PROPOINT 9027988 Le manuel du propriétaire

Catégorie
Coupe-bordures
Taper
Le manuel du propriétaire
V1.0 9027988
Please read and understand all instructions before use. Retain this manual for future reference.
BELT AND DISC SANDER
COMBINATION
9027988 Combination Belt and Disc Sander V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Horsepower
1/2 Hp
No Load Speed
3,580 RPM
Voltage Rating
120V AC
Current Rating
4.3A
Frequency Rating
60Hz
Belt Size 4 x 36 in.
Wheel/Pad Size
6 in.
Switch Type
Rocker
Tool Length 22 in.
Weight
39.7 lb
INTRODUCTION
The combination belt and disc sander is ideal for small-to-large sanding
projects. Perfect for the DIYer or professional woodworker. It features an
angle-adjustable work table for both disc and belt sanding, a rocker switch
and includes a limit plate, wrench and mitre.
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection
and maintenance instructions.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A
notice is an alert that there is a possibility of property damage, injury or death
if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that will
result in severe personal injury or death if the proper
precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that
could result in severe personal injury or death if the proper
precautions are not taken.
V1.0 Combination Belt and Disc Sander 9027988
Visit www.princessauto.com for more information 3
CAUTION! This notice indicates a potentially hazardous situation that may
result in minor or moderate injury if proper practices are not
taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will
result in equipment or property damage, but not personal injury.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-lit
and free of distractions.
2. Keep anyone not wearing the appropriate safety equipment away from
the work area.
3. Store tools properly in a safe and dry location. Keep tools out of the
reach of children.
4. Do not install or use in the presence of flammable gases, dust or liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the Canadian
Standards Association (CSA) or American National Standards Institute
(ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side protection
for the eyes. Eye protection equipment should comply with CSA Z94.3-07
or ANSI Z87.1 standards based on the type of work performed.
2. Wear the appropriate type of full-face shield in addition to safety
googles, as the work can create chips, abrasive or particulate matter.
3. Do not wear gloves when operating a tool that can snag the material and
pull the hand into the tool.
4. Wear protective clothing designed for the work environment and tool.
5. Non-skid footwear is recommended to maintain footing and balance in
the work environment.
6. Wear the appropriate rated dust mask or respirator.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to the tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
9027988 Combination Belt and Disc Sander V1.0
4 For technical questions call 1-800-665-8685
2. Avoid wearing clothes or jewelry that can become entangled with the
moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating the tool. Proper footing and balance
enables better control in unexpected situations.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to the tool safety rules. If you use
this tool unsafely or incorrectly, you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a specific function.
Do not modify or alter this tool or use it for an unintended purpose.
2. Both the sanding belt and the sanding disc are active when power is
applied. Keep hands and fingers away from sanding area. Any part of body
coming in contact with moving parts could cause injury.
3. Never force the tool. Excessive pressure could bend or break the sander,
resulting in damage to the tool, your workpiece or serious personal
injury. If your sander runs smoothly under no load, but does not run
smoothly under load, then excessive pressure is being used.
ELECTRICAL SAFETY
WARNING! Do not touch or handle a live tool with any part of your body
that is wet or damp. Wet skin reduces resistance to electrical current,
increasing the danger of a serious or fatal shock.
WARNING! To reduce risk of electric shock, be certain that the plug is
connected to a properly grounded receptacle.
1. Disconnect tool from power source before cleaning, servicing, changing
parts/accessories or when not in use.
2. Protect yourself against electric shocks when working on electrical
equipment. Avoid body contact with grounded surfaces. There is an
increased chance of electrical shock if your body is grounded.
3. Do not expose the tool to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
4. Do not disconnect the power cord in place of using the ON/OFF switch on the
tool. This will prevent an accidental startup when the power cord is plugged
into the power supply.
4.1 In the event of a power failure, turn off the machine as soon as the
power is interrupted. The possibility of accidental injury could occur
if the power returns and the unit is not switched off.
V1.0 Combination Belt and Disc Sander 9027988
Visit www.princessauto.com for more information 5
5. Do not alter any parts of the tool or accessories. All parts and
accessories are designed with built-in safety features that may be
compromised if altered.
6. Make certain the power source conforms to requirements of your
equipment (see Specifications).
7. When wiring an electrically driven device, follow all electrical and safety
codes, as well as the most recent Canadian Electrical Code (CE) and
Canadian Centre for Occupational Health and Safety (CCOHS).
8. Grounded tools must be plugged into an outlet that is properly installed
and grounded in accordance with all codes and ordinances. Check with a
qualified electrician if you are in doubt as to whether the outlet is
properly grounded. If the tool should electronically malfunction or break
down, grounding provides a low resistance path to carry electricity away
from the user.
8.1 Never remove the grounding prong or modify the plug in any way,
as this will render the tool unsafe.
8.2 Do not use any adapter plugs.
9. This device is only for use on 120 V (single phase) and is equipped with a
3-prong grounded power supply cord and plug.
10. DO NOT use this device with a 2-prong wall receptacle.
10.1 Choose an available 3-prong power outlet.
10.2 Replace 2 prong outlet with a grounded 3-prong receptacle,
installed in accordance with the CE Code and local codes and
ordinances.
WARNING! All wiring should be performed by a qualified electrician.
POWER CORD
1. Insert the power cord plug directly to the power supply whenever
possible. Use extension cords or surge protectors only when the tool's
power cord cannot reach a power supply from the work area.
1.1 Use in conjunction with a Ground Fault Circuit Interrupter (GFCI). If
operating a power tool in a damp location is unavoidable, the use of
a GFCI reduces the risk of electric shock. It is recommended that the
GFCI should have a rated residual current of 30 mA or less.
2. Do not operate this tool if the power cord is frayed or damaged as an electric
shock or surge may occur, resulting in personal injury or property damage.
9027988 Combination Belt and Disc Sander V1.0
6 For technical questions call 1-800-665-8685
2.1 Inspect the tool's power cord for cracks, fraying or other faults in
the insulation or plug before each use.
2.2 Discontinue use if a power cord feels more than comfortably warm
while operating the tool.
2.3 Have the power cord replaced by a qualified service technician.
3. Keep all connections dry and off the ground to reduce the risk of electric
shock. Do not touch plug with wet hands.
4. Prevent damage to the power cord by observing the following:
4.1 Do not pull on the cord to disconnect the plug from an outlet.
4.2 Keep cord away from heat, oil, sharp edges or moving parts.
4.3 Never use the cord to carry the tool.
4.4 Place the electrical cord in a position that prevents it from coming
into contact with the tool and from getting caught by the
workpiece. The cord should always stay behind the tool.
5. Do not allow people, mobile equipment or vehicles to pass over
unprotected power cords.
5.1 Position power cords away from traffic areas.
5.2 Place cords in reinforced conduits.
5.3 Place planks on either side of the power cord to create a protective
trench.
6. Do not wrap cord around the tool as sharp edges may cut insulation or
cause cracks if wound too tight. Gently coil cord and either hang on a
hook or fasten with a device to keep cord together during storage.
POWER TOOL PRECAUTIONS
1. Do not use a power tool with a broken or inoperative trigger/power switch.
2. Do not allow the tool to run without load for an extended period of time,
as this will shorten its life.
3. Do not cover the air vents. Proper cooling of the motor is necessary to
ensure normal life of the tool.
4. Avoid unintentional starting. Ensure the switch is off when connecting to
the power source.
5. Disconnect the power source before installing or servicing the tool.
6. After making adjustments, make sure that any adjustment devices are
securely tightened.
V1.0 Combination Belt and Disc Sander 9027988
Visit www.princessauto.com for more information 7
7. Remove adjusting keys and wrenches before turning the tool on. A
wrench or a key that is left attached to a rotating part of the tool
increases the risk of personal injury.
8. Never force the tool. Excessive pressure could break the tool, resulting in
damage to your workpiece or serious personal injury. If your tool runs
smoothly under no load, but does not run smoothly under load, then
excessive pressure is being used.
9. Do not touch an operating motor. Motors can operate at high
temperatures and can cause a burn injury.
10. Only use accessories that are specifically designed for use with the tool.
Ensure the accessory is tightly installed.
11. Only use an accessory that exceeds the No Load Speed rating (see
Specifications).
12. Never point the tool towards yourself.
KICKBACK PRECAUTIONS
Kickback is a sudden reaction to a pinched or snagged cutting accessory
caught on the material. The material can be ejected and inflict a serious injury
on the user or a bystander. Kickback can also damage the tool or workpiece.
Kickback can be avoided by taking proper precautions:
1. Maintain a firm grip on the material and position your body and arms to
allow you to resist a kickback. Kickback can propel the material in the
direction of the cutting accessorys rotation.
1.1 Position the workpiece so the sanding belt is pulling the workpiece
away from you, against the work table or work guard.
2.1 The sanding disc rotates counter clockwise. Only sand on the left
side of the wheel as the downward force will help to maintain
control of the workpiece. Using the right side may flip the
workpiece upward and cause an injury if control is lost.
2. Use special care when working on corners, sharp edges or flexible
material. These workpieces have a tendency to snag the cutting
accessory.
3. Only use cutting accessories designed for the tool.
9027988 Combination Belt and Disc Sander V1.0
8 For technical questions call 1-800-665-8685
VIBRATION PRECAUTIONS
1. This tool vibrates during use. Repeated or long-term exposure to
vibration may cause temporary or permanent physical injury, particularly
to the hands, arms and shoulders.
2. Anyone using vibrating tools regularly or for an extended period should
first be examined by a doctor and then have regular medical check-ups
to ensure medical problems are not being caused by or worsened from
tool use.
3. If you feel any medical symptoms related to vibrations (such as tingling,
numbness, and white or blue fingers), seek medical attention as soon as
possible.
4. DO NOT use this tool if one of the following applies:
a. Pregnant
b. Impaired blood circulation to the hands
c. Past hand injuries
d. Nervous system disorders
e. Diabetes
f. Raynaud's Disease
5. Do not smoke while operating the tool. Nicotine reduces the blood flow
to the hands and fingers, increasing the risk of vibration-related injury.
6. Wear suitable gloves to reduce the effects of vibration.
7. Use the tool with the least amount of vibration, when there is a choice
between different processes.
8. Do not use for extended periods. Take frequent breaks when using this
tool.
9. Let the tool do the work. Grip the tool as lightly as possible (while still
keeping safe control of it).
10. To reduce vibrations, maintain the tool as explained in this manual. If
abnormal vibrations occur, stop using this tool immediately.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a malfunction
and personal injury.
V1.0 Combination Belt and Disc Sander 9027988
Visit www.princessauto.com for more information 9
Remove the parts and accessories from the packaging and inspect for damage.
Make sure that all items in the parts list are included.
Contents:
Belt Sander
Work Guard
Adjustable Work Table
Mitre Gauge
Adjustment Knob
Hardware
Hex Key, 6 mm
IDENTIFICATION KEY
A Work Guard
B Belt Tension Lever
C Sanding Disc
D Mitre Gauge
E Work Table
F Sanding Belt
G Tracking Control Knob
H Base
I ON/OFF Switch
ASSEMBLY & INSTALLATION
Numbered references in parenthesis (#1) refer to the included Parts List.
Letter references in parenthesis (A) refer to the included Identification Key.
Dashed numbers in parenthesis (Fig. 1-1) refer to a specific point in an
illustration or image.
1. The work table may be installed to use with the sanding disc or the
sanding belt. The work guard must be removed if installing on the
sanding belt.
1.1 Disc - Position the work table against the disc guard with the
support bracket on the face with the dust collector connection.
Align the support brackets pin with the top bolt hole.
Slide a flat washer over the lock knob and insert through the curved
opening and into the threaded bolt hole below the first. Screw the
lock knob in until the work table is secure.
1.2 Belt Position the work table perpendicular to sanders top. Insert
the support brackets pin into the bolt hole on the belt side of the
sander.
9027988 Combination Belt and Disc Sander V1.0
10 For technical questions call 1-800-665-8685
Slide a flat washer over the lock knob and insert through the curved
opening and into the threaded bolt hole parallel to the pin’s bolt
hole. Screw the lock knob in until the work table is secure.
2. Place the work guard across the sanding belt. Bolt the plate to the belt side
of the sander. It is properly installed when there is a space between the belt
and the work guard.
MOUNT TOOL ON A WOOD WORKBENCH
The hardware to mount the tool is not included.
1. Clean the work area where the tool will be mounted.
2. Position the tool, check that it will be level and there are no obstructions
around it that will interfere with a long workpiece.
3. Mark the workbench through the holes in the base of the tool.
4. Move the tool aside and drill holes through the workbench equal to the
diameter of the bolts.
5. Align the tool’s bolt holes with the holes drilled in the workbench.
6. Drop a bolt through the bolt holes. Ensure the bolt is long enough to
protrude from the bottom of the workbench.
7. Slide a flat washer over the bolt and secure the tool in place with a nut.
Repeat with each bolt. Tighten all bolts.
SAWDUST PORT
The sawdust port directs the accumulated sawdust from the tool. Connect a
dust collection system to the 2-1/4 in. sawdust port. Attach a bag that is not
airtight to the port if a dust collection system isn’t available. Continue to wear
a dust mask as sawdust may still be suspended in the air.
OPERATION
SAFETY LOCK SWITCH
Remove the yellow tab of the ON/OFF switch to prevent the tool from being
switched on. Reinsert to yellow tab and push to click into place. The ON/OFF
switch is functional again.
ADJUST THE SANDING BELT TRACKING
1. Quickly turn the power ON and then OFF while watching the end of the
belt jutting out from the base. Adjust the tracking if the belt slides
towards the front or rear.
V1.0 Combination Belt and Disc Sander 9027988
Visit www.princessauto.com for more information 11
2. Move the tracking control knob (G) a 1/4 turn. Move downward if the
belt moved to the front. Move upward if the belt slid towards the rear.
3. Repeat steps 1 and 2 until the tracking is correct. You may need to
reduce to a 1/8 turn to refine the tracking.
ADJUST PLAT FORM ANGLE
Reposition the belt sander from horizontal to 90º vertical, based on the work
being done. Ensure you are able to work comfortably at the chosen angle to
avoid fatigue and injury.
1. Insert the 6 mm hex key into the bolt on the rear of the belt sander
platform and loosen.
2. Raise or lower the platform until it has reached the desired angle.
3. Tighten the bolt again to secure the platform in place.
4. Replace the work guard with the work table when sanding with the
platform at an angle.
SANDING DISC
1. The sanding disc rotates counterclockwise. Place the workpiece on the
work table and slowly push it into the left side of the sanding disc. This
will prevent a kickback.
2. Move towards the sanding disc’s outer edge to remove more material and
closer to the center to remove less material.
SANDING
1. Hold the workpiece firmly and lightly press against the sanding belt (F).
Use the work guard (A) or work table (E) for support during sanding.
Apply just enough pressure to remove the desired amount of material.
Move the workpiece back and forth across the belt.
2. Use the end of the sanding platform that juts out to sand inside curves.
Always press the workpiece against the upper curve of the belt to
prevent kickback. Continue to move the workpiece back and forth until
the desired surface is achieved.
3. Sand outer curves on the sanding disc, using the work table as support
WORK TABLE
WARNING! Changing the work table angle may leave a gap larger than 1/8
in. between the table edge and sanding belt/disc. A finger may become
trapped in this gap when the tool is operating and result in an injury.
Position your hands to prevent this from happening.
9027988 Combination Belt and Disc Sander V1.0
12 For technical questions call 1-800-665-8685
The work table (E) is held in place by a pin and locking knob (see Installation)
on either the rear for use with the sanding belt or the left side for use with
the sanding disc.
The work table can be repositioned at an angle in relation to the sanding belt
or disc. There is a degree gauge on the left side of the tool, but an angle
finder tool is recommended for greater accuracy.
The work table has a slot for the mitre gauge.
MITRE GAUGE
The mitre gauge (D) placed into the work table’s slot, allows a workpiece to
move back and forth against the sanding belt or disc, while maintaining a
constant angle. The mitre gauge can be set to 60º angle on either side of the
center point.
The angled edge will have a wider width than the workpiece width. Measure
the length of the angled cut to determine if the sanding belt or disc should is
more suitable for the workpiece.
1. Loosen the locking knob on the mitre gauge.
2. Rotate either left or right to obtain the correct angle. Use an angle finder
for greater accuracy.
3. Tighten the locking gauge.
4. Place the mitre gauge into the work table slot.
5. Hold the workpiece against the mitre gauge, then move the workpiece
along the gauge into the sanding belt or disc. Move back and forth while
gradually feeding the workpiece into the sanding belt/disc.
6. Pull the workpiece back along the mitre gauge, then remove the
workpiece entirely to inspect.
7. Use the mitre gauge with small workpieces to better retain control while
sanding.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient, easier
to control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace damaged or
worn components. Only use identical replacement parts when servicing.
3. Follow instructions for lubricating and changing accessories.
4. Only use accessories intended for use with this tool.
V1.0 Combination Belt and Disc Sander 9027988
Visit www.princessauto.com for more information 13
5. Keep the tool handles clean, dry and free from oil/grease at all times.
6. Maintain the tool’s labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd. for
replacements.
WARNING! Only qualified service personnel should repair the tool. An
improperly repaired tool may present a hazard to the user and/or others.
REPLACING THE SANDING BELT
The sanding belt may become worn or you may want to change the level of
grit for a project. The steps to replace the belt is the same in both instances.
1. Ensure the tool is OFF, the yellow tab is removed from the safety switch and
the tool is unplugged.
2. Raise the sanding belt platform angle enough to allow easy access to the
bottom of the sanding belt.
3. Slide the belt tension lever (B) to the right to release tension on the belt.
4. Hold the belt by both ends and slide it toward the front, off of the platform.
5. Check if the new belt has a direction arrow on the inner backing. The sanding
belt rotates counter clockwise. Match the direction arrow with the rotation.
6. Hold both ends of the new belt and slide it onto the platform. You may need
to adjust the top and bottom of the belt for fit while installing to avoid
damaging the belt.
7. Slide the belt tension lever to the left to take up the belts slack. The belt is
ready for use once the slack disappears.
8. Test that the tracking is properly set (See Assembly & Installation).
REPLACING THE SANDING DISC
1. Ensure the tool is OFF, the yellow tab is removed from the safety switch
and the tool is unplugged.
2. Remove the work table and set aside.
3. Pull the old sanding disc from the sanding plate carefully to avoid tearing
the disc.
4. Check and remove any remaining adhesive.
5. Remove the backing from the new sanding disc. Apply the disc onto the
plate carefully to avoid folds or creases. The sanding disc should cover
the plate without hanging over the plate’s edge.
9027988 Combination Belt and Disc Sander V1.0
14 For technical questions call 1-800-665-8685
6. Align the disc guard with the screw holes on either side of the sanding
plate and fasten into place.
CLEANING
1. Dress the sanding belt and discs with a dressing stick to remove sanding
residue from the surface. This will extend their useful lifespan.
2. Vacuum the tool’s inside to remove collected sawdust.
3. Wipe down exterior surfaces with a damp cloth to remove accumulated
dust.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function
properly or parts are missing. If unable to do so, have a qualified technician
service the tool.
PROBLEM(S)
POSSIBLE CAUSE(S)
SUGGESTED SOLUTION(S)
Sanding grit does
not remain on belt
or discs.
1. Exposed to dry
conditions that have
caused the adhesive to
become brittle.
2. The sanding belt or disc
is damaged or creased.
1. Store sanding belts and discs
in a location that does not
have extreme temperature or
dryness.
2. Store sanding belts and discs
flat. Do not fold either for
storage.
Deep grooves
appear in the
workpiece.
1. Sanding grit is too
coarse.
2. Sanding across the
wood grain.
3. Excessive pressure
against the sanding
belt/disc.
4. Workpiece held in place
too long.
1. Change to a finer grit.
2. Sand with the wood grain.
3. Reduce pressure on workpiece
while sanding.
4. Move the workpiece from side
to side while sanding.
V1.0 Combination Belt and Disc Sander 9027988
Visit www.princessauto.com for more information 15
Sanding belt or
disc is clogged.
1. Sanding a soft wood.
2. Excessive pressure
against the sanding
belt/disc.
1. Clean sanding belt/disc with a
dressing stick frequently.
2. Reduce pressure on workpiece
while sanding.
Burns appear on
workpiece.
1. Excessive pressure
against the sanding
belt/disc.
2. Workpiece held in place
too long.
3. Sanding grit is too fine.
1. Reduce pressure on workpiece
while sanding.
2. Move the workpiece from side
to side while sanding.
3. Change to a coarser grit.
Motor does not
start. Fuses or
circuit breakers
tripping or
blowing.
1. Low voltage when
drawing current.
2. Short circuit in line,
power cord or plug.
3. Short circuit in motor or
loose connections.
4. Incorrect fuses or circuit
breakers in power line.
1. Check power source for proper
voltage.
2. Inspect cord or plug for
damaged insulation and
shorted wires.
3. Inspect all connections on
motor for loose or shorted
terminals and/or worn
insulation.
4. Install correct fuses or circuit
breakers or switch tool to an
appropriately sized circuit.
Machine slows
when operating.
1. Feed rate into sanding
belt/disc too great.
2. Low Voltage due to
insufficiently powered
circuit.
3. Wrong gauge extension
cord.
1. Slow rate of feed into the
sanding belt/disc.
2. Attach to power circuit with
adequate amperage.
3. Replace with a thicker gauge
extension cord.
Excessive machine
vibration.
1. Tool mounting incorrect.
2. Incorrect tension set on
sanding belt.
3. Tension spring
malfunctions.
4. Idler roller is loose.
5. Sanding belt/disc is
damaged.
1. Have motor mountings
inspected and adjusted.
2. Readjust belt tension. Replace
belt if necessary.
3. Have tension spring replaced.
4. Adjust or replace the idler
roll er.
5. Replace sanding belt/disc.
9027988 Combination Belt and Disc Sander V1.0
16 For technical questions call 1-800-665-8685
PROBLEM(S)
POSSIBLE CAUSE(S)
SUGGESTED SOLUTION(S)
Workpiece is
pulled out of your
hands.
1. Workpiece is not
supported.
2. Workpiece is too small.
1. Use the work guard or work
table to support the
workpiece.
2. Hold workpiece with jip or
grasping tool. Also ensure
using work table and mitre
gauge for support.
Workpiece is
kicking back.
Sanding on wrong side of
sanding disc.
Sand on the left side of the disc.
See Kickback Precautions.
V 1,0 9027988
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce manuel
afin de pouvoir le consulter plus tard.
PONCEUSE À COURROIE
ET À DISQUE
COMBINAISON
9027988 Ponceuse à courroie et à disque combinaison V 1,0
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Puissance
1/2 CV
Vitesse à vide
3 580 tr/min
Tension nominale
120 V c.a.
Courant nominal
4,3 A
Fréquence nominale
60 Hz
Taille de la courroie
4 x 36 po
Taille de roue/patin
6 po
Type de commutateur
Culbuteur
Longueur de l’outil
22 po
Poids
39,7 lb
INTRODUCTION
Ponceuse à courroie et à disque combinaison est idéale pour les petits et
grands projets de ponçage. Parfaite pour les bricoleurs ou les ouvriers
professionnels. Elle se caractérise par un établi à angle réglable pour le
ponçage à disque ou à courroie, un interrupteur basculant et comprend une
plaque de limitation, une clé et un onglet.
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant
d'utiliser cet outil. L'utilisateur doit respecter les précautions de base
lorsqu'il utilise cet outil afin de réduire le risque de blessure ou de
dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection et
d'entretien.
DÉFINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce
manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage à la
propriété, de blessure ou de décès si on ne respecte pas certaines instructions.
DANGER ! Cet avis indique un risque immédiat et particulier qui
entraînera des blessures corporelles graves ou même la
mort si on omet de prendre les précautions nécessaires.
V 1,0 Ponceuse à courroie et à disque combinaison 9027988
Visitez www.princessauto.com pour plus d'informations 3
AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui pourrait entraîner des blessures
corporelles graves ou même la mort si on omet de
prendre les précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement dangereuse
qui peut entraîner des blessures mineures ou modérées si
on ne procède pas de la façon recommandée.
AVIS ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui entraînera des dommages au niveau de
l'équipement ou des biens, mais non des blessures
corporelles.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez votre aire
de travail propre, bien éclairée et exempte de toute distraction.
2. Assurez-vous que les personnes qui ne portent pas l'équipement de
sécurité approprié ne se trouvent pas à proximité de l'aire de travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec. Gardez les
outils hors de la portée des enfants.
4. N'installez pas et n'utilisez pas d'outils électriques en présence de gaz,
de poussière ou de liquides inflammables.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection personnelle
homologué par l'Association canadienne de normalisation (CSA) ou
l'American National Standards Institute (ANSI).
ÉQUIPEMENT DE PROTECTION PERSONNELLE
1. Portez toujours des lunettes antiprojections qui offrent une protection
frontale et latérale pour les yeux. L'équipement de protection des yeux
devrait être conforme à la norme CSA Z94.3-07 ou ANSI Z87.1 fonction du
type de travail effectué.
2. Portez un écran facial panoramique de type approprié avec les lunettes
de sécurité puisque cette tâche peut créer des copeaux, des matières
abrasives ou des particules.
3. Ne portez pas de gants lorsque vous utilisez un outil dans lequel le
tissu pourrait demeurer coincé, entraînant ainsi la main.
9027988 Ponceuse à courroie et à disque combinaison V 1,0
4 En cas de questions techniques, appelez le 1-800-665-8685
4. Portez des vêtements de protection conçus pour l'environnement de
travail et pour l'outil.
5. Les chaussures antidérapantes sont recommandées pour maintenir la
stabilité et l'équilibre au sein de l'environnement de travail.
6. Portez un masque antipoussières ou un appareil respiratoire nominal
approprié.
PRÉCAUTIONS PERSONNELLES
Gardez le contrôle de l'outil, de vos mouvements et de l'environnement de
travail pour éviter les blessures ou le bris de l'outil.
1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,
d'alcool ou de médicaments.
2. Évitez de porter des vêtements ou des bijoux pouvant se prendre dans
les pièces mobiles d'un outil. Gardez les cheveux longs recouverts ou
attachés.
3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en servir. Une
stabilité et un équilibre appropriés sont nécessaires afin d'avoir un
meilleur contrôle en cas de situations inattendues.
CONSIGNES DE SÉCURITÉ SPÉCIFIQUES
AVERTISSEMENT ! Ne permettez PAS au confort ou à votre familiarisation
avec l'outil (obtenus après un emploi répété) de se substituer à une
adhésion stricte aux règles de sécurité de l'outil. Si vous utilisez cet outil de
façon dangereuse ou incorrecte, vous pouvez subir des blessures corporelles
graves.
1. Utilisez le bon outil pour la tâche à effectuer. Cet outil a été conçu pour
une utilisation spécifique. Évitez de modifier ou d'altérer cet outil ou de
l'utiliser à une fin autre que celle pour laquelle il a été conçu.
2. La courroie abrasive et le disque abrasif sont actifs lorsqu’on les place
sous tension. Gardez les mains et les doigts éloignés de la zone de
ponçage. Toute partie du corps venant en contact avec des pièces
mobiles peut subir des blessures.
3. Ne forcez jamais l'outil. Une pression excessive pourrait casser la
ponceuse, ce qui causerait des dommages de la pièce de travail ou des
blessures graves. Une pression excessive est utilisée si la ponceuse à
main fonctionne sans à-coups à vide mais pas avec une charge.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

PROPOINT 9027988 Le manuel du propriétaire

Catégorie
Coupe-bordures
Taper
Le manuel du propriétaire

dans d''autres langues