Power Fist 9007816 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
V1.0 9007816
Please read and understand all instructions before use. Retain this manual for
future reference.
This page is intentionally left blank.
SPECIFICATIONS
Air Inlet 1/4 in.
Thread Type NPTF
Pressure Range 0 to 90 PSI
Average CFM @ 15 Second Run Time 4.5 CFM
CFM @ Full Load 4.5 CFM
Speed Rating 9,000 RPM
Torque Range 0 to 480 in.-lb
Min. Hose Size 3/8 in.
Overall Length 7 in.
Handle Type Straight
Handle Material Aluminum
INTRODUCTION
The air screwdriver is ideal to quickly tighten and loosen fasteners when
tackling a large project. It features a forward/reverse switch and an air
regulator to control the chuck's speed.
SAFETY
WARNING! Read and understand all instructions before using this tool.
The operator must follow basic precautions to reduce the risk of
personal injury and/or damage to the equipment.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A
notice is an alert that there is a possibility of property damage, injury or death
if certain instructions are not followed.
DANGER! This notice indicates an immediate and specic hazard that will result in severe
personal injury or death if the proper precautions are not taken.
WARNING! This notice indicates a specic hazard or unsafe practice that could result in a
serious injury if the proper precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that may result in minor
or moderate injury if proper practices are not taken.
NOTICE! This notice indicates that a specic hazard or unsafe practice will result in
equipment or property damage, but not personal injury.
V1.0 STRAIGHT-GRIP AIR SCREWDRIVER 9007816
Page 3 www.princessauto.com / 1-800-665-8685
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-lit
and free of distractions. Place lights so you are not working in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from
the work area.
3. Store unused tools properly in a dry, safe and secure location to prevent
rust, damage or misuse.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the
Canadian Standards Association (CSA) or American National Standards
Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
WARNING! Wear personal protective equipment approved by the Canadian
Standards Association (CSA) or American National Standards Institute (ANSI).
1. Always wear impact safety goggles that provide front and side protection
for the eyes. Eye protection equipment should comply with CSA Z94.3-07
or ANSI Z87.1 standards based on the type of work performed.
2. The tool may contain high pressure. Use safety glasses and gloves for
protection during operation. Keep hands clear of the exposed rubber
portions of the hose.
3. Wear the appropriate type of full-face shield in addition to safety googles,
as the work can create chips, abrasive or particulate matter.
4. Wear protective clothing designed for the work environment and tool.
5. The air source used with this tool may cause hearing damage. Wear ear
protection gear to eliminate or reduce the noise.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the inuence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the
moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and balance
enables better control in unexpected situations.
9007816 STRAIGHT-GRIP AIR SCREWDRIVER V1.0
www.princessauto.com / 1-800-665-8685 Page 4
4. Keep your ngers away from the trigger/switch while carrying the tool,
attaching an air hose or an accessory. Lock the trigger/switch safety if
available.
5. Avoid unintentional starts. Be sure that the regulator/throttle switch is in
the neutral or OFF position when not in use and before connecting it to
any air source.
6. Never point the air stream or tool at any point of your body, other people
or animals. Debris and dust ejected at high speed can cause an injury.
7. Serious injury or death may occur from inhaling compressed air. The air
stream may contain carbon monoxide, toxic vapors or solid particles.
Never inhale compressed air directly from the pump or air tool.
SPECIFIC SAFETY
WARNING! DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to the tool safety rules. If you use
this tool unsafely or incorrectly, you can suer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a specic
function. Do not modify or alter this tool or use it for an unintended
purpose.
2. Do not use the tool if any parts are damage broken or misplaced. Repair or
replace the parts.
3. Hold the tool correctly; be ready to counteract normal or sudden
movements and have both hands available.
4. The tool is not insulated against contact with live electrical conduits or
sources.
POWER TOOL PRECAUTIONS
1. Do not use any power tool with a malfunctioning power switch or control.
A power tool that fails to respond to the controls is dangerous and can
cause an injury. A qualied technician must repair and verify the power
tool is operating correctly, before it can be used.
2. Disconnect the power source before installing or servicing the tool.
3. Never force the tool. Excessive pressure could break the tool, resulting in
damage to your workpiece or serious personal injury. Excessive pressure
is the cause if your tool runs smoothly under no load, but roughly under
load.
4. Keep hands and ngers away from the work area. Any part of body
contacting the tool’s working parts could cause an injury.
V1.0 STRAIGHT-GRIP AIR SCREWDRIVER 9007816
Page 5 www.princessauto.com / 1-800-665-8685
5. Only use accessories that are specically designed for use with the tool.
Ensure the accessory is tightly installed.
6. Only use an accessory that exceeds the Speed rating (see Specications)
7. Before using the tool on a workpiece, test the tool by running it at the
highest speed rating for at least 30 seconds in a safe position. Stop
immediately if there is any abnormal vibration or wobbling. Check the tool
to determine the cause.
8. Never touch the tool accessory or workpiece during or immediately after
use. They may be hot and could inict a burn injury.
9. Never use a tool with a cracked or worn tool accessory. Change the tool
accessory before using it.
10. Do not place the tool down until the tool’s accessory has stopped moving.
The accessory may catch the surface of work material and wrench itself
free, causing injury to the user or others in the work area.
AIR TOOL PRECAUTIONS
1. Use only clean and dry compressed air as a power source. Contaminated
or moist air will gradually damage the tool.
2. Install an in-line shuto valve or regulator to allow immediate control over
the air supply in an emergency, even if a hose is ruptured.
3. Discontinue tool use if it does not work properly or air is leaking. Tag or
mark the tool as ‘defective’ or ‘out of service’ until repaired.
4. Check the manufacturer’s maximum pressure rating for air tools and
accessories. Compressor outlet pressure must be regulated to never
exceed the maximum pressure rating of the tool (see Specications).
Exceeding the maximum PSI rating can create a bursting hazard, causing
injury and property damage.
5. Attach all accessories properly to the tool before connecting the air
supply. A loose accessory may detach or break during operation.
6. Never use oxygen, combustible gas or any other bottled gas as a power
source. Any power source other than an air compressor could cause an
explosion and serious personal injury.
7. Turn OFF the valve and discharge any remaining air pressure after each
use or before adjusting the tool.
8. Do not leave the air tool unattended with its compressed air supply on.
Turn o the compressed air supply and bleed the air tool of any remaining
compressed air before leaving the air tool unattended.
9007816 STRAIGHT-GRIP AIR SCREWDRIVER V1.0
www.princessauto.com / 1-800-665-8685 Page 6
9. Serious injury may occur from loose debris being propelled at high speeds
from the compressed air stream. Always wear OSHA approved safety
glasses to protect the eyes during operation of the air compressor.
10. Always turn o the air compressor and drain tank pressure completely
before attempting maintenance or attaching air tools. Release pressure
slowly from the system.
11. Do not cover the air vents.
AIR HOSE PRECAUTIONS
1. Inspect the tool's air hose for cracks, fraying or other faults before each
use. Discontinue use if the air hose is damaged or hissing is heard from
the air hose or couplers. Replace the defective air hose.
2. Do not allow people, mobile equipment or vehicles to pass over the
unprotected air hose. Position the air hose away from high trac areas, in
a reinforced conduit or place planks on both sides of the air hose to create
a protective trench.
3. Prevent damage to the air hose by observing the following:
a. Never carry the tool by the air hose.
b. Keep the air hose behind the tool and out of the tool's work path.
c. Keep the air hose away from heat, oil, sharp edges or moving parts.
d. Do not wrap the air hose around the tool as sharp edges may pierce
or crack the air hose. Gently coil the hose and either hang on a hook
or fasten with a device to keep hose together when storing.
4. A damaged or disconnected hydraulic hose under pressure may whip
around and inict personal injury or damage the work area. Secure the
hose to a xed or permanent structure with clamps or cable ties.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a
malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
Contents:
• Air Screwdriver • M-style plug
V1.0 STRAIGHT-GRIP AIR SCREWDRIVER 9007816
Page 7 www.princessauto.com / 1-800-665-8685
• Double-ended Phillips bit • Hanging loop
IDENTIFICATION KEY
A. Locking Chuck
B. Air Exhaust
C. Trigger
D. Air Regulator
E. Hang Ring
F. Spindle Opening
G. Air Screwdriver
H. Forward/Reverse Switch
I. Air Inlet
J. Male Air Plug (not shown)
K. Dual Screwdriver Bit (not shown)
ASSEMBLY & INSTALLATION
1. Attach the hang ring to the air inlet. Spread and hold the ring apart and
insert the ends into the indents on the air inlet collar. The hang ring will
snap back into shape, holding the ends in position.
2. Remove the protective cap when you are ready to install the air plug.
INSTALL AIR COUPLER PLUG
Prepare a standard 1/4 in. NPT coupler plug (included) for use with your tool.
1. Wrap the external threads of the coupler plug with sealant tape.
a. Wrap tape in a clockwise direction so it will not unravel.
b. Do not tape all the threads. Leave several leading threads unwrapped
for easier alignment.
2. Screw the coupler plug into the tool's air inlet and tighten with a wrench
until snug.
3. Run the compressor at a low volume and check the connection for air
leaks. Do not use the tool until all air leaks are repaired or the faulty
component is replaced.
9007816 STRAIGHT-GRIP AIR SCREWDRIVER V1.0
www.princessauto.com / 1-800-665-8685 Page 8
IMPORTANT! Vibration may cause failure if a quick coupler is connected
directly to the air tool. To overcome this, connect a leader hose to the
tool. A quick coupler may then be used to connect the leader hose to the
air line hose.
OPERATIONS
WARNING! Immediately release the trigger if the tool's bit becomes
stuck or jammed. The tool’s torque can twist your arm and cause an
injury. The tool may twist out of your grip and cause an injury to
yourself or a bystander.
IMPORTANT! Only use an accessory that exceeds the Speed rating (see
Specications).
1. Push the locking chuck's set cap away from the tool.
2. Insert the screwdriver bit into the chuck, then release the cap to allow it
to snap back and lock the bit into position.
3. Pull on the screwdriver bit to make sure it is locked in place.
4. Attach the air hose from the air source to the tool's air coupler plug.
5. Before using the tool on a workpiece, test the tool by running it at the
highest speed rating for at least 30 seconds in a safe position. Stop
immediately if there is any abnormal vibration or wobbling. Check the tool
to determine the cause.
6. Move the forward/reverse switch on the bottom left (L) and the chuck will
rotate clockwise. Move the switch right (R) and the chuck will rotate
counterclockwise.
7. Choose the chuck speed by aligning the numbers on the air regulator with
the arrow on the side of the tool. Setting 1 is the highest speed. Lower the
speed by selecting setting 2 or 3.
8. Insert the screwdriver bit into the screw.
9. Always hold the tool rmly in your hands before switching the tool ON.
The reaction to the motor’s torque may cause the tool to twist, as it
accelerates to full speed.
10. Squeeze the trigger to allow the air to ow.
11. Apply power in bursts to avoid stripping the screw head.
V1.0 STRAIGHT-GRIP AIR SCREWDRIVER 9007816
Page 9 www.princessauto.com / 1-800-665-8685
12. Change the screw bit as needed by pulling the set cap forward to remove
the bit and insert a new one.
13. When nished with the tool, turn o the air compressor, disconnect the
air hose and discharge any residual air remaining in the tool.
PRESSURE DROP
Apply the air consumption and pressure rate numbers to the tool’s air inlet, not
the compressor’s outlet. Calculate the pressure drop for your air supply set-up
and increase the compressor outlet pressure to compensate. Make sure you do
not exceed the maximum pressure for any part of your air supply system.
Installing a pressure gauge at the tool inlet is the best way to measure the air
pressure and adjust the compressor’s output.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is ecient, easier to
control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace damaged or
worn components.. Only use identical replacement parts when servicing.
3. Only use accessories intended for use with this tool. Follow instructions
for changing accessories.
4. Keep the tool handles or gripping surfaces clean and dry.
5. Maintain the tool’s labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd. for
replacements.
WARNING! Only qualied service personnel should repair the tool. An
improperly repaired tool may present a hazard to the user and/or others.
AIR TOOL LUBRICATION
NOTICE! Only use air tool oil to lubricate the tool. Other lubricants are
not suitable and will damage the tool or cause a malfunction during use.
NOTICE! Never use a penetrating oil to lubricate an air tool. Penetrating
oil acts as a solvent that will dissolve the tool’s grease packing and may
damage the o-rings, causing the tool to seize or malfunction.
1. All air tools have an internal coating of grease to prevent corrosion during
shipping and storage. Remove this grease by adding a generous amount of
9007816 STRAIGHT-GRIP AIR SCREWDRIVER V1.0
www.princessauto.com / 1-800-665-8685 Page 10
air tool oil in the air inlet and then run the tool under no load until the
exhaust is clear.
2. Manually add a drop or two of air tool oil into the tool’s coupler plug
before each use and after every hour of continuous use. The tool will not
work properly without lubrication and parts will wear prematurely.
3. Avoid adding too much air tool oil as this can cause premature power loss
and eventual tool failure. A qualied technician will need to take the tool
apart and clean out the excess oil.
4. Apply a generous amount of air tool oil to the tool before storing it for an
extended period of time (overnight, weekend, etc.). Run the tool for
approximately 30 seconds to ensure the oil is evenly distributed
throughout the tool. Store it in a clean and dry location.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function
properly or parts are missing. If unable to do so, have a qualied technician
service the tool.
Problem(s) Possible Cause(s) Suggested Solution(s)
Tool runs at normal
speed, but loses
power under load.
1. Motor parts worn. 1. Have a qualied technician service
the tool.
2. Replace tool or parts.
V1.0 STRAIGHT-GRIP AIR SCREWDRIVER 9007816
Page 11 www.princessauto.com / 1-800-665-8685
Problem(s) Possible Cause(s) Suggested Solution(s)
Tool runs slowly.
Air ows slightly
from exhaust.
And/Or
Air ows slightly
from nozzle.
1. Motor parts jammed
with dirt particles.
OR
Airow blocked by
dirt.
2. Air regulator in closed
position.
3. Damage or excessive
wearing of internal
parts.
1. Check air inlet lter for blockage.
a. Pour air tool lubricating oil into
air inlet as per lubrication
instructions for clearing
shipping grease.
b. Operate tool in short bursts to
clear debris.
c. If tool still jammed, clean tool
and lubricate per lubrication
instructions.
2. Open the air regulator to desired
airow.
3. Have a qualied technician service
the tool.
a. Replace tool or parts.
Tools will not run.
Air ows freely
from exhaust.
1. Damage or excessive
wearing of internal
parts.
1. Have a qualied technician service
the tool.
2. Replace tool or parts.
Tool will not shut
o.
1. Throttle valve o-ring
dislodged from inlet
valve seat.
2. Trigger mechanism
jammed or dirty.
1. Replace throttle valve o-rings.
2. Clean trigger mechanism and
lubricate.
Loss of power or
erratic
performance.
1. Excessive drain on the
air hose. Incorrect size
or type of hose
connectors.
2. Moisture or restriction
in the air hose/tank
3. Air compressor has
insucient ow.
1. Check the air hose and conrm the
hose tting is correct for the inlet
bushing.
2. Depressurize system and drain tank
and air hose of water.
3. Ensure tool is connected to a
compressor with a rate ow that
matches the tool.
9007816 STRAIGHT-GRIP AIR SCREWDRIVER V1.0
www.princessauto.com / 1-800-665-8685 Page 12
PARTS BREAKDOWN
PARTS LIST
# DESCRIPTION QTY
1 Housing 1
2 Gasket 1
3 Bearing 1
4 Rear Plate 1
5 Rotor 1
6 Rotor Blade 6
7 Pin 1
8 Pin 2
9 Cylinder 1
10 Front Plate 1
11 Pin 1
12 Bearing 1
13 Set Ring 1
14 Cushion 1
15 Cam 1
16 Hammer Case 1
17 Hammer Dog 2
18 Work Spindle 1
19 Set Pin 2
20 Steel Ball 1
21 Bushing 1
22 Gasket 1
23 Bushing 1
24 O-ring 1
25 Decoration Ring 1
26 Front Cover 1
27 Circlip 1
28 Set Cap 1
29 Spring 1
30 Spacer 1
31 Ring 1
V1.0 STRAIGHT-GRIP AIR SCREWDRIVER 9007816
Page 13 www.princessauto.com / 1-800-665-8685
32 Valve Seat 1
33 O-Ring 3
34 O-Ring 1
35 Valve Stem 1
36 Spring 1
37 O-Ring 1
38 Nut 1
39 Forward/Reverse Switch 1
40 Air Regulator 1
41 O-Ring 1
42 Spring 2
43 Steel Ball 2
44 O-Ring 1
45 Air Inlet 1
46 Screw 1
47 Pin 1
48 Trigger 1
49 Hang Ring 1
50 Pin 1
51 Air Coupler Plug 1
52 Screwdriver Bit 1
9007816 STRAIGHT-GRIP AIR SCREWDRIVER V1.0
www.princessauto.com / 1-800-665-8685 Page 14
This page is intentionally left blank.
This page is intentionally left blank.
V1,0 9007816
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.
Conservez ce manuel afin de pouvoir le consulter plus tard.
Cette page a été laissée blanche intentionnellement.
SPÉCIFICATIONS
Entrée d’air 1/4 po
Type de letage NPTF
Plage de pression 0 à 90 lb/po carré
Débit moyen à un temps de fonctionnement de 15 secondes 4,5 pi cubes/min
Débit à pleine charge 4,5 pi cubes/min
Vitesse nominale 9 000 tr / min
Plage de couple 0 à 480 po-lb
Diamètre min. de tuyau 3/8 po
Longueur hors tout 7 po
Type de manche Droit
Matériau de manche Aluminium
INTRODUCTION
Le tournevis à air comprimé est idéal pour serrer et desserrer rapidement les
xations lors de projets d’envergure. Il se caractérise par un commutateur de
marche avant/arrière et un régulateur pneumatique pour contrôler la vitesse du
mandrin.
SÉCURITÉ
AVERTISSEMENT! Veuillez lire et comprendre toutes les instructions
avant d’utiliser cet outil. L’opérateur doit respecter les précautions
élémentaires pour réduire le risque de blessure corporelle ou de
dommage à l’équipement.
DÉFINITIONS DE DANGER
Veuillez vous familiariser avec les avis de danger qui sont présentés dans ce
manuel. Un avis est une alerte indiquant qu’il existe un risque de dommage
matériel, de blessure ou de mort si on ne respecte pas certaines instructions.
DANGER! Cet avis indique un risque immédiat et particulier qui entraînera des
blessures corporelles graves ou même la mort si on omet de prendre les
précautions nécessaires.
AVERTISSEMENT! Cet avis indique un risque particulier ou une pratique non sécuritaire qui
pourrait entraîner des blessures graves si on omet de prendre les
précautions nécessaires.
V1.0 TOURNEVIS À AIR COMPRIMÉ À PRISE DROITE 9007816
Page 3 www.princessauto.com / 1-800-665-8685
ATTENTION! Cet avis indique une situation possiblement dangereuse qui peut
entraîner des blessures mineures ou modérées si on ne procède pas de la
façon recommandée.
AVIS! Cet avis indique un risque particulier ou une pratique non sécuritaire qui
entraînera des dommages au niveau de l’équipement ou des biens, mais
non des blessures corporelles.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez votre aire
de travail propre, bien éclairée et exempte de toute distraction. Placez les
lampes de façon à ne pas travailler dans l’ombre.
2. Assurez-vous que les personnes qui ne portent pas l’équipement de
sécurité approprié ne se trouvent pas à proximité de l’aire de travail.
3. Rangez les outils inutilisés correctement dans un lieu sécurisé et sec pour
empêcher la rouille, les dommages ou un mauvais usage.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT! Portez de l’équipement de protection individuelle
homologué par l’Association canadienne de normalisation (CSA) ou
l’American National Standards Institute (ANSI).
ÉQUIPEMENT DE PROTECTION INDIVIDUELLE
AVERTISSEMENT! Portez de l’équipement de protection individuelle homologué
par l’Association canadienne de normalisation (CSA) ou l’American National
Standards Institute (ANSI).
1. Portez toujours des lunettes antiprojections qui orent une protection
frontale et latérale pour les yeux. L’équipement de protection des yeux
devrait être conforme à la norme CSA Z94.3-07 ou ANSI Z87.1 en fonction
du type de travail eectué.
2. L’outil peut être à haute pression. Portez des lunettes de sécurité et des
gants pour vous protéger au cours de l'opération. Gardez les mains à
l'écart des parties de caoutchouc exposées du tuyau.
3. Portez un écran facial panoramique de type approprié avec les lunettes de
sécurité puisque cette tâche peut créer des copeaux, des matières
abrasives ou des particules.
4. Portez des vêtements de protection conçus pour l'environnement de
travail et pour l'outil.
5. La source d’air utilisée avec cet outil peut causer des dommages auditifs.
Portez une protection d’oreille an d’éliminer ou de réduire le bruit.
9007816 TOURNEVIS À AIR COMPRIMÉ À PRISE DROITE V1.0
www.princessauto.com / 1-800-665-8685 Page 4
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Power Fist 9007816 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Power Fist 9007816 Owner's manual