Locating sleeve

V1.0 8 in. Belt Grinder Attachment 9082694

Visit www.princessauto.com for more information 15

9082694 8 in. Belt Grinder Attachment V1.0

16 For technical questions call 1-800-665-8685

V1,0 9082694

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce

manuel afin de pouvoir le consulter plus tard.



9082694 Accessoire pour meuleuse à courroie de 8 po V1,0

2 En cas de questions techniques, appelez le 1-800-665-8685

Puissance

Moteur adaptatif : 1/2 ou 3/4 CV

Taille de courroie

48 x 2 po

Taille de meule/patin

7 po

Vitesse à vide

Courroie : 862 tr/min

Disque : 3 600 tr/min

Taille d’arbre

5/8 po

Dimensions hors tout

22 3/8 (long.) x 4 5/8 (larg.) x 7 3/4 (haut.)

Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce

manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage à

la propriété, de blessure ou de décès si on ne respecte pas certaines

instructions.

DANGER ! Cet avis indique un risque immédiat et particulier qui

entraînera des blessures corporelles graves ou même

la mort si on omet de prendre les précautions

nécessaires.

AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique

non sécuritaire qui pourrait entraîner des blessures

corporelles graves ou même la mort si on omet de

prendre les précautions nécessaires.

ATTENTION ! Cet avis indique une situation possiblement dangereuse

qui peut entraîner des blessures mineures ou modérées

si on ne procède pas de la façon recommandée.

AVIS ! Cet avis indique un risque particulier ou une pratique

non sécuritaire qui entraînera des dommages au niveau

de l'équipement ou des biens, mais non des blessures

corporelles.

V1,0 Accessoire pour meuleuse à courroie de 8 po 9082694

Visitez www.princessauto.com pour plus d'informations 3

Cet accessoire convient à la plupart des marques populaires de meuleuses

avec des protège-meule vissés. Il est facile à installer sans adaptateur

spécial, comprend 1 courroie abrasive et 1 disque abrasif, et il a la capacité

de retirer le matériau jusqu’à 5 fois plus vite qu’avec une meule à grain

équivalent.

AVERTISSEMENT ! Veuillez lire et comprendre toutes

les instructions avant d'utiliser cet outil.

L'utilisateur doit respecter les précautions de

base lorsqu'il utilise cet outil afin de réduire

le risque de blessure ou de dommage à

l'équipement.

Conservez ce manuel qui contient les avertissements de sécurité, les

précautions, les instructions de fonctionnement ou d'inspection et

d'entretien.

1. Travaillez dans un environnement de travail sécuritaire. Gardez votre

aire de travail propre, bien éclairée et exempte de toute distraction.

Placez les lampes de façon à ne pas travailler dans l’ombre.

2. Assurez-vous que les personnes qui ne portent pas l'équipement de

sécurité approprié ne se trouvent pas à proximité de l'aire de travail.

3. Rangez les outils correctement dans un lieu sécurisé et sec. Gardez

les outils hors de la portée des enfants.

4. N'installez pas et n'utilisez pas d'outils électriques en présence de

gaz, de poussière ou de liquides inflammables.

AVERTISSEMENT ! Portez de l'équipement de protection

personnelle homologué par l'Association canadienne

de normalisation (CSA) ou l'American National

Standards Institute (ANSI).

9082694 Accessoire pour meuleuse à courroie de 8 po V1,0

4 En cas de questions techniques, appelez le 1-800-665-8685

1. Portez toujours des lunettes antiprojections qui offrent une

protection frontale et latérale pour les yeux. L'équipement de

protection des yeux devrait être conforme à la norme CSA Z94.3-07

ou ANSI Z87.1 fonction du type de travail effectué.

2. Portez un écran facial panoramique de type approprié avec les

lunettes de sécurité puisque cette tâche peut créer des copeaux, des

matières abrasives ou des particules.

3. Portez des gants qui protègent en fonction des matériaux de travail et

pour réduire les effets des vibrations de l'outil.

3.1 Ne portez pas de gants lorsque vous utilisez un outil dans lequel le

tissu pourrait demeurer coincé, entraînant ainsi la main.

4. Portez des vêtements de protection conçus pour l'environnement de

travail et pour l'outil.

5. Les chaussures antidérapantes sont recommandées pour maintenir la

stabilité et l'équilibre au sein de l'environnement de travail.

6. Portez des chaussures à embout d'acier ou à coquilles d'acier pour éviter

les blessures aux pieds dues à la chute d'objets.

7. Portez un masque antipoussières ou un appareil respiratoire nominal

approprié.

8. Cet outil peut causer des dommages à l'ouïe. Portez un dispositif de

protection anti-bruit présentant une cote de réduction du bruit

adéquate en fonction du niveau de décibels.

Gardez le contrôle de l'outil, de vos mouvements et de l'environnement

de travail pour éviter les blessures ou le bris de l'outil.

1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,

d'alcool ou de médicaments.

2. Évitez de porter des vêtements ou des bijoux pouvant se prendre

dans les pièces mobiles d'un outil. Gardez les cheveux longs

recouverts ou attachés.

3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en servir.

Une stabilité et un équilibre appropriés sont nécessaires afin d'avoir

un meilleur contrôle en cas de situations inattendues.

La page charge ...

PROPOINT 9082694 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 9082694

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: PROPOINT 9082694 Owner's manual

PROPOINT 9082694 Le manuel du propriétaire

PROPOINT 9082694 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents