Universal Electronics RF4CE Series Manuel utilisateur

Universal Electronics
Marque
Universal Electronics
Modèle
RF4CE Series
Taper
Manuel utilisateur
ADAPTEUR PAIRING INSTRUCTIONS
UNIVERSAL RF4CE SERIAL ADAPTER
123
456
789
0
GUIDE
INFO
MENU
EXIT
PAGE
MUTE
TVDTA
POWER
LAST
L
A
N
G
5
Press and hold in the PAIR button for 5 seconds until Red
light blinks twice and release the PAIR button.
If you are having issues pairing please visit
www.urcsupport.com/rf for a list of set-top boxes that are
not compatible with the RF4CE Adapter.
IR INPUT
IR INPUT
Press and release PAIR
button on the Adapter.
Press the MENU key on
the remote control. When
the remote is paired.
Enter the 5 digit code for
your brand of Set-top box
(see below)
Motorola/Arris
Pace
Cisco
Evolution
Nagravision
Samsung
Technicolor
01376
01982
01877
02479
02873
01877
01877
01982
For additional support on pairing, please visit us at:
www.urcsupport.com/RF
PAIRING RESET
PAIRING INSTRUCTIONS
UNIVERSAL RF4CE SERIAL ADAPTER
3
14
2Press and hold SETUP on
the remote control until
LED blinks twice.
Make sure Adapter is
connected to the IR port on
the back of the Set-Top Box.
Ensure that the RF4CE Adapter is fully
inserted into the IR port.
for your set-top box, the correct 5-digit
code must be entered immediately after
pairing is completed.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in
accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
approval of manufacturer could void the user's authority to operate this equipment.
For Industry Canada
Industry Canada statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
MUG4869 REV B
Ensure that the remote is an RF remote
by checking the bottom case for an RF
mark and/or FCC ID. If neither are
present, the remote is most likely not
compatible with the RF4CE Adapter.
Tip:
Tip:
Tip:
Tip:
Scientic Atlanta
COX DTA 04315
RÉINITIALISATION DE L’APPAIRAGE /
MUG4869 REV B
INSTRUCTIONS D’APPAIRAGE / INSTRUCCIONES DE ASOCIACIÓN
ADAPTATEUR SÉRIE UNIVERSEL RF4CE /
ADAPTADOR SERIAL RF4CE UNIVERSAL REESTABLECER LA ASOCIACIÓN
3
14
123
456
789
0
GUIDE
INFO
MENU
EXIT
PAGE
MUTE
TVDTA
POWER
LAST
L
A
N
G
25
Appuyez pendant 5 secondes sur le bouton PAIR jusqu’à ce que la
lumière rouge clignote deux fois, puis relâchez.
Presione y sostenga el botón PAIR durante 5 segundos hasta que
la luz roja parpadee dos veces; luego, suelte el botón PAIR.
Appuyez de manière
prolongée sur la touche
SETUP de la
télécommande jusqu’à ce
que la DEL clignote deux
fois, puis relâchez.
Presione y sostenga SETUP
remoto hasta que el LED
parpadee dos veces; luego,
suelte SETUP.
Assurez-vous que l'adapta-
teur est connecté au port IR
à l’arrière du décodeur.
Asegúrese de que el adapta-
dor esté enchufado en el
puerto IR en la parte posterior
Appuyez momentanément
sur le bouton PAIR de
l’adaptateur.
Oprima y suelte el botón
PAIR (asociar) en el
adaptador.
Appuyez sur la touche
MENU de la télécommande.
L’appairage de la
télécommande est terminé
lorsque la lumière rouge
clignote deux fois.
Presione la tecla MENU en
el control remoto. Cuando
la luz roja parpadee dos
veces el control remoto
estará asociado.
Saisissez le code à 5
votre décodeur à partir de
la liste suivante.
Ingrese el código de 5
dígitos correspondiente a
la marca de su
opciones que siguen.
Pour une aide supplémentaire sur l'appairage, veuillez vous rendre à :
www.urcsupport.com/RF
Para ayuda adicional sobre cómo asociar dispositvos visítenos en:
www.urcsupport.com/RF
Assurez-vous que la télécommande est une télécommande RF en
aucune, alors très probablement la télécommande n'est pas compatible
avec l'adaptateur RF4CE.
Veillez à ce que l'adaptateur RF4CE soit entièrement inséré dans le port IR.
inferior de la caja las marcas RF o FCC ID. Si no las encuentra, es muy
factible que el control no sea compatible con el adaptador RF4CE.
Asegúrese de que el adaptador RF4CE esté totalmente insertado en el
puerto IR.
código de 5 dígitos inmediatamente después de completar la asociación.
Consejo:Conseil/
Consejo:Conseil/
Consejo:Conseil/
CONSEJO
CONSEIL/
IR INPUT
IR INPUT
Motorola/Arris
Pace
Cisco
Evolution
Nagravision
Samsung
Technicolor
01376
01982
01877
02479
02873
01877
01877
01982
Scientic Atlanta
COX DTA 04315
  • Page 1 1
  • Page 2 2

Universal Electronics RF4CE Series Manuel utilisateur

Universal Electronics
Marque
Universal Electronics
Modèle
RF4CE Series
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents