Kärcher G 3000K Manuel utilisateur

English. . . . 4

Español . . . 22

Français. . . 42

8.641-537.0-C 01/17

G 3000K

1. Spray Gun

2. Nozzles

3. Muffler

4. Air Filter

5. Choke and Throttle Lever

6. Detergent Tank Cap

7. Detergent Tank

8. Fuel Tank Cap

9. Fuel Tank

10. Hand Cord

11. Oil Dipstick

12. Pressure Hose

13. Detergent Suction Connection

14. Pump Outlet

15. Pump Inlet

16. Thermal Relieve Valve

17. Spark Plugs

G 3000 K Parts List

1

2

3

12

13

14

15

16

17

4

8

9

11

10

5

6

7

4 English

Please read and

comply with these

original instruc-

tions prior to the

initial operation of your appliance and

store them for later use or subsequent

owners.

Indicates “an imminently hazardous

situation which, if not avoided, will

result in death or serious injury.”

Indicates “a potentially hazardous

situation which, if not avoided, could

result in death or injury.”

Indicates “a potentially hazardous

situation which, if not avoided, may

HIGH PRESSURE WASHER OPERATOR MANUAL

Contents

Model Overview EN-2

Safety Instructions EN-5

Assembly Instructions EN-7

Preparation EN-9

Operating Instruction EN-10

Using the Accessories EN-12

Working with Detergents EN-13

Taking a Break EN-14

Shutting Down & Clean Up EN-14

Winterizing & Long Term

Storage

EN-14

Maintenance Instructions EN-15

Cleaning Tips EN-15

Troubleshooting EN-18

Specifications

G 3000 K

Operating Pressure 3000 psi

Water Volume 2.5 gpm

Engine OHV

Fuel Type Unleaded Gas

Fuel Tank Size .55 Gallons

(2.1L)

Engine Oil Type SAE 10W-30

Engine Oil Capacity .63 US QT

(.6L)

Model Number 1.107-284.0

Serial Number

Hazard Levels

English 5

result in minor or moderate injury or in

property damage incidents.”

When using this product, basic

precautions should always be

followed, including the following:

●Read the operating instructions of the

engine manufacturer before start-up

and follow the safety instructions

carefully.

●Read all instructions before using

product.

●To reduce the risk of injury, close

supervision is necessary when the

product is used near children.

●Know how to stop the product and

bleed pressures quickly. Be

thoroughly familiar with the controls.

●Stay alert - watch what you are doing.

●Do not operate when fatigued or

under the influence of alcohol or

drugs.

●Keep operating area clear of all

persons.

●Do not overreach or stand on

unstable support. Keep good footing

and balance at all times.

●Wear safety goggles and ear

protection.

●Follow the maintenance instructions

specified in the manual.

●To avoid risks, all repairs and

replacement of spare parts should

only be carried out by trained

personnel.

●Tire pressure should not exceed max.

25 psi.

Risk of injection or injury – Do not

direct discharge stream at persons.

●High pressure jets can be dangerous

if misused. The jet must not be

directed at persons, animals,

electrical devices, or the unit itself.

Do not spray electrical connections,

electrical outlets or fixtures.

●Do not use acids, solvents, or any

alkaline or flammable material in this

product. These products can cause

physical injuries to the operator and

irreversible damage to the machine.

Gun kicks back – Hold with both

hands.

●The trigger gun safety lock prevents

the trigger from accidentally being

engaged. This safety feature must be

engaged when replacing nozzles or

not in use.

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

Operation of this equipment may

create sparks that can start fires

around dry vegetation. A spark

arrestor may be required. Operator

should contact local fire agencies for

laws or regulations.

Safety Instructions

6 English

Running this product indoors can

result in death due to carbon monox-

ide, a poison gas you cannot see or

smell. Never operate indoors, even if

windows and doors are open. Only

use outdoor and far away from win-

dows, doors, and openings or vents.

Risk of asphyxiation – Use this

product only in a well ventilated area.

Do not operate indoors or in any

confined area.

●Operate and fuel machine in a well

ventilated area, free of devices

featuring an open pilot or flame such

as boilers, water heaters, etc.

Risk of fire/explosion – Do not add fuel

when the machine is operating or still

hot.

Risk of fire/explosion -Operate only

where open flame or torch is

permitted. Do not spray flammable

liquids.

●Do not operate if fuel has been

spilled. Instead, move machine to

different location and avoid creating

sparks.

●This machine has hot surfaces which

can cause burns. Operate in a safe

environment and away from children.

●Do not touch hot surfaces or allow

accessories to contact hot surfaces.

●Do not leave machine running

unattended.

●Avoid tipping machine on its side.

Starter cord kickback (rapid retraction)

can result in bodily injury. Kickback will

pull hand and arm toward engine

faster than you can let go. ALWAYS

relieve spray gun pressure before pull-

ing starter cord. Pull starter cord

slowly until resistance is felt, then pull

rapidly.

When connecting to water supply

mains, local regulations of your

municipal water company must be

observed. In some areas connecting

directly to public drinking water supply

may require a back flow prevention

device. This is to ensure that there is

no feedback of chemicals into the

water supply. Use a water filter to

avoid potential damage from dirt in the

water supply.

●Garden hose must be at least 5/8

inch diameter.

●Flow rate of water supply must not

fall below 2.5 GPM

(gallons per minute)

●Flow rate can be determined by

running the water for one minute into

an empty 5-gallon container.

●The water supply temperature must

not exceed 122°F/50°C.

Water Supply

(Cold Water Only)

English 7

●Never use the pressure washer to

draw in water contaminated with

solvents, e.g. paint thinners,

gasoline, oil, etc.

●Always prevent debris from being

drawn into the unit by using a clean

water source. Use additional water

filter.

●Do not operate pressure washer

without the water turned on.

●Use only approved pressure washer

detergent.

A - Main Frame

B - Handle

C - Gun Hook & Hose Hook

D - Knobs & Bolts

E - Pressure Hose

Assembly Instructions

Part List

8 English

F - Spray Gun & Wand

G - Wheels

Parts not shown:

1 - Manual

1 - Nozzle Cleaner

1 - Spark Plug Wrench

1 - O-Ring Set

(2 for pressure hose, 1 for spray gun)

1. Install the wheels to the main frame

by pressing the spring loaded pin on

wheel axle, then insert wheel axle

into frame. Ensure that the spring pin

is fixed in position. Repeat for the

other wheel.

2. Attach the handle and main frame

with knobs and bolts.

Assembling

English 9

3. Attach the gun & hose hooks to the

handle.

Engine shipped without oil in

crankcase. Before starting engine, fill

with oil. Do not over-fill. Do not run the

engine wizth a high or low oil level as

this can cause engine damage. If you

have further questions regarding the

engine, please refer to the engine

manual included with the unit.

1. Turn the oil gauge dipstick counter

clockwise; remove it and clean it with

a clean cloth.

2. Fully reinsert the oil gauge dipstick

and pull it out to check the oil level.

3. If the oil level is halfway up the

dipstick or below, refill with SAE 10W-

30 oil through the dipstick hole until

the oil level reaches 3/4 up the dip-

stick or until it reaches the bottom lip

of the dipstick hole as shown.

Always use SAE 10W-30 oil.

Oil crankcase capacity: 0.6L.

4. Reposition the oil gauge dipstick and

tighten it by turning clockwise.

5. Engine oil should be changed after

the first 5 hours, then every 50 hours.

Make sure there is enough fuel in the

fuel tank before operating. This is a

4-cycle engine and does not require a

gas/oil mixture. There is a separate

reservoir for gas and a separate

reservoir for oil.

Preparation

Oil Level

Fuel Level

10 English

►If it is necessary to add fuel, first

make sure the engine is OFF, and

then remove the fuel cap by turning it

counter clockwise.

►When refueling, make sure the fuel

filter is in place and keep in mind all

safety precautions.

►Use clean unleaded gasoline with a

minimum of 87 octane. DO NOT use

old gas. DO NOT mix oil with

gasoline.

Fuel tank capacity: .55 Gallons

(2.1L)

The air filter should be checked after

prolonged storage, the following steps

should be done when checking the air

filter. It is recommended to replace the

air filter once every spring.

1. Press the right side of air cleaner

housing and take it down.

2. Remove the air filter, wash filter in

kerosene, squeeze kerosene out,

soak filter in engine oil and squeeze

engine oil out.

3. Replace filter and replace the air filter

cover.

►Starting Procedure:

1. Connect garden hose.

Air Filter

Operating Instructions

PRESS

English 11

2. Connect spray gun and pressure

hose.

3. Open water source.

►Start the Engine.

1. Turn the throttle lever to "CHOKE"

position.

2. Pull trigger on spray gun to release

pressure.

3. Locate recoil cord and pull slowly

until resistance is felt. At this point,

pull rapidly to start engine.

4. After the engine has started, turn the

throttle lever to "FAST" position.

NOTE: If unable to start the engine,

repeat the above operation one or two

times.

NOTE: If the temperature is higher,

such as during summer or if the engine

is hot, choke valve should be switched

to “FAST” position before starting.

STOP

12 English

►Cleaning Procedure:

1. Position the tip of the wand 6-8”

(15-20 cm) away from the surface to

clean at a 45°angle.

The color-coded quick connect

nozzles provide a wide array of spray

widths from 0° to 65° and are easily

accessible when placed in the

convenient nozzle holder.

0° spray angle = Red nozzle

For particularly stubborn accumulation

of grime. Not recommended for soft

materials like sidings, decks, painted

surfaces, cars.

15° spray angle = Yellow nozzle

For dirt accumulation over a surface.

25° spray angle = Green nozzle

For dirt accumulation over a large

surface.

40° spray angle = White nozzle

For moderate dirt accumulation over a

large surface.

Soap = Black nozzle

For operating with detergents or

cleaning with low pressure.

High pressure in nozzle area. Risk of

injury caused by improperly locked

nozzle.

●Make sure you hear the "click" when

inserting the nozzle tip into the quick

connection.

●Pull the nozzle to make sure it is

seated properly before operating your

unit.

To avoid serious injury never point

spray nozzle at yourself, other

persons or animals.

The pressure can be adjusted by

changing the speed of the engine

using the throttle lever.

Turning the throttle lever to the left can

increase the speed to get more

pressure.

Using the Accessories

Quick Connect Nozzles

Adjusting Water Pressure

English 13

Turning the throttle lever to the right

can decrease the speed to get less

pressure.

When adjusting the engine throttle to

the lowest setting, do not operate the

pump. This can cause the engine to

stall due to lack of power.

NOTE: Detergents can only be applied

with the black detergent nozzle.

1. Install the black detergent nozzle for

detergent application at low pressure.

2. Fill the detergent tank with Kärcher

Brand Detergent.

3. With the engine running, pull trigger

to operate unit.

4. Liquid detergent is drawn into the unit

and mixed with water.

5. Apply detergent to work area.

6. Do not allow detergent to dry on

surface.

7. Always flush the detergent bottle with

fresh water when the cleaning job is

done, to rinse/flush any remaining

detergents from the injection system.

NOTE: For best results see Cleaning

Tips for specific information on how to

clean different surfaces.

This unit has been designed for use

with cleaning detergents

recommended by the manufacturer.

The use of other cleaning detergent

may affect the operation of the

machine and void the warranty.

Always Use Kärcher Detergent for

Best Results.

Kärcher biodegradable detergents are

specially formulated to protect the

environment and your pressure

washer. The special formula won't

clog the filter and will protect the

internal parts of the pressure washer

for a longer life. For Kärcher

Detergents, check your retailer or visit

our website:

www.karcherresidential.com

Never use:

●Bleach, chlorine products or other

corrosive chemicals.

●Liquids containing solvents (i.e., paint

thinners, gasoline, oils.)

●Tri-sodium phosphate products.

●Ammonia products.

●Acid-based products.

These chemicals will harm the unit

and will damage the surface being

cleaned.

Use of these items will void the

warranty.

Working with Detergents

Detergent Tank

14 English

1. Move the throttle lever to “STOP”

position.

For engine details see engine

manual.

2. Release trigger and engage safety

lock.

1. If detergents have been used, insert

1 gallon of fresh water into Detergent

Bottle. Siphon water at low pressure

for one minute to clear the line of

residual detergent.

2. Move the engine stop switch to the

OFF position. Close the fuel valve.

3. Turn off the water source.

4. Press trigger to release water

pressure.

5. Release trigger and engage gun

safety lock.

6. Disconnect the garden hose from the

water inlet on the unit.

7. Disconnect the high pressure hose

from the high pressure outlet. Store

the high pressure hose in the gun

holder assembly.

It is highly recommended to use

Kärcher Pump Guard (part number

9.558-998.0) before winter storage

and during the cleaning season to

protect the pump from freezing and

premature wear.

1. Turn engine switch to the OFF

position.

2. Disconnect all hoses.

3. Unscrew cap from Pump Guard

bottle.

4. Remove internal seal.

5. Reattach cap to Pump Guard bottle

and remove black protective cap.

6. Screw bottle into water inlet on

pressure washer pump and squeeze.

7. With ignition OFF, pull starter rope

until fluid starts to exit.

8. Unscrew bottle. Store or dispose

properly.

►If Kärcher Pump Guard is

unavailable, perform the following:

1. Disconnect all water connections.

2. Turn on the machine for a few

seconds, until the water which

remained in the pump exits. Turn off

engine immediately.

Failure to follow the above directions

may result in damage to the pump

assembly and accessories and void

the warranty.

Do not allow high pressure hose to

become kinked.

Store machine and accessories in a

room which does not reach freezing

temperatures. DO NOT store near

furnace or other sources of heat as it

may dry out the pump seals.

Taking a Break

...five minutes or more

Shutting Down

& Clean Up

Winterizing & Long-Term

Storage

English 15

Pump Inspection

You should routinely make a visual

inspection of the pressure washer’s

pump. If you notice oil leaking around

the pump seals, you should take the

pressure washer to a Kärcher Autho-

rized Service Center for repair.

(You can locate a service center in

your area online at:

www.karcher-service.com).

Carry out maintenance tasks for the

engine according to the specifications

provided in the operating instructions

provided by engine manufacturer.

With or Without Detergent

Pre-rinse deck and surrounding area

with fresh water. If using Kärcher Deck

Wash, apply to surface at low pres-

sure. For best results, limit your work

area to smaller sections of approxi-

mately 25 square feet. Allow Deck

Wash to remain on surface 1-3 min-

utes. Do not allow detergent to dry on

surface. Rinse at high pressure in a

long sweeping motion keeping the

spray nozzle approximately 3-6 inches

from the cleaning surface. Always

clean from top to bottom and from left

to right. When moving on to a new

section of the cleaning surface, be

sure to overlap the previous section to

eliminate stop marks and ensure a

more even cleaning result.

With or Without Detergent

Pre-rinse vehicle with fresh water. If

using Kärcher Touchless Vehicle

Wash, apply to surface at low pres-

sure. For best results, clean one side

of vehicle at a time and always apply

detergent from bottom to top, do not

allow detergent to dry on surface. If

needed, use special wash brush

attachment (not included) to remove

stubborn dirt. Rinse at high pressure

in a sweeping motion keeping the

spray nozzle approximately 6-8 inches

from the cleaning surface (distance

should increase when rinsing pin-

striping or other sensitive surfaces).

Always clean from top to bottom and

from left to right. For best results, wipe

surface dry with a chamois or soft dry

cloth.

Maintenance Instructions

Pump

Engine

Cleaning Tips

Deck Cleaning

Cars, Boats

& Motorcycles

16 English

With or Without Detergent

Pre-rinse cleaning surface with fresh

water. If using Kärcher Pressure

Wash, apply to surface at low pres-

sure (for best results, limit your work

area to sections of approximately 6

feet and always apply detergent from

bottom to top). Allow detergent to

remain on surface 1-3 minutes. Do not

allow detergent to dry on surface, if

surface appears to be drying, simply

wet down surface with fresh water. If

needed, use special wash brush

attachment (not included) to remove

stubborn dirt. Rinse at high pressure

from top to bottom in an even sweep-

ing motion keeping the spray nozzle

approximately 6 inches from the

cleaning surface.

With or Without Detergent

Pre-rinse cleaning surface with fresh

water. If using Kärcher Pressure Wash

or Degreaser, apply to surface at low

pressure. For best results, limit your

work area to smaller sections of

approximately 25 square feet. Allow

Pressure Wash or Degreaser to

remain on surface 1-3 minutes. Do not

allow detergent to dry on surface.

Rinse at high pressure in a sweeping

motion keeping the spray nozzle

approximately 3-6 inches from the

cleaning surface. Always clean from

top to bottom and from left to right. For

removing extremely stubborn stains,

use a DirtBlaster® Spray Nozzle (sold

separately).

With or Without Detergent

Pre-rinse cleaning surface with fresh

water. If using Kärcher Pressure Wash

or Degreaser, apply detergent at low

pressure. Allow Pressure Wash to

remain on surface 1-3 minutes. Do not

allow detergent to dry on surface.

Rinse at high pressure keeping the

spray nozzle approximately 3-6 inches

from the cleaning surface. For remov-

ing extremely stubborn dirt, it may be

necessary to move the spray nozzle

even closer to the surface for greater

dirt cutting action.

With or Without Detergent

Pre-rinse furniture and surrounding

area with fresh water. If using Pres-

sure Wash, apply to surface at low

pressure. Allow Pressure Wash to

remain on surface 1-3 minutes. Do not

allow detergent to dry on surface. If

needed use special Wash Brush

Attachment (not included) to remove

stubborn dirt. Rinse at high pressure

in a sweeping motion keeping the

spray nozzle approximately 3-6 inches

from the cleaning surface. For best

results, clean from top to bottom and

from left to right.

House Siding

Cement Patios, Brick &

Stone

Barbecue Grills, Outdoor

Power Equipment

& Gardening Tools

Patio & Lawn Furniture

English 17

●Before cleaning any surface, an

inconspicuous area should be

cleaned to test spray pattern and dis-

tance for maximum cleaning results.

●If painted surfaces are peeling or

chipping, use extreme caution as

pressure washer may remove the

loose paint from the surface.

●When using on surfaces which might

come in contact with food, flush sur-

faces with plenty of drinking water.

●For additional cleaning tips, visit our

website at

www.karcherresidential.com

Optional accessories are available to

further enhance your cleaning

capabilities. These accessories are

accurate as of the printing date of this

manual. Please check our website:

www.karcherresidential.com for

pricing and up to date information.

●Extension Hose

●DirtBlaster® Spray Nozzle

●Universal Wash Brush Kit

Recommendations

Optional Accessories

18 English

Remove the spark plug cable to pre-

vent accidental ignition of the engine

before making any repair.

Troubleshooting

Symptom Cause Solution

Engine Will Not

Start

No Gasoline. Fill Gas Tank.

Choke is not in the

correct position.

Slide lever out to closed position.

Ignition switch is

not in the correct

position.

Turn Ignition switch on.

Water pressure built

up in the machine.

Squeeze the trigger to release the

pressure.

For additional engine problems refer to the engine

manual.

Unit Does Not

Reach High

Pressure

Diameter of garden

hose is too small.

Replace with a 5/8 inch or larger garden

hose.

Water supply is

restricted.

Check garden hose for kinks, leaks and

blockage.

Not enough inlet

water supply.

Turn water on full force. Check garden

hose for kinks, leaks or blockage.

Water inlet filter is

clogged.

Remove filter and rinse out in warm

water.

Black detergent

nozzle is attached.

Remove black detergent nozzle and

attach high pressure nozzle.

Output Pres-

sure Varies

High And Low

Not enough inlet

water supply.

Turn water on full force. Check garden

hose for kinks, leaks or blockage.

English 19

Output

Pressure

Varies Between

High And Low

Pump is sucking air. Check that hoses and fittings are air

tight. Turn off machine and purge pump

by squeezing trigger gun until a steady

flow of water emerges through the

nozzle.

Water inlet filter is

clogged.

Remove filter and rinse out in warm

water.

Spray nozzle is

obstructed.

Blow out or remove debris with a fine

needle.

Calcified gun, hose

or spray wand.

Run distilled vinegar through detergent

tank.

No Detergent Detergent suction

tube not properly

connected to the

machine.

Check connection.

Detergent is too

thick.

Dilute detergent, for best results use

Kärcher detergent.

Filter on detergent

suction tube is

clogged.

Run warm water through filter to remove

debris.

Damaged or

clogged detergent

suction tube.

Remove obstruction or replace detergent

suction tube.

A high pressure

nozzle is attached.

Replace with black detergent nozzle.

Spray nozzle is

obstructed.

Blow out or remove debris with fine

needle.

Garden Hose

Connection

Leaks

Loose fittings. Tighten fittings.

Missing/worn

rubber washer.

Insert new washer.

Symptom Cause Solution

20 English

If the symptom you are experiencing

is not listed above, or if the provided

solutions do not solve your issue,

please visit our extensive online

troubleshooting database at:

www.karcher-help.com

Spray Wand

Leaks

Spray wand not

properly attached.

Turn the swivel nut of the gun clockwise

until connection is tight.

Broken o-ring or

plastic insert.

Visit www.karcher-help.com or locate a

service center at

www.karcher-service.com.

Pump Is Noisy Not enough gas or

engine oil.

Check that hoses and fittings are air

tight. Turn off machine and purge pump

by squeezing trigger gun until a steady

flow of water emerges through the

nozzle.

Water Leaks

From Pump

(Up To 10 Drop

Per Minute Is

Permissible)

Loose fittings. Check fittings.

Water seals are

damaged or worn.

Visit www.karcher-help.com or locate a

service center at

www.karcher-service.com.

Thermal protection

device is activated.

Thermal protection device will auto reset.

Do not run pump for more than 5 minutes

without spraying.

Oil Drip Oil seals are

damaged or worn.

Visit www.karcher-help.com or locate a

service center at

www.karcher-service.com.

Symptom Cause Solution

La page charge ...

Kärcher G 3000K Manuel utilisateur

Kärcher G 3000K Manuel utilisateur

dans d''autres langues

Documents connexes