VTech VS122-16 DECT6.0 Cordless Phone Manuel utilisateur

Marque: VTech

Modèle: VS122-16 DECT6.0 Cordless Phone

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

VS122-16

VS122-16

Quick start guide

Scan the QR code for

support information

»Remplacement d’une batterie par un type incorrect pouvant supprimer une protection;

»mise au rebut d’une batterie dans un feu ou dans un four chaud, ou écrasement mécanique ou coupure d’une batterie, susceptible de provoquer

une explosion;

»maintien d’une batterie dans un environnement à très haute température pouvant provoquer une explosion ou la fuite de liquide ou de gaz

inﬂammables;

»batterie soumise à une pression de l’air extrêmement faible pouvant provoquer une explosion ou la fuite de liquide ou de gaz inﬂammables.

21. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la polarité ou la tension serait inadéquate risque d’endommager

sérieusement le produit et mettre votre sécurité en péril.

22. La plaque de noms appliquée se trouve au bas ou près du produit.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou l’équivalent. Pour commander une pile de recharge, visitez notre site Web au www.vtechphones.com ou composez

le 800-595-9511.

• Au Canada, visitez le phones. phones.vtechcanada.com ou composez le 800-267-7377.

• Ne jetez pas la pile au feu. Vériﬁez les instructions spéciﬁques de mise aux rebus auprès des autorités locales.

• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et pourrait causer des brûlures ou des blessures aux yeux ou à la

peau. L’électrolyte est toxique si avalé.

• Soyez prudents lorsque vous manipulez les piles aﬁn d’éviter les courts-circuits provoqués par des matériaux conducteurs.

• Rechargez la pile incluse avec cet appareil, selon les instructions et limites spéciﬁées dans ce guide d’utilisation.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans ﬁl):

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une ﬁrme de recherche indépendante, a mené une évaluation pluridisciplinaire des interférences

entre les téléphones sans ﬁl portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA)

des États-Unis, la ﬁrme WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Ils doivent tenir le téléphone sans ﬁl à une distance d’au moins six pouces du stimulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en

marche.

• Ils doivent utiliser le téléphone sans ﬁl en l’appuyant sur l’oreille qui se trouve dans la direction opposée au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de risque pour les détenteurs de simulateurs cardiaques causés par les gens qui utilisent un

téléphone sans ﬁl à proximité de ceux-ci.

À propos des téléphones sans ﬁl

• Alimentation électrique: Les mêmes caractéristiques qui constituent des avantages pour les téléphones sans ﬁl afﬁchent également des restrictions.

Les appels téléphoniques sont transmis entre le combiné sans ﬁl et le socle par le biais d’ondes radio ; il y a donc la possibilité que vos conversations

téléphoniques sans ﬁl soient interceptées par des équipements de réception radio se trouvant dans la portée du combiné sans ﬁl. Pour cette raison,

vous ne devez pas percevoir les communications téléphoniques sans ﬁl comme étant aussi conﬁdentielles.

• Alimentation électrique: Le socle de ce téléphone sans ﬁl doit être branché à une prise électrique fonctionnelle. La prise électrique ne doit pas être

contrôlée par un interrupteur mural. Les appels ne pourront pas être effectués du combiné sans ﬁl si le socle est débranché ou mis hors tension ou

si le courant est coupé.

• Possibilité d’interférences aux téléviseurs: Certains téléphones sans ﬁl fonctionnent sur des fréquences pouvant causer des interférences aux téléviseurs

et aux magnétoscopes. Pour réduire ou prévenir de telles interférences, ne placez pas le socle du téléphone sans ﬁl près ou sur un téléviseur ou

magnétoscope. S’il y a présence de parasites, il est conseillé d’éloigner le téléphone sans ﬁl du téléviseur ou du magnétoscope aﬁn de réduire

possiblement les interférences.

• Piles rechargeables: Manipulez les piles avec soin aﬁn de ne pas les court-circuiter avec des bagues, bracelets ou clés. Les piles ou le conducteur peut

surchauffer et causer des blessures. Respectez la polarité adéquate entre la pile et le chargeur.

• Les bloc-piles rechargeables à l’hydrure métallique de nickel: Jetez ces blocs-piles de manière écologique et sécuritaire. Ne les incinérez pas et ne les

percez pas. Tel que les autres piles de ce type, elles pourraient dégager une matière toxique qui peut causer des blessures corporelles si elles sont

brûlées ou percées.

The RBRC® seal

The RBRC® seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and

recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada.

The RBRC® program provides a convenient alternative to placing used nickel-metal hydride batteries into the trash or municipal waste, which may be

illegal in your area.

VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers participating in the RBRC® program or at

authorized

VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/restrictions in

your area.

VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.

RBRC® and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications

Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate

the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation. Privacy of communications may not be ensured when using this telephone.

To ensure safety of users, the FCC/ ISEDC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander

according to the intended usage of the product. This product has been tested and found to comply with the FCC/ ISEDC criteria. The handset may be safely

held against the ear of the user. The telephone base shall be installed and used such that parts of the user’s body other than the hands are maintained at a

distance of approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments

(ACTA). The label on the back or bottom of this equipment contains, among other things, a product identiﬁer in the format US:AAAEQ##TXXXX. This identiﬁer

must be provided to your telephone service provider upon request.

The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical

requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible

modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See the

installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are

called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identiﬁer (e.g., if ## is 03, the REN is 0.3). In most,

but not all areas, the sum of all RENs should be ﬁve (5.0) or less. For more information, please contact your telephone service provider.

This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the

connection of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your

telephone service provider or a qualiﬁed installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Replacement to this telephone

equipment can only be made by the manufacturer or its authorized agents. For replacement procedures, follow the instructions outlined under the “Limited

warranty”.

If this equipment is causing harm to the telephone network, the telephone service provider may temporarily discontinue your telephone service. The

telephone service provider is required to notify you before interrupting service. If advance notice is not practical, you will be notiﬁed as soon as possible.

You will be given the opportunity to correct the problem and the telephone service provider is required to inform you of your right to ﬁle a complaint with

the FCC. Your telephone service provider may make

changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The telephone service provider is

required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is hearing aid compatible. If this product has memory dialing locations, you may

choose to store emergency telephone numbers (e.g., police, ﬁre, medical) in these locations. If you do store or test emergency numbers, please:

Remain on the line and brieﬂy explain the reason for the call before hanging up.

Perform such activities in off-peak hours, such as early morning or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt

RSS(s).

Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation.

Privacy of communications may not be ensured when using this telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry Canada technical speciﬁcations were met.

The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN is an indication of the maximum number of devices allowed to be

connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum

of the RENs of all the devices does not exceed ﬁve.

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

California Energy Commission Battery charging testing instructions

This telephone is set up to comply with the energy-conserving standards right out of the box. These instructions are intended for California Energy

Commission (CEC) compliance testing only. When the CEC battery charging testing mode is activated, all telephone functions, except battery charging,

will be disabled.

To activate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet. Make sure all handsets are plugged with charged batteries before proceeding.

2. While you press and hold FIND HS, plug the telephone base power adapter back to the power outlet.

3. After about 20 seconds, when the HOME/FLASH light starts ﬂashing, release FIND HS and then press it again within two seconds. You hear

a conﬁrmation tone. The HOME/FLASH light turns on and all handsets display To register HS... see manual alternately. Allow up to one minute for

the process to complete.

If the phone fails to enter this mode, repeat all the steps mentioned above. The telephone base will be powered up as normal if you fail to press FIND

HS within two seconds in Step 3.

To deactivate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet, and then plug it back in. Then the telephone base is powered up as normal.

2. Put the handsets on the telephone base cradle to begin registration.

3. The handset shows Registering... If the registration is successful, the handset screen displays Registered and beeps. The handset is registered with

the telephone base.

Technical Speciﬁcations

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Handset: 1921.536-1928.448 MHz | Telephone base: 1921.536-1928.448 MHz

Channels DECT channel: 5

Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary

according to environmental conditions at the time of use.

Power requirement

Handset: 2.4 V DC, 400mAh, Ni-MH battery | Base: 6V DC @ 450mA

Power adapter: Output 6V DC @ 450mA (Base). Max. of PS1 or LPS. |

Output: 6V@400mA (Charger). Max. of PS1 or LPS.

Memory Phonebook: 1000 memory locations; up to 30 digits and 15 characters

Caller ID log: 50 memory locations; up to 24 digits and 15 characters

Call block: 1000 entries

The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by VTech Holdings Limited is under license.

VTech Holdings Limited is a member of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.

* Includes licenced Qaltel™ technology. Qaltel™ is a trademark of Truecall Group Limited.

The ENERGY STAR® program (www.energystar.gov) recognizes and encourages the use of products that save energy and help

protect our environment. We are proud to mark this product with the ENERGY STAR® label indicating it meets the latest energy

efﬁciency guidelines.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories

provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed

and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased

and used in the

United States of America and Canada.

What will VTech do if the Product is not free from defects in materials and workmanship

during the limited warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will replace at VTech’s option, without charge, a Materially Defective Product. If

we replace the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished

Product of the same or similar design. We will retain defective parts, modules, or equipment. Replacement of the Product, at VTech’s option, is your exclusive

remedy. VTech will return the replacement Products to you in working condition. You should expect the replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech replaces a Materially Defective Product under the

terms of this limited warranty, this limited warranty also applies to the replacement Product for a period of either (a) 90 days from the date the replacement

Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling,

neglect, inundation, ﬁre, water or other liquid intrusion.

2. Product that has been subjected to contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like; but then only to

the extent the damage was not caused by incorrectly securing the waterproof handset’s protective elements, for example, failing to properly close

a seal), or such protective elements are damaged or missing (e.g. a cracked battery door), or subjecting a Product to conditions beyond its stated

speciﬁcations or limits (e.g. 30 minutes in 1 meter of fresh water).

3. Product that has been damaged due to repair, alteration or modiﬁcation by anyone other than an authorized service representative of VTech;

4. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems;

5. Product to the extent that the problem is caused by use with non-VTech accessories;

6. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible;

7. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional

purposes (including but not limited to Products used for rental purposes);

8. Product returned without a valid proof of purchase (see item 2 below); or

9. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511.

To obtain warranty service in Canada, go to phones.vtechcanada.com or dial 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save you a service call.

Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling

charges incurred in the transport of the Product(s) to the service location. VTech will return replaced Product under this limited warranty. Transportation,

delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does

not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of replacement prior to any further replacement

activity. You must pay for the cost of replacement and return shipping costs for the replacement of Products that are not covered by this limited warranty.

What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or

difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and

3. Provide your name, complete and correct mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product.

VTech provides no other warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no

other express warranties. No one is authorized to make modiﬁcations to this limited warranty and you should not rely on any such modiﬁcation.

State/Provincial Law Rights: This warranty gives you speciﬁc legal rights, and you may also have other rights, which vary from state to state or province to

province.

Limitations: Implied warranties, including those of ﬁtness for a particular purpose and merchantability (an unwritten warranty that the Product is ﬁt for ordinary

use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you. In no event shall

VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost proﬁts or revenue, inability to use the

Product or other associated equipment, the cost of substitute equipment, and claims by third parties)

resulting from the use of this Product. Some states/ provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of purchase.

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this user’s manual. VTech

Communications, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555

Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

Important safety instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of ﬁre, electric shock and injury, including

the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

4. CAUTION: Do not install the telephone base at a height above 2 meters.

5. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a swimming pool, or in a wet basement or shower.

6. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

7. Avoid placing the telephone system in places with extreme temperature, direct sunlight, or other electrical devices. Protect your phone from moisture,

dust, corrosive liquids and fumes.

8. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To protect them from overheating, these

openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a

radiator or heat register. This product should not be placed in any area where proper ventilation is not provided.

9. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in

your home or ofﬁce, consult your dealer or local power company.

10. Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on.

11. Never push objects of any kind into this product through the slots in the telephone base or handset because they may touch dangerous voltage points

or create a short circuit. Never spill liquid of any kind on the product.

12. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the

telephone base or handset other than speciﬁed access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause

electric shock when the product is subsequently used.

13. Do not overload wall outlets and extension cords.

14. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions:

• When the power supply cord or plug is damaged or frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operation

instructions. Improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore

the product to normal operation.

• If the product has been dropped and the telephone base and/or handset has been damaged.

• If the product exhibits a distinct change in performance.

15. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning.

16. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a spark may be created when the adapter is

plugged into the power outlet, or when the handset is replaced in its cradle. This is a common event associated with the closing of any electrical circuit.

The user should not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the phone is located in an environment

containing concentrations of ﬂammable or ﬂame-supporting gases, unless there is adequate ventilation. A spark in such an environment could create a

ﬁre or explosion. Such environments might include: medical use of oxygen without adequate ventilation; industrial gases (cleaning solvents; gasoline

vapors; etc.); a leak of natural gas; etc.

17. Only put the handset of your telephone next to your ear when it is in normal talk mode.

18. The power adapter is intended to be correctly oriented in a vertical or ﬂoor mount position. The prongs are not designed to hold the plug in place if it

is plugged into a ceiling, under-the-table or cabinet outlet.

19. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

20. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion if a wrong type of battery is used for

the handset. Use only the supplied rechargeable batteries or replacement batteries (BT183642/BT283642) for the handset. Do

not dispose of batteries in a ﬁre. They may explode. Disposed of used batteries according to the instruction.

• Do not use the battery in following conditions:

»High or low extreme temperature during use, storage or transportation.

»Replacement of a battery with an incorrect type that can defeat a safeguard.

»Disposal of a battery into ﬁre or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.

»Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of ﬂammable liquid

or gas.

»A battery subjected to extremely low air pressure that can result in an explosion or the leakage of ﬂammable liquid or gas.

21. Use only the adapter included with this product. Incorrect adapter polarity or voltage can seriously damage the product.

22. The applied nameplate is located at the bottom or near of the product.

SAVE THESE INSTRUCTIONS

Battery

• Use only the batteries provided or equivalent. To order a replacement, visit our website at www.vtechphones.com or call 1 (800) 595-9511.

• In Canada, go to phones.vtechcanada.com or call 1 (800) 267-7377.

• Do not dispose of the battery in a ﬁre. Check with local waste management codes for special disposal instructions.

• Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic

if swallowed.

• Exercise care in handling batteries in order not to create a short circuit with conductive materials.

• Charge the battery provided with this product only in accordance with the instructions and limitations speciﬁed in this manual.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless telephones):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless

telephones and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least six inches from the pacemaker.

• Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is turned ON.

• Should use the wireless telephone at the ear opposite the pacemaker.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless telephones.

About cordless telephones

• Privacy: The same features that make a cordless telephone convenient create some limitations. Telephone calls are transmitted between the telephone

base and the cordless handset by radio waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio receiving

equipment within range of the cordless handset. For this reason, you should not think of cordless telephone conversations as being as private as those

on corded telephones.

• Electrical power: The telephone base of this cordless telephone must be connected to a working electrical outlet. The electrical outlet should not

be controlled by a wall switch. Calls cannot be made from the cordless handset if the telephone base is unplugged, switched off or if the electrical

power is interrupted.

• Potential TV interference: Some cordless telephones operate at frequencies that may cause interference to televisions and VCRs. To minimize or prevent

such interference, do not place the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the

cordless telephone farther away from the TV or VCR often reduces or eliminates the interference.

• Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with conducting material such as rings, bracelets and

keys. The battery or conductor may overheat and cause harm. Observe proper polarity between the battery and the battery charger.

• Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn or puncture the battery. Like other batteries of

this type, if burned or punctured, they could release caustic material which could cause injury.

ECO mode

This power conserving technology reduces power consumption for optimal battery performance. The ECO mode activities automatically whenever the

handset is synchronized with the telephone base.

For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez toujours ces

mesures préventives de base lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les instructions.

2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.

3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de nettoyeurs liquides ni en aérosol. N’utilisez qu’un chiffon doux et

légèrement humecté.

4. ATTENTION: Ne pas installer le socle téléphonique à une hauteur supérieure à 2 mètres.

5. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier de cuisine, d’un bac de lavage ou d’une piscine, ou dans un

soussol humide ou sous la douche.

6. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil pourrait tomber et être sérieusement endommagé.

7. Évitez d’installer le système téléphonique dans les endroits soumis à une température extrême, à la lumière directe du soleil ou à proximité immédiate

d’autres appareils électriques ou électroniques. Protégez votre téléphone contre les sources d’humidité, la poussière, les vapeurs et les liquides

corrosifs.

8. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière ou en dessous. Aﬁn d’empêcher la surchauffe, ces ouvertures ne

doivent pas être obstruées en plaçant l’appareil sur un lit, divan, tapis ou autre surface similaires. Ne placez pas cet appareil proximité d’un élément de

chauffage ni d’une plinthe électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet fermé qui ne possède pas d’aération adéquate.

9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes de l’appareil. Si vous ne connaissez pas le voltage de votre

maison, consultez votre marchand ou votre fournisseur d’électricité.

10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit sécuritaire, là où personne ne pourra trébucher sur la ligne

d’alimentation ni le cordon téléphonique modulaire.

11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient toucher à des points de tension dangereux ou court-circuiter

des pièces, ce qui constituerait un risque d’incendie ou d’électrocution. N’échappez pas de liquides dans l’appareil.

12. Aﬁn de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le plutôt à un centre de service qualiﬁé s’il doit être réparé. En

enlevant le couvercle, vous vous exposez à des tensions dangereuses ou autres dangers similaires. Un remontage inadéquat peut être à l’origine d’une

électrocution lors d’une utilisation ultérieure de l’appareil. Débranchez l’appareil avant de procéder au nettoyage. Utilisez un chiffon humide et doux.

13. Ne surchargez pas les prises de courant et les rallonges.

14. Débranchez cet appareil de la prise de courant et communiquez avec le département de service à la clientèle de VTech dans les cas suivants:

• Lorsque le cordon d’alimentation est endommagé ou écorché. • Si du liquide a été échappé dans l’appareil.

• Si l’appareil a été exposé une source d’humidité telle que la pluie ou l’eau.

• Si le produit ne fonctionne pas normalement en respectant les instructions de fonctionnement. Réglez uniquement les commandes indiquées dans

le les instructions de fonctionnement. Les réglages incorrects des autres commandes pourraient provoquer un dommage qui pourrait exiger un

travail exhaustif de la part d’un technicien autorisé aﬁn de rétablir le fonctionnement normal de l’appareil.

• Si le produit a été échappé et que le socle et/ ou le combiné a été endommagé.

• Si le produit afﬁche une nette diminution de sa performance.

15. Évitez d’utiliser un téléphone (autre qu’un sans ﬁl) pendant un orage. Les éclairs peuvent être à l’origine d’une électrocution.

16. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En certaines circonstances, une ﬂammèche pourrait être provoquée

lorsque l’adaptateur est branché à une prise de courant, ou lorsque le combiné est déposé sur le socle. Ceci est un événement commun associé à

la fermeture d’un circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à une prise de courant, et ne devrait pas déposer le combiné

chargé sur le socle, si le téléphone se trouve à proximité d’un endroit comportant des concentrations de gaz inﬂammables, moins que la ventilation

soit adéquate. Une ﬂammèche dans un tel endroit pourrait provoquer un incendie ou une explosion. De tels environnements peuvent comprendre:

des endroits où l’on utilise de l’oxygène médical sans ventilation adéquate; des gaz industriels (dissolvants de nettoyage, des vapeurs d’essence, etc.);

une fuite de gaz naturel, etc.

17. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de conversation.

18. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au sol. Les broches ne sont pas conçues pour maintenir l’adaptateur

en place si celui-ci est barnché dans une prise au plafond ou sous une table/ armoire.

19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le socle de prise de courant doit etre installe a proximite du materiel et doit etre aisement

accessible.

20. MISE EN GARDE: Il peut y avoir un risque d’explosion si vous utilisez le mauvais type de piles pour le téléphone. N’utilisez que

les piles rechargeable inclus ou les piles de rechange (BT183642/BT283642). N’incinérez pas les piles. Celles-ci risqueraient

d’exploser. Mettre au rebut les batteries usagées conformément aux instructions du fabricant.

• Évite d’utiliser la batterie dans les conditions suivantes:

» des températures extrêmes faibles ou élevées auxquelles une batterie peut être soumise pendant l’utilisation, le stockage ou le transport;

Install | Set up

What’s in the box

Your telephone package contains the following items. Save your sales receipt and original packaging in

case it is necessary to ship your telephone for warranty service.

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

User’s manual

Install the battery

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP

Connect and charge

Battery indicators Battery status Action

• The screen is blank, or

shows Put in charger and

ﬂashes.

• The battery has no charge

or very little charge. The

handset cannot be used.

• Charge without interruption (at

least 30 minutes).

• The screen shows Low

battery and ﬂashes.

• The battery has enough

charge to be used for a

short time.

• Charge without interruption (at

least 30 minutes).

• The screen shows

HANDSET X.

• The battery is charged. • To keep the battery charged,

place it in the handset charger

when not in use.

Overview

Handset

• Press to show the menu options.

• While in the menu, press to select an

item or save an entry or setting.

• Quick access to Smart call blocker.

• During a call, press to hang up.

• While in a menu, press to return to

the previous menu, or press and

hold to return to idle mode, without

making changes.

• Press to delete digits while predialing.

• While the phone is ringing, press to

silence the ringer temporarily.

• Press and hold to erase the missed

call indicator when the handset is

not in use.

• Press to make or answer a call using the

handset speakerphone.

• During a call, press to switch between the

handset speakerphone and the handset

earpiece.

• Press to review the phonebook when

the phone is not in use.

• Press to scroll up while in a menu, or

in the phonebook, caller ID log or

redial list.

• While entering names or numbers,

press to move the cursor to the right

(p) and left (q).

• During a call or message playback,

press to increase (p) or decrease (q)

the listening volume.

• Press to switch to tone dialing during a

call if you have pulse service.

• While entering numbers, press and hold

to insert a dialing pause.

• While entering names, press to change

the next letter to upper or lower case.

• Press repeatedly to view the last 10

numbers dialed.

• When reviewing a caller ID log entry,

press repeatedly to view other dialing

options.

• While reviewing a caller ID log entry,

press repeatedly to add or remove 1 in

front of the telephone number before

dialing or saving it in the Phonebook.

• Press and hold to set or dial your voicemail

number.

• Enter space characer during text

editing.

• Press to make or answer a call.

• During a call, press to answer an incoming

call when you receive a call waiting alert.

• During a call, press to mute the

microphone.

• While the phone is ringing, press to

silence the ringer temporarily.

• While reviewing the redial list,

directory or caller ID log, press to

delete an individual entry.

• While predialing, press to delete

digits.

• Press to make, answer or end a cell call.

Base

• Press to turn the answering system on

or off.

• Press to delete the playing message.

• Press twice to delete all old messages

when in idle.

• Press to page the system handset.

• Press to increase the listening volume

during a call or message playback.

• Press to increase the telephone base

ringer volume when the base is not in use.

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

12 hrs

Go to www.vtechphones.com (US) to register

your product for enhanced warranty support

and latest VTech product news.

Go to phones.vtechcanada.com (Canada) for

the latest VTech product news.

Speciﬁcations are subject to change without notice.

VS122-16_QSG_V1.0

NOTES

• If you have subscribed to caller ID service, then you can use the Smart

call blocker feature to screen incoming calls.

• The screening feature of Smart call blocker is applicable to incoming

home calls only. All incoming cell calls will get through and ring. If you

want to block a cell call, add the number to the block list.

Turn Smart call blocker on or off

Smart call blocker is set to on and allows all incoming calls by default. To turn

on or off Smart call blocker:

1. Press to enter the main menu in idle.

2. Press p/q to scroll to Smart call blk, and then press .

3. Press p/q to scroll to SCB On/Off, and then press .

4. Press p/q to scroll to On or Off, and then press .

• If you turn off Smart call blocker, all incoming calls will ring, including

those in your block list.

Set up allow list/ block list/ start name list

Add numbers manually

1. Press to enter the main menu in idle.

2. Press p/q → Smart call blk → .

Adding a new

number to the

block list

3. Press p/q → Block list → .

4. Press p/q → Add new entry → .

5. Enter a telephone number (up to 30 digits),

and then press .

6. Enter a name (up to 15 characters), and then

press .

• Repeat Step 4 to add another contact.

Adding a new

number to the

allow list

3. Press p/q → Allow list → .

4. Press p/q → Add new entry → .

5. Enter a telephone number (up to 30 digits),

and then press .

6. Enter a name (up to 15 characters), and then

press .

• Repeat Step 4 to add another contact.

Adding a new name

to the star name list 3. Press p/q → Star name list → .

4. Press p/q → Add new entry → .

5. Enter a name (up to 15 characters), and then

press .

• Repeat Step 4 to add another contact.

Add numbers from caller ID log

1. Press to enter the caller ID log in idle.

2. Press p/q to locate the desired entry → .

Adding CID log entry

to block list 3. Press p/q → To Block list → .

4. Press twice.

Adding CID log entry

to allow list 3. Press p/q → To Allow list → .

4. Press twice.

Adding a new name

to the star name list 3. Press p/q → To Star name list → .

4. Press twice.

Call controls

Call categories Call control and

options

Unwelcome

calls

Numbers saved in

block list.

The telephone blocks these

calls from ringing through.

Welcome calls

• Numbers saved in

allow list.

• Numbers saved in

phonebook.

• Numbers not found

in block list.

• Caller ID names

saved in start name

list.

The telephone allows these

calls to get through and

ring.

All incoming cell calls will

get through and ring by

default. If you want to block

a cell call, then you need

to add its number to the

block list.

Call categories Call control and

options

Unknown calls

(for home calls

only)

Calls without numbers

• Numbers that are

“out of area” or set

to “Private”.

You can select one of

the following ﬁve proﬁle

options for handling all

unknown home calls.

Screen unknown

The telephone plays the

screening announcement,

and then ask the caller to say

his/her name before the call

rings on your telephone.

You can then answer the

call, and hear the caller’s

name announced. You

can decide whether to

accept or reject the call, or

to forward the call to the

answering system.

Screen robot

The telephone plays the

screening announcement,

and then ask the caller to

press the pound key (#)

before the call rings on your

telephone. You can then

answer the call.

Allow unknown

(default settings)

The telephone allows these

calls to get through and

ring. The caller’s number,

even if it is available, will not

be saved to the allow list.

Unknown to answering

system

The telephone forwards

these calls to the answering

system without ringing.

Block unknown

The telephone rejects

these calls with block

announcement without

ringing. The caller’s number,

even if it’s available, will not

be saved to the block list.

Uncategorized calls

• With absent caller

ID number.

• Numbers not found

in phonebook.

• Numbers not found

in allow list.

• Numbers not found

in block list.

• With caller ID

names not found in

star name list.

Set proﬁle

There are 5 proﬁle setting options, which allows you to quickly set up Smart

call blocker.

1. Press to enter the main menu in idle.

2. Press p/q → Smart call blk → .

3. Press p/q → Set proﬁle → .

Set proﬁle Steps

Screen unknown

Screen all unknown home calls

4. Press p/q→ Screen

unknown → .

Screen rebot

Screen robocalls

4. Press p/q→ Screen robot

→ .

Allow unknown

Block calls on the block list

only (default setting)

4. Press p/q→ Allow

unknown → .

UnknowntoAns.S

Forward all unknown home

calls to the answering system

4. Press p/q→

UnknowntoAns.S→ .

Block unknown

Block all unknown home calls

4. Press p/q→ Block

unknown → .

Add a screened number to the block list or allow list

If you select Screen unknown or Screen robot in Set proﬁle, the telephone

plays a screening announcement to the caller, and asks the caller to respond

before the call rings through to you. After the caller responds, the telephone

rings and you can then pick up the call. The telephone then asks whether

you want to answer or reject the call, or to forward the call to the answering

system. The telephone announces “To answer the call, press 1. To answer and

always allow this number, press 2. To block this number, press 3. To send this

call to the answering system, press 4. To repeat these options, press *”.

Add current number

to the allow list

Press 2 to answer the home call, and add

the current number to the allow list.

Add current number

to the block list

Press 3 to block the home call, and add

the current number to the block list.

• This is applicable to home calls only. All incoming cell calls will get through

and ring.

• Unknown home calls without caller ID information will not have the option

2, “answer and always allow this number”, and option 3, “to block this

number”. No number will be added to the allow list or block list for these

calls.

• If you do not want to take the call, press to end the call.

Block the caller while on a call

When you are on a home or cell call and speaking to the caller, and

you do not want to continue the call, you can end the call with block

announcement and add the number to the block list. During a home

or cell call, press → .

Unblock a telephone number

If you have added a telephone number to the block list, you can

unblock it.

1. Press → p/q → Block list → .

2. Press to choose Review, and then press p/q to browse

through the block entries.

3. When the desired entry displays, press on the handset. Then,

press to conﬁrm.

Caller ID

If you subscribe to caller ID service, information about each caller

appears after the ﬁrst or second ring. The caller ID log stores up to 50

entries. Each entry has up to 24 digits for the phone number and 15

characters for the name.

Review caller ID log entries

Press →p/q to browse the entries.

Save a caller ID log entry to the phonebook

1. Press →p/q to scroll to your desired caller ID entry.

2. Press → to choose To Phonebook.

3. Edit the number if needed, and then press .

4. Edit the name if needed, and then press .

Dial a caller ID log entry

1. Press →p/q to scroll to your desired caller ID entry.

2. Press / / to dial.

Delete a caller ID log entry

1. Press →p/q to scroll to your desired caller ID entry.

2. Press (handset) or (base).

Phonebook

The phonebook can store up to 1,000 entries, which are shared by

all handsets and the telephone base. Each entry may consist of a

telephone number up to 30 digits, and a name up to 15 characters.

Add a phonebook entry

1. Press to enter the main menu in idle.

2. Press p/q → Phonebook → .

3. Press to select Add new entry.

4. Enter the number, and then press . Enter the name, and then

press .

Review phonebook entries

Press → p/q to review phonebook entries.

Dial a phonebook entry

When your desired entry displays, press / / to dial.

Delete a phonebook entry

When your desired entry displays, press (handset) or

(base). Press to conﬁrm.

Answering system

About answering system and voicemail

For message recording, your telephone has a built-in answering

system, and it also supports voicemail service offered by your

telephone service provider (subscription is required, and fee may

apply).

Built-in answering

system Voicemail service

Supported

by Telephone system Telephone service

provider

Subscription No Yes

Fee No May apply

Answer

incoming

calls

• After 4 rings by

default.

• It can be changed in

the handset or the

telephone base menu.

• Usually after 2

rings.

• It can be changed

by contacting your

telephone service

provider.

Storage Telephone base Server or System

Display new

messages

• Handset - XX new

messages

• Telephone base - XX.

If message alert tone

is turned on, the

base beeps every 10

seconds.

• Handset -

Retrieve

messages

• Press on the

base;

• Press and then

select Play messages

on the handset; or

• Access remotely with

an access code.

• Press on the

handset, and

enter an access

number from your

telephone service

provider.

Turn on/off built-in answering system

Handset Base

1. Press to enter the main menu in idle.

2. Press p/q → Answering sys → .

3. Press p/q → Answer on/off → .

4. Press On/Off.

Press (base).

Message playback

Handset Base

Press → to select Play messages.Press (base).

Options during message playback

Skip a message Repeat the

playing message

Play the previous

message

Press 6 (Handset) or

(base). Press 4 (Handset)

or (base).

Press 4 twice

(Handset) or

twice (base).

Set number of rings

You can set your answering system to answer calls at least two rings

earlier than your voicemail service. For example, if your voicemail

service answers after six rings, set your answering system to answer

after four rings. In case you are on a call, or if the answering system is

busy recording a message and you receive another call, the second

caller can leave a voicemail message.

1. Press to enter the main menu in idle.

2. Press p/q → Answering sys → .

3. Press p/q → Ans sys setup → .

4. Press p/q → # of rings → .

5. Press p/q to scroll to desired number of rings → .

Delete all messages

1. Press to enter the main menu in idle.

2. Press p/q → Answering sys → .

3. Press p/q → Delete all old → .

• Light on when the

bluetooth device is

paired and active.

• Flashes when bluetooth

is activated and ready

to pair.

• Press to decrease the

listening volume during a

call or message playback.

• Press to decrease the

telephone base ringer

volume when the base is

not in use

• Light on when the

bluetooth device is

paired and active.

• Flashes when bluetooth

is activated and ready

to pair.

• Press to skip to the next

message.

• Press to repeat the

playing message.

• Press twice to play the

previous message.

• Press to play messages.

• Press to stop playing

messages.

Handset display icons

• The handset battery is low and needs charging.

• The handset battery is charging.

• The handset battery is fully charged.

ECO • The ECO mode activates automatically to reduce

power consumption when the handset is within

range of the telephone base.

• New voicemail received from your telephone

service provider.

• Displays when Home line is in use.

• Bluetooth device is paired and active.

• Bluetooth device / Cell line is in use.

NEW

• There are new caller ID log entries

ANS ON • Answering system is on.

10:30PM • Time with AM and PM.

• Handset ringer is off.

10/16

MSG # • Handset displays the current message number

being played and the total number of new/old

messages recorded.

Base display

• Flashes quickly when there is an incoming call.

• Flashes when another telephone sharing the line is

in use.

• On when the line is in use.

• On when the handset is charging in the telephone

base or charger.

• Shows the number of messages, and other

information of the answering system or telephone

base.

Conﬁgure your phone

Set the date and time

1. Press to enter the main menu in idle.

2. Press p/q to scroll to Set date/time, and then press .

3. Press p/q to scroll to select the month, and then press .

4. Press p/q to scroll to select the date, and then press .

5. Press p/q to scroll to select the year, and then press .

• You can also use dialing keys to enter 2-digit number for month, date,

and year.

6. Press p/q to scroll to select the hour, and then press .

7. Press p/q to scroll to select the minute, and then press .

8. Press p/q to scroll to select AM or PM.

9. Press to save the settings.

Set handset LCD language

1. Press to enter the main menu in idle.

2. Press p/q to scroll to Settings, and then press .

3. Press again to select LCD language.

4. Press p/q to scroll to English, Français or Español, and then press .

5. Press to save your selected language.

• If you accidentally change the LCD language to French or Spanish, you

can reset it to English easily by pressing MENU then entering 364 .

Set handset ringer

1. Press to enter the main menu in idle.

2. Press p/q to scroll to Ringers, and then press .

3. Press p/q to scroll through Home volume, Home ringtone, Cell volume,

and Cell ringtone.

Ringer volume

After you selected Home volume or Cell volume:-

• Press p/q to adjust the volume level, and then press .

• If you want the Ringer off, press q all the way till you see .

Ringertone

After you selected Home ringtone or Cell ringtone:-

• Press p/q to select your preferred ringtone among 10 melodies.

• Press to save.

Bluetooth

Setup

To use a Bluetooth enabled cell phone with your VS122-16, you must ﬁrst pair

and connect it with the telephone base. The VS122-16 telephone base and all

system handsets can be used to make or answer calls on the cell phone line.

Bluetooth wireless technology operates within a short range (a maximum of

approximately 30 feet). When you pair a Bluetooth cell phone to the telephone

base, make sure your Bluetooth cell phone is close to the telephone base to

maintain sufﬁcient signal strength. For optimal performance, keep your cell

phone within 15 feet of the telephone base while using the cell line.

Add a cell phone

1. Press and hold or on the base to activate Bluetooth pairing.

• The light starts ﬂashing when the base is ready to pair.

2. Turn on the Bluetooth of your cell phone to scan for VTech DECT 6.0.

• Your cell phone will prompt and ask you whether to pair with it. Press

OK to conﬁrm.

• Once paired, the light of or on the base illuminate, and or

displays on the handset.

The steps for the pairing process may vary for different cell phones. If this

happenes, follow the prompts on your cell phone and your VS122-16 to

complete the pairing process.

Auto connection

Cell phone(s) may disconnect from the base when:-

• Your cell phone’s Bluetooth feature is off.

• Your cell phone is power off.

• Your cell phone is out of range from the telephone base.

Make sure your cell phone and its Bluetooth feature is on, then move it closer

to the base. The base will reconnect automatically.

Review cell device list

1. Press to enter the main menu in idle.

2. Press p/q to scroll to Bluetooth, and then press .

3. Press p/q to scroll to Device list, and then press .

Download phonebook

You can download up to 1000 entries from your cell phone’s phonebooks

to VS122-16. Each entry are stored in the handset phonebook with up to 30

digits for each phone number and 15 characters for each name. Make sure

your cell phone is paired anc connected to the base, and the handset battery

is charged for at least 10 minutes. Place your cell phone next to the base

while downloading.

Download a cell phone phonebook

1. Press to enter the main menu in idle.

2. Press p/q to scroll to Bluetooth, and then press .

3. Press p/q to scroll to Download PB, and then press .

• Select a device displays brieﬂy.

4. Press p/q to scroll to your preferred device, and then press .

• During the download, the handset ﬂashes Downloading....

• When the process is complete or when the memory is full, the handset

displays Entries added: XXX.

TIPS

• Certain cell phones do not support SIM card download. If this is the

case, try transferring the contacts from your SIM card to your cell phone

memory ﬁrst, then download from your cell phone memory. For more

information on how to transfer contacts from your SIM card to your cell

phone memory, see the user’s manual of your cell phone.

• When downloading the directory from your Bluetooth enabled cell

phone, some data may not transfer. For example, if you have home,

mobile and work numbers for a particular contact, the three categories

may not transfer to your VS122-16.

• For certain cell phones, you may need to press a key on your cell phone

to conﬁrm the directory download.

Smart call blocker* (SCB)

Smart call blocker ﬁlters robocalls and unwanted calls for you, while allowing

welcome calls to get through. For other unknown home calls, you can block,

screen, or forward these calls to the answering system.

With Call screening active, Smart call blocker screens and ﬁlters all incoming

home calls from numbers or names that are not saved in your Phonebook,

Block list, or Star name list. You can easily add incoming phone numbers to

your Block list. This allows you to build up your lists of allowed and blocked

numbers, and Smart call blocker will know how to handle these calls when

they call again.

VTech VS122-16 DECT6.0 Cordless Phone Manuel utilisateur

Marque: VTech

Modèle: VS122-16 DECT6.0 Cordless Phone

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

VS122-16

Télécharger le PDF

rapport

dans d''autres langues

English: VTech VS122-16 DECT6.0 Cordless Phone User manual

VTech VS122-16 DECT6.0 Cordless Phone Manuel utilisateur

Ce manuel convient également à

VTech VS122-16 DECT6.0 Cordless Phone Manuel utilisateur

dans d''autres langues

Documents connexes