Powerfist 9032202 Le manuel du propriétaire

Taper
Le manuel du propriétaire
SPECIFICATIONS
HAZARD DEFINITIONS
INTRODUCTION
SAFETY
WARNING! Read and understand all instructions before
using this tool. The operator must follow basic
precautions to reduce the risk of personal injury
and/or damage to the equipment.
WORK AREA
PERSONAL SAFETY
WARNING! Some dust created by power tools may
contain lead, crystalline silica, arsenic and chromium,
which are known cause cancer, birth defects or other
reproductive harm. Ensure work area is well ventilated
and always wear recommended personal protective
equipment.
WARNING! Wear personal protective equipment
approved by the Canadian Standards Association (CSA)
or American National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
PERSONAL PRECAUTIONS
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with
product (gained from repeated use) replace strict
adherence to the tool safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious personal
injury.
POWER TOOL PRECAUTIONS
ELECTRICAL SAFETY
WARNING! Do not touch or handle a live tool with any
part of your body that is wet or damp. Wet skin
reduces resistance to electrical current, increasing
the danger of a serious or fatal shock.
WARNING! To reduce risk of electric shock, be certain
that the plug is connected to a properly grounded
receptacle.
WARNING! Do not let your fingers touch the terminals
or plug when installing ot removing from the outlet.
UNPACKING
WARNING! Do not operate the tool if any part is
missing. Replace the missing part before operating.
Failure to do so could
result in a malfunction and
personal injury.
ASSEMBLY & INSTALLATION
MOUNTING THE DUST CHUTE
MOUNTING THE DISC TABLE
MOUNTING THE BELT TABLE
DUST PORT
BACKSTOP
MOUNTING TO A SURFACE
OPERATION
ADJUSTING THE DISC TABLE
ADJUSTING THE BELT TABLE
SURFACE SANDING
END SANDING
CONTOUR SANDING
USING THE MITRE GAUGE
CARE & MAINTENANCE
WARNING! Always unplug the tool before performing
any inspections or maintenance.
WARNING! Only qualified service personnel should
repair the tool. An improperly repaired tool may
present a hazard to the user and/or others.
ABRASIVE BELT REPLACEMENT
ABRASIVE DISC REPLACEMENT
ADJUSTING ABRASIVE BELT TRACKING
CLEANING
WARNING! Clean the dust collector and guards before
using tool for any metal grinding purposes. Sparks can
potentially ignite debris and start fires.
WARNING! Never use highly volatile solvents. Avoid
getting cleaning solution on paint as it tends to
deteriorate these finishes. Use soap and water on
painted components.
LUBRICATION
NOTICE! NEVER use a penetrating oil to lubricate the
tool. Penetrating oil may act as a solvent that can
break down the grease and cause the tool to seize up.
DISPOSAL
IMPORTANT! DO NOT pollute the environment by
allowing uncontrolled discharge of waste oil.
TROUBLESHOOTING
Problem(s)
Possible Cause(s)
Suggested
Solution(s)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Powerfist 9032202 Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues