Powerfist 9007824 Le manuel du propriétaire

Marque: Powerfist

Modèle: 9007824

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

V1.0 9007824

Please read and understand all instructions before use. Retain this manual for

future reference.

This page is intentionally left blank.

SPECIFICATIONS

Air Inlet 1/4 in.

Thread Type NPTF

Pressure Range 0 to 90 PSI

Average CFM @ 15 Second Run Time 4 CFM

CFM @ Full Load 4 CFM

Speed Rating 12,000 RPM

Torque Range 0 to 1,060 in.-lb

Min. Hose Size 3/8 in.

Overall Length 6-1/2 in.

Handle Type Pistol

Handle Material Aluminum

INTRODUCTION

The air screwdriver is ideal to quickly tighten and loosen fasteners when

tackling a large project.

SAFETY

WARNING! Read and understand all instructions before using this tool.

The operator must follow basic precautions to reduce the risk of

personal injury and/or damage to the equipment.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or death

if certain instructions are not followed.

DANGER! This notice indicates an immediate and specic hazard that will result in severe

personal injury or death if the proper precautions are not taken.

WARNING! This notice indicates a specic hazard or unsafe practice that could result in a

serious injury if the proper precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may result in minor

or moderate injury if proper practices are not taken.

NOTICE! This notice indicates that a specic hazard or unsafe practice will result in

equipment or property damage, but not personal injury.

V1.0 PISTOL-GRIP AIR SCREWDRIVER 9007824

Page 3 www.princessauto.com / 1-800-665-8685

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit

and free of distractions. Place lights so you are not working in a shadow.

2. Keep anyone not wearing the appropriate safety equipment away from

the work area.

3. Store unused tools properly in a dry, safe and secure location to prevent

rust, damage or misuse.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the

Canadian Standards Association (CSA) or American National Standards

Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

1. Always wear impact safety goggles that provide front and side protection

for the eyes. Eye protection equipment should comply with CSA Z94.3-07

or ANSI Z87.1 standards based on the type of work performed.

2. The tool may contain high pressure. Use safety glasses and gloves for

protection during operation. Keep hands clear of the exposed rubber

portions of the hose.

3. Wear the appropriate type of full-face shield in addition to safety googles,

as the work can create chips, abrasive or particulate matter.

4. Wear protective clothing designed for the work environment and tool.

5. The air source used with this tool may cause hearing damage. Wear ear

protection gear to eliminate or reduce the noise.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the inuence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

9007824 PISTOL-GRIP AIR SCREWDRIVER V1.0

www.princessauto.com / 1-800-665-8685 Page 4

4. Keep your ngers away from the trigger/switch while carrying the tool,

attaching an air hose or an accessory. Lock the trigger/switch safety if

available.

5. Avoid unintentional starts. Be sure that the regulator/throttle switch is in

the neutral or OFF position when not in use and before connecting it to

any air source.

6. Never point the air stream or tool at any point of your body, other people

or animals. Debris and dust ejected at high speed can cause an injury.

7. Serious injury or death may occur from inhaling compressed air. The air

stream may contain carbon monoxide, toxic vapors or solid particles.

Never inhale compressed air directly from the pump or air tool.

SPECIFIC SAFETY

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specic

function. Do not modify or alter this tool or use it for an unintended

purpose.

2. Do not use the tool if any parts are damage broken or misplaced. Repair or

replace the parts.

3. Hold the tool correctly; be ready to counteract normal or sudden

movements and have both hands available.

4. The tool is not insulated against contact with live electrical conduits or

sources.

POWER TOOL PRECAUTIONS

1. Do not use any power tool with a malfunctioning power switch or control.

A power tool that fails to respond to the controls is dangerous and can

cause an injury. A qualied technician must repair and verify the power

tool is operating correctly, before it can be used.

2. Disconnect the power source before installing or servicing the

screwdriver.

3. Never force the screwdriver. Excessive pressure could break the tool,

resulting in damage to your workpiece or serious personal injury.

Excessive pressure is the cause if your tool runs smoothly under no load,

but roughly under load.

V1.0 PISTOL-GRIP AIR SCREWDRIVER 9007824

Page 5 www.princessauto.com / 1-800-665-8685

4. Keep hands and ngers away from the work area. Any part of body

contacting the screwdriver's working parts could cause an injury.

5. Do not touch an operating motor. Motors can operate at high

temperatures and can cause a burn injury.

6. The material and the motor housing can get very hot during operation.

Stop work until the screwdriver and the driver bit both cool down to a

safe temperature.

7. Do not cover the air vents. Proper cooling of the motor is necessary to

ensure normal life of the tool.

8. Avoid unintentional starts. Be sure that the regulator/throttle switch is in

the neutral or OFF position when not in use and before connecting it to

any air source.

AIR TOOL PRECAUTIONS

1. Use only clean and dry compressed air as a power source. Contaminated

or moist air will gradually damage the tool.

2. Install an in-line shuto valve or regulator to allow immediate control over

the air supply in an emergency, even if a hose is ruptured.

3. Discontinue tool use if it does not work properly or air is leaking. Tag or

mark the tool as ‘defective’ or ‘out of service’ until repaired.

4. Check the manufacturer’s maximum pressure rating for air tools and

accessories. Compressor outlet pressure must be regulated to never

exceed the maximum pressure rating of the tool (see Specications).

Exceeding the maximum PSI rating can create a bursting hazard, causing

injury and property damage.

5. Attach all accessories properly to the tool before connecting the air

supply. A loose accessory may detach or break during operation.

6. Never use oxygen, combustible gas or any other bottled gas as a power

source. Any power source other than an air compressor could cause an

explosion and serious personal injury.

7. Turn OFF the valve and discharge any remaining air pressure after each

use or before adjusting the tool.

8. Do not leave the air tool unattended with its compressed air supply on.

Turn o the compressed air supply and bleed the air tool of any remaining

compressed air before leaving the air tool unattended.

9007824 PISTOL-GRIP AIR SCREWDRIVER V1.0

www.princessauto.com / 1-800-665-8685 Page 6

9. Serious injury may occur from loose debris being propelled at high speeds

from the compressed air stream. Always wear OSHA approved safety

glasses to protect the eyes during operation of the air compressor.

10. Always turn o the air compressor and drain tank pressure completely

before attempting maintenance or attaching air tools. Release pressure

slowly from the system.

11. Do not cover the air vents.

AIR HOSE PRECAUTIONS

1. Inspect the tool's air hose for cracks, fraying or other faults before each

use. Discontinue use if the air hose is damaged or hissing is heard from

the air hose or couplers. Replace the defective air hose.

2. Do not allow people, mobile equipment or vehicles to pass over the

unprotected air hose. Position the air hose away from high trac areas, in

a reinforced conduit or place planks on both sides of the air hose to create

a protective trench.

3. Prevent damage to the air hose by observing the following:

a. Never carry the tool by the air hose.

b. Keep the air hose behind the tool and out of the tool's work path.

c. Keep the air hose away from heat, oil, sharp edges or moving parts.

d. Do not wrap the air hose around the tool as sharp edges may pierce

or crack the air hose. Gently coil the hose and either hang on a hook

or fasten with a device to keep hose together when storing.

4. A damaged or disconnected air hose under pressure may whip around and

inict personal injury or damage the work area. Secure the compressor's

air hose to a xed or permanent structure with clamps or cable ties.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a

malfunction and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Contents:

• Air Screwdriver • M-style plug

V1.0 PISTOL-GRIP AIR SCREWDRIVER 9007824

Page 7 www.princessauto.com / 1-800-665-8685

• Double-ended Phillips

bit

• Hanging loop

• Air Regulator

• Bushing

IDENTIFICATION KEY

A. Collet

B. Hang Ring (not shown)

C. Air Screwdriver

D. Trigger

E. Air Inlet

F. Air Exhaust

G. Air Regulator

H. Dual Screwdriver Bit

I. Male Air Plug

J. Bushing

ASSEMBLY & INSTALLATION

1. Attach the hang ring through the hole in

the tool's upper body.

2. Remove the protective cap when you are

ready to install the air plug.

3. Turn the air regulator knob fully in either

direction to seal the regulator in the o

position.

4. Wrap the external threads of the air

regulator with sealant tape. Leave the leading threads unwrapped.

5. Screw the air regulator into the tool's air inlet and tighten with a wrench

until snug.

INSTALL AIR COUPLER PLUG

Prepare a standard 1/4 in. NPT coupler plug (included) for use with your tool.

Fig. 1

9007824 PISTOL-GRIP AIR SCREWDRIVER V1.0

www.princessauto.com / 1-800-665-8685 Page 8

1. Wrap the external threads of the air regulator with sealant tape. Leave the

leading threads unwrapped.

a. Wrap tape in a clockwise direction so it will not unravel.

b. Do not tape all the threads. Leave several leading threads unwrapped

for easier alignment.

2. Screw the coupler plug into the air regulator until snug. Tighten with a

wrench if necessary.

3. Run the compressor at a low volume and check the connection for air

leaks. Do not use the tool until all air leaks are repaired or the faulty

component is replaced.

IMPORTANT! Vibration may cause failure if a quick coupler is connected

directly to the air tool. To overcome this, connect a leader hose to the

tool. A quick coupler may then be used to connect the leader hose to the

air line hose.

OPERATIONS

WARNING! Immediately release the trigger if the tool's bit becomes

stuck or jammed. The tool’s torque can twist your arm and cause an

injury. The tool may twist out of your grip and cause an injury to

yourself or a bystander.

IMPORTANT! Only use an accessory that exceeds the Speed rating (see

Specications).

1. Pull the collet backwards towards the

tool.

2. Insert the dual screwdriver bit into the

collet, then release the cap to allow it to

snap back and lock the bit into position.

• You can install a regular drill bit by

inserting the bushing into the collet,

then inserting the drill bit into the

bushing.

3. Pull on the screwdriver bit to make sure it is locked in place.

4. Attach the air hose from the air source to the tool's air coupler plug.

5. Twist the air regulator knob to allow air to ow.

Fig. 2

V1.0 PISTOL-GRIP AIR SCREWDRIVER 9007824

Page 9 www.princessauto.com / 1-800-665-8685

6. Before using the tool on a workpiece, test the tool by running it at the

highest speed rating for at least 30 seconds in a safe position. Stop

immediately if there is any abnormal vibration or wobbling. Check the tool

to determine the cause.

7. Insert the screwdriver bit into the screw.

8. Always hold the tool rmly in your hands before switching the tool ON.

The reaction to the motor’s torque may cause the tool to twist, as it

accelerates to full speed.

9. Squeeze the trigger to allow the air to ow.

a. Squeeze the lower part of the trigger (L) and the bit will rotate

clockwise.

b. Squeeze the upper part of the trigger (R) and the bit will rotate

counterclockwise.

10. Apply power in bursts to avoid stripping the screw head.

11. When nished with the tool, turn o the air compressor, disconnect the

air hose and discharge any residual air remaining in the tool.

PRESSURE DROP

Apply the air consumption and pressure rate numbers to the tool’s air inlet, not

the compressor’s outlet. Calculate the pressure drop for your air supply set-up

and increase the compressor outlet pressure to compensate. Make sure you do

not exceed the maximum pressure for any part of your air supply system.

Installing a pressure gauge at the tool inlet is the best way to measure the air

pressure and adjust the compressor’s output.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is ecient, easier to

control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace damaged or

worn components.. Only use identical replacement parts when servicing.

3. Only use accessories intended for use with this tool. Follow instructions

for changing accessories.

4. Keep the tool handles or gripping surfaces clean and dry.

5. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

9007824 PISTOL-GRIP AIR SCREWDRIVER V1.0

www.princessauto.com / 1-800-665-8685 Page 10

WARNING! Only qualied service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

AIR TOOL LUBRICATION

NOTICE! Only use air tool oil to lubricate the tool. Other lubricants are

not suitable and will damage the tool or cause a malfunction during use.

NOTICE! Never use a penetrating oil to lubricate an air tool. Penetrating

oil acts as a solvent that will dissolve the tool’s grease packing and may

damage the o-rings, causing the tool to seize or malfunction.

1. All air tools have an internal coating of grease to prevent corrosion during

shipping and storage. Remove this grease by adding a generous amount of

air tool oil in the air inlet and then run the tool under no load until the

exhaust is clear.

2. Manually add a drop or two of air tool oil into the tool’s coupler plug

before each use and after every hour of continuous use. The tool will not

work properly without lubrication and parts will wear prematurely.

3. Avoid adding too much air tool oil as this can cause premature power loss

and eventual tool failure. A qualied technician will need to take the tool

apart and clean out the excess oil.

4. Apply a generous amount of air tool oil to the tool before storing it for an

extended period of time (overnight, weekend, etc.). Run the tool for

approximately 30 seconds to ensure the oil is evenly distributed

throughout the tool. Store it in a clean and dry location.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualied technician

service the tool.

V1.0 PISTOL-GRIP AIR SCREWDRIVER 9007824

Page 11 www.princessauto.com / 1-800-665-8685

Problem(s) Possible Cause(s) Suggested Solution(s)

Tool runs at normal

speed, but loses

power under load.

1. Motor parts worn. 1. Have a qualied technician service

the tool.

2. Replace tool or parts.

Tool runs slowly.

Air ows slightly

from exhaust.

And/Or

Air ows slightly

from nozzle.

1. Motor parts jammed

with dirt particles.

Airow blocked by

dirt.

2. Air regulator in closed

position.

3. Damage or excessive

wearing of internal

parts.

1. Check air inlet lter for blockage.

a. Pour air tool lubricating oil into

air inlet as per lubrication

instructions for clearing

shipping grease.

b. Operate tool in short bursts to

clear debris.

c. If tool still jammed, clean tool

and lubricate per lubrication

instructions.

2. Open the air regulator to desired

airow.

3. Have a qualied technician service

the tool.

a. Replace tool or parts.

Tools will not run.

Air ows freely

from exhaust.

1. Damage or excessive

wearing of internal

parts.

1. Have a qualied technician service

the tool.

2. Replace tool or parts.

Tool will not shut

o.

1. Throttle valve o-ring

dislodged from inlet

valve seat.

2. Trigger mechanism

jammed or dirty.

1. Replace throttle valve o-rings.

2. Clean trigger mechanism and

lubricate.

Loss of power or

erratic

performance.

1. Excessive drain on the

air hose. Incorrect size

or type of hose

connectors.

2. Moisture or restriction

in the air hose/tank

3. Air compressor has

insucient ow.

1. Check the air hose and conrm the

hose tting is correct for the inlet

bushing.

2. Depressurize system and drain tank

and air hose of water.

3. Ensure tool is connected to a

compressor with a rate ow that

matches the tool.

9007824 PISTOL-GRIP AIR SCREWDRIVER V1.0

www.princessauto.com / 1-800-665-8685 Page 12

PARTS BREAKDOWN

PARTS LIST

#DESCRIPTION QTY

1 C-ring 2

2 Lock set liner 2

3 Bit Collet 1

4 Spring 1

5 Screw 3

6 Washer 3

7 Front Cover 1

8 Gasket 1

9 Bushing 1

10 Spacer 1

11 Bushing 1

12 Steel Ball 2

13 Work Spindle 1

14 Set Pin 2

15 Hammer Case 1

16 Hammer Dog 2

17 Washer 1

V1.0 PISTOL-GRIP AIR SCREWDRIVER 9007824

Page 13 www.princessauto.com / 1-800-665-8685

18 Cam 1

19 Lock Ring 1

20 Bearing 1

21 Front Plate 1

22 Rotor 1

23 Rotor Blade 6

24 Cylinder 1

25 Rear Plate 1

26 Set Pin 1

27 Set Pin 1

28 Bearing 1

29 Gasket 1

30 Hang Ring 1

31 Main Housing 1

32 Set Pin 1

33 Set Pin 1

34 Air Inlet 1

35 Soft Grip 1

36 Muer 1

37 O-Ring 1

38 Screw 1

39 Liner 1

40 Spring 2

41 Steel Ball 2

42 O-Ring 2

43 Valve Stem 2

44 Valve 2

45 Trigger 1

9007824 PISTOL-GRIP AIR SCREWDRIVER V1.0

www.princessauto.com / 1-800-665-8685 Page 14

This page is intentionally left blank.

V1,0 9007824

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.

Conservez ce manuel afin de pouvoir le consulter plus tard.

Cette page a été laissée blanche intentionnellement.

SPÉCIFICATIONS

Entrée d’air 1/4 po

Type de letage NPTF

Plage de pression 0 à 90 lb/po carré

Débit moyen à un temps de fonctionnement de 15 secondes 4 pi cubes/min

Débit à pleine charge 4 pi cubes/min

Vitesse nominale 12 000 tr / min

Plage de couple 0 à 1 060 po-lb

Diamètre min. de tuyau 3/8 po

Longueur hors tout 6 1/2 po

Type de manche Pistolet

Matériau de manche Aluminium

INTRODUCTION

Le tournevis à air comprimé est idéal pour serrer et desserrer rapidement les

xations lors de projets d’envergure.

SÉCURITÉ

AVERTISSEMENT! Veuillez lire et comprendre toutes les instructions

avant d’utiliser cet outil. L’opérateur doit respecter les précautions

élémentaires pour réduire le risque de blessure corporelle ou de

dommage à l’équipement.

DÉFINITIONS DE DANGER

Veuillez vous familiariser avec les avis de danger qui sont présentés dans ce

manuel. Un avis est une alerte indiquant qu’il existe un risque de dommage

matériel, de blessure ou de mort si on ne respecte pas certaines instructions.

DANGER! Cet avis indique un risque immédiat et particulier qui entraînera des

blessures corporelles graves ou même la mort si on omet de prendre les

précautions nécessaires.

AVERTISSEMENT! Cet avis indique un risque particulier ou une pratique non sécuritaire qui

pourrait entraîner des blessures graves si on omet de prendre les

précautions nécessaires.

V1.0 TOURNEVIS À AIR COMPRIMÉ À PRISE PISTOLET 9007824

Page 3 www.princessauto.com / 1-800-665-8685

ATTENTION! Cet avis indique une situation possiblement dangereuse qui peut

entraîner des blessures mineures ou modérées si on ne procède pas de la

façon recommandée.

AVIS! Cet avis indique un risque particulier ou une pratique non sécuritaire qui

entraînera des dommages au niveau de l’équipement ou des biens, mais

non des blessures corporelles.

AIRE DE TRAVAIL

1. Travaillez dans un environnement de travail sécuritaire. Gardez votre aire

de travail propre, bien éclairée et exempte de toute distraction. Placez les

lampes de façon à ne pas travailler dans l’ombre.

2. Assurez-vous que les personnes qui ne portent pas l’équipement de

sécurité approprié ne se trouvent pas à proximité de l’aire de travail.

3. Rangez les outils inutilisés correctement dans un lieu sécurisé et sec pour

empêcher la rouille, les dommages ou un mauvais usage.

SÉCURITÉ PERSONNELLE

AVERTISSEMENT! Portez de l’équipement de protection individuelle

homologué par l’Association canadienne de normalisation (CSA) ou

l’American National Standards Institute (ANSI).

ÉQUIPEMENT DE PROTECTION INDIVIDUELLE

AVERTISSEMENT! Portez de l’équipement de protection individuelle homologué

par l’Association canadienne de normalisation (CSA) ou l’American National

Standards Institute (ANSI).

1. Portez toujours des lunettes antiprojections qui orent une protection

frontale et latérale pour les yeux. L’équipement de protection des yeux

devrait être conforme à la norme CSA Z94.3-07 ou ANSI Z87.1 en fonction

du type de travail eectué.

2. L’outil peut être à haute pression. Portez des lunettes de sécurité et des

gants pour vous protéger au cours de l'opération. Gardez les mains à

l'écart des parties de caoutchouc exposées du tuyau.

3. Portez un écran facial panoramique de type approprié avec les lunettes de

sécurité puisque cette tâche peut créer des copeaux, des matières

abrasives ou des particules.

4. Portez des vêtements de protection conçus pour l'environnement de

travail et pour l'outil.

5. La source d’air utilisée avec cet outil peut causer des dommages auditifs.

Portez une protection d’oreille an d’éliminer ou de réduire le bruit.

9007824 TOURNEVIS À AIR COMPRIMÉ À PRISE PISTOLET V1.0

www.princessauto.com / 1-800-665-8685 Page 4

La page est en cours de chargement...

Powerfist 9007824 Le manuel du propriétaire

Marque: Powerfist

Modèle: 9007824

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Powerfist 9007824 Owner's manual

Powerfist 9007824 Le manuel du propriétaire

Powerfist 9007824 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents