PROPOINT 8843906 Le manuel du propriétaire

Catégorie
Outils électroportatifs
Taper
Le manuel du propriétaire
V1.0 8843906
Please read and understand all instructions before use. Retain this manual for future reference.
AIR DRILL
3/8 in. REVERSIBLE
8843906 3/8 in. Reversible Air Drill V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Max. Pressure
90 PSI
Air Consumption @ 90 PSI 3.36 CFM
No Load Speed 2,200 RPM
Chuck Size 3/8 in.
Chuck Type Keyless
Air Inlet 1/4 in. NPT
Min. Hose Size 3/8 in.
Reversible Yes
Material Die-cast Aluminum Housing
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A
notice is an alert that there is a possibility of property damage, injury or death if
certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that will
result in severe personal injury or death if the proper
precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that
could result in severe personal injury or death if the proper
precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that may
result in minor or moderate injury if proper practices are not
taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will
result in equipment or property damage, but not personal injury.
V1.0 3/8 in. Reversible Air Drill 8843906
Visit www.princessauto.com for more information 3
INTRODUCTION
The 3/8 in. Reversible Air Drill is ideal for home improvement projects,
autobody work and general assembly or repairs.
SAFETY
WARNING! Read and understand all instructions before using this tool.
The operator must follow basic precautions to reduce the risk of
personal injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection and
maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-lit
and free of distractions. Place lights so you are not working in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from the
work area.
3. Store unused tools properly in a safe and dry location to prevent rust or
damage. Lock tools away and keep out of the reach of children.
4. Do not install or use in the presence of flammable gases, dust or liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the
Canadian Standards Association (CSA) or American National Standards
Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side protection
for the eyes. Eye protection equipment should comply with CSA Z94.3-07
or ANSI Z87.1 standards based on the type of work performed.
2. Wear the appropriate type of full-face shield in addition to safety googles,
as the work can create chips, abrasive or particulate matter.
3. Wear gloves that provide protection based on the work materials or to
reduce the effects of tool vibration.
3.1 Do not wear gloves when operating a tool that can snag the material
and pull the hand into the tool.
4. Wear protective clothing designed for the work environment and tool.
5. Non-skid footwear is recommended to maintain footing and balance in the
work environment.
8843906 3/8 in. Reversible Air Drill V1.0
4 For technical questions call 1-800-665-8685
6. This tool can cause hearing damage. Wear hearing protection gear with
an appropriate Noise Reduction Rating to withstand the decibel levels.
7. The tool may contain high pressure. Use safety glasses and gloves for
protection during operation. Keep hands clear of the exposed rubber
portions of the hose.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the
moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and balance
enables better control in unexpected situations.
4. Support the workpiece or clamp it to a stable platform. Holding the
workpiece by hand or against your body may lead to personal injury.
5. Keep your fingers away from the trigger/switch while carrying the tool, attaching
an air hose or an accessory. Lock the trigger/switch safety if available.
6. Avoid unintentional starts. Be sure that the regulator/throttle switch is in
the neutral or OFF position when not in use and before connecting it to
any air source.
7. Serious injury or death may occur from inhaling compressed air. The air
stream may contain carbon monoxide, toxic vapors or solid particles.
Never inhale compressed air directly from the pump or air tool.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to the tool safety rules. If you use
this tool unsafely or incorrectly, you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a specific function.
Do not modify or alter this tool or use it for an unintended purpose.
2. Do not use the tool if any parts are damage broken or misplaced. Repair
or replace the parts.
3. This tool will not stop moving immediately. Do not lay the tool down or
leave it unattended until it has come to a complete stop. A part that is
moving could make the tool jump or grab a surface and pull the tool out
of your control.
V1.0 3/8 in. Reversible Air Drill 8843906
Visit www.princessauto.com for more information 5
4. Always make sure the work surface is free from nails and other foreign
objects.
5. Always use the correct chuck size. If the chuck size is larger than the
accessory shank size it will not grip the shank properly, leading to
possible injury to the operator, damage to the tool or work piece.
6. Always check accessory bits for damage before each use. Damaged
accessories can break during use and cause serious injury.
7. Never use dull or damaged bits. Sharp bits must be handled with care.
Damaged bits can snap during use. Dull bits require more force to push
the tool, possibly causing the bit to break.
8. Maintain a firm grip on the tool and position your body and arms to allow
you to resist kickback forces. Kickback will propel the tool in the direction
opposite to the tool’s movement at the time of snagging.
9. Use metal and voltage detectors to locate hidden electric, water or gas
lines. Avoid touching live components or conductors.
10. Before drilling, check that there is sufficient clearance for the drill bit
under the workpiece.
11. If you are interrupted when operating the drill, complete the process and
switch off the tool before looking up.
AIR TOOL PRECAUTIONS
1. Use only clean and dry compressed air as a power source. Contaminated
or moist air will gradually damage the tool.
2. Install an in-line shutoff valve or regulator to allow immediate control over
the air supply in an emergency, even if a hose is ruptured.
3. Discontinue tool use if it does not work properly or air is leaking. Tag or
mark the tool as ‘defective’ or ‘out of service’ until repaired.
4. Check the manufacturer’s maximum pressure rating for air tools and
accessories. Compressor outlet pressure must be regulated to never
exceed the maximum pressure rating of the tool (see Specifications).
Exceeding the maximum PSI rating can create a bursting hazard, causing
injury and property damage.
5. Attach all accessories properly to the tool before connecting the air
supply. A loose accessory may detach or break during operation.
6. Never use oxygen, combustible gas or any other bottled gas as a power
source. Any power source other than an air compressor could cause an
explosion and serious personal injury.
8843906 3/8 in. Reversible Air Drill V1.0
6 For technical questions call 1-800-665-8685
7. Turn OFF the valve and discharge any remaining air pressure after each
use or before adjusting the tool.
8. Do not leave the air tool unattended with its compressed air supply on.
Turn off the compressed air supply and bleed the air tool of any
remaining compressed air before leaving the air tool unattended.
9. Serious injury may occur from loose debris being propelled at high
speeds from the compressed air stream. Always wear OSHA approved
safety glasses to protect the eyes during operation of the air compressor.
10. Never point the air stream or tools at any point of your body, other people
or animals. Debris and dust may be ejected without warning. Always turn
off the air compressor and drain tank pressure completely before
attempting maintenance or attaching air tools. Release pressure slowly
from the system.
AIR HOSE PRECAUTIONS
1. Inspect the tool's air hose for cracks, fraying or other faults before each
use. Discontinue use if the air hose is damaged or hissing is heard from
the air hose or couplers. Replace the defective air hose.
2. Do not allow people, mobile equipment or vehicles to pass over the
unprotected air hose. Position the air hose away from high traffic areas, in
a reinforced conduit or place planks on both sides of the air hose to
create a protective trench.
3. Prevent damage to the air hose by observing the following:
3.1 Never carry the tool by the air hose.
3.2 Keep the air hose behind the tool and out of the tool's work path.
3.3 Keep the air hose away from heat, oil, sharp edges or moving parts.
3.4 Do not wrap the air hose around the tool as sharp edges may pierce
or crack the air hose. Gently coil the hose and either hang on a
hook or fasten with a device to keep hose together when storing.
4. A damaged or disconnected air hose under pressure may whip around
and inflict personal injury or damage the work area. Secure the
compressor's air hose to a fixed or permanent structure with clamps or
cable ties.
COMPRESSOR/TANK PRECAUTIONS
DANGER! Do not use an air tank beyond its expiration date. A tank
rupture or explosion may kill or cause a serious injury to yourself or a
bystander. Disable and discard the air tank according to the your
municipality by-laws.
V1.0 3/8 in. Reversible Air Drill 8843906
Visit www.princessauto.com for more information 7
1. Never drill into, weld, patch or modify the air tank. Immediately replace the
tank or compressor if an air leak develops. The leak may lead to a rupture.
2. Never make adjustments to the components that control tank pressure.
Serious injury or death may occur if modifications are made to the
pressure switch, safety relief valve or other components that control the
tank pressure.
3. Check operation of the pressure relief valve on a regular basis and never
operate without a factory approved pressure relief valve. Do not make
alterations to the factory operating pressure settings.
POWER TOOL PRECAUTIONS
Tool accessory is a general term that refers to drill bit, saw or cutting blades,
grinding wheel, etc. as appropriate for the tool.
1. Do not use any power tool with a malfunctioning power switch or control.
A power tool that fails to respond to the controls is dangerous and can
cause an injury. A qualified technician must repair and verify the power
tool is operating correctly, before it can be used.
2. Do not cover the air vents.
3. Disconnect the power source before installing or servicing the tool.
4. Never force the tool. Excessive pressure could break the tool, resulting in
damage to your workpiece or serious personal injury. Excessive pressure is
the cause if your tool runs smoothly under no load, but roughly under load.
5. Keep hands and fingers away from the work area. Any part of body
contacting the tool’s working parts could cause an injury.
6. Only use accessories that are specifically designed for use with the tool.
Ensure the accessory is tightly installed.
7. Only use an accessory that exceeds the No Load Speed rating (see
Specifications).
8. Before using the tool on a workpiece, test the tool by running it at the
highest no load speed for at least 30 seconds in a safe position. Stop
immediately if there is any abnormal vibration or wobbling. Check the tool
to determine the cause.
9. Never touch the tool accessory or workpiece during or immediately after
use. They may be hot and could inflict a burn injury.
10. Never use a tool with a cracked or worn tool accessory. Change the tool
accessory before using it.
8843906 3/8 in. Reversible Air Drill V1.0
8 For technical questions call 1-800-665-8685
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a
malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for
damage. Make sure that all items in the contents are included.
Contents: Air Drill Handle
ASSEMBLY & INSTALLATION
INSTALL AIR COUPLER
Prepare a standard 1/4 in. NPT male air coupler for use with your tool.
1. Wrap the external threads of the male coupler with sealant tape.
1.1 Wrap tape in a clockwise direction so it will not unravel.
1.2 Do not tape all the threads. Leave several leading threads
unwrapped for easier alignment.
2. Screw the coupler into the tool's air inlet and tighten with a wrench
until snug.
3. Run the compressor at a low volume and check the connection for air
leaks. Do not use the tool until all air leaks are repaired or the faulty
component is replaced.
IMPORTANT! Vibration may cause failure if a quick coupler is connected
directly to the air tool. To overcome this, connect a leader hose to the
tool. A quick coupler may then be used to connect the leader hose to
the air line hose.
OPERATION
PRESSURE DROP
Apply the air consumption and pressure rate numbers to the tools air inlet, not
the compressors outlet. Calculate the pressure drop for your air supply set-up
and increase the compressor outlet pressure to compensate. Make sure you do
not exceed the maximum pressure for any part of your air supply system.
Installing a pressure gauge at the tool inlet is the best way to measure the air
pressure and adjust the compressors output.
TOOL OPERATION
1. Clean the air drill of packing grease before first use. See the Air Tool
Lubrication section for instructions.
V1.0 3/8 in. Reversible Air Drill 8843906
Visit www.princessauto.com for more information 9
2. Install a drill bit into the chuck and hand-tighten. Make sure the bit’s shaft
is straight.
3. Connect the air drill to the end of the air hose.
4. Set the compressor to the correct air pressure and flow (see
Specifications). Start the compressor.
5. Push the switch above trigger to the right to set the tool to forward. Push
the switch to the left to set the drill in reverse.
6. Test the drill under no load to confirm the bit is installed correctly.
7. Place the drill bit point onto the workpiece surface.
7.1 Use a center punch to mark the spot to prevent the drill bit from
skittering across the surface.
7.2 A larger drill bit may require a pilot hole. Use a narrower bit to drill
the pilot hole first, then install the larger bit.
7.3 Apply a drop of cutting oil to the drill bit and surface before cutting
metal.
8. Squeeze the trigger and lightly push the drill against the workpiece.
Continue to apply pressure until the proper depth is reached.
9. Hold the trigger until the drill bit is removed from the hole, then release
the trigger.
10. Shut the compressor off once the task is completed. Squeeze the trigger
to release residual compressed air from the hose and tool. Disconnect
the tool.
11. Remove the bit and store both the bit and the drill.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient, easier to
control and will have fewer problems.
2. Inspect the tool fittings, alignment, hoses and power supply cord periodically.
Have damaged or worn components repaired or replaced by an authorized
technician. Only use identical replacement parts when servicing.
3. Follow instructions for lubricating and changing accessories.
4. Only use accessories intended for use with this tool.
5. Keep the tool handles clean, dry and free from oil/grease at all times.
6. Maintain the tool’s labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd. for
replacements.
WARNING! Only qualified service personnel should repair the tool. An
improperly repaired tool may present a hazard to the user and/or others.
8843906 3/8 in. Reversible Air Drill V1.0
10 For technical questions call 1-800-665-8685
AIR TOOL LUBRICATION
NOTICE! Only use air tool oil to lubricate the tool. Other lubricants are
not suitable and will damage the tool or cause a malfunction during use.
NOTICE! Never use a penetrating oil to lubricate an air tool. Penetrating
oil acts as a solvent that will dissolve the tool’s grease packing and may
damage the o-rings, causing the tool to seize or malfunction.
1. All air tools have an internal coating of grease to prevent corrosion during
shipping and storage. Remove this grease by adding a generous amount
of air tool oil in the air inlet and then run the tool under no load until the
exhaust is clear.
2. Manually add a drop or two of air tool oil into the tool’s male coupler
before each use and after every hour of continuous use. The tool will not
work properly without lubrication and parts will wear prematurely.
3. Avoid adding too much air tool oil as this can cause premature power
loss and eventual tool failure. A qualified technician will need to take the
tool apart and clean out the excess oil.
4. Apply a generous amount of air tool oil to the tool before storing it for an
extended period of time (overnight, weekend, etc.). Run the tool for
approximately 30 seconds to ensure the oil is evenly distributed
throughout the tool. Store it in a clean and dry location.
STORAGE
When not in use for an extended period, apply a thin coat of lubricant to the
steel parts to avoid rust. Remove the lubricant before using the tool again.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.
IMPORTANT! DO NOT pollute the environment by allowing uncontrolled
discharge of waste oil.
V1.0 3/8 in. Reversible Air Drill 8843906
Visit www.princessauto.com for more information 11
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function
properly or parts are missing. If unable to do so, have a qualified technician
service the tool.
PROBLEM(S) POSSIBLE CAUSE(S) SUGGESTED SOLUTION(S)
Tool runs at
normal speed,
but loses power
under load.
Motor parts worn. 1. Have a qualified technician
service the tool.
2. Replace tool or parts.
Tool runs slowly.
Air flows slightly
from exhaust.
Motor parts jammed
with dirt particles.
OR
Airflow blocked by dirt.
1. Check air inlet filter for
blockage.
2. Pour air tool lubricating oil into
air inlet as per lubrication
instructions for clearing
shipping grease.
3. Operate tool in short bursts to
clear debris.
4. If tool still jammed, clean tool
and lubricate per lubrication
instructions.
Tool runs slowly.
Air flows slightly
from exhaust.
Air regulator in closed
position.
Open the air regulator to desired
airflow.
Tool will not run.
Air flows freely
from exhaust.
Damage or excessive
wearing of internal
parts.
1. Have a qualified technician
service the tool.
2. Replace tool or parts.
Tool will not shut
off.
1. Throttle valve o-ring
dislodged from seat
inlet valve.
2. Trigger mechanism
jammed or dirty.
1. Replace throttle valve o-rings.
2. Clean trigger mechanism and
lubricate.
Loss of power
or erratic
performance.
1. Excessive drain on
the air hose. Incorrect
size or type of hose
couplers.
2.
Moisture or restriction
in the air hose/tank
3. Air compressor has
insufficient flow.
1. Check the air hose and
confirm the hose fitting is
correct for the inlet bushing.
2. Depressurize system and drain
tank and air hose of water.
3. Ensure tool is connected to a
compressor with a rate flow
that matches the tool.
8843906 3/8 in. Reversible Air Drill V1.0
12 For technical questions call 1-800-665-8685
PARTS BREAKDOWN
V1.0 3/8 in. Reversible Air Drill 8843906
Visit www.princessauto.com for more information 13
PARTS LIST
# DESCRIPTION QTY
1 Housing 1
2 Trigger Nut 2
3 Spring 1
4 O-Ring 1
5 O-Ring 1
6 Valve Stem 1
7 O-Ring 1
8 Bushing 1
9 Switch 1
10 Steel Plate 1
Trigger Spring
1
12 Trigger 1
13 Screw 1
14 Pin 1
15 Muffle Cover 1
16 Air Inlet 1
17 Grip 1
18 Cylinder Assembly 1
18.1 Gasket 1
18.2 Bearing 1
18.3 End Plate 1
18.4 Rotor 1
18.5 Rotor Blade 5
18.6 Cylinder 1
18.7 Pin 1
18.8 Front Plate 1
18.9 Bearing 1
19 Washer 1
20 Bearing 1
21 Pin 2
22 Gear 2
23 Work Spindle 1
24 Gear Ring 1
25 Bearing 2
26 Retainer 1
27 Washer 1
28 Chuck 1
29 Chuck Screw 1
30 O-Ring 1
8843906 3/8 in. Reversible Air Drill V1.0
14 For technical questions call 1-800-665-8685
V1,0 8843906
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce
manuel afin de pouvoir le consulter plus tard.
PERCEUSE PNEUMATIQUE
RÉVERSIBLE À PRISE PISTOLET DE 3/8 PO
8843906 Perceuse pneumatique réversible à prise pistolet de 3/8 po V1,0
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Pression max. 90 lb/po carré
Consommation dair à 90 lb/po carré
3,36 pi cubes/min
Vitesse à vide 2 200 tr/min
Taille de mandrin
3/8 po
Type de mandrin Sans clé
Entrée dair
1/4 po NPT
Diamètre min. de tuyau (po) 3/8 po
Réversible Oui
Matériaux Boîtier en aluminum coulé
DÉFINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans
ce manuel. Un avis est une alerte indiquant qu'il existe un risque de
dommage à la propriété, de blessure ou de décès si on ne respecte pas
certaines instructions.
DANGER ! Cet avis indique un risque immédiat et particulier qui
entrnera des blessures corporelles graves ou
même la mort si on omet de prendre les
précautions nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une
pratique non sécuritaire qui pourrait entraîner des
blessures corporelles graves ou même la mort si
on omet de prendre les précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement
dangereuse qui peut entraîner des blessures
mineures ou modérées si on ne procède pas de la
façon recommandée.
AVIS ! Cet avis indique un risque particulier ou une pratique
non sécuritaire qui entraînera des dommages au niveau
de l'équipement ou des biens, mais non des blessures
corporelles.
V1,0 Perceuse pneumatique réversible à prise pistolet de 3/8 po 8843906
Visitez www.princessauto.com pour plus d'informations 3
INTRODUCTION
La perceuse pneumatique réversible à prise pistolet de 3/8 po est
idéale pour les projets de rénovation résidentielle, les travaux de
carrosserie dautomobile et dassemblage généraux ou les réparations.
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les
instructions avant d'utiliser cet outil. L'utilisateur doit respecter
les précautions de base lorsqu'il utilise cet outil afin de réduire
le risque de blessure ou de dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection et
d'entretien.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez
votre aire de travail propre, bien éclairée et exempte de toute
distraction. Placez les lampes de façon à ne pas travailler dans
l’ombre.
2. Assurez-vous que les personnes qui ne portent pas l'équipement
de sécurité approprié ne se trouvent pas à proximité de l'aire de
travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec.
Gardez les outils hors de la portée des enfants.
4. N'installez pas et n'utilisez pas d'outils électriques en présence de
gaz, de poussière ou de liquides inflammables.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection
personnelle homologué par l'Association canadienne de
normalisation (CSA) ou l'American National Standards Institute
(ANSI).
ÉQUIPEMENT DE PROTECTION PERSONNELLE
1. Portez toujours des lunettes antiprojections qui offrent une
protection frontale et latérale pour les yeux. L'équipement de
protection des yeux devrait être conforme à la norme CSA Z94.3-
07 ou ANSI Z87.1 fonction du type de travail effectué.
8843906 Perceuse pneumatique réversible à prise pistolet de 3/8 po V1,0
4 En cas de questions techniques, appelez le 1-800-665-8685
2. Portez un écran facial panoramique de type approprié avec les
lunettes de sécurité puisque cette tâche peut créer des copeaux,
des matières abrasives ou des particules.
3. Portez des gants qui protègent en fonction des matériaux de travail
et pour réduire les effets des vibrations de l'outil.
3.1 Ne portez pas de gants lorsque vous utilisez un outil dans
lequel le tissu pourrait demeurer coincé, entraînant ainsi la
main.
4. Portez des vêtements de protection conçus pour l'environnement
de travail et pour l'outil.
5. Les chaussures antidérapantes sont recommandées pour maintenir
la stabilité et l'équilibre au sein de l'environnement de travail.
6. Cet outil peut causer des dommages à l'ouïe. Portez un dispositif
de protection anti-bruit présentant une cote de réduction du bruit
adéquate en fonction du niveau de décibels.
7. L’outil peut être à haute pression. Portez des lunettes de sécurité et
des gants pour vous protéger au cours de l'opération. Gardez les
mains à l'écart des parties de caoutchouc exposées du tuyau.
PRÉCAUTIONS PERSONNELLES
Gardez le contrôle de l'outil, de vos mouvements et de l'environnement
de travail pour éviter les blessures ou le bris de l'outil.
1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,
d'alcool ou de médicaments.
2. Évitez de porter des vêtements ou des bijoux pouvant se prendre
dans les pièces mobiles d'un outil. Gardez les cheveux longs
recouverts ou attachés.
3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en
servir. Une stabilité et un équilibre appropriés sont nécessaires afin
d'avoir un meilleur contrôle en cas de situations inattendues.
4. Soutenez la pièce à travailler ou fixez-la sur une plate-forme stable.
Une pièce à travailler tenue dans les mains ou appuyée contre votre
corps sera instable et peut entraîner des blessures corporelles.
5. Gardez vos doigts à bonne distance de la gâchette/commutateur
lors du transport de loutil ou du branchement dun tuyau à air ou
d’un accessoire. Engagez le verrou de gâchette/interrupteur, le cas
échéant.
V1,0 Perceuse pneumatique réversible à prise pistolet de 3/8 po 8843906
Visitez www.princessauto.com pour plus d'informations 5
6. Évitez les mises en marche involontaires. Assurez-vous que le
régulateur/commutateur est en position neutre ou OFF (arrêt) lorsque
loutil nest pas utilisé et avant de le brancher à une source dair.
7. Des blessures graves ou même la mort peuvent survenir en cas
d’inhalation de lair comprimé. Le jet dair peut contenir du
monoxyde de carbone, des vapeurs toxiques ou des particules
solides. Ninhalez jamais lair comprimé provenant directement de
la pompe ou dun outil pneumatique.
CONSIGNES DE SÉCURITÉ SPÉCIFIQUES
AVERTISSEMENT! Ne permettez PAS au confort ou à votre
familiarisation avec l'outil (obtenus après un emploi répété) de
se substituer à une adhésion stricte aux règles de sécurité de
l'outil. Si vous utilisez cet outil de façon dangereuse ou
incorrecte, vous pouvez subir des blessures corporelles graves.
1. Utilisez le bon outil pour la tâche à effectuer. Cet outil a été conçu
pour une utilisation spécifique. Évitez de modifier ou d'altérer cet outil
ou de l'utiliser à une fin autre que celle pour laquelle il a été conçu.
2. N’utilisez pas loutil si des pièces présentent des dommages ou
sont déplacées. Réparez ou remplacez les pièces.
3. L'outil ne s'arrêtera pas immédiatement. Ne posez pas l'outil sur une
surface ou ne le laissez pas sans surveillance avant qu'il ne
s'immobilise. Une pièce mobile pourrait faire sauter l'outil ou s'agripper
à une surface et vous pourriez perdre la maîtrise de l'outil.
4. Assurez-vous toujours que la surface de travail est dépourvue de
clous ou autres objets étrangers.
5. Utilisez toujours le mandrin de taille appropriée. Si le mandrin est
plus grande que la tige de l'accessoire, elle ne pourra retenir la
tige correctement, ce qui pourrait entraîner des blessures pour
l'utilisateur, des dommages à l'outil ou à la pièce à travailler.
6. Vérifiez toujours si les lames sont endommagées avant chaque
utilisation. Les accessoires endommagés peuvent se casser
pendant l'utilisation et causer des blessures graves.
7. N'utilisez jamais des lames émoussés ni endommagés. Les
embouts affûtés doivent être manipulés avec soin. Les embouts
endommagés peuvent casser pendant leur utilisation. Les embouts
émoussés obligent à ce qu'on applique davantage de force au
niveau de l'outil, ce qui pourrait provoquer un bris de l'embout.
8843906 Perceuse pneumatique réversible à prise pistolet de 3/8 po V1,0
6 En cas de questions techniques, appelez le 1-800-665-8685
8. Maintenez fermement l'outil et placez le corps et les bras de façon
à vous permettre de résister à la force de l'effet de rebond. L'effet
de rebond propulse l'outil dans le sens opposé à celui du
mouvement de loutil, au moment de l'accrochage.
9. Utilisez des détecteurs de métal et des détecteurs de tension pour
repérer les conduites cachées d'électricité, d'eau ou de gaz. Évitez
de toucher les composants ou les conducteurs sous tension.
10. Avant de procéder au perçage, vérifiez s'il existe un jeu suffisant
pour le foret sous la pièce à travailler.
11. Si on vous interrompt alors que vous utilisez la perceuse,
complétez l'opération et placez celle-ci hors tension avant de
soulever le regard.
PRÉCAUTIONS RELATIVES AUX OUTILS
PNEUMATIQUES
1. Utilisez uniquement un air comprimé propre et sec comme source
d’énergie. Lair contaminé ou humide endommagera
progressivement loutil.
2. Installez une soupape d'arrêt ou un régulateur sur la conduite afin
de permettre une commande immédiate de l'alimentation en air, en
cas d'urgence, même si un tuyau se fend.
3. Arrêtez dutiliser loutil sil ne fonctionne pas correctement ou sil
présente des fuites dair. Attachez une étiquette sur loutil indiquant
quil est « défectueux » ou quil est « hors service », jusquà ce quil
soit réparé.
4. Consultez la pression nominale maximale du fabricant en ce qui
concerne les outils pneumatiques et accessoires. La pression de
sortie du compresseur doit être réglée de façon à ne jamais
dépasser la pression nominale maximale de l'outil (consultez
Spécifications). Si on dépasse la pression nominale maximale, il
pourrait en résulter un risque dexplosion capable dentraîner des
blessures et des dommages aux biens.
5. Avant de relier lalimentation en air, fixez correctement tous les
accessoires sur loutil. Un accessoire mal attaché pourrait se
détacher et se briser durant lutilisation.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

PROPOINT 8843906 Le manuel du propriétaire

Catégorie
Outils électroportatifs
Taper
Le manuel du propriétaire

dans d''autres langues