PROPOINT 9082710 Le manuel du propriétaire
- Catégorie
- Outils électroportatifs
- Taper
- Le manuel du propriétaire
V1.0 9082710
Please read and understand all instructions before use. Retain this manual for future reference.
AIR IMPACT WRENCH
SUPER STUBBY
This page is intentionally left blank.
SPECIFICATIONS
Air Inlet 1/4 in.
Drive Size 1/2 and 3/8 in.
Max. Pressure Rating 90 PSI
Average CFM @ 15 Second Run Time 4 CFM
CFM @ Full Load 4 CFM
Hammer Mechanism Jumbo
Max. Bolt Capacity 5/8 in.
Torque Range 400 ft-lb
Max. Torque 600 ft-lb
Speed Rating 9,000 RPM
Min. Hose Size 3/8 in.
Air Exhaust Handle/bottom
Overall Length 3-3/8 in.
Weight 3 lb
Material Metal/aluminum alloy
INTRODUCTION
The impact wrench is ideal for tightening or loosening heavy duty nuts,
bolts and screws.
SAFETY
WARNING! Read and understand all instructions before
using this tool. The operator must follow basic precautions
to reduce the risk of personal injury and/or damage to the
equipment.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual.
A notice is an alert that there is a possibility of property damage, injury
or death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that will
result in severe personal injury or death if the proper precautions
are not taken.
V1.0 SUPER STUBBY AIR IMPACT WRENCH 9082710
Page 3 Assistance available at www.princessauto.com or 1-800-665-8685
WARNING! This notice indicates a specific hazard or unsafe practice that could
result in a serious injury if the proper precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that may
result in minor or moderate injury if proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will
result in equipment or property damage, but not personal injury.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean,
well-lit and free of distractions. Place lights so you are not working
in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away
from the work area.
3. Store unused tools properly in a dry, safe and secure location to
prevent rust, damage or misuse.
4. Do not install or use in the presence of flammable gases, dust or
liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved
by the Canadian Standards Association (CSA) or American
National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side
protection for the eyes. Eye protection equipment should comply
with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of
work performed.
2. Wear protective clothing and gloves designed for the work
environment, materials and tools.
a. Do not wear gloves when operating a tool that can snag the
material and pull the hand into the tool.
3. The tool may contain high pressure. Use safety glasses and gloves
for protection during operation. Keep hands clear of the exposed
rubber portions of the hose.
4. This tool can cause hearing damage. Wear ear protection gear to
eliminate or reduce the noise. If possible add a muffling device to
the air tool’s exhaust.
9082710 SUPER STUBBY AIR IMPACT WRENCH V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 4
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with
the moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and
balance enables better control in unexpected situations.
4. Securely hold this tool using both hands. Using a tool with only one
hand can result in loss of control.
5. Never point the air stream or tool at any point of your body, other
people or animals. Debris and dust ejected at high speed can
cause an injury.
6. Serious injury or death may occur from inhaling compressed air.
The air stream may contain carbon monoxide, toxic vapors or solid
particles. Never inhale compressed air directly from the pump or
air tool.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence to the
tool safety rules. If you use this tool unsafely or incorrectly,
you can suffer serious personal injury.
WARNING! Only use impact sockets with the impact wrench.
Impact sockets have thicker walls and are made of ductile
material to handle vibration. Regular drive sockets may
rupture or explode under stress, injuring you or a bystander.
WARNING! Immediately release the trigger if the tool's bit
becomes stuck or jammed. The tool’s torque can twist your
arm and cause an injury. The tool may twist out of your grip
and cause an injury to yourself or a bystander.
1. Use the correct tool for the job. This tool was designed for a
specific function. Do not modify or alter this tool or use it for an
unintended purpose.
V1.0 SUPER STUBBY AIR IMPACT WRENCH 9082710
Page 5 Assistance available at www.princessauto.com or 1-800-665-8685
2. Always disconnect the impact wrench from the power supply
before opening the belt guard cover. Make sure the belt guard
cover is closed before reconnecting the tool to the power supply.
3. A loose or mismatched bit may be ejected by the tool, causing an
injury to the user or a bystander.
4. Always hold the tool firmly in your hands before switching the tool
ON. The reaction to the motor’s torque may cause the tool to twist,
as it accelerates to full speed.
5. Never attempt to change the impact socket's direction of rotation
while it is active. This can damage the interlock feature built into
the switch. Be sure the impact socket has completely stopped and
engage any safety features before changing the rotation direction.
Turn the power off as an added precaution.
6. Clean the impact wrench's air vents often. The motor’s fan
will draw dust and other particulates into the tool. Excessive
accumulation of wood, plastic or metal particulates can create a
fire or electrical hazard.
7. Inspect the tool components periodically. Repair or replace
damaged or worn components. Only use identical replacement
parts when servicing.
POWER TOOL PRECAUTIONS
1. Do not use any power tool with a malfunctioning power switch
or control. A power tool that fails to respond to the controls is
dangerous and can cause an injury. A qualified technician must
repair and verify the power tool is operating correctly, before it can
be used.
2. Shut the power off and disconnect the impact wrench from
the power supply (if possible) before making any adjustments,
changing accessories, cleaning, servicing or when storing. Such
preventive safety measures reduce the risk of starting the tool
accidentally.
3. Check if the impact wrench's moving parts are misaligned or
binding before each use. Correct the issue before using the impact
wrench to avoid an injury or damage to the tool.
9082710 SUPER STUBBY AIR IMPACT WRENCH V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 6
4. Always be aware of the position of your hands relative to the
impact wrench. Avoid awkward hand positions where a sudden slip
could cause a hand to move into the impact socket. Never reach
behind or beneath the impact wrench.
5. Only use accessories that are specifically designed for use with
the impact wrench. Ensure the impact socket is tightly installed.
6. Only use an impact socket that exceeds the Speed rating and
impact rating (see Specifications).
7. Before using the impact wrench on a workpiece, test the impact
wrench by running it at the highest speed rating for at least
30 seconds in a safe position. Stop immediately if there is any
abnormal vibration or wobbling. Check the tool to determine the
cause.
8. Never touch the impact socket or workpiece during or immediately
after use. They may be hot and could inflict a burn injury.
9. Never use a tool with an impact socket that is cracked or worn.
Change the impact socket before using it.
10. Do not place the impact wrench down until the impact socket has
stopped moving. The impact wrench may catch the surface of work
material and wrench itself free, causing injury to the user or others
in the work area.
11. Avoid unintentional starts. Be sure that the regulator/throttle switch
is in the neutral or OFF position when not in use and before
connecting it to any air source.
12. Never point the impact wrench towards yourself. It could inflict an
injury.
AIR TOOL PRECAUTIONS
1. Use only clean and dry compressed air as a power source.
Contaminated or moist air will gradually damage the tool.
2. Install an in-line shutoff valve or regulator to allow immediate
control over the air supply in an emergency, even if a hose is
ruptured.
3. Discontinue tool use if it does not work properly or air is leaking.
Tag or mark the tool as ‘defective’ or ‘out of service’ until repaired.
V1.0 SUPER STUBBY AIR IMPACT WRENCH 9082710
Page 7 Assistance available at www.princessauto.com or 1-800-665-8685
4. Check the manufacturer’s maximum pressure rating for air tools
and accessories. Compressor outlet pressure must be regulated
to never exceed the maximum pressure rating of the tool (see
Specifications). Exceeding the maximum PSI rating can create a
bursting hazard, causing injury and property damage.
a. The tool does not regulate the pressure level. The power
output is in direct proportion to the air pressure available. An
external air pressure regulator is required to safely use this
tool.
5. Never use oxygen, combustible gas or any other bottled gas as
a power source. Any power source other than an air compressor
could cause an explosion and serious personal injury.
6. Turn OFF the valve and discharge any remaining air pressure after
each use or before adjusting the tool.
7. Do not leave the air tool unattended with its compressed air supply
on. Turn off the compressed air supply and bleed the air tool of any
remaining compressed air before leaving the air tool unattended.
8. Serious injury may occur from loose debris being propelled at
high speeds from the compressed air stream. Always wear OSHA
approved safety glasses to protect the eyes during operation of the
air compressor.
9. Always turn off the air compressor and drain tank pressure
completely before attempting maintenance or attaching air tools.
Release pressure slowly from the system.
10. Do not cover the air vents.
AIR HOSE PRECAUTIONS
1. Inspect the tool's air hose for cracks, fraying or other faults before
each use. Discontinue use if the air hose is damaged or hissing
is heard from the air hose or couplers. Replace the defective air
hose.
2. Do not allow people, mobile equipment or vehicles to pass over the
unprotected air hose. Position the air hose away from high traffic
areas, in a reinforced conduit or place planks on both sides of the
air hose to create a protective trench.
9082710 SUPER STUBBY AIR IMPACT WRENCH V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 8
3. Prevent damage to the air hose by observing the following:
a. Never carry the tool by the air hose.
b. Keep the air hose behind the tool and out of the tool's work
path.
c. Keep the air hose away from heat, oil, sharp edges or moving
parts.
d. Do not wrap the air hose around the tool as sharp edges may
pierce or crack the air hose. Gently coil the hose and either
hang on a hook or fasten with a device to keep hose together
when storing.
4. A damaged or disconnected air hose under pressure may whip
around and inflict personal injury or damage the work area. Secure
the compressor's air hose to a fixed or permanent structure with
clamps or cable ties.
KICKBACK PRECAUTIONS
Kickback is a sudden reaction when an impact socket snags or is
caught on the material. If kickback occurs:
• The impact socket may contact a body part, causing a serious
injury
•The tool may strike bystanders.
•Kickback can also damage the tool or workpiece.
Kickback can be avoided by taking proper precautions:
1. Maintain a firm grip on the tool and position your body and arms to
allow you to resist a kickback. Kickback will propel the tool in the
direction opposite the impact socket's direction of rotation. The tool
may pull out of your grasp.
a. Use clamps or a vice to hold down smaller workpieces.
2. Only use an impact socket designed for the tool.
3. Maintain control of a long workpiece or large panel by placing
supports under the material on either side of the impact wrench.
V1.0 SUPER STUBBY AIR IMPACT WRENCH 9082710
Page 9 Assistance available at www.princessauto.com or 1-800-665-8685
VIBRATION PRECAUTIONS
1. This tool vibrates during use. Repeated or long-term exposure to
vibration may cause temporary or permanent physical injury. Take
frequent breaks when using the tool.
2. If you feel any medical symptoms related to vibrations (such
as tingling, numbness, and white or blue fingers), seek medical
attention as soon as possible.
3. Wear suitable gloves to reduce the effects of vibration.
4. DO NOT use this tool before consulting a physician if one of the
following applies:
a. Pregnant
b. Impaired blood circulation to
the hands
c. Past hand injuries
d. Nervous system disorders
e. Diabetes
f. Raynaud's Disease
UNPACKING
WARNING! Do not operate the tool if any part is missing.
Replace the missing part before operating. Failure to do so
could result in a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for
damage.
Contents:
• the impact wrench's
• (4) Impact socket: 13, 17, 19
and 21 mm
• 14 mm Impact Extension Bar
• (2) 3/8 and 1/2 in. Drive Anvil
Adaptors
• (2) 8 and 10 mm Bit Holders
• (2) 14 mm Hex and Star T60
Bits
• Pin
• Molded Carrying Case
9082710 SUPER STUBBY AIR IMPACT WRENCH V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 10
OPERATION
INSTALLING THE DRIVE ACCESSORIES
The impact wrench has a number of accessories that are designed
to withstand the the impact wrench's power and torque. Only use
accessories designed for an impact wrench.
1. Disconnect the power source
before installing or servicing the
tool.
2. Insert the pin into the drive collar's
hole and push. This will push
anvil's pin inward.
3. Pull the anvil from the drive collar. Pull straight, as the fit is tight.
4. All accessories are inserted into the drive collar by the hexagonal
end and pushed in until seated. Align the accessory's pin with
the drive collar's hole. This will prevent the accessory from being
thrown from the tool.
5. The other anvil, hex drive bit and star drive bit are ready for use
once seated.
6. The extension bar increases the tool's reach for recessed screws,
nuts or bolts. Once the extension bar is seated, insert a drive bit,
socket or the bit holder into the other end.
7. The bit holder allows you to use smaller bits with the impact
wrench. The bit holder is magnetic to prevent the bit from falling
out.
SOCKET INSTALLATION
CAUTION! Make sure that the nut or bolt you are using
the tool to tighten can withstand the rated torque and
RPM (see Specifications). Consult the recommended torque
specifications for the nut or bolt.
1. Select the appropriately sized drive impact socket for the job. Only
use impact sockets which are specifically designed for use with an
impact wrench. Do not use worn or damaged sockets.
2. Push and snap the socket onto the anvil.
Figure 1.
V1.0 SUPER STUBBY AIR IMPACT WRENCH 9082710
Page 11 Assistance available at www.princessauto.com or 1-800-665-8685
THE IMPACT WRENCH'S CONTROLS
The impact wrench has a forward/reverse switch to change direction
and a control dial to adjust the airflow.
1. Rotate the dial behind the trigger to set the airflow. The amount of
air increases as higher numbers are selected.
2. Push the forward/reverse switch down for reverse. The anvil will
rotate counterclockwise.
3. Push the forward/reverse switch up for forward. The anvil will
rotate clockwise.
OPERATING THE IMPACT WRENCH
1. Tighten the fastener as far as you can by hand before using the
impact wrench.
2. Place the socket over the anvil or insert the bit and grip the impact
wrench firmly with both hands.
3. Apply power in short bursts to avoid stripping the nut or bolt.
• Release the trigger if the tool stalls. The torque may inflict an
injury by twisting your arm. Use other methods and tools to
tighten or loosen the fastener.
4. Maintain a firm grip, but allow the tool to guide your hands up or
down when a fastener moves vertically.
5. Release the trigger to stop the tool.
6. Use a torque wrench to check the fastener's torque.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient,
easier to control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace
damaged or worn components. Only use identical replacement
parts when servicing.
3. Only use accessories intended for use with this tool. Follow
instructions for changing accessories.
4. Keep the tool handles or gripping surfaces clean and dry.
9082710 SUPER STUBBY AIR IMPACT WRENCH V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 12
5. Maintain the tool’s labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd.
for replacements.
6. Clear the vents of any dirt, dust and debris on a regular basis to
prevent the tool from overheating.
WARNING! Only qualified service personnel should repair
the tool. An improperly repaired tool may present a hazard
to the user and/or others.
CLEANING
1. Remove dust and debris from the motor's vents with a cloth, brush
or vacuum. Do not use compressed air, as it may blow dust into
the motor.
2. Only clean with a damp cloth. Avoid using solvents when cleaning
plastic parts.
AIR TOOL LUBRICATION
NOTICE! Only use air tool oil to lubricate the tool. Other
lubricants are not suitable and will damage the tool or cause
a malfunction during use.
NOTICE! Never use a penetrating oil to lubricate an air tool.
Penetrating oil acts as a solvent that will dissolve the tool’s
grease packing and may damage the o-rings, causing the
tool to seize or malfunction.
1. All air tools have an internal coating of grease to prevent corrosion
during shipping and storage. Remove this grease by adding a
generous amount of air tool oil in the air inlet and then run the tool
under no load until the exhaust is clear.
2. Manually add a drop or two of air tool oil into the tool’s coupler
plug before each use and after every hour of continuous use. The
tool will not work properly without lubrication and parts will wear
prematurely.
3. Avoid adding too much air tool oil as this can cause premature
power loss and eventual tool failure. A qualified technician will
need to take the tool apart and clean out the excess oil.
4. Apply a generous amount of air tool oil to the tool before storing
it for an extended period of time (overnight, weekend, etc.). Run
V1.0 SUPER STUBBY AIR IMPACT WRENCH 9082710
Page 13 Assistance available at www.princessauto.com or 1-800-665-8685
the tool for approximately 30 seconds to ensure the oil is evenly
distributed throughout the tool. Store it in a clean and dry location.
STORAGE
When not in use for an extended period, apply a thin coat of lubricant to
the steel parts to avoid rust. Remove the lubricant before using the tool
again.
1. Components should be kept dry, with machined surfaces lightly
oiled.
2. Always remove the impact socket and store in a safe place.
3. Never store equipment in a wet/damp environment.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws
for electronic devices, batteries, oil or other toxic liquids.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not
function properly or parts are missing. If unable to do so, have a
qualified technician service the tool.
THE IMPACT WRENCH'S
Problem(s) Possible Cause(s) Suggested Solution(s)
The impact
wrench will not
start.
1. Supplied power is
interrupted.
2. Motor components are
defective.
1. Check that power supply is
still available.
2. Have a qualified technician
service the tool.
9082710 SUPER STUBBY AIR IMPACT WRENCH V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 14
Problem(s) Possible Cause(s) Suggested Solution(s)
Motor starts
slow and
doesn't reach
operation
speed.
1. Air flow or air pressure is
too low.
2. Motor is damaged.
1. Adjust air flow or
air pressure to match
tool requirements (see
Specifications).
2. Have a qualified technician
service the tool.
Tool is making
unusual
sounds.
1. The impact wrench's parts
may be rubbing or binding.
2. Worn tool components
1. Check for obstructions
or misaligned tool
components. Lubricate,
repair or replace the
components based on the
particular problem.
2. Check and replace worn
parts.
Overheating 1. Forcing machine to work
too fast.
2. Blocked motor housing
vents.
1. Allow machine to work at its
own rate.
2. Blow dust out of motor
using compressed air.
AIR TOOL
Problem(s) Possible Cause(s) Suggested Solution(s)
Tool runs at
normal speed,
but loses power
under load.
1. Motor parts worn. 1. Have a qualified technician
service the tool.
2. Replace tool or parts.
V1.0 SUPER STUBBY AIR IMPACT WRENCH 9082710
Page 15 Assistance available at www.princessauto.com or 1-800-665-8685
Problem(s) Possible Cause(s) Suggested Solution(s)
Tool runs slowly.
Air flows slightly
from exhaust.
And/Or
Air flows slightly
from nozzle.
1. Motor parts jammed
with dirt particles.
OR
Airflow blocked by
dirt.
2. Air regulator in
closed position.
3. Air flow or air
pressure is too low.
4. Damage or
excessive wearing of
internal parts.
1. Check air inlet filter for
blockage.
a. Pour air tool lubricating
oil into air inlet as per
lubrication instructions for
clearing shipping grease.
b. Operate tool in short bursts
to clear debris.
c. If tool still jammed, clean
tool and lubricate per
lubrication instructions.
2. Open the air regulator to
desired airflow.
3. Adjust air flow or air pressure
to match tool requirements (see
Specifications).
4. Have a qualified technician
service the tool.
a. Replace tool or parts.
Tools will not run.
Air flows freely
from exhaust.
1. Damage or
excessive wearing of
internal parts.
2. Insufficient internal
lubrication.
1. Have a qualified technician
service the tool.
2. Replace tool or parts.
3. Lubricate tool per air tool
lubrication instructions.
Tool will not shut
off.
1. Throttle valve o-ring
dislodged from inlet
valve seat.
2. Trigger mechanism
jammed or dirty.
1. Replace throttle valve o-rings.
2. Clean trigger mechanism and
lubricate.
Loss of power or
erratic
performance.
1. Excessive drain
on the air hose.
Incorrect size or
type of hose
connectors.
2. Moisture or
restriction in the air
hose/tank
3. Air compressor has
insufficient flow.
1. Check the air hose and confirm
the hose fitting is correct for the
inlet bushing.
2. Depressurize system and drain
tank and air hose of water.
3. Ensure tool is connected to a
compressor with a rate flow that
matches the tool.
9082710 SUPER STUBBY AIR IMPACT WRENCH V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 16
V1,0 9082710
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce
manuel afin de pouvoir le consulter plus tard.
CLÉ À CHOCS PNEUMATIQUE
SUPER TRONQUÉE
Cette page a été laissée blanche intentionnellement.
SPÉCIFICATIONS
Entrée d’air 1/4 po
Taille de prise 1/2 et 3/8 po
Pression nominale max. 90 lb/po carré
Débit moyen à un temps de fonctionnement de 15
secondes 4 pi cubes/min
Débit à pleine charge 4 pi cubes/min
Mécanisme de frappe Jumbo
Capacité max. de boulon 5/8 po
Plage de couple 400 pi-lb
Couple max. 600 pi-lb
Vitesse nominale 9 000 tr / min
Diamètre min. de tuyau 3/8 po
Échappement d’air Poignée/dessous
Longueur hors tout 3 3/8 po
Poids 3 lb
Matériau Alliage d’aluminium/métal
INTRODUCTION
Le tournevis à percussion est idéal pour serrer ou desserrer les écrous,
boulons et vis robustes.
SÉCURITÉ
AVERTISSEMENT! Veuillez lire et comprendre toutes
les instructions avant d’utiliser cet outil. L’opérateur
doit respecter les précautions élémentaires pour réduire
le risque de blessure corporelle ou de dommage à
l’équipement.
DÉFINITIONS DE DANGER
Veuillez vous familiariser avec les avis de danger qui sont présentés
dans ce manuel. Un avis est une alerte indiquant qu’il existe un risque
de dommage matériel, de blessure ou de mort si on ne respecte pas
certaines instructions.
V1.0 CLÉ À CHOCS PNEUMATIQUE SUPER TRONQUÉE 9082710
Page 3 Assistance available at www.princessauto.com or 1-800-665-8685
DANGER! Cet avis indique un risque immédiat et particulier qui
entraînera des blessures corporelles graves ou la mort si
on omet de prendre les précautions nécessaires.
AVERTISSEMENT! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui pourrait entraîner des blessures graves si on
omet de prendre les précautions nécessaires.
ATTENTION! Cet avis indique une situation possiblement dangereuse qui
peut entraîner des blessures mineures ou modérées si on
omet de prendre les précautions nécessaires.
AVIS! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui entraînera des dommages à l’équipement
ou des dommages matériels, mais non des blessures
corporelles.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez
votre aire de travail propre, bien éclairée et exempte de toute
distraction. Placez les lampes de façon à ne pas travailler dans
l’ombre.
2. Assurez-vous que les personnes qui ne portent pas l’équipement
de sécurité approprié ne se trouvent pas à proximité de l’aire de
travail.
3. Rangez les outils inutilisés correctement dans un lieu sécurisé
et sec pour empêcher la rouille, les dommages ou un mauvais
usage.
4. Évitez d’installer ou d’utiliser des outils électriques en présence de
gaz, de poussière ou de liquides inflammables.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT! Portez de l’équipement de protection
individuelle homologué par l’Association canadienne de
normalisation (CSA) ou l’American National Standards
Institute (ANSI).
ÉQUIPEMENT DE PROTECTION INDIVIDUELLE
1. Portez toujours des lunettes antiprojections qui offrent une
protection frontale et latérale pour les yeux. L’équipement de
protection des yeux devrait être conforme à la norme CSA
Z94.3-07 ou ANSI Z87.1 en fonction du type de travail effectué.
9082710 CLÉ À CHOCS PNEUMATIQUE SUPER TRONQUÉE V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 4
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
PROPOINT 9082710 Le manuel du propriétaire
- Catégorie
- Outils électroportatifs
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: PROPOINT 9082710 Owner's manual
Documents connexes
Autres documents
-
Power Fist 8844060 Le manuel du propriétaire
-
-
-
Powerfist 9103268 Le manuel du propriétaire
-
-
-
-
-
-