Power Fist 8843575 Le manuel du propriétaire

Marque: Power Fist

Modèle: 8843575

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

V1.0 8843575

Please read and understand all instructions before use. Retain this manual for future

reference.

AIR HAMMER

SHORT BARREL

8843575 Short Barrel Air Hammer V1.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Air Inlet 1/4 in.

Working Pressure 90 PSI

Air Consumption @ 90 PSI 5.25 CFM

Blows per Minute 4,500 BPM

Stroke Length 1-5/8 in.

Min. Hose Size 3/8 in.

Material Die-cast Aluminum Housing

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or

death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may

result in minor or moderate injury if proper practices are not

taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice

will result in equipment or property damage, but not personal

injury.

V1.0 Short Barrel Air Hammer 8843575

Visit www.princessauto.com for more information 3

INTRODUCTION

The Short Barrel Air Hammer is good for cutting metals, chipping and

scraping surfaces for autobody work and home renovation.

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection

and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit

and free of distractions. Place lights so you are not working in a shadow.

2. Keep anyone not wearing the appropriate safety equipment away from

the work area.

3. Store unused tools properly in a safe and dry location to prevent rust

or damage. Lock tools away and keep out of the reach of children.

4. Do not install or use in the presence of flammable gases, dust or

liquids.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side protection

for the eyes. Eye protection equipment should comply with CSA Z94.3-07

or ANSI Z87.1 standards based on the type of work performed.

2. The tool may contain high pressure. Use safety glasses and gloves for

protection during operation. Keep hands clear of the exposed rubber

portions of the hose.

3. Wear the appropriate type of full-face shield in addition to safety googles,

as the work can create chips, abrasive or particulate matter.

4. Wear gloves that provide protection based on the work materials or to

reduce the effects of tool vibration.

5. Wear protective clothing designed for the work environment and tool.

8843575 Short Barrel Air Hammer V1.0

4 For technical questions call 1-800-665-8685

6. Non-skid footwear is recommended to maintain footing and balance in

the work environment.

7. Wear steel toe footwear or steel toe caps to prevent a foot injury from

falling objects.

8. Wear a NIOSH approved respirator when working on materials that

produce hazardous fumes, dust or particulate matter.

9. This tool can cause hearing damage. Wear hearing protection gear with an

appropriate Noise Reduction Rating to withstand the decibel levels.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to the tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating the tool. Proper footing and balance

enables better control in unexpected situations.

4. Securely hold this tool using both hands. Using a tool with only one

hand can result in loss of control.

5. Keep your fingers away from the trigger/switch while carrying the tool,

attaching an air hose or an accessory. Lock the trigger/switch safety if

available.

6. Avoid unintentional starts. Be sure that the regulator/throttle switch is

in the neutral or OFF position when not in use and before connecting it

to any air source.

7. Never point the air stream or tool at any point of your body, other people

or animals. Debris and dust ejected at high speed can cause an injury.

8. Serious injury or death may occur from inhaling compressed air. The air

stream may contain carbon monoxide, toxic vapors or solid particles.

Never inhale compressed air directly from the pump or air tool.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use this

tool unsafely or incorrectly, you can suffer serious personal injury.

V1.0 Short Barrel Air Hammer 8843575

Visit www.princessauto.com for more information 5

1. Use the correct tool for the job. This tool was designed for a specific

function. Do not modify or alter this tool or use it for an unintended

purpose.

2. Do not use the tool if any parts are damaged, broken or misplaced.

Repair or replace the parts.

3. Before using this tool, make sure you know the work area and material

you are working on. Make sure you do not accidentally puncture pipes,

pressurized containers or electrical cables.

4. Keep hands and other body parts away from the chisel to avoid injury.

5. Only use with accessories rated to handle the forces exerted by this

tool during operation. Accessories not designed for the forces

generated may break and forcefully launch pieces.

6. The chisels will become hot while chipping. Allow the chisels to

completely cool before touching.

7. When chipping in a potentially explosive environment, use a spark

resistant chisel (usually made of beryllium copper).

8. Replace chisels that are worn or blunt at the cutting edge or shank. A

damaged chisel may damage the air hammer, reduce efficiency and

increase vibration. A chisel that breaks during use can cause an injury.

9. Do not store chisels below 0°C (32°F). Freezing temperatures may cause

hardened steel to become brittle. A brittle chisel may shatter or break

and cause an injury.

10. Do not cover the air vents.

AIR TOOL PRECAUTIONS

1. Use only clean and dry compressed air as a power source.

Contaminated or moist air will gradually damage the tool.

2. Install an in-line shutoff valve or regulator to allow immediate control over

the air supply in an emergency, even if a hose is ruptured.

3. Discontinue tool use if it does not work properly or air is leaking. Tag

or mark the tool as ‘defective’ or ‘out of service’ until repaired.

4. Check the manufacturer’s maximum pressure rating for air tools and

accessories. Compressor outlet pressure must be regulated to never

exceed the maximum pressure rating of the tool (see Specifications).

Exceeding the maximum PSI rating can create a bursting hazard,

causing injury and property damage.

8843575 Short Barrel Air Hammer V1.0

6 For technical questions call 1-800-665-8685

5. Attach all accessories properly to the tool before connecting the air

supply. A loose accessory may detach or break during operation.

6. Never use oxygen, combustible gas or any other bottled gas as a

power source. Any power source other than an air compressor could

cause an explosion and serious personal injury.

7. Turn OFF the valve and discharge any remaining air pressure after each

use or before adjusting the tool.

8. Do not leave the air tool unattended with its compressed air supply on.

Turn off the compressed air supply and bleed the air tool of any

remaining compressed air before leaving the air tool unattended.

9. Serious injury may occur from loose debris being propelled at high speeds

from the compressed air stream. Always wear OSHA approved safety glasses

to protect the eyes during operation of the air compressor.

10. Always turn off the air compressor and drain tank pressure completely

before attempting maintenance or attaching air tools. Release pressure

slowly from the system.

11. Serious injury or death may occur from inhaling compressed air. The air

stream may contain carbon monoxide, toxic vapors or solid particles.

Never inhale compressed air directly from the pump or air tool.

POWER TOOL PRECAUTIONS

1. Do not use any power tool with a malfunctioning power switch or control.

A power tool that fails to respond to the controls is dangerous and can

cause an injury. A qualified technician must repair and verify the power

tool is operating correctly, before it can be used.

2. Avoid unintentional starts. Ensure the switch is off when connecting to

the power source.

3. Disconnect the power source before installing or servicing the tool.

4. Never force the tool. Excessive pressure could break the tool, resulting

in damage to your workpiece or serious personal injury. Excessive

pressure is the cause if your tool runs smoothly under no load, but

roughly under load.

5. Only use an accessory that exceeds the Beats Per Minute rating (see

Specifications). Ensure the accessory is tightly installed.

6. Before using the tool on a workpiece, test the tool by running it at the

highest no load speed for at least 30 seconds in a safe position. Stop

immediately if there is any abnormal vibration or wobbling. Check the

tool to determine the cause.

V1.0 Short Barrel Air Hammer 8843575

Visit www.princessauto.com for more information 7

7. Never touch the tool accessory or workpiece during or immediately

after use. They may be hot and could inflict a burn injury.

8. Never use a tool with a cracked or worn tool accessory. Change the

tool accessory before using it.

9. Do not place the tool down until the tool’s accessory has stopped moving.

The accessory may catch the surface of work material and wrench itself

free, causing injury to the user or others in the work area.

10. The tool is not insulated against contact with live electrical conduits or

sources. The tool’s exposed metal surfaces may convey a shock to the

operator from a ‘live’ wire.

11. Gum and wood pitch hardened on an accessory slows the tool and

increases the potential for kickback. Remove the accessory from the

tool, then clean it with gum and pitch remover, hot water or kerosene.

Never use gasoline. Allow to dry before use. Discard the accessory if

the gum or pitch cannot be removed.

AIR HOSE PRECAUTIONS

1. Inspect the tool's air hose for cracks, fraying or other faults before

each use. Discontinue use if the air hose is damaged or hissing is heard

from the air hose or couplers. Replace the defective air hose.

2. Do not allow people, mobile equipment or vehicles to pass over the

unprotected air hose. Position the air hose away from high traffic

areas, in a reinforced conduit or place planks on both sides of the air

hose to create a protective trench.

3. Prevent damage to the air hose by observing the following:

a. Never carry the tool by the air hose.

b. Keep the air hose behind the tool and out of the tool's work path.

c. Keep the air hose away from heat, oil, sharp edges or moving parts.

d. Do not wrap the air hose around the tool as sharp edges may

pierce or crack the air hose. Gently coil the hose and either hang

on a hook or fasten with a device to keep hose together when

storing.

4. A damaged or disconnected air hose under pressure may whip around

and inflict personal injury or damage the work area. Secure the

compressor's air hose to a fixed or permanent structure with clamps or

cable ties.

8843575 Short Barrel Air Hammer V1.0

8 For technical questions call 1-800-665-8685

COMPRESSOR/TANK PRECAUTIONS

DANGER! Do not use an air tank beyond its expiration date. A tank rupture

or explosion may kill or cause a serious injury to yourself or a bystander.

Disable and discard the air tank according to the your municipality by-laws.

1. Never drill into, weld, patch or modify the air tank. Immediately replace the

tank or compressor if an air leak develops. The leak may lead to a rupture.

2. Never make adjustments to the components that control tank pressure.

Serious injury or death may occur if modifications are made to the

pressure switch, safety relief valve or other components that control

the tank pressure.

3. Check operation of the pressure relief valve on a regular basis and

never operate without a factory approved pressure relief valve. Do not

make alterations to the factory operating pressure settings.

VIBRATION PRECAUTIONS

1. This tool vibrates during use. Repeated or long-term exposure to

vibration may cause temporary or permanent physical injury. Take

frequent breaks when using the tool.

2. If you feel any medical symptoms related to vibrations (such as

tingling, numbness, and white or blue fingers), seek medical attention

as soon as possible.

3. Wear suitable gloves to reduce the effects of vibration.

4. DO NOT use this tool before consulting a physician if one of the

following applies:

a. Pregnant

b. Impaired blood circulation

to the hands

c. Past hand injuries

d. Nervous system disorders

e. Diabetes

f. Raynaud's Disease

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the contents are included.

Contents: • Short Barrel Air Hammer • Chisels (4)

• Spring Retainer • Air Plug

V1.0 Short Barrel Air Hammer 8843575

Visit www.princessauto.com for more information 9

IDENTIFICATION KEY

A Retainer Spring

B Cylinder

C Trigger

D Air Inlet

E Air Regulator

F Chisel, Flat Punch

G Chisel, Ripper

H Chisel, Tapered Punch

I Chisel, Weld Buster/Bolt Cutter

ASSEMBLY & INSTALLATION

Letter references in parenthesis (A) refer to the included Identification Key.

INSTALL AIR PLUG

Prepare a standard 1/4 in. NPT male air plug (sold separately) for use with

your tool.

1. Wrap the external threads of the male plug with sealant tape.

a. Wrap tape in a clockwise direction so it will not unravel.

b. Do not tape all the threads. Leave several leading threads

unwrapped for easier alignment.

2. Screw the plug into the tool's air inlet (D) and tighten with a wrench

until snug.

3. Run the compressor at a low volume and check the connection for air

leaks. Do not use the tool until all air leaks are repaired or the faulty

component is replaced.

IMPORTANT! Vibration may cause failure if a quick coupler is connected directly

to the air tool. To overcome this, connect a leader hose to the tool. A quick

coupler may then be used to connect the leader hose to the air line hose.

INSTALL SPRING RETAINER AND CHISEL

1. Remove the internal packing grease from the tool before the first use.

See Air Tool Lubrication for instructions.

2. Disconnect the tool from its air source and discharge any residual air

before attaching or changing chisels or accessories.

Fig. 1

8843575 Short Barrel Air Hammer V1.0

10 For technical questions call 1-800-665-8685

3. Select your chisel (F to I). Make sure it is in good working condition and

will not shatter or break while in use.

4. Remove the spring retainer (A). Unscrew the coil by the rear loop. It

will spread the spring out slightly, making it easier to unthread.

5. Insert the chisel shank into the tool’s cylinder (B)

6. Slide the spring retainer over the chisel. Align the rear of the spring

retainer (A) with the threads on the cylinder.

7. Thread the coil onto the cylinder.

8. Pull on the chisel to confirm it is locked into place. You may need to

rotate the chisel shank a bit for it to lock.

9. Test the chisel placement by running the tool at no load for

approximately 30 seconds. Point the chisel in a safe direction in case it

is ejected from the air hammer.

OPERATION

PRESSURE DROP

Apply the air consumption and pressure rate numbers to the tool’s air inlet, not

the compressor’s outlet. Calculate the pressure drop for your air supply set-up

and increase the compressor outlet pressure to compensate. Make sure you do

not exceed the maximum pressure for any part of your air supply system.

Installing a pressure gauge at the tool inlet is the best way to measure the

air pressure and adjust the compressor’s output.

TOOL OPERATION

1. Ensure the regulator switch is in the neutral or OFF position.

2. Connect the tool to the air source.

3. Turn the compressor regulator to the desired air pressure (see

Specifications).

4. Power is increased or decreased by adjusting the airflow with the

regulator (E) at the handle’s base.

5. Firmly grip the air hammer with both hands and place the chisel

against the workpiece.

6. Squeeze the trigger (C) and slowly move along the workpiece. Do not

force the air hammer; let the tool do the work.

7. If the chisel is not performing well, turn off the tool and examine the

chisel to see if it is dull. Replace with a sharp chisel. Remember that

sharp tools are safer than ones that have become dull.

V1.0 Short Barrel Air Hammer 8843575

Visit www.princessauto.com for more information 11

8. Once finished, disconnect the tool from its air source and discharge

any residual air in the tool before storing it.

9. Remove the chisel and the spring retainer after each use. Clean the air

hammer, retainer and chisels to make sure there is no accumulated

dust or debris remaining on the tool. Reinstall the retainer back onto

the air hammer before storage.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier

to control and will have fewer problems.

2. Inspect the tool fittings, alignment, hoses and power supply cord

periodically. Have damaged or worn components repaired or replaced

by an authorized technician. Only use identical replacement parts

when servicing.

3. Follow instructions for lubricating and changing accessories.

4. Only use accessories intended for use with this tool.

5. Keep the tool handles clean, dry and free from oil/grease at all times.

6. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

AIR TOOL LUBRICATION

NOTICE! Only use air tool oil to lubricate the tool. Other lubricants are not

suitable and will damage the tool or cause a malfunction during use.

NOTICE! Never use a penetrating oil to lubricate an air tool. Penetrating oil

acts as a solvent that will dissolve the tool’s grease packing and may

damage the o-rings, causing the tool to seize or malfunction.

1. All air tools have an internal coating of grease to prevent corrosion

during shipping and storage. Remove this grease by adding a generous

amount of air tool oil in the air inlet and then run the tool under no

load until the exhaust is clear.

2. Manually add a drop or two of air tool oil into the tool’s male plug before

each use and after every hour of continuous use. The tool will not work

properly without lubrication and parts will wear prematurely.

8843575 Short Barrel Air Hammer V1.0

12 For technical questions call 1-800-665-8685

3. Avoid adding too much air tool oil as this can cause premature power

loss and eventual tool failure. A qualified technician will need to take

the tool apart and clean out the excess oil.

4. Apply a generous amount of air tool oil to the tool before storing it for

an extended period of time (overnight, weekend, etc.). Run the tool for

approximately 30 seconds to ensure the oil is evenly distributed

throughout the tool. Store it in a clean and dry location.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

Problem(s) Possible Cause(s) Suggested Solution(s)

Tool runs at

normal speed, but

loses power

under load.

Motor parts worn.

1. Have a qualified technician

service the tool.

2. Replace tool or parts.

Tool runs slowly.

Airflows slightly

from exhaust.

Motor parts jammed with

dirt particles.

Airflow blocked by dirt.

1. Check air inlet filter for

blockage.

2. Pour air tool lubricating oil

into air inlet as per

lubrication instructions for

clearing shipping grease.

3. Operate tool in short bursts

to clear debris.

4. If tool still jammed, clean

tool and lubricate per

lubrication instructions.

Tool runs slowly.

Airflows slightly

from exhaust.

1. Air regulator in closed

position.

2. Damage or excessive

wearing of internal parts.

1. Open the air regulator to

desired airflow.

2a. Have a qualified technician

service the tool.

2b. Replace tool or parts.

Tools will not run.

Airflows freely

from exhaust.

Damage or excessive

wearing of internal parts.

1. Have a qualified technician

service the tool.

2. Replace tool or parts.

V1.0 Short Barrel Air Hammer 8843575

Visit www.princessauto.com for more information 13

Problem(s) Possible Cause(s) Suggested Solution(s)

Impact tools will

not run. Airflows

freely from exhaust.

Piston is jammed

1. Remove chisel and spring

retainer.

2. Push punch through hole in

the cylinder until resting

against the piston.

3. Sharply strike punch with a

hammer to loosen piston.

4. If still jammed, disassemble

barrel from housing and use

punch to push piston through

the rear of barrel.

5. Clean the barrel and piston.

Remove any rust.

6. Reassemble.

Tool will not shut

off.

1. Throttle valve o-ring

dislodged from inlet

valve seat.

2. Trigger mechanism

jammed or dirty.

1. Replace throttle valve

o-rings.

2. Clean trigger mechanism and

lubricate.

Loss of power

or erratic

performance.

1. Excessive drain on

the air hose.

Incorrect size or type

of hose connectors.

2. Moisture or

restriction in the air

hose/tank

3. Air compressor has

insufficient flow.

1. Check the air hose and confirm

the hose fitting is correct for

the inlet bushing.

2. Depressurize system and drain

tank and air hose of water.

3. Ensure tool is connected to a

compressor with a rate flow

that matches the tool.

8843575 Short Barrel Air Hammer V1.0

14 For technical questions call 1-800-665-8685

PARTS BREAKDOWN

PARTS LIST

# DESCRIPTION QTY

Main housing 1

Valve seat 1

Valve plate 1

End cap 1

Piston 1

Cylinder 1

Spring retainer 1

Chisel 4

Valve stem 1

Valve 1

Valve spring 1

Air inlet 1

Bushing 1

O-ring 2

Air Regulator 1

Bolt 1

Trigger 1

Bolt 1

V1,0 8843575

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.

Conservez ce manuel afin de pouvoir le consulter plus tard.

MARTEAU

PNEUMATIQUE

À CYLINDRE COURT

8843575 Marteau pneumatique à cylindre court V1,0

2 En cas de questions techniques, appelez le 1-800-665-8685

SPÉCIFICATIONS

Entrée d’air 1/4 po

Pression de travail 90 lb/po carré

Consommation d’air à 90 lb/po carré 5.25 pi cubes/min

Coups par minute 4 500 coups/min

Longueur de course 1 5/8 po

Diamètre min. de tuyau 3/8 po

Matériau

Boîtier en aluminium coulé sous

pression

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce

manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage

à la propriété, de blessure ou de décès si on ne respecte pas certaines

instructions.

DANGER ! Cet avis indique un risque immédiat et particulier qui

entraînera des blessures corporelles graves ou même la

mort si on omet de prendre les précautions nécessaires.

AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique non

sécuritaire qui

pourrait entraîner des blessures

corporelles graves ou même la mort si on omet de

prendre les précautions nécessaires.

ATTENTION ! Cet avis indique une situation possiblement dangereuse qui

peut entraîner des blessures mineures ou modérées si on

ne procède pas de la façon recommandée.

AVIS ! Cet avis indique un risque particulier ou une pratique non

sécuritaire qui entraînera des dommages au niveau de

l'équipement ou des biens, mais non des blessures

corporelles.

V1,0 Marteau pneumatique à cylindre court 8843575

Visitez www.princessauto.com pour plus d'informations 3

INTRODUCTION

Le marteau pneumatique à cylindre court convient idéalement pour la coupe

de métaux, le piquage et le raclage de surfaces pour les travaux de

carrosserie d’automobile et pour les rénovations de maison.

SÉCURITÉ

AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant

d'utiliser cet outil. L'utilisateur doit respecter les précautions de base

lorsqu'il utilise cet outil afin de réduire le risque de blessure ou de

dommage à l'équipement.

Conservez ce manuel qui contient les avertissements de sécurité, les

précautions, les instructions de fonctionnement ou d'inspection et d'entretien.

AIRE DE TRAVAIL

1. Travaillez dans un environnement de travail sécuritaire. Gardez votre

aire de travail propre, bien éclairée et exempte de toute distraction.

Placez les lampes de façon à ne pas travailler dans l’ombre.

2. Assurez-vous que les personnes qui ne portent pas l'équipement de

sécurité approprié ne se trouvent pas à proximité de l'aire de travail.

3. Rangez les outils correctement dans un lieu sécurisé et sec. Gardez les

outils hors de la portée des enfants.

4. N'installez pas et n'utilisez pas d'outils électriques en présence de gaz,

de poussière ou de liquides inflammables.

SÉCURITÉ PERSONNELLE

AVERTISSEMENT ! Portez de l'équipement de protection personnelle

homologué par l'Association canadienne de normalisation (CSA) ou

l'American National Standards Institute (ANSI).

ÉQUIPEMENT DE PROTECTION PERSONNELLE

1. Portez toujours des lunettes antiprojections qui offrent une protection

frontale et latérale pour les yeux. L'équipement de protection des yeux

devrait être conforme à la norme CSA Z94.3-07 ou ANSI Z87.1 fonction

du type de travail effectué.

2. L’outil peut être à haute pression. Portez des lunettes de sécurité et des

gants pour vous protéger au cours de l'opération. Gardez les mains à

l'écart des parties de caoutchouc exposées du tuyau.

8843575 Marteau pneumatique à cylindre court V1,0

4 En cas de questions techniques, appelez le 1-800-665-8685

3. Portez un écran facial panoramique de type approprié avec les lunettes

de sécurité puisque cette tâche peut créer des copeaux, des matières

abrasives ou des particules.

4. Portez des gants qui protègent en fonction des matériaux de travail et

pour réduire les effets des vibrations de l'outil.

5. Portez des vêtements de protection conçus pour l'environnement de

travail et pour l'outil.

6. Les chaussures antidérapantes sont recommandées pour maintenir la

stabilité et l'équilibre au sein de l'environnement de travail.

7. Portez des chaussures à embout d'acier ou à coquilles d'acier pour éviter

les blessures aux pieds dues à la chute d'objets.

8. Portez un appareil respiratoire approuvé par la NIOSH pour travailler

sur des matériaux qui produisent des émanations dangereuses, de la

poussière ou des particules.

9. Cet outil peut causer des dommages à l'ouïe. Portez un dispositif de

protection anti-bruit présentant une cote de réduction du bruit

adéquate en fonction du niveau de décibels.

PRÉCAUTIONS PERSONNELLES

Gardez le contrôle de l'outil, de vos mouvements et de l'environnement de

travail pour éviter les blessures ou le bris de l'outil.

1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,

d'alcool ou de médicaments.

2. Évitez de porter des vêtements ou des bijoux pouvant se prendre dans

les pièces mobiles d'un outil. Gardez les cheveux longs recouverts ou

attachés.

3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en servir.

Une stabilité et un équilibre appropriés sont nécessaires afin d'avoir un

meilleur contrôle en cas de situations inattendues.

4. Tenez cet outil solidement à l’aide des deux mains. Un outil tenu d’une

seule main peut causer une perte de contrôle.

5. Gardez vos doigts à bonne distance de la gâchette/commutateur lors

du transport de l’outil ou du branchement d’un tuyau à air ou d’un

accessoire. Engagez le verrou de gâchette/interrupteur, le cas échéant.

6. Évitez les mises en marche involontaires. Assurez-vous que le

régulateur/commutateur est en position neutre ou OFF (arrêt) lorsque

l’outil n’est pas utilisé et avant de le brancher à une source d’air.

V1,0 Marteau pneumatique à cylindre court 8843575

Visitez www.princessauto.com pour plus d'informations 5

7. Ne dirigez jamais le jet d’air ou les outils vers votre corps, d’autres

individus ou des animaux. Les débris et la poussière projetés à grande

vitesse peuvent causer des blessures.

8. Des blessures graves ou même la mort peuvent survenir en cas

d’inhalation de l’air comprimé. Le jet d’air peut contenir du monoxyde

de carbone, des vapeurs toxiques ou des particules solides. N’inhalez

jamais l’air comprimé provenant directement de la pompe ou d’un outil

pneumatique.

CONSIGNES DE SÉCURITÉ SPÉCIFIQUES

AVERTISSEMENT ! Ne permettez PAS au confort ou à votre familiarisation

avec l'outil (obtenus après un emploi répété) de se substituer à une

adhésion stricte aux règles de sécurité de l'outil. Si vous utilisez cet outil de

façon dangereuse ou incorrecte, vous pouvez subir des blessures

corporelles graves.

1. Utilisez le bon outil pour la tâche à effectuer. Cet outil a été conçu pour

une utilisation spécifique. Évitez de modifier ou d'altérer cet outil ou de

l'utiliser à une fin autre que celle pour laquelle il a été conçu.

2. N’utilisez pas l’outil si des pièces présentent des dommages ou sont

déplacées. Réparez ou remplacez les pièces.

3. Avant d’utiliser cet outil, assurez-vous de bien connaître l’aire de travail et

le matériau sur lequel vous allez travailler. Veillez à ne pas percer par

mégarde des tuyaux, des récipients pressurisés ni des câbles électriques.

4. Gardez les mains et les autres parties du corps loin du ciseau afin de

prévenir les blessures.

5. N’utilisez que des accessoires certifiés pour supporter les forces

exercées par cet outil durant son fonctionnement. D’autres accessoires

non conçus pour résister aux forces produites risquent de se briser et

de voler en éclats avec force.

6. Pendant l’ébarbage, les ciseau deviennent chauds. Laissez refroidir

complètement les ciseau avant de les toucher.

7. Lors d’ébarbage dans un environnement à risque d’explosion, utilisez

un ciseau résistant aux étincelles (habituellement fabriqué en

cuprobéryllium).

8. Remplacez les ciseaux usés ou arrondis sur le tranchant ou la tige. Un

ciseau endommagé pourrait briser le marteau pneumatique, réduire

l’efficacité et augmenter les vibrations. Un ciseau qui se brise durant

l’utilisation peut causer une blessure.

8843575 Marteau pneumatique à cylindre court V1,0

6 En cas de questions techniques, appelez le 1-800-665-8685

9. N’entreposez pas les ciseaux à une température inférieure à 0 °C (32 °F).

Les températures de congélation peuvent faire en sorte que l’acier trempé

deviendra friable. Un ciseau friable peut se fracasser ou se briser,

entraînant ainsi des blessures.

10. Ne recouvrez pas les orifices d'aération.

PRÉCAUTIONS RELATIVES AUX OUTILS PNEUMATIQUES

1. Utilisez uniquement un air comprimé propre et sec comme source d’énergie.

L’air contaminé ou humide endommagera progressivement l’outil.

2. Installez une soupape d'arrêt ou un régulateur sur la conduite afin de

permettre une commande immédiate de l'alimentation en air, en cas

d'urgence, même si un tuyau se fend.

3. Arrêtez d’utiliser l’outil s’il ne fonctionne pas correctement ou s’il présente

des fuites d’air. Attachez une étiquette sur l’outil indiquant qu’il est «

défectueux » ou qu’il est « hors service », jusqu’à ce qu’il soit réparé.

4. Consultez la pression nominale maximale du fabricant en ce qui concerne

les outils pneumatiques et accessoires. La pression de sortie du

compresseur doit être réglée de façon à ne jamais dépasser la pression

nominale maximale de l'outil (consultez Spécifications). Si on dépasse la

pression nominale maximale, il pourrait en résulter un risque d’explosion

capable d’entraîner des blessures et des dommages aux biens.

5. Avant de relier l’alimentation en air, fixez correctement tous les

accessoires sur l’outil. Un accessoire mal attaché pourrait se détacher

et se briser durant l’utilisation.

6. N'utilisez jamais d'oxygène, de gaz combustible ou tout autre gaz

embouteillé en tant que source d'énergie. Une source d'énergie autre

qu'un compresseur d'air pourrait causer une explosion entraînant ainsi

des blessures corporelles graves.

7. Fermez la soupape et évacuez toute la pression d’air restante après

chaque utilisation ou avant d’ajuster l’outil.

8. Ne laissez pas l’outil d'air sans surveillance alors que la source d'air

comprimé est en fonction. Fermez la source d'air comprimé et purgez

l’outil d'air de tout air comprimé restant avant de laisser celui-ci sans

surveillance.

9. Des blessures graves peuvent se produire si des débris sont propulsés

à haute vitesse dans le jet d’air du compresseur. Portez toujours des

lunettes de sécurité approuvés OSHA afin de vous protéger les yeux

lorsque vous utilisez le compresseur d’air.

La page charge ...

Power Fist 8843575 Le manuel du propriétaire

Marque: Power Fist

Modèle: 8843575

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Power Fist 8843575 Owner's manual

Power Fist 8843575 Le manuel du propriétaire

Power Fist 8843575 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents